- 21 Jul, 2019 40 commits
-
-
Arnd Bergmann authored
commit fd5de272 upstream. As kernelci.org reports, this function is not used in vdk_hs38_defconfig: arch/arc/kernel/unwind.c:188:14: warning: 'unw_hdr_alloc' defined but not used [-Wunused-function] Fixes: bc79c9a7 ("ARC: dw2 unwind: Reinstante unwinding out of modules") Link: https://kernelci.org/build/id/5d1cae3f59b514300340c132/logs/ Cc: stable@vger.kernel.org Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thomas Gleixner authored
commit f8a8fe61 upstream. Quite some time ago the interrupt entry stubs for unused vectors in the system vector range got removed and directly mapped to the spurious interrupt vector entry point. Sounds reasonable, but it's subtly broken. The spurious interrupt vector entry point pushes vector number 0xFF on the stack which makes the whole logic in __smp_spurious_interrupt() pointless. As a consequence any spurious interrupt which comes from a vector != 0xFF is treated as a real spurious interrupt (vector 0xFF) and not acknowledged. That subsequently stalls all interrupt vectors of equal and lower priority, which brings the system to a grinding halt. This can happen because even on 64-bit the system vector space is not guaranteed to be fully populated. A full compile time handling of the unused vectors is not possible because quite some of them are conditonally populated at runtime. Bring the entry stubs back, which wastes 160 bytes if all stubs are unused, but gains the proper handling back. There is no point to selectively spare some of the stubs which are known at compile time as the required code in the IDT management would be way larger and convoluted. Do not route the spurious entries through common_interrupt and do_IRQ() as the original code did. Route it to smp_spurious_interrupt() which evaluates the vector number and acts accordingly now that the real vector numbers are handed in. Fixup the pr_warn so the actual spurious vector (0xff) is clearly distiguished from the other vectors and also note for the vectored case whether it was pending in the ISR or not. "Spurious APIC interrupt (vector 0xFF) on CPU#0, should never happen." "Spurious interrupt vector 0xed on CPU#1. Acked." "Spurious interrupt vector 0xee on CPU#1. Not pending!." Fixes: 2414e021 ("x86: Avoid building unused IRQ entry stubs") Reported-by:
Jan Kiszka <jan.kiszka@siemens.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Jan Beulich <jbeulich@suse.com> Link: https://lkml.kernel.org/r/20190628111440.550568228@linutronix.deSigned-off-by:
-
Thomas Gleixner authored
commit b7107a67 upstream. Since the rework of the vector management, warnings about spurious interrupts have been reported. Robert provided some more information and did an initial analysis. The following situation leads to these warnings: CPU 0 CPU 1 IO_APIC interrupt is raised sent to CPU1 Unable to handle immediately (interrupts off, deep idle delay) mask() ... free() shutdown() synchronize_irq() clear_vector() do_IRQ() -> vector is clear Before the rework the vector entries of legacy interrupts were statically assigned and occupied precious vector space while most of them were unused. Due to that the above situation was handled silently because the vector was handled and the core handler of the assigned interrupt descriptor noticed that it is shut down and returned. While this has been usually observed with legacy interrupts, this situation is not limited to them. Any other interrupt source, e.g. MSI, can cause the same issue. After adding proper synchronization for level triggered interrupts, this can only happen for edge triggered interrupts where the IO-APIC obviously cannot provide information about interrupts in flight. While the spurious warning is actually harmless in this case it worries users and driver developers. Handle it gracefully by marking the vector entry as VECTOR_SHUTDOWN instead of VECTOR_UNUSED when the vector is freed up. If that above late handling happens the spurious detector will not complain and switch the entry to VECTOR_UNUSED. Any subsequent spurious interrupt on that line will trigger the spurious warning as before. Fixes: 464d1230 ("x86/vector: Switch IOAPIC to global reservation mode") Reported-by:
