- 12 Jan, 2012 36 commits
-
-
Balaji TK authored
MMC master clock rate can vary for each instance of the MMC controller on the device. Use clk_get_rate instead to get the value. Signed-off-by:
Balaji TK <balajitk@ti.com> Reviewed-by:
Venkatraman S <svenkatr@ti.com> Tested-by:
Hebbar, Gururaja <gururaja.hebbar@ti.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by:
Chris Ball <cjb@laptop.org>
-
Guennadi Liakhovetski authored
Signed-off-by:
Guennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by:
-
Guennadi Liakhovetski authored
This patch converts the sh_mmcif MMC host driver to process requests asynchronously instead of waiting in its .request() method for completion. This is achieved by using threaded IRQs. Signed-off-by:
-
Guennadi Liakhovetski authored
This patch doesn't introduce any functional changes, it only simplifies some code fragments, removes superfluous parameters, fixes typos. Signed-off-by:
-
Guennadi Liakhovetski authored
If an interrupt is coming with both error and data completion status bits set, it has to be handled as an error interrupt, for which error interrupts have to be processed first. The current version of the driver on the contrary doesn't recognise such interrupts as an error event, which leads to data corruption and breaks the error recovery. Signed-off-by:
-
Guennadi Liakhovetski authored
This patch adds a primitive helper to support card hotplug detection on platforms, where a GPIO, capable of producing interrupts, is used for detection of card-insertion and -removal events. Signed-off-by:
-
Guennadi Liakhovetski authored
SD/MMC controllers provide different card insertion and removal detection methods. On some of them the controller itself issues an interrupt, on others polling is used, on yet others auxiliary means are used for this purpose, e.g., a GPIO IRQ. Further, on some systems one of those methods can be chosen at driver probing time and configured in software. E.g., on some systems the SD/MMC controller card hot-plug detection pin can be configured either as a respective controller functions, or an IRQ-capable GPIO. To support such flexible configurations a card hot-plug context is added by this patch. Signed-off-by:
-
Bastian Hecht authored
This patch regroups the code slightly, adds documentation and allows the rtpm counter of MMC_CAP_NEEDS_POLL devices to reach 0 again. Signed-off-by:
Bastian Hecht <hechtb@gmail.com> [g.liakhovetski@gmx.de: restore pm_runtime_get_noresume()] Signed-off-by:
-
Girish K S authored
This patch fixes the wrong comparison before setting the interface voltage in DDR mode. The assignment to the variable ddr before comaprison is either ddr = MMC_1_2V_DDR_MODE; or ddr == MMC_1_8V_DDR_MODE. But the comparison is done with the extended csd value if ddr == EXT_CSD_CARD_TYPE_DDR_1_2V. Signed-off-by:
Girish K S <girish.shivananjappa@linaro.org> Acked-by:
Subhash Jadavani <subhashj@codeaurora.org> Acked-by:
Philip Rakity <prakity@marvell.com> Cc: <stable@kernel.org> Signed-off-by:
-
Jingoo Han authored
Signed-off-by:
Jingoo Han <jg1.han@samsung.com> Signed-off-by:
-
Seungwon Jeon authored
This patch adds the support for predefined multiple block r/w. dw_mmc can support MMC_CAP_CMD23 capability. Signed-off-by:
Seungwon Jeon <tgih.jun@samsung.com> Acked-by:
Will Newton <will.newton@imgtec.com> Signed-off-by:
-
Chris Ball authored
Signed-off-by: -
Seungwon Jeon authored
This patch adds another capabilities field for MMC_CAPS2_XXX. Signed-off-by:
-
Jaehoon Chung authored
This patch modifies dw_mmc to use dev_pm_ops. Signed-off-by:
Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by:
Kyungmin Park <kyungmin.park@samsung.com> Acked-by:
James Hogan <james.hogan@imgtec.com> Signed-off-by:
-
Sujit Reddy Thumma authored
Kill block requests when the host realizes that the card is removed from the slot and is sure that subsequent requests are bound to fail. Do this silently so that the block layer doesn't output unnecessary error messages. Signed-off-by:
Sujit Reddy Thumma <sthumma@codeaurora.org> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Stephen Boyd authored
