Flow metering entries in IEEE 802.1Qci is an optional function for a
flow filtering module. Flow metering is two rates two buckets and three
color marker to policing the frames. This patch only enable one rate one
bucket and in color blind mode. Flow metering instance are as
specified in the algorithm in MEF 10.3 and in Bandwidth Profile
Parameters. They are:

a) Flow meter instance identifier. An integer value identifying the flow
meter instance. The patch use the police 'index' as thin value.
b) Committed Information Rate (CIR), in bits per second. This patch use
the 'rate_bytes_ps' represent this value.
c) Committed Burst Size (CBS), in octets. This patch use the 'burst'
represent this value.
d) Excess Information Rate (EIR), in bits per second.
e) Excess Burst Size per Bandwidth Profile Flow (EBS), in octets.
And plus some other parameters. This patch set EIR/EBS default disable
and color blind mode.

v1->v2 changes:
- Use div_u64() as division replace the '/' report:

All errors (new ones prefixed by >>):

   ld: drivers/net/ethernet/freescale/enetc/enetc_qos.o: in function `enetc_flowmeter_hw_set':
>> enetc_qos.c:(.text+0x66): undefined reference to `__udivdi3'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware device may include more than one police entry. Specifying the
action's index make it possible for several tc filters to share the same
police action when installing the filters.

Propagate this index to device drivers through the flow offload
intermediate representation, so that drivers could share a single
hardware policer between multiple filters.

v1->v2 changes:
- Update the commit message suggest by Ido Schimmel <idosch@idosch.org>
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Base on the tc flower offload police action add max frame size by the
parameter 'mtu'. Tc flower device driver working by the IEEE 802.1Qci
stream filter can implement the max frame size filtering. Add it to the
current hardware tc flower stearm filter driver.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Current police offloading support the 'burst'' and 'rate_bytes_ps'. Some
hardware own the capability to limit the frame size. If the frame size
larger than the setting, the frame would be dropped. For the police
action itself already accept the 'mtu' parameter in tc command. But not
extend to tc flower offloading. So extend 'mtu' to tc flower offloading.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nikolay Aleksandrov says:

====================
net: bridge: fdb activity tracking

This set adds extensions needed for EVPN multi-homing proper and
efficient mac sync. User-space (e.g. FRR) needs to be able to track
non-dynamic entry activity on per-fdb basis depending if a tracked fdb is
currently peer active or locally active and needs to be able to add new
peer active fdb (static + track + inactive) without refreshing it to get
real activity tracking. Patch 02 adds a new NDA attribute - NDA_FDB_EXT_ATTRS
to avoid future pollution of NDA attributes by bridge or vxlan. New
bridge/vxlan specific fdb attributes are embedded in NDA_FDB_EXT_ATTRS,
which is used in patch 03 to pass the new NFEA_ACTIVITY_NOTIFY attribute
which controls if an fdb should be tracked and also reflects its current
state when dumping. It is treated as a bitfield, current valid bits are:
 1 - mark an entry for activity tracking
 2 - mark an entry as inactive to avoid multiple notifications and
     reflect state properly

Patch 04 adds the ability to avoid refreshing an entry when changing it
via the NFEA_DONT_REFRESH flag. That allows user-space to mark a static
entry for tracking and keep its real activity unchanged.
The set has been extensively tested with FRR and those changes will
be upstreamed if/after it gets accepted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When we modify or create a new fdb entry sometimes we want to avoid
refreshing its activity in order to track it properly. One example is
when a mac is received from EVPN multi-homing peer by FRR, which doesn't
want to change local activity accounting. It makes it static and sets a
flag to track its activity.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the ability to notify about activity of any entries
(static, permanent or ext_learn). EVPN multihoming peers need it to
properly and efficiently handle mac sync (peer active/locally active).
We add a new NFEA_ACTIVITY_NOTIFY attribute which is used to dump the
current activity state and to control if static entries should be monitored
at all. We use 2 bits - one to activate fdb entry tracking (disabled by
default) and the second to denote that an entry is inactive. We need
the second bit in order to avoid multiple notifications of inactivity.
Obviously this makes no difference for dynamic entries since at the time
of inactivity they get deleted, while the tracked non-dynamic entries get
the inactive bit set and get a notification.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add an attribute to NDA which will contain all future fdb-specific
attributes in order to avoid polluting the NDA namespace with e.g.
bridge or vxlan specific attributes. The attribute is called
NDA_FDB_EXT_ATTRS and the structure would look like:
 [NDA_FDB_EXT_ATTRS] = {
    [NFEA_xxx]
 }
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We can just pass ndm as an argument instead of its fields separately.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: phy: mscc: PHC and timestamping support