Robert Hodaszi <Robert.Hodaszi@digi.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>- Tested-by:
-
Thomas Gleixner authored
commit dfe0cf8b upstream. When an interrupt is shut down in free_irq() there might be an inflight interrupt pending in the IO-APIC remote IRR which is not yet serviced. That means the interrupt has been sent to the target CPUs local APIC, but the target CPU is in a state which delays the servicing. So free_irq() would proceed to free resources and to clear the vector because synchronize_hardirq() does not see an interrupt handler in progress. That can trigger a spurious interrupt warning, which is harmless and just confuses users, but it also can leave the remote IRR in a stale state because once the handler is invoked the interrupt resources might be freed already and therefore acknowledgement is not possible anymore. Implement the irq_get_irqchip_state() callback for the IO-APIC irq chip. The callback is invoked from free_irq() via __synchronize_hardirq(). Check the remote IRR bit of the interrupt and return 'in flight' if it is set and the interrupt is configured in level mode. For edge mode the remote IRR has no meaning. As this is only meaningful for level triggered interrupts this won't cure the potential spurious interrupt warning for edge triggered interrupts, but the edge trigger case does not result in stale hardware state. This has to be addressed at the vector/interrupt entry level seperately. Fixes: 464d1230 ("x86/vector: Switch IOAPIC to global reservation mode") Reported-by:
-
Thomas Gleixner authored
commit 62e04686 upstream. free_irq() ensures that no hardware interrupt handler is executing on a different CPU before actually releasing resources and deactivating the interrupt completely in a domain hierarchy. But that does not catch the case where the interrupt is on flight at the hardware level but not yet serviced by the target CPU. That creates an interesing race condition: CPU 0 CPU 1 IRQ CHIP interrupt is raised sent to CPU1 Unable to handle immediately (interrupts off, deep idle delay) mask() ... free() shutdown() synchronize_irq() release_resources() do_IRQ() -> resources are not available That might be harmless and just trigger a spurious interrupt warning, but some interrupt chips might get into a wedged state. Utilize the existing irq_get_irqchip_state() callback for the synchronization in free_irq(). synchronize_hardirq() is not using this mechanism as it might actually deadlock unter certain conditions, e.g. when called with interrupts disabled and the target CPU is the one on which the synchronization is invoked. synchronize_irq() uses it because that function cannot be called from non preemtible contexts as it might sleep. No functional change intended and according to Marc the existing GIC implementations where the driver supports the callback should be able to cope with that core change. Famous last words. Fixes: 464d1230 ("x86/vector: Switch IOAPIC to global reservation mode") Reported-by:
Marc Zyngier <marc.zyngier@arm.com> Tested-by:
-
Thomas Gleixner authored
commit 1d21f2af upstream. The function might sleep, so it cannot be called from interrupt context. Not even with care. Signed-off-by:
-
Thomas Gleixner authored
commit 4001d8e8 upstream. When interrupts are shutdown, they are immediately deactivated in the irqdomain hierarchy. While this looks obviously correct there is a subtle issue: There might be an interrupt in flight when free_irq() is invoking the shutdown. This is properly handled at the irq descriptor / primary handler level, but the deactivation might completely disable resources which are required to acknowledge the interrupt. Split the shutdown code and deactivate the interrupt after synchronization in free_irq(). Fixup all other usage sites where this is not an issue to invoke the combined shutdown_and_deactivate() function instead. This still might be an issue if the interrupt in flight servicing is delayed on a remote CPU beyond the invocation of synchronize_irq(), but that cannot be handled at that level and needs to be handled in the synchronize_irq() context. Fixes: f8264e34 ("irqdomain: Introduce new interfaces to support hierarchy irqdomains") Reported-by:
-
Vinod Koul authored
[ Upstream commit 8f9fab48 ] DIV_ROUND_UP_ULL adds the two arguments and then invokes DIV_ROUND_DOWN_ULL. But on a 32bit system the addition of two 32 bit values can overflow. DIV_ROUND_DOWN_ULL does it correctly and stashes the addition into a unsigned long long so cast the result to unsigned long long here to avoid the overflow condition. [akpm@linux-foundation.org: DIV_ROUND_UP_ULL must be an rval] Link: http://lkml.kernel.org/r/20190625100518.30753-1-vkoul@kernel.orgSigned-off-by:
Vinod Koul <vkoul@kernel.org> Reviewed-by:
Andrew Morton <akpm@linux-foundation.org> Cc: Bjorn Andersson <bjorn.andersson@linaro.org> Cc: Randy Dunlap <rdunlap@infradead.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Andrea Arcangeli authored
[ Upstream commit 1bf4580e ] Commit 5eed6f1d ("fork,memcg: fix crash in free_thread_stack on memcg charge fail") corrected two instances, but there was a third instance of this bug. Without setting tsk->stack, if memcg_charge_kernel_stack fails, it'll execute free_thread_stack() on a dangling pointer. Enterprise kernels are compiled with VMAP_STACK=y so this isn't critical, but custom VMAP_STACK=n builds should have some performance advantage, with the drawback of risking to fail fork because compaction didn't succeed. So as long as VMAP_STACK=n is a supported option it's worth fixing it upstream. Link: http://lkml.kernel.org/r/20190619011450.28048-1-aarcange@redhat.com Fixes: 9b6f7e16 ("mm: rework memcg kernel stack accounting") Signed-off-by:
Andrea Arcangeli <aarcange@redhat.com> Reviewed-by:
Rik van Riel <riel@surriel.com> Acked-by:
Roman Gushchin <guro@fb.com> Acked-by:
Michal Hocko <mhocko@suse.com> Signed-off-by:
-
Yafang Shao authored
[ Upstream commit 432b1de0 ] In dump_oom_summary() oc->constraint is used to show oom_constraint_text, but it hasn't been set before. So the value of it is always the default value 0. We should inititialize it before. Bellow is the output when memcg oom occurs, before this patch: oom-kill:constraint=CONSTRAINT_NONE,nodemask=(null), cpuset=/,mems_allowed=0,oom_memcg=/foo,task_memcg=/foo,task=bash,pid=7997,uid=0 after this patch: oom-kill:constraint=CONSTRAINT_MEMCG,nodemask=(null), cpuset=/,mems_allowed=0,oom_memcg=/foo,task_memcg=/foo,task=bash,pid=13681,uid=0 Link: http://lkml.kernel.org/r/1560522038-15879-1-git-send-email-laoar.shao@gmail.com Fixes: ef8444ea ("mm, oom: reorganize the oom report in dump_header") Signed-off-by:
Yafang Shao <laoar.shao@gmail.com> Acked-by:
-
Nicolas Boichat authored
[ Upstream commit 9d957a95 ] During suspend/resume, mtk_eint_mask may be called while wake_mask is active. For example, this happens if a wake-source with an active interrupt handler wakes the system: irq/pm.c:irq_pm_check_wakeup would disable the interrupt, so that it can be handled later on in the resume flow. However, this may happen before mtk_eint_do_resume is called: in this case, wake_mask is loaded, and cur_mask is restored from an older copy, re-enabling the interrupt, and causing an interrupt storm (especially for level interrupts). Step by step, for a line that has both wake and interrupt enabled: 1. cur_mask[irq] = 1; wake_mask[irq] = 1; EINT_EN[irq] = 1 (interrupt enabled at hardware level) 2. System suspends, resumes due to that line (at this stage EINT_EN == wake_mask) 3. irq_pm_check_wakeup is called, and disables the interrupt => EINT_EN[irq] = 0, but we still have cur_mask[irq] = 1 4. mtk_eint_do_resume is called, and restores EINT_EN = cur_mask, so it reenables EINT_EN[irq] = 1 => interrupt storm as the driver is not yet ready to handle the interrupt. This patch fixes the issue in step 3, by recording all mask/unmask changes in cur_mask. This also avoids the need to read the current mask in eint_do_suspend, and we can remove mtk_eint_chip_read_mask function. The interrupt will be re-enabled properly later on, sometimes after mtk_eint_do_resume, when the driver is ready to handle it. Fixes: 58a5e1b6 ("pinctrl: mediatek: Implement wake handler and suspend resume") Signed-off-by:
Nicolas Boichat <drinkcat@chromium.org> Acked-by:
Sean Wang <sean.wang@kernel.org> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Eiichi Tsukata authored
[ Upstream commit 33d4a5a7 ] Setting invalid value to /sys/devices/system/cpu/cpuX/hotplug/fail can control `struct cpuhp_step *sp` address, results in the following global-out-of-bounds read. Reproducer: # echo -2 > /sys/devices/system/cpu/cpu0/hotplug/fail KASAN report: BUG: KASAN: global-out-of-bounds in write_cpuhp_fail+0x2cd/0x2e0 Read of size 8 at addr ffffffff89734438 by task bash/1941 CPU: 0 PID: 1941 Comm: bash Not tainted 5.2.0-rc6+ #31 Call Trace: write_cpuhp_fail+0x2cd/0x2e0 dev_attr_store+0x58/0x80 sysfs_kf_write+0x13d/0x1a0 kernfs_fop_write+0x2bc/0x460 vfs_write+0x1e1/0x560 ksys_write+0x126/0x250 do_syscall_64+0xc1/0x390 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x7f05e4f4c970 The buggy address belongs to the variable: cpu_hotplug_lock+0x98/0xa0 Memory state around the buggy address: ffffffff89734300: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00 ffffffff89734380: fa fa fa fa 00 00 00 00 00 00 00 00 00 00 00 00 >ffffffff89734400: 00 00 00 00 fa fa fa fa 00 00 00 00 fa fa fa fa ^ ffffffff89734480: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ffffffff89734500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Add a sanity check for the value written from user space. Fixes: 1db49484 ("smp/hotplug: Hotplug state fail injection") Signed-off-by:
Eiichi Tsukata <devel@etsukata.com> Signed-off-by:
-
Nicolas Boichat authored
[ Upstream commit 35594bc7 ] Before suspending, mtk-eint would set the interrupt mask to the one in wake_mask. However, some of these interrupts may not have a corresponding interrupt handler, or the interrupt may be disabled. On resume, the eint irq handler would trigger nevertheless, and irq/pm.c:irq_pm_check_wakeup would be called, which would try to call irq_disable. However, if the interrupt is not enabled (irqd_irq_disabled(&desc->irq_data) is true), the call does nothing, and the interrupt is left enabled in the eint driver. Especially for level-sensitive interrupts, this will lead to an interrupt storm on resume. If we detect that an interrupt is only in wake_mask, but not in cur_mask, we can just mask it out immediately (as mtk_eint_resume would do anyway at a later stage in the resume sequence, when restoring cur_mask). Fixes: bf22ff45 ("genirq: Avoid unnecessary low level irq function calls") Signed-off-by:
-
Kai-Heng Feng authored
[ Upstream commit 0a95fc73 ] There's a new ALPS touchpad/pointstick combo device that requires MT_CLS_WIN_8_DUAL to make its pointsitck work as a mouse. The device can be found on HP ZBook 17 G5. Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
Jiri Kosina <jkosina@suse.cz> Signed-off-by:
-
Kyle Godbey authored
[ Upstream commit 315ffcc9 ] Add support for Huion HS64 drawing tablet to hid-uclogic Signed-off-by:
Kyle Godbey <me@kyle.ee> Signed-off-by:
-
Oleksandr Natalenko authored
[ Upstream commit dcf768b0 ] I've spotted another Chicony PixArt mouse in the wild, which requires HID_QUIRK_ALWAYS_POLL quirk, otherwise it disconnects each minute. USB ID of this device is 0x04f2:0x0939. We've introduced quirks like this for other models before, so lets add this mouse too. Link: https://github.com/sriemer/fix-linux-mouse#usb-mouse-disconnectsreconnects-every-minute-on-linuxSigned-off-by:
Oleksandr Natalenko <oleksandr@redhat.com> Acked-by:
Sebastian Parschauer <s.parschauer@gmx.de> Signed-off-by:
-
Kirill A. Shutemov authored
[ Upstream commit c1887159 ] __startup_64() uses fixup_pointer() to access global variables in a position-independent fashion. Access to next_early_pgt was wrapped into the helper, but one instance in the 5-level paging branch was missed. GCC generates a R_X86_64_PC32 PC-relative relocation for the access which doesn't trigger the issue, but Clang emmits a R_X86_64_32S which leads to an invalid memory access and system reboot. Fixes: 187e91fe ("x86/boot/64/clang: Use fixup_pointer() to access 'next_early_pgt'") Signed-off-by:
Kirill A. Shutemov <kirill.shutemov@linux.intel.com> Signed-off-by:
-
Kirill A. Shutemov authored
[ Upstream commit 81c7ed29 ] A kernel which boots in 5-level paging mode crashes in a small percentage of cases if KASLR is enabled. This issue was tracked down to the case when the kernel image unpacks in a way that it crosses an 1G boundary. The crash is caused by an overrun of the PMD page table in __startup_64() and corruption of P4D page table allocated next to it. This particular issue is not visible with 4-level paging as P4D page tables are not used. But the P4D and the PUD calculation have similar problems. The PMD index calculation is wrong due to operator precedence, which fails to confine the PMDs in the PMD array on wrap around. The P4D calculation for 5-level paging and the PUD calculation calculate the first index correctly, but then blindly increment it which causes the same issue when a kernel image is located across a 512G and for 5-level paging across a 46T boundary. This wrap around mishandling was introduced when these parts moved from assembly to C. Restore it to the correct behaviour. Fixes: c88d7150 ("x86/boot/64: Rewrite startup_64() in C") Signed-off-by:
-
Milan Broz authored
[ Upstream commit 2eba4e64 ] DM verity should also use DMERR_LIMIT to limit repeat data block corruption messages. Signed-off-by:
Milan Broz <gmazyland@gmail.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Jerome Marchand authored
[ Upstream commit a0651926 ] For the first call to realloc_argv() in dm_split_args(), old_argv is NULL and size is zero. Then memcpy is called, with the NULL old_argv as the source argument and a zero size argument. AFAIK, this is undefined behavior and generates the following warning when compiled with UBSAN on ppc64le: In file included from ./arch/powerpc/include/asm/paca.h:19, from ./arch/powerpc/include/asm/current.h:16, from ./include/linux/sched.h:12, from ./include/linux/kthread.h:6, from drivers/md/dm-core.h:12, from drivers/md/dm-table.c:8: In function 'memcpy', inlined from 'realloc_argv' at drivers/md/dm-table.c:565:3, inlined from 'dm_split_args' at drivers/md/dm-table.c:588:9: ./include/linux/string.h:345:9: error: argument 2 null where non-null expected [-Werror=nonnull] return __builtin_memcpy(p, q, size); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/md/dm-table.c: In function 'dm_split_args': ./include/linux/string.h:345:9: note: in a call to built-in function '__builtin_memcpy' Signed-off-by:
Jerome Marchand <jmarchan@redhat.com> Signed-off-by:
-
Alexandre Belloni authored
[ Upstream commit 4b36082e ] The actual layout for OCELOT_GPIO_ALT[01] when there are more than 32 pins is interleaved, i.e. OCELOT_GPIO_ALT0[0], OCELOT_GPIO_ALT1[0], OCELOT_GPIO_ALT0[1], OCELOT_GPIO_ALT1[1]. Introduce a new REG_ALT macro to facilitate the register offset calculation and use it where necessary. Fixes: da801ab5 pinctrl: ocelot: add MSCC Jaguar2 support Signed-off-by:
Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by:
-
Alexandre Belloni authored
[ Upstream commit f2818ba3 ] The third argument passed to REG is not the correct one and ocelot_gpio_set_direction is not working for pins after 31. Fix that by passing the pin number instead of the modulo 32 value. Fixes: da801ab5 pinctrl: ocelot: add MSCC Jaguar2 support Signed-off-by:
-
Phil Reid authored
[ Upstream commit 6dbc6e6f ] Currently probing of the mcp23s08 results in an error message "detected irqchip that is shared with multiple gpiochips: please fix the driver" This is due to the following: Call to mcp23s08_irqchip_setup() with call hierarchy: mcp23s08_irqchip_setup() gpiochip_irqchip_add_nested() gpiochip_irqchip_add_key() gpiochip_set_irq_hooks() Call to devm_gpiochip_add_data() with call hierarchy: devm_gpiochip_add_data() gpiochip_add_data_with_key() gpiochip_add_irqchip() gpiochip_set_irq_hooks() The gpiochip_add_irqchip() returns immediately if there isn't a irqchip but we added a irqchip due to the previous mcp23s08_irqchip_setup() call. So it calls gpiochip_set_irq_hooks() a second time. Fix this by moving the call to devm_gpiochip_add_data before the call to mcp23s08_irqchip_setup Fixes: 02e389e6 ("pinctrl: mcp23s08: fix irq setup order") Suggested-by:
Marco Felsch <m.felsch@pengutronix.de> Signed-off-by:
Phil Reid <preid@electromag.com.au> Signed-off-by:
-
Sébastien Szymanski authored
[ Upstream commit 3cf10132 ] According to the i.MX6UL/L RM, table 3.1 "ARM Cortex A7 domain interrupt summary", the interrupts for the PWM[1-4] go from 83 to 86. Fixes: b9901fe8 ("ARM: dts: imx6ul: add pwm[1-4] nodes") Signed-off-by:
Sébastien Szymanski <sebastien.szymanski@armadeus.com> Reviewed-by:
Fabio Estevam <festevam@gmail.com> Signed-off-by:
Shawn Guo <shawnguo@kernel.org> Signed-off-by:
-
Sergej Benilov authored
[ Upstream commit 8ac8a010 ] Since commit 605ad7f1 "tcp: refine TSO autosizing", outbound throughput is dramatically reduced for some connections, as sis900 is doing TX completion within idle states only. Make TX completion happen after every transmitted packet. Test: netperf before patch: > netperf -H remote -l -2000000 -- -s 1000000 MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 327680 327680 253.44 0.06 after patch: > netperf -H remote -l -10000000 -- -s 1000000 MIGRATED TCP STREAM TEST from 0.0.0.0 () port 0 AF_INET to 95.223.112.76 () port 0 AF_INET : demo Recv Send Send Socket Socket Message Elapsed Size Size Size Time Throughput bytes bytes bytes secs. 10^6bits/sec 87380 327680 327680 5.38 14.89 Thx to Dave Miller and Eric Dumazet for helpful hints Signed-off-by:
Sergej Benilov <sergej.benilov@googlemail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit aad1dcc4 ] The arc4 crypto is mandatory at ppp_mppe probe time, so let's put a softdep line, so that the corresponding module gets prepared gracefully. Without this, a simple inclusion to initrd via dracut failed due to the missing dependency, for example. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Petr Oros authored
[ Upstream commit 2e5db6eb ] Certain cards in conjunction with certain switches need a little more time for link setup that results in ethtool link test failure after offline test. Patch adds a loop that waits for a link setup finish. Changes in v2: - added fixes header Fixes: 4276e47e ("be2net: Add link test to list of ethtool self tests.") Signed-off-by:
Petr Oros <poros@redhat.com> Reviewed-by:
Ivan Vecera <ivecera@redhat.com> Signed-off-by:
-
Colin Ian King authored
[ Upstream commit ea136a11 ] The left shift of unsigned int cpu_khz will overflow for large values of cpu_khz, so cast it to a long long before shifting it to avoid overvlow. For example, this can happen when cpu_khz is 4194305, i.e. ~4.2 GHz. Addresses-Coverity: ("Unintentional integer overflow") Fixes: 8c3ba8d0 ("x86, apic: ack all pending irqs when crashed/on kexec") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Qian Cai authored
[ Upstream commit 919aef44 ] Compiling a kernel with W=1 generates this warning, arch/x86/platform/efi/quirks.c:731:16: warning: comparison of unsigned expression >= 0 is always true [-Wtype-limits] Fixes: 3425d934 ("efi/x86: Handle page faults occurring while running ...") Signed-off-by:
Qian Cai <cai@lca.pw> Acked-by:
"Prakhya, Sai Praneeth" <sai.praneeth.prakhya@intel.com> Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by:
-
David Howells authored
[ Upstream commit 90fa9b64 ] Fix the cb_break_lock spinlock in afs_volume struct by initialising it when the volume record is allocated. Also rename the lock to cb_v_break_lock to distinguish it from the lock of the same name in the afs_server struct. Without this, the following trace may be observed when a volume-break callback is received: INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. CPU: 2 PID: 50 Comm: kworker/2:1 Not tainted 5.2.0-rc1-fscache+ #3045 Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014 Workqueue: afs SRXAFSCB_CallBack Call Trace: dump_stack+0x67/0x8e register_lock_class+0x23b/0x421 ? check_usage_forwards+0x13c/0x13c __lock_acquire+0x89/0xf73 lock_acquire+0x13b/0x166 ? afs_break_callbacks+0x1b2/0x3dd _raw_write_lock+0x2c/0x36 ? afs_break_callbacks+0x1b2/0x3dd afs_break_callbacks+0x1b2/0x3dd ? trace_event_raw_event_afs_server+0x61/0xac SRXAFSCB_CallBack+0x11f/0x16c process_one_work+0x2c5/0x4ee ? worker_thread+0x234/0x2ac worker_thread+0x1d8/0x2ac ? cancel_delayed_work_sync+0xf/0xf kthread+0x11f/0x127 ? kthread_park+0x76/0x76 ret_from_fork+0x24/0x30 Fixes: 68251f0a ("afs: Fix whole-volume callback handling") Signed-off-by:
David Howells <dhowells@redhat.com> Signed-off-by:
-
Arnd Bergmann authored
[ Upstream commit 27e23d89 ] omap3xxx_prm_enable_io_wakeup() is marked __init, but its caller is not, so we get a warning with clang-8: WARNING: vmlinux.o(.text+0x343c8): Section mismatch in reference from the function omap3xxx_prm_late_init() to the function .init.text:omap3xxx_prm_enable_io_wakeup() The function omap3xxx_prm_late_init() references the function __init omap3xxx_prm_enable_io_wakeup(). This is often because omap3xxx_prm_late_init lacks a __init annotation or the annotation of omap3xxx_prm_enable_io_wakeup is wrong. When building with gcc, omap3xxx_prm_enable_io_wakeup() is always inlined, so we never noticed in the past. Signed-off-by:
Nathan Chancellor <natechancellor@gmail.com> Acked-by:
Tony Lindgren <tony@atomide.com> Reviewed-by:
Andrew Murray <andrew.murray@arm.com> Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
-
Linus Walleij authored
[ Upstream commit 36558020 ] It's a simple typo in the DNS file, which was pretty serious. No scripts were working properly. Fix it up. Signed-off-by:
-
Peter Zijlstra authored
[ Upstream commit 085ebfe9 ] perf_sample_regs_user() uses 'current->mm' to test for the presence of userspace, but this is insufficient, consider use_mm(). A better test is: '!(current->flags & PF_KTHREAD)', exec() clears PF_KTHREAD after it sets the new ->mm but before it drops to userspace for the first time. Possibly obsoletes: bf05fc25 ("powerpc/perf: Fix oops when kthread execs user process") Reported-by:
Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com> Reported-by:
Young Xiao <92siuyang@gmail.com> Signed-off-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Acked-by:
Will Deacon <will.deacon@arm.com> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Frederic Weisbecker <fweisbec@gmail.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Fixes: 4018994f ("perf: Add ability to attach user level registers dump to sample") Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Michael Ellerman authored
[ Upstream commit 16391bfc ] This tests that when a process with a mapping above 512TB forks we correctly separate the parent and child address spaces. This exercises the bug in the context id handling fixed in the previous commit. Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Ran Wang authored
[ Upstream commit 53f2ac9d ] PSCI spec define 1st parameter's bit 16 of function CPU_SUSPEND to indicate CPU State Type: 0 for standby, 1 for power down. In this case, we want to select standby for CPU idle feature. But current setting wrongly select power down and cause CPU SUSPEND fail every time. Need this fix. Fixes: 8897f325 ("arm64: dts: Add support for NXP LS1028A SoC") Signed-off-by:
Ran Wang <ran.wang_1@nxp.com> Signed-off-by:
-
Hans de Goede authored
[ Upstream commit a483fcab ] Starting with ACPI 6.2 bits 1 and 2 of the BGRT status field are no longer reserved. These bits are now used to indicate if the image needs to be rotated before being displayed. The first device using these bits has now shown up (the GPD MicroPC) and the reserved bits check causes us to reject the valid BGRT table on this device. Rather then changing the reserved bits check, allowing only the 2 new bits, instead just completely remove it so that we do not end up with a similar problem when more bits are added in the future. Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Tony Lindgren authored
