- 01 Apr, 2014 40 commits
-
-
Tejun Heo authored
commit ecd75ad5 upstream. For some reason, some early WD drives spin up and down drives erratically when the link is put into slumber mode which can reduce the life expectancy of the device significantly. Unfortunately, we don't have full list of devices and given the nature of the issue it'd be better to err on the side of false positives than the other way around. Let's disable LPM on all WD devices which match one of the known problematic model prefixes and are SATA-I. As horkage list doesn't support matching SATA capabilities, this is implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is set for the known prefixes and sets the latter if the matched device is SATA-I. Note that this isn't optimal as this disables all LPM operations and partial link power state reportedly works fine on these; however, the way LPM is implemented in libata makes it difficult to precisely map libata LPM setting to specific link power state. Well, these devices are already fairly outdated. Let's just disable whole LPM for now. Signed-off-by:
Tejun Heo <tj@kernel.org> Reported-and-tested-by:
Nikos Barkas <levelwol@gmail.com> Reported-and-tested-by:
Ioannis Barkas <risc4all@yahoo.com> References: https://bugzilla.kernel.org/show_bug.cgi?id=57211 [bwh: Backported to 3.2: - Adjust context - Use literal 76 instead of ATA_ID_SATA_CAPABILITY] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Prarit Bhargava authored
commit da6139e4 upstream. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=64791 When a cpu is downed on a system, the irqs on the cpu are assigned to other cpus. It is possible, however, that when a cpu is downed there aren't enough free vectors on the remaining cpus to account for the vectors from the cpu that is being downed. This results in an interesting "overflow" condition where irqs are "assigned" to a CPU but are not handled. For example, when downing cpus on a 1-64 logical processor system: <snip> [ 232.021745] smpboot: CPU 61 is now offline [ 238.480275] smpboot: CPU 62 is now offline [ 245.991080] ------------[ cut here ]------------ [ 245.996270] WARNING: CPU: 0 PID: 0 at net/sched/sch_generic.c:264 dev_watchdog+0x246/0x250() [ 246.005688] NETDEV WATCHDOG: p786p1 (ixgbe): transmit queue 0 timed out [ 246.013070] Modules linked in: lockd sunrpc iTCO_wdt iTCO_vendor_support sb_edac ixgbe microcode e1000e pcspkr joydev edac_core lpc_ich ioatdma ptp mdio mfd_core i2c_i801 dca pps_core i2c_core wmi acpi_cpufreq isci libsas scsi_transport_sas [ 246.037633] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.12.0+ #14 [ 246.044451] Hardware name: Intel Corporation S4600LH ........../SVRBD-ROW_T, BIOS SE5C600.86B.01.08.0003.022620131521 02/26/2013 [ 246.057371] 0000000000000009 ffff88081fa03d40 ffffffff8164fbf6 ffff88081fa0ee48 [ 246.065728] ffff88081fa03d90 ffff88081fa03d80 ffffffff81054ecc ffff88081fa13040 [ 246.074073] 0000000000000000 ffff88200cce0000 0000000000000040 0000000000000000 [ 246.082430] Call Trace: [ 246.085174] <IRQ> [<ffffffff8164fbf6>] dump_stack+0x46/0x58 [ 246.091633] [<ffffffff81054ecc>] warn_slowpath_common+0x8c/0xc0 [ 246.098352] [<ffffffff81054fb6>] warn_slowpath_fmt+0x46/0x50 [ 246.104786] [<ffffffff815710d6>] dev_watchdog+0x246/0x250 [ 246.110923] [<ffffffff81570e90>] ? dev_deactivate_queue.constprop.31+0x80/0x80 [ 246.119097] [<ffffffff8106092a>] call_timer_fn+0x3a/0x110 [ 246.125224] [<ffffffff8106280f>] ? update_process_times+0x6f/0x80 [ 246.132137] [<ffffffff81570e90>] ? dev_deactivate_queue.constprop.31+0x80/0x80 [ 246.140308] [<ffffffff81061db0>] run_timer_softirq+0x1f0/0x2a0 [ 246.146933] [<ffffffff81059a80>] __do_softirq+0xe0/0x220 [ 246.152976] [<ffffffff8165fedc>] call_softirq+0x1c/0x30 [ 246.158920] [<ffffffff810045f5>] do_softirq+0x55/0x90 [ 246.164670] [<ffffffff81059d35>] irq_exit+0xa5/0xb0 [ 246.170227] [<ffffffff8166062a>] smp_apic_timer_interrupt+0x4a/0x60 [ 246.177324] [<ffffffff8165f40a>] apic_timer_interrupt+0x6a/0x70 [ 246.184041] <EOI> [<ffffffff81505a1b>] ? cpuidle_enter_state+0x5b/0xe0 [ 246.191559] [<ffffffff81505a17>] ? cpuidle_enter_state+0x57/0xe0 [ 246.198374] [<ffffffff81505b5d>] cpuidle_idle_call+0xbd/0x200 [ 246.204900] [<ffffffff8100b7ae>] arch_cpu_idle+0xe/0x30 [ 246.210846] [<ffffffff810a47b0>] cpu_startup_entry+0xd0/0x250 [ 246.217371] [<ffffffff81646b47>] rest_init+0x77/0x80 [ 246.223028] [<ffffffff81d09e8e>] start_kernel+0x3ee/0x3fb [ 246.229165] [<ffffffff81d0989f>] ? repair_env_string+0x5e/0x5e [ 246.235787] [<ffffffff81d095a5>] x86_64_start_reservations+0x2a/0x2c [ 246.242990] [<ffffffff81d0969f>] x86_64_start_kernel+0xf8/0xfc [ 246.249610] ---[ end trace fb74fdef54d79039 ]--- [ 246.254807] ixgbe 0000:c2:00.0 p786p1: initiating reset due to tx timeout [ 246.262489] ixgbe 0000:c2:00.0 p786p1: Reset adapter Last login: Mon Nov 11 08:35:14 from 10.18.17.119 [root@(none) ~]# [ 246.792676] ixgbe 0000:c2:00.0 p786p1: detected SFP+: 5 [ 249.231598] ixgbe 0000:c2:00.0 p786p1: NIC Link is Up 10 Gbps, Flow Control: RX/TX [ 246.792676] ixgbe 0000:c2:00.0 p786p1: detected SFP+: 5 [ 249.231598] ixgbe 0000:c2:00.0 p786p1: NIC Link is Up 10 Gbps, Flow Control: RX/TX (last lines keep repeating. ixgbe driver is dead until module reload.) If the downed cpu has more vectors than are free on the remaining cpus on the system, it is possible that some vectors are "orphaned" even though they are assigned to a cpu. In this case, since the ixgbe driver had a watchdog, the watchdog fired and notified that something was wrong. This patch adds a function, check_vectors(), to compare the number of vectors on the CPU going down and compares it to the number of vectors available on the system. If there aren't enough vectors for the CPU to go down, an error is returned and propogated back to userspace. v2: Do not need to look at percpu irqs v3: Need to check affinity to prevent counting of MSIs in IOAPIC Lowest Priority Mode v4: Additional changes suggested by Gong Chen. v5/v6/v7/v8: Updated comment text Signed-off-by:
Prarit Bhargava <prarit@redhat.com> Link: http://lkml.kernel.org/r/1389613861-3853-1-git-send-email-prarit@redhat.comReviewed-by:
Gong Chen <gong.chen@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: Michel Lespinasse <walken@google.com> Cc: Seiji Aguchi <seiji.aguchi@hds.com> Cc: Yang Zhang <yang.z.zhang@Intel.com> Cc: Paul Gortmaker <paul.gortmaker@windriver.com> Cc: Janet Morgan <janet.morgan@intel.com> Cc: Tony Luck <tony.luck@intel.com> Cc: Ruiv Wang <ruiv.wang@gmail.com> Cc: Gong Chen <gong.chen@linux.intel.com> Signed-off-by:
H. Peter Anvin <hpa@linux.intel.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
NeilBrown authored
commit 9f97e4b1 upstream. Before a write starts we set a bit in the write-intent bitmap. When the write completes we clear that bit if the write was successful to all devices. However if the write wasn't fully successful we should not clear the bit. If the faulty drive is subsequently re-added, the fact that the bit is still set ensure that we will re-write the data that is missing. This logic is mediated by the STRIPE_DEGRADED flag - we only clear the bitmap bit when this flag is not set. Currently we correctly set the flag if a write starts when some devices are failed or missing. But we do *not* set the flag if some device failed during the write attempt. This is wrong and can result in clearing the bit inappropriately. So: set the flag when a write fails. This bug has been present since bitmaps were introduces, so the fix is suitable for any -stable kernel. Reported-by:
Ethan Wilson <ethan.wilson@shiftmail.org> Signed-off-by:
NeilBrown <neilb@suse.de> [bwh: Backported to 3.2: adjust context, indentation] Signed-off-by:
-
Marcelo Tosatti authored
commit 9ed96e87 upstream. Limit PIT timer frequency similarly to the limit applied by LAPIC timer. Reviewed-by:
Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by:
Marcelo Tosatti <mtosatti@redhat.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> [bwh: Backported to 3.2: - Adjust context - s/ps->period/pt->period/] Signed-off-by:
-
Mikulas Patocka authored