c31b50e (mmc: core: Use delayed work in clock gating framework, 2011-11-14) missed a few things during review: o A useless pr_info() o milliseconds was written as two words o The sysfs file had units in its output Fix all three problems. Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Cc: Sujit Reddy Thumma <sthumma@codeaurora.org> Signed-off-by:
-
Axel Lin authored
Signed-off-by:
Axel Lin <axel.lin@gmail.com> Acked-by:
-
Johan Rudholm authored
Enable boot partitions to be read-only locked until next power on via a sysfs entry. There will be one sysfs entry for each boot partition: /sys/block/mmcblkXbootY/ro_lock_until_next_power_on Each boot partition is locked by writing 1 to its file. Signed-off-by:
Johan Rudholm <johan.rudholm@stericsson.com> Signed-off-by:
John Beckett <john.beckett@stericsson.com> Signed-off-by:
-
Sangwook Lee authored
Add pm_caps into platform_data. This is power management, usually for SDIO device such as SDIO WLAN. Signed-off-by:
Sangwook Lee <sangwook.lee@samsung.com> Acked-by:
Kukjin Kim <kgene.kim@samsung.com> Signed-off-by:
-
Sangwook Lee authored
sdhci-s3c updates pm_caps from platform data for SDIO PM. Signed-off-by:
-
Adrian Hunter authored
Add a function mmc_detect_card_removed() which upper layers can use to determine immediately if a card has been removed. This function should be called after an I/O request fails so that all queued I/O requests can be errored out immediately instead of waiting for the card device to be removed. Signed-off-by:
-
Cong Wang authored
Signed-off-by:
Cong Wang <amwang@redhat.com> Acked-by:
-
Axel Lin authored
This patch converts the drivers in drivers/mmc/host/* to use the module_platform_driver() macro which makes the code smaller and a bit simpler. Signed-off-by:
"Michał Mirosław" <mirq-linux@rere.qmqm.pl> Acked-by:
David Brown <davidb@codeaurora.org> Acked-by:
Viresh Kumar <viresh.kumar@st.com> Acked-by:
Sascha Hauer <s.hauer@pengutronix.de> Acked-by:
Wolfram Sang <w.sang@pengutronix.de> Acked-by:
Anton Vorontsov <cbouatmailru@gmail.com> Signed-off-by:
-
Lars-Peter Clausen authored
In ancient times it was necessary to manually initialize the bus field of an spi_driver to spi_bus_type. These days this is done in spi_driver_register(), so we can drop the manual assignment. The patch was generated using the following coccinelle semantic patch: // <smpl> @@ identifier _driver; @@ struct spi_driver _driver = { .driver = { - .bus = &spi_bus_type, }, }; // </smpl> Signed-off-by:Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Guennadi Liakhovetski authored
Replace ilog2(__rounddown_pow_of_two(x)) with the equivalent but much simpler fls(x) - 1. Reported-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Johan Rudholm authored
If the read or write buffer size associated with the command sent through the mmc_blk_ioctl is zero, do not prepare data buffer. This enables a ioctl(2) call to for instance send a MMC_SWITCH to set a byte in the ext_csd. Signed-off-by:
-
Tony Lin authored
1ms is enough for hardware to change the clock to stable. 100ms is too long in the tasklet. Signed-off-by:
Tony Lin <tony.lin@freescale.com> CC: Xiaobo Xie <X.Xie@freescale.com> CC: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by:
-
Per Forlin authored
If max_seg_size is unaligned, mmc_test_map_sg() may create sg element sizes that are not aligned with 512 byte. Fix, align max_seg_size at mmc_test_area_init(). Signed-off-by:
Per Forlin <per.forlin@stericsson.com> Signed-off-by:
-
Per Forlin authored
Signed-off-by:
-
Philip Rakity authored
This patch adds support for sdio UHS cards per the version 3.0 spec. UHS mode is only enabled for version 3.0 cards when both the host and the controller support UHS modes. 1.8v signaling support is removed if both the card and the host do not support UHS. This is done to maintain compatibility and some system/card combinations break when 1.8v signaling is enabled when the host does not support UHS. Signed-off-by:
Aaron Lu <Aaron.lu@amd.com> Reviewed-by:
Arindam Nath <arindam.nath@amd.com> Tested-by:
Bing Zhao <bzhao@marvell.com> Signed-off-by:
-
Viresh Kumar authored
Suspend/Resume is missing from sdhci-spear driver. This patch adds support for suspend/resume for this driver. Signed-off-by:
-
Sujit Reddy Thumma authored