[ Upstream commit 41b3588d ] If we do a clk_get() for a clock that does not exists, we have _ti_omap4_clkctrl_xlate() return uninitialized data if no match is found. This can be seen in some cases with SLAB_DEBUG enabled: Unable to handle kernel paging request at virtual address 5a5a5a5a ... clk_hw_create_clk.part.33 sysc_notifier_call notifier_call_chain blocking_notifier_call_chain device_add Let's fix this by setting a found flag only when we find a match. Reported-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Fixes: 88a17252 ("clk: ti: add support for clkctrl clocks") Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Tested-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
Heyi Guo authored
[ Upstream commit a050fa54 ] When we run several VMs with PCI passthrough and GICv4 enabled, not pinning vCPUs, we will occasionally see below warnings in dmesg: ITS queue timeout (65440 65504 480) ITS cmd its_build_vmovp_cmd failed The reason for the above issue is that in BUILD_SINGLE_CMD_FUNC: 1. Post the write command. 2. Release the lock. 3. Start to read GITS_CREADR to get the reader pointer. 4. Compare the reader pointer to the target pointer. 5. If reader pointer does not reach the target, sleep 1us and continue to try. If we have several processors running the above concurrently, other CPUs will post write commands while the 1st CPU is waiting the completion. So we may have below issue: phase 1: ---rd_idx-----from_idx-----to_idx--0--------- wait 1us: phase 2: --------------from_idx-----to_idx--0-rd_idx-- That is the rd_idx may fly ahead of to_idx, and if in case to_idx is near the wrap point, rd_idx will wrap around. So the below condition will not be met even after 1s: if (from_idx < to_idx && rd_idx >= to_idx) There is another theoretical issue. For a slow and busy ITS, the initial rd_idx may fall behind from_idx a lot, just as below: ---rd_idx---0--from_idx-----to_idx----------- This will cause the wait function exit too early. Actually, it does not make much sense to use from_idx to judge if to_idx is wrapped, but we need a initial rd_idx when lock is still acquired, and it can be used to judge whether to_idx is wrapped and the current rd_idx is wrapped. We switch to a method of calculating the delta of two adjacent reads and accumulating it to get the sum, so that we can get the real rd_idx from the wrapped value even when the queue is almost full. Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Jason Cooper <jason@lakedaemon.net> Signed-off-by:
Heyi Guo <guoheyi@huawei.com> Signed-off-by:
-
Guo Ren authored
[ Upstream commit db56c512 ] The csky,mpintc could deliver a external irq to one cpu or all cpus, but it couldn't deliver a external irq to a group of cpus with cpu_mask. So we only use auto deliver mode when affinity mask_val is equal to cpu_present_mask. There is no limitation for only two cpus in SMP system. Signed-off-by:
Guo Ren <ren_guo@c-sky.com> Cc: Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Martin Blumenstingl authored
[ Upstream commit 26d65140 ] Amlogic's vendor kernel defines an OPP for the GPU on Meson8b boards with a voltage of 1.15V. It turns out that the vendor kernel relies on the bootloader to set up the voltage. The bootloader however sets a fixed voltage of 1.10V. Amlogic's patched u-boot sources (uboot-2015-01-15-23a3562521) confirm this: $ grep -oiE "VDD(EE|AO)_VOLTAGE[ ]+[0-9]+" board/amlogic/configs/m8b_* board/amlogic/configs/m8b_m100_v1.h:VDDAO_VOLTAGE 1100 board/amlogic/configs/m8b_m101_v1.h:VDDAO_VOLTAGE 1100 board/amlogic/configs/m8b_m102_v1.h:VDDAO_VOLTAGE 1100 board/amlogic/configs/m8b_m200_v1.h:VDDAO_VOLTAGE 1100 board/amlogic/configs/m8b_m201_v1.h:VDDEE_VOLTAGE 1100 board/amlogic/configs/m8b_m201_v1.h:VDDEE_VOLTAGE 1100 board/amlogic/configs/m8b_m202_v1.h:VDDEE_VOLTAGE 1100 Another hint at this is the VDDEE voltage on the EC-100 and Odroid-C1 boards. The VDDEE regulator supplies the Mali GPU. It's basically a copy of the VCCK (CPU supply) which means it's limited to 0.86V to 1.14V. Update the operating voltage of the Mali GPU on Meson8b to 1.10V so it matches with what the vendor u-boot sets. Fixes: c3ea80b6 ("ARM: dts: meson8b: add the Mali-450 MP2 GPU") Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
Kevin Hilman <khilman@baylibre.com> Signed-off-by:
-