commit 2995fa78 upstream. This reverts commit be35f486 ("dm: wait until embedded kobject is released before destroying a device") and provides an improved fix. The kobject release code that calls the completion must be placed in a non-module file, otherwise there is a module unload race (if the process calling dm_kobject_release is preempted and the DM module unloaded after the completion is triggered, but before dm_kobject_release returns). To fix this race, this patch moves the completion code to dm-builtin.c which is always compiled directly into the kernel if BLK_DEV_DM is selected. The patch introduces a new dm_kobject_holder structure, its purpose is to keep the completion and kobject in one place, so that it can be accessed from non-module code without the need to export the layout of struct mapped_device to that code. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> [bwh: Backported to 3.2: - Adjust context - Remove paranoid check of container_of() result in dm_get_from_kobject(), which would now be incorrect - Include <linux/export.h> in dm-builtin.c, included indirectly upstream] Signed-off-by:
-
Peter Chen authored
commit feffe09f upstream. According to Freescale imx28 Errata, "ENGR119653 USB: ARM to USB register error issue", All USB register write operations must use the ARM SWP instruction. So, we implement a special ehci_write for imx28. Discussion for it at below: http://marc.info/?l=linux-usb&m=137996395529294&w=2 Without this patcheset, imx28 works unstable at high AHB bus loading. If the bus loading is not high, the imx28 usb can work well at the most of time. There is a IC errata for this problem, usually, we consider IC errata is a problem not a new feature, and this workaround is needed for that, so we need to add them to stable tree 3.11+. Cc: robert.hodaszi@digi.com Signed-off-by:
Peter Chen <peter.chen@freescale.com> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Tested-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2:adjust context] Signed-off-by:
-
Weston Andros Adamson authored
commit 78b19bae upstream. Don't check for -NFS4ERR_NOTSUPP, it's already been mapped to -ENOTSUPP by nfs4_stat_to_errno. This allows the client to mount v4.1 servers that don't support SECINFO_NO_NAME by falling back to the "guess and check" method of nfs4_find_root_sec. Signed-off-by:
Weston Andros Adamson <dros@primarydata.com> Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Larry Finger authored
commit f87f960b upstream. Reported-by:
Jan Prinsloo <janroot@gmail.com> Tested-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit a4c35ed2 upstream. The synchronization needed after ftrace_ops are unregistered must happen after the callback is disabled from becing called by functions. The current location happens after the function is being removed from the internal lists, but not after the function callbacks were disabled, leaving the functions susceptible of being called after their callbacks are freed. This affects perf and any externel users of function tracing (LTTng and SystemTap). Fixes: cdbe61bf "ftrace: Allow dynamically allocated function tracers" Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> [bwh: Backported to 3.2: drop change for control ops] Signed-off-by:
-
Steven Rostedt authored
commit 7614c3dc upstream. The function tracer uses preempt_disable/enable_notrace() for synchronization between reading registered ftrace_ops and unregistering them. Most of the ftrace_ops are global permanent structures that do not require this synchronization. That is, ops may be added and removed from the hlist but are never freed, and wont hurt if a synchronization is missed. But this is not true for dynamically created ftrace_ops or control_ops, which are used by the perf function tracing. The problem here is that the function tracer can be used to trace kernel/user context switches as well as going to and from idle. Basically, it can be used to trace blind spots of the RCU subsystem. This means that even though preempt_disable() is done, a synchronize_sched() will ignore CPUs that haven't made it out of user space or idle. These can include functions that are being traced just before entering or exiting the kernel sections. To implement the RCU synchronization, instead of using synchronize_sched() the use of schedule_on_each_cpu() is performed. This means that when a dynamically allocated ftrace_ops, or a control ops is being unregistered, all CPUs must be touched and execute a ftrace_sync() stub function via the work queues. This will rip CPUs out from idle or in dynamic tick mode. This only happens when a user disables perf function tracing or other dynamically allocated function tracers, but it allows us to continue to debug RCU and context tracking with function tracing. Link: http://lkml.kernel.org/r/1369785676.15552.55.camel@gandalf.local.home Cc: "Paul E. McKenney" <paulmck@us.ibm.com> Cc: Tejun Heo <tj@kernel.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Peter Zijlstra <peterz@infradead.org> Acked-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by:
-
Ludovic Desroches authored
commit 66b512ed upstream. With some SDIO devices, timeout errors can happen when reading data. To solve this issue, the DMA transfer has to be activated before sending the command to the device. This order is incorrect in PDC mode. So we have to take care if we are using DMA or PDC to know when to send the MMC command. Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
Chris Ball <cjb@laptop.org> Signed-off-by:
-
Hartmut Knaack authored
commit 38408d05 upstream. Only free an IRQ in error_free_irq, if it has been requested previously. Signed-off-by:
Hartmut Knaack <knaack.h@gmx.de> Acked-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
Jonathan Cameron <jic23@kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit 80ab8eae upstream. The PCI devices with DMA masks smaller than 32bit should enable CONFIG_ZONE_DMA. Since the recent change of page allocator, page allocations via dma_alloc_coherent() with the limited DMA mask bits may fail more frequently, ended up with no available buffers, when CONFIG_ZONE_DMA isn't enabled. With CONFIG_ZONE_DMA, the system has much more chance to obtain such pages. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=68221Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Larry Finger authored
commit 3a21f00a upstream. The latest version of NetworkManager does not recognize the device as wireless without this change. Signed-off-by:
-
Michel Dänzer authored
commit 37016951 upstream. It's never allocated on systems without an ATOMBIOS or COMBIOS ROM. Should fix an oops I encountered while resetting the GPU after a lockup on my PowerBook with an RV350. Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Lars-Peter Clausen authored
commit e20970ad upstream. The driver defines ADAU1701_SEROCTL_WORD_LEN_16 as 0x10 while it should be b10, so 0x2. This patch fixes it. Reported-by:
Magnus Reftel <magnus.reftel@lockless.no> Signed-off-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
-
Joe Thornber authored
commit 12c91a5c upstream. When extending a low level space map we should update nr_blocks at the start so the new space is used for the index entries. Otherwise extend can fail, e.g.: sm_metadata_extend call sequence that fails: -> sm_ll_extend -> dm_tm_new_block -> dm_sm_new_block -> sm_bootstrap_new_block => returns -ENOSPC because smm->begin == smm->ll.nr_blocks Signed-off-by:
Joe Thornber <ejt@redhat.com> Signed-off-by:
-
Mikulas Patocka authored
commit be35f486 upstream. There may be other parts of the kernel holding a reference on the dm kobject. We must wait until all references are dropped before deallocating the mapped_device structure. The dm_kobject_release method signals that all references are dropped via completion. But dm_kobject_release doesn't free the kobject (which is embedded in the mapped_device structure). This is the sequence of operations: * when destroying a DM device, call kobject_put from dm_sysfs_exit * wait until all users stop using the kobject, when it happens the release method is called * the release method signals the completion and should return without delay * the dm device removal code that waits on the completion continues * the dm device removal code drops the dm_mod reference the device had * the dm device removal code frees the mapped_device structure that contains the kobject Using kobject this way should avoid the module unload race that was mentioned at the beginning of this thread: https://lkml.org/lkml/2014/1/4/83Signed-off-by:
-
Stephen Warren authored