This series aims at adding support for PHC and timestamping operations
in the MSCC PHY driver, for the VSC858x and VSC8575. Those PHYs are
capable of timestamping in 1-step and 2-step for both L2 and L4 traffic.

As of this series, only IPv4 support was implemented when using L4 mode.
This is because of an hardware limitation which prevents us for
supporting both IPv4 and IPv6 at the same time. Implementing support for
IPv6 should be quite easy (I do have the modifications needed for the
hardware configuration) but I did not see a way to retrieve this
information in hwtstamp(). What would you suggest?

Those PHYs are distributed in hardware packages containing multiple
times the PHY. The VSC8584 for example is composed of 4 PHYs. With
hardware packages, parts of the logic is usually common and one of the
PHY has to be used for some parts of the initialization. Following this
logic, the 1588 blocks of those PHYs are shared between two PHYs and
accessing the registers has to be done using the "base" PHY of the
group. This is handled thanks to helpers in the PTP code (and locks).
We also need the MDIO bus lock while performing a single read or write
to the 1588 registers as the read/write are composed of multiple MDIO
transactions (and we don't want other threads updating the page).

To get and set the PHC time, a GPIO has to be used and changes are only
retrieved or committed when on a rising edge. The same GPIO is shared by
all PHYs, so the granularity of the lock protecting it has to be
different from the ones protecting the 1588 registers (the VSC8584 PHY
has 2 1588 blocks, and a single load/save pin).

Patch 1 extends the recently added helpers to share information between
PHYs of the same hardware package; to allow having part of the probe to
be shared (in addition to the already supported init part). This will be
used when adding support for PHC/TS to initialize locks.

Patches 2 and 3 are mostly cosmetic.

Patch 4 takes into account the 1588 block in the MACsec initialization,
to allow having both the MACsec and 1588 blocks initialized on a running
system.

Patches 5 and 6 add support for PHC and timestamping operations in the
MSCC driver. An initialization of the 1588 block (plus all the registers
definition; and helpers) is added first; and then comes a patch to
implement the PHC and timestamping API.

Patches 7 and 8 add the required hardware description for device trees,
to be able to use the load/save GPIO pin on the PCB120 board.

To use this on a PCB120 board, two other series are needed and have
already been sent upstream (one is merged). There are no dependency
between all those series.

Since v3:
  - Fixed a SKB leak.
  - Removed ts_lock from the init, as TS and PHC operations aren't
    registered at this time.
  - Refectored the ts_base_addr/phy intialization.
  - Cleaned up the ingr/egr latencies definitons.
  - Fixed a comment about locking and the shared GPIO.
  - A few cosmetic fixes.

Since v2:
  - Removed explicit inlines from .c files.
  - Fixed three warnings.

Since v1:
  - Removed checks in rxtstamp/txtstamp as skb cannot be NULL here.
  - Reworked get_ptp_header_rx/get_ptp_header.
  - Reworked the locking logic between the PHC and timestamping
    operations.
  - Fixed a compilation issue on x86 reported by Jakub.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a description of the load/save GPIN pin, used in the
VSC8584 PHY for timestamping operations. The related pinctrl description
is also added.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A new optional property can be used to reference the load/save GPIO,
used for PTP hardware clock (PHC) operations. This patch documents it in
the binding documentation.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for PHC and timestamping operations for the MSCC
PHY. PTP 1-step and 2-step modes are supported, over Ethernet and UDP.

To get and set the PHC time, a GPIO has to be used and changes are only
retrieved or committed when on a rising edge. The same GPIO is shared by
all PHYs, so the granularity of the lock protecting it has to be
different from the ones protecting the 1588 registers (the VSC8584 PHY
has 2 1588 blocks, and a single load/save pin).
Co-developed-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the first parts of the 1588 support in the MSCC PHY,
with registers definition and the 1588 block initialization.