Current clock gating framework disables the MCI clock as soon as the request is completed and enables it when a request arrives. This aggressive clock gating framework, when enabled, cause following issues: When there are back-to-back requests from the Queue layer, we unnecessarily end up disabling and enabling the clocks between these requests since 8MCLK clock cycles is a very short duration compared to the time delay between back to back requests reaching the MMC layer. This overhead can effect the overall performance depending on how long the clock enable and disable calls take which is platform dependent. For example on some platforms we can have clock control not on the local processor, but on a different subsystem and the time taken to perform the clock enable/disable can add significant overhead. Also if the host controller driver decides to disable the host clock too when mmc_set_ios function is called with ios.clock=0, it adds additional delay and it is highly possible that the next request had already arrived and unnecessarily blocked in enabling the clocks. This is seen frequently when the processor is executing at high speeds and in multi-core platforms thus reduces the overall throughput compared to if clock gating is disabled. Fix this by delaying turning off the clocks by posting request on delayed workqueue. Also cancel the unscheduled pending work, if any, when there is access to card. sysfs entry is provided to tune the delay as needed, default value set to 200ms. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Chris Ball authored
No functional change; adds macros for card manufacturer IDs. Signed-off-by: -
Giuseppe CAVALLARO authored
This patch is to expose the actual SDCLK frequency in /sys/kernel/debug/mmcX/ios entry. For example, if the max clk for a normal speed card is 20MHz this is reported in /sys/kernel/debug/mmcX/ios. Unfortunately the actual SDCLK frequency (i.e. Baseclock / divisor) is not reported at all: for example, in that case, on Arasan HC, it should be 48/4=12 (MHz). Signed-off-by:
Giuseppe Cavallaro <peppe.cavallaro@st.com> Acked-by:
-
Stefan Nilsson XK authored
This patch allows any block size to be set on the SDIO link, and still have an arbitrary sized packet (adjusted in size by using sdio_align_size) transferred in an optimal way (preferably one transfer). Previously if the block size was larger than the default of 512 bytes and the transfer size was exactly one block size (possibly thanks to using sdio_align_size to get an optimal transfer size), it was sent as a number of byte transfers instead of one block transfer. Also if the number of blocks was (max_blocks * N) + 1, the tranfer would be conducted with a number of blocks and finished off with a number of byte transfers. When doing this change it was also possible to break out the quirk for broken byte mode in a much cleaner way, and collect the logic of when to do byte or block transfer in one function instead of two. Signed-off-by:
Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com> Signed-off-by:
Ulf Hansson <ulf.hansson@stericsson.com> Acked-by:
-
Qiang Liu authored
Add new macros for the high speed 50MHz case, rather than having a confusing reuse of the value for UHS SDR50, which is 100MHz. Reported-by:
-
- 24 Dec, 2011 4 commits
-
-
Greg Ungerer authored
We have a duplicate name and definition for the offset of the thread.info struct within the task struct in our asm-offsets.c code. Remove one of them, and consolidate to use a single define, TASK_INFO. Signed-off-by:
Greg Ungerer <gerg@uclinux.org> Acked-by:
Geert Uytterhoeven <geert@linux-m68k.org>
-
Greg Ungerer authored
The init_task code can be the same for both mmu and non-mmu targets. None of the alignment carried out in the the current init_task code is necessary. The linker script takes care of aligning the init_thread structure to a THREAD SIZE boundary, and that is all we need. So use the init_task.c code for all target types, that makes m68k code consistent with what most other architectures do. Signed-off-by:
-
Greg Ungerer authored
The fasthandler code was removed long ago. Remove the now unused declaration of it. Signed-off-by: -
Mark Brown authored
gpiolib provides __gpio_to_irq() to map gpiolib gpios to interrupts - hook that up on m68k. Signed-off-by:
Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by:
-