commit 3685f19e upstream. Tegra chips have 4 or 5 identical UART modules embedded. UARTs C..E have their MODEM-control signals tied off to a static state. However UARTs A and B can optionally route those signals to/from package pins, depending on the exact pinmux configuration. When these signals are not routed to package pins, false interrupts may trigger either temporarily, or permanently, all while not showing up in the IIR; it will read as NO_INT. This will eventually lead to the UART IRQ being disabled due to unhandled interrupts. When this happens, the kernel may print e.g.: irq 68: nobody cared (try booting with the "irqpoll" option) In order to prevent this, enable UART_BUG_NOMSR. This prevents UART_IER_MSI from being enabled, which prevents the false interrupts from triggering. In practice, this is not needed under any of the following conditions: * On Tegra chips after Tegra30, since the HW bug has apparently been fixed. * On UARTs C..E since their MODEM control signals are tied to the correct static state which doesn't trigger the issue. * On UARTs A..B if the MODEM control signals are routed out to package pins, since they will then carry valid signals. However, we ignore these exceptions for now, since they are only relevant if a board actually hooks up more than a 4-wire UART, and no currently supported board does this. If we ever support a board that does, we can refine the algorithm that enables UART_BUG_NOMSR to take those exceptions into account, and/or read a flag from DT/... that indicates that the board has hooked up and pinmux'd more than a 4-wire UART. Reported-by: Olof Johansson <olof@lixom.net> # autotester Signed-off-by:
Stephen Warren <swarren@nvidia.com> Signed-off-by:
-
Colin Leitner authored
commit c1f15196 upstream. Genuine FTDI chips support only CS7/8. A previous fix in commit 8704211f ("USB: ftdi_sio: fixed handling of unsupported CSIZE setting") enforced this limitation and reported it back to userspace. However, certain types of smartcard readers depend on specific driver behaviour that requests 0 data bits (not 5) to change into a different operating mode if CS5 has been set. This patch reenables this behaviour for all FTDI devices. Tagged to be added to stable, because it affects a lot of users of embedded systems which rely on these readers to work properly. Reported-by:
Heinrich Siebmanns <H.Siebmanns@t-online.de> Tested-by:
Colin Leitner <colin.leitner@gmail.com> Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
-
Alex Deucher authored
commit d1951782 upstream. The hw i2c engines are disabled by default as the current implementation is still experimental. Print a warning when users enable it so that it's obvious when the option is enabled. v2: check for non-0 rather than 1 Signed-off-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
-
Tetsuo Handa authored
commit 8ed81460 upstream. Hello. I got below leak with linux-3.10.0-54.0.1.el7.x86_64 . [ 681.903890] kmemleak: 5538 new suspected memory leaks (see /sys/kernel/debug/kmemleak) Below is a patch, but I don't know whether we need special handing for undoing ebitmap_set_bit() call. ---------- >>From fe97527a90fe95e2239dfbaa7558f0ed559c0992 Mon Sep 17 00:00:00 2001 From: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Date: Mon, 6 Jan 2014 16:30:21 +0900 Subject: [PATCH] SELinux: Fix memory leak upon loading policy Commit 2463c26d "SELinux: put name based create rules in a hashtable" did not check return value from hashtab_insert() in filename_trans_read(). It leaks memory if hashtab_insert() returns error. unreferenced object 0xffff88005c9160d0 (size 8): comm "systemd", pid 1, jiffies 4294688674 (age 235.265s) hex dump (first 8 bytes): 57 0b 00 00 6b 6b 6b a5 W...kkk. backtrace: [<ffffffff816604ae>] kmemleak_alloc+0x4e/0xb0 [<ffffffff811cba5e>] kmem_cache_alloc_trace+0x12e/0x360 [<ffffffff812aec5d>] policydb_read+0xd1d/0xf70 [<ffffffff812b345c>] security_load_policy+0x6c/0x500 [<ffffffff812a623c>] sel_write_load+0xac/0x750 [<ffffffff811eb680>] vfs_write+0xc0/0x1f0 [<ffffffff811ec08c>] SyS_write+0x4c/0xa0 [<ffffffff81690419>] system_call_fastpath+0x16/0x1b [<ffffffffffffffff>] 0xffffffffffffffff However, we should not return EEXIST error to the caller, or the systemd will show below message and the boot sequence freezes. systemd[1]: Failed to load SELinux policy. Freezing. Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by:
Eric Paris <eparis@redhat.com> Signed-off-by:
Paul Moore <pmoore@redhat.com> Signed-off-by:
-
Weston Andros Adamson authored