Those PHYs are distributed in hardware packages containing multiple
times the PHY. The VSC8584 for example is composed of 4 PHYs. With
hardware packages, parts of the logic is usually common and one of the
PHY has to be used for some parts of the initialization. Following this
logic, the 1588 blocks of those PHYs are shared between two PHYs and
accessing the registers has to be done using the "base" PHY of the
group. This is handled thanks to helpers in the PTP code (and locks).
We also need the MDIO bus lock while performing a single read or write
to the 1588 registers as the read/write are composed of multiple MDIO
transactions (and we don't want other threads updating the page).
Co-developed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch takes in account the use of the 1588 block in the MACsec
initialization, as a conditional configuration has to be done (when the
1588 block is used).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a define for the 0x8000 magic value used to perform
enable/disable actions on the "token ring clock". The patch is only
cosmetic.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

All headers in the MSCC PHY driver have been copied and pasted from the
original mscc.c file. However the information is not necessarily
correct, as in the MACsec support. Fix this.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shared PHYs (PHYs in the same hardware package) may have shared
registers and their drivers would usually need to share information.
There is currently a way to have a shared (part of the) init, by using
phy_package_init_once(). This patch extends the logic to share parts of
the probe to allow sharing the initialization of locks or resources
retrieval.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rahul Lakkireddy says:

====================
cxgb4: fix more warnings reported by sparse

Patch 1 ensures all callers take on-chip memory lock when flashing
PHY firmware to fix lock context imbalance warnings.

Patch 2 moves all static arrays in header file to respective C file
in device dump collection path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Move all arrays related to device dump in header file to C file.
Also, move the function that shares the arrays to the same C file.

Fixes following warnings reported by make W=1 in several places:
cudbg_entity.h:513:18: warning: 't6_hma_ireg_array' defined but not
used [-Wunused-const-variable=]
  513 | static const u32 t6_hma_ireg_array[][IREG_NUM_ELEM] = {

Fixes: a7975a2f ("cxgb4: collect register dump")
Fixes: 17b332f4 ("cxgb4: add support to read serial flash")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Access to on-chip memory for flashing PHY firmware must always
be synchronized. So, ensure the callers take on-chip memory lock.

Also fixes following sparse warning:
sge.c:1641:26: warning: context imbalance in 't4_load_phy_fw' -
different lock contexts for basic block

Fixes: 01b69614 ("cxgb4: Add PHY firmware support for T420-BT cards")
Fixes: 4ee339e1 ("cxgb4: add support to flash PHY image")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Run rxtimestamp as part of TEST_PROGS. Analogous to other tests, add
new rxtimestamp.sh wrapper script, so that the test runs isolated
from background traffic in a private network namespace.

Also ignore failures of test case #6 by default. This case verifies
that a receive timestamp is not reported if timestamp reporting is
enabled for a socket, but generation is disabled. Receive timestamp
generation has to be enabled globally, as no associated socket is
known yet. A background process that enables rx timestamp generation
therefore causes a false positive. Ntpd is one example that does.

Add a "--strict" option to cause failure in the event that any test
case fails, including test #6. This is useful for environments that
are known to not have such background processes.

Tested:
make -C tools/testing/selftests TARGETS="net" run_tests
Signed-off-by: Tanner Love <tannerlove@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ThunderboltIP protocol currently has two flags from which we only
support and set match frags ID. The first flag is reserved for full E2E
flow control. Add a comment that clarifies them.
Suggested-by: Yehezkel Bernat <yehezkelshb@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calvin Johnson says:

====================
ACPI support for xgmac_mdio drivers.

This patch series provides ACPI support for xgmac_mdio driver.

Changes in v3:
- handle case MDIOBUS_NO_CAP

Changes in v2:
- Reserve "0" to mean that no mdiobus capabilities have been declared.
- bus->id: change to appropriate printk format specifier
- clean up xgmac_acpi_match
- clariy platform_get_resource() usage with comments
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since we know the xgmac hardware always has a c45
compliant bus, let's try scanning for c22 capable
PHYs first. If we fail to find any, then it will
fall back to c45 automatically.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ACPI support for xgmac MDIO bus registration while maintaining
the existing DT support.