commit 6ff33b7d upstream. When a task enters call_refreshresult with status 0 from call_refresh and !rpcauth_uptodatecred(task) it enters call_refresh again with no rate-limiting or max number of retries. Instead of trying forever, make use of the retry path that other errors use. This only seems to be possible when the crrefresh callback is gss_refresh_null, which only happens when destroying the context. To reproduce: 1) mount with sec=krb5 (or sec=sys with krb5 negotiated for non FSID specific operations). 2) reboot - the client will be stuck and will need to be hard rebooted BUG: soft lockup - CPU#0 stuck for 22s! [kworker/0:2:46] Modules linked in: rpcsec_gss_krb5 nfsv4 nfs fscache ppdev crc32c_intel aesni_intel aes_x86_64 glue_helper lrw gf128mul ablk_helper cryptd serio_raw i2c_piix4 i2c_core e1000 parport_pc parport shpchp nfsd auth_rpcgss oid_registry exportfs nfs_acl lockd sunrpc autofs4 mptspi scsi_transport_spi mptscsih mptbase ata_generic floppy irq event stamp: 195724 hardirqs last enabled at (195723): [<ffffffff814a925c>] restore_args+0x0/0x30 hardirqs last disabled at (195724): [<ffffffff814b0a6a>] apic_timer_interrupt+0x6a/0x80 softirqs last enabled at (195722): [<ffffffff8103f583>] __do_softirq+0x1df/0x276 softirqs last disabled at (195717): [<ffffffff8103f852>] irq_exit+0x53/0x9a CPU: 0 PID: 46 Comm: kworker/0:2 Not tainted 3.13.0-rc3-branch-dros_testing+ #4 Hardware name: VMware, Inc. VMware Virtual Platform/440BX Desktop Reference Platform, BIOS 6.00 07/31/2013 Workqueue: rpciod rpc_async_schedule [sunrpc] task: ffff8800799c4260 ti: ffff880079002000 task.ti: ffff880079002000 RIP: 0010:[<ffffffffa0064fd4>] [<ffffffffa0064fd4>] __rpc_execute+0x8a/0x362 [sunrpc] RSP: 0018:ffff880079003d18 EFLAGS: 00000246 RAX: 0000000000000005 RBX: 0000000000000007 RCX: 0000000000000007 RDX: 0000000000000007 RSI: ffff88007aecbae8 RDI: ffff8800783d8900 RBP: ffff880079003d78 R08: ffff88006e30e9f8 R09: ffffffffa005a3d7 R10: ffff88006e30e7b0 R11: ffff8800783d8900 R12: ffffffffa006675e R13: ffff880079003ce8 R14: ffff88006e30e7b0 R15: ffff8800783d8900 FS: 0000000000000000(0000) GS:ffff88007f200000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f3072333000 CR3: 0000000001a0b000 CR4: 00000000001407f0 Stack: ffff880079003d98 0000000000000246 0000000000000000 ffff88007a9a4830 ffff880000000000 ffffffff81073f47 ffff88007f212b00 ffff8800799c4260 ffff8800783d8988 ffff88007f212b00 ffffe8ffff604800 0000000000000000 Call Trace: [<ffffffff81073f47>] ? trace_hardirqs_on_caller+0x145/0x1a1 [<ffffffffa00652d3>] rpc_async_schedule+0x27/0x32 [sunrpc] [<ffffffff81052974>] process_one_work+0x211/0x3a5 [<ffffffff810528d5>] ? process_one_work+0x172/0x3a5 [<ffffffff81052eeb>] worker_thread+0x134/0x202 [<ffffffff81052db7>] ? rescuer_thread+0x280/0x280 [<ffffffff81052db7>] ? rescuer_thread+0x280/0x280 [<ffffffff810584a0>] kthread+0xc9/0xd1 [<ffffffff810583d7>] ? __kthread_parkme+0x61/0x61 [<ffffffff814afd6c>] ret_from_fork+0x7c/0xb0 [<ffffffff810583d7>] ? __kthread_parkme+0x61/0x61 Code: e8 87 63 fd e0 c6 05 10 dd 01 00 01 48 8b 43 70 4c 8d 6b 70 45 31 e4 a8 02 0f 85 d5 02 00 00 4c 8b 7b 48 48 c7 43 48 00 00 00 00 <4c> 8b 4b 50 4d 85 ff 75 0c 4d 85 c9 4d 89 cf 0f 84 32 01 00 00 And the output of "rpcdebug -m rpc -s all": RPC: 61 call_refresh (status 0) RPC: 61 call_refresh (status 0) RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0 RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0 RPC: 61 call_refreshresult (status 0) RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0 RPC: 61 call_refreshresult (status 0) RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0 RPC: 61 call_refresh (status 0) RPC: 61 call_refreshresult (status 0) RPC: 61 call_refresh (status 0) RPC: 61 call_refresh (status 0) RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0 RPC: 61 call_refreshresult (status 0) RPC: 61 call_refresh (status 0) RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0 RPC: 61 call_refresh (status 0) RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0 RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0 RPC: 61 call_refreshresult (status 0) RPC: 61 call_refresh (status 0) RPC: 61 call_refresh (status 0) RPC: 61 call_refresh (status 0) RPC: 61 call_refresh (status 0) RPC: 61 call_refreshresult (status 0) RPC: 61 refreshing RPCSEC_GSS cred ffff88007a413cf0 Signed-off-by:
Weston Andros Adamson <dros@netapp.com> Signed-off-by:
-
Takashi Iwai authored
commit 770bd4bf upstream. The lack of comma leads to the wrong channel for an SPDIF channel. Unfortunately this wasn't caught by compiler because it's still a valid expression. Reported-by:
Alexander Aristov <aristov.alexander@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit 440ebade upstream. Fix ring-indicator (RI) status-bit definition, which was defined as CTS, effectively preventing RI-changes from being detected while reporting false RI status. This bug predates git. Signed-off-by:
-
Mikhail Zolotaryov authored
commit 0e16114f upstream. The USB storage operation of Nokia Asha 502 Dual SIM smartphone running Asha Platform 1.1.1 is unreliable in respect of data consistency (i.e. transfered files are corrupted). A similar issue is described here: http://discussions.nokia.com/t5/Asha-and-other-Nokia-Series-30/Nokia-301-USB-transfers-and-corrupted-files/td-p/1974170 The workaround is (MAX_SECTORS_64): rmmod usb_storage && modprobe usb_storage quirks=0421:06aa:m The patch adds the tested device to the unusual list permanently. Signed-off-by:
Mikhail Zolotaryov <lebon@lebon.org.ua> Signed-off-by:
-
Rahul Bedarkar authored
commit 7d5c1b9c upstream. Add support for iBall 3.5G connect usb modem. $lsusb Bus 002 Device 006: ID 1c9e:9605 OMEGA TECHNOLOGY $usb-devices T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1c9e ProdID=9605 Rev=00.00 S: Manufacturer=USB Modem S: Product=USB Modem S: SerialNumber=1234567890ABCDEF C: #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option I: If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage Signed-off-by:
Rahul Bedarkar <rahulbedarkar89@gmail.com> Suggested-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Johan Hovold authored
commit 623c8263 upstream. Some PL2303 devices are known to lose bytes if you change serial settings even to the same values as before. Avoid this by comparing the encoded settings with the previsouly used ones before configuring the device. The common case was fixed by commit bf5e5834 ("pl2303: Fix mode switching regression"), but this problem was still possible to trigger, for instance, by using the TCSETS2-interface to repeatedly request 115201 baud, which gets mapped to 115200 and thus always triggers a settings update. Cc: Frank Schäfer <fschaefer.oss@googlemail.com> Signed-off-by:
-
Michael Grzeschik authored
commit 05664777 upstream. The ecc_stats.corrected count variable will already be incremented in the above framework-layer just after this callback. Signed-off-by:
Michael Grzeschik <m.grzeschik@pengutronix.de> Signed-off-by:
Brian Norris <computersforpeace@gmail.com> Signed-off-by:
-
Li Zefan authored
commit 8afb1474 upstream. /sys/kernel/slab/:t-0000048 # cat cpu_slabs 231 N0=16 N1=215 /sys/kernel/slab/:t-0000048 # cat slabs 145 N0=36 N1=109 See, the number of slabs is smaller than that of cpu slabs. The bug was introduced by commit 49e22585 ("slub: per cpu cache for partial pages"). We should use page->pages instead of page->pobjects when calculating the number of cpu partial slabs. This also fixes the mapping of slabs and nodes. As there's no variable storing the number of total/active objects in cpu partial slabs, and we don't have user interfaces requiring those statistics, I just add WARN_ON for those cases. Acked-by:
Christoph Lameter <cl@linux.com> Reviewed-by:
Wanpeng Li <liwanp@linux.vnet.ibm.com> Signed-off-by:
Li Zefan <lizefan@huawei.com> Signed-off-by:
Pekka Enberg <penberg@kernel.org> Signed-off-by:
-
Borislav Petkov authored
commit d5a1c7e3 upstream. 41c7f742 ("rtc: Disable the alarm in the hardware (v2)") added the functionality to disable the RTC wake alarm when shutting down the box. However, there are at least two b0rked BIOSes we know about: https://bugzilla.novell.com/show_bug.cgi?id=812592 https://bugzilla.novell.com/show_bug.cgi?id=805740 where, when wakeup alarm is enabled in the BIOS, the machine reboots automatically right after shutdown, regardless of what wakeup time is programmed. Bisecting the issue lead to this patch so disable its functionality with a DMI quirk only for those boxes. Cc: Brecht Machiels <brecht@mos6581.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: John Stultz <john.stultz@linaro.org> Cc: Rabin Vincent <rabin.vincent@stericsson.com> Signed-off-by:
Borislav Petkov <bp@suse.de> [jstultz: Changed variable name for clarity, added extra dmi entry] Tested-by:
Brecht Machiels <brecht@mos6581.org> Tested-by:
John Stultz <john.stultz@linaro.org> Signed-off-by:
-
Dave Young authored
commit a7f84f03 upstream. Current code check boot service region with kernel text region by: start+size >= __pa_symbol(_text) The end of the above region should be start + size - 1 instead. I see this problem in ovmf + Fedora 19 grub boot: text start: 1000000 md start: 800000 md size: 800000 Signed-off-by:
Dave Young <dyoung@redhat.com> Acked-by:
Toshi Kani <toshi.kani@hp.com> Tested-by:
Matt Fleming <matt.fleming@intel.com> [bwh: Backported to 3.2: s/__pa_symbol/virt_to_phys/] Signed-off-by:
-
Yegor Yefremov authored
commit 48c0247d upstream. Signed-off-by:
Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by:
-
Yegor Yefremov authored
commit 1e9deb11 upstream. add support for 400Hv3, 410Hv3 and 800Hv3 Signed-off-by:
Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 5ac64ba1 upstream. As the dvb-frontend kthread can be called anytime, it can race with some get status ioctl. So, it seems better to avoid one to race with the other while reading a 32 bits register. I can't see any other reason for having a mutex there at I2C, except to provide such kind of protection, as the I2C core already has a mutex to protect I2C transfers. Note: instead of this approach, it could eventually remove the dib8000 specific mutex for it, and either group the 4 ops into one xfer or to manually control the I2C mutex. The main advantage of the current approach is that the changes are smaller and more puntual. Signed-off-by:
Mauro Carvalho Chehab <m.chehab@samsung.com> Signed-off-by:
Patrick Boettcher <pboettcher@kernellabs.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
张君 authored
commit 4d90b819 upstream. Signed-off-by:
Jun zhang <zhang.jun92@zte.com.cn> Signed-off-by:
-
Vijaya Mohan Guvva authored
commit dcaf9aed upstream. Bfa driver crash is observed while pushing the firmware on to chinook quad port card due to uninitialized bfi_image_ct2 access which gets initialized only for CT2 ASIC based cards after request_firmware(). For quard port chinook (CT2 ASIC based), bfi_image_ct2 is not getting initialized as there is no check for chinook PCI device ID before request_firmware and instead bfi_image_cb is initialized as it is the default case for card type check. This patch includes changes to read the right firmware for quad port chinook. Signed-off-by:
Vijaya Mohan Guvva <vmohan@brocade.com> Signed-off-by:
James Bottomley <JBottomley@Parallels.com> Signed-off-by:
-
Malcolm Priestley authored
commit 8f248dae upstream. byBBPreEDIndex value is initially 0, this means that from cold BBvUpdatePreEDThreshold is never set. This means that sensitivity may be in an ambiguous state, failing to scan any wireless points or at least distant ones. Signed-off-by:
Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by:
-
Sebastian Andrzej Siewior authored
commit d6a48452 upstream. In commit 85747f ("PATCH] parport: add NetMOS 9805 support") Max added the PCI ID for NetMOS 9805 based on a Debian bug report from 2k4 which was at the v2.4.26 time frame. The patch made into 2.6.14. Shortly before that patch akpm merged commit 296d3c78 ("[PATCH] Support NetMOS based PCI cards providing serial and parallel ports") which made into v2.6.9-rc1. Now we have two different entries for the same PCI id. I have here the NetMos 9805 which claims to support SPP/EPP/ECP mode. This patch takes Max's entry for titan_1284p1 (base != -1 specifies the ioport for ECP mode) and replaces akpm's entry for netmos_9805 which specified -1 (=none). Both share the same PCI-ID (my card has subsystem 0x1000 / 0x0020 so it should match PCI_ANY). While here I also drop the entry for titan_1284p2 which is the same as netmos_9815. Cc: Maximilian Attems <maks@stro.at> Signed-off-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Paul Moore authored
commit 5c6c2681 upstream. Due to difficulty in arriving at the proper security label for TCP SYN-ACK packets in selinux_ip_postroute(), we need to check packets while/before they are undergoing XFRM transforms instead of waiting until afterwards so that we can determine the correct security label. Reported-by:
Janak Desai <Janak.Desai@gtri.gatech.edu> Signed-off-by:
-