The function mdiobus_register() inside of_mdiobus_register(), brings
up all the PHYs on the mdio bus and attach them to the bus.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The mdiobus_scan logic is currently hardcoded to only
work with c22 devices. This works fairly well in most
cases, but its possible that a c45 device doesn't respond
despite being a standard phy. If the parent hardware
is capable, it makes sense to scan for c22 devices before
falling back to c45.

As we want this to reflect the capabilities of the STA,
lets add a field to the mii_bus structure to represent
the capability. That way devices can opt into the extended
scanning. Existing users should continue to default to c22
only scanning as long as they are zero'ing the structure
before use.
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vaibhav Gupta says:

====================
ethernet: dec: tulip: use generic power management

Linux Kernel Mentee: Remove Legacy Power Management.

The purpose of this patch series is to remove legacy power management
callbacks and invocation of PCI helper functions, from tulip ethernet drivers.

With legacy PM, drivers themselves are responsible for handling the device's
power states. And they do this with the help of PCI helper functions like
pci_enable/disable_device(), pci_set/restore_state(), pci_set_powr_state(), etc.
which is not recommended.

In generic PM, all the required tasks are handled by PCI core and drivers need
to perform device-specific operations only.

All patches are compile-tested only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

With the support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI states
changes and device's power state themselves.

Legacy PM involves usage of PCI helper functions like pci_enable_wake()
which is no longer recommended.

Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI
states changes and device's power state themselves.

Earlier, .suspend() and .resume() were invoking pci_disable_device()
and pci_enable_device() respectively to manage the device's power state.
driver also invoked pci_save/restore_state() and pci_set_power_sitate().
With generic PM, it is no longer needed. The driver is expected to just
implement driver-specific operations and leave power transitions to PCI
core.

Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI states
changes and device's power state themselves.

Earlier, .suspend() and .resume() were invoking pci_disable_device()
and pci_enable_device() respectively to manage the device's power state.
With generic PM, it is no longer needed. The driver is expected to just
implement driver-specific operations and leave power transitions to PCI
core.

Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With stable support of generic PM callbacks, drivers no longer need to use
legacy .suspend() and .resume() in which they had to maintain PCI states
changes and device's power state themselves.

Earlier, .resume() was invoking pci_enable_device(). Drivers should not
call PCI legacy helper functions, hence, it was removed. This should not
change the behavior of the device as this function is called by PCI core
if somehow pm_ops is not able to bind with the driver, else, required tasks
are managed by the core itself.

Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With legacy PM hooks, it was the responsibility of a driver to manage PCI
states and also the device's power state. The generic approach is to let the
PCI core handle the work.

The legacy suspend() and resume() were making use of
pci_read/write_config_dword() to enable/disable wol. Driver editing
configuration registers of a device is not recommended. Thus replace them
all with device_wakeup_enable/disable().

Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vaibhav Gupta says:

====================
ethernet: amd: Convert to generic power management

Linux Kernel Mentee: Remove Legacy Power Management.

The purpose of this patch series is to remove legacy power management callbacks
from amd ethernet drivers.

The callbacks performing suspend() and resume() operations are still calling
pci_save_state(), pci_set_power_state(), etc. and handling the power management
themselves, which is not recommended.

The conversion requires the removal of the those function calls and change the
callback definition accordingly and make use of dev_pm_ops structure.

All patches are compile-tested only.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use dev_pm_ops structure to call generic suspend() and resume() callbacks.

Drivers should avoid saving device register and/or change power states
using PCI helper functions. With the generic approach, all these are handled
by PCI core.

Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Drivers should not save device registers and/or change the power state of
the device. As per the generic PM approach, these are handled by PCI core.

The driver should support dev_pm_ops callbacks and bind them to pci_driver.

Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove legacy PM callbacks and use generic operations. With legacy code,
drivers were responsible for handling PCI PM operations like
pci_save_state(). In generic code, all these are handled by PCI core.

The generic suspend() and resume() are called at the same point the legacy
ones were called. Thus, it does not affect the normal functioning of the
driver.

Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

dev cannot be NULL here since its already being accessed
before. Remove the redundant null check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

skb cannot be NULL here since its already being accessed
before: sock_net(skb->sk). Remove the redundant null check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>