The format is based on /proc/net/icmp and /proc/net/{udp,raw}6.

Compiles and displays reasonable results with CONFIG_IPV6={n,m,y}
Couldn't figure out how to test without CONFIG_PROC_FS enabled.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce a ping_seq_afinfo structure (similar to its UDP
equivalent) and use it to make some of the ping /proc functions
address-family independent. Rename the remaining ping /proc
functions from ping_* to ping_v4_*.

Compiles and displays reasonable results with CONFIG_IPV6={n,m,y}
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

udp6_sock_seq_show and raw6_sock_seq_show are identical, except
the UDP version displays ports and the raw version displays the
protocol. Refactor most of the code in these two functions into
a new common ip6_dgram_sock_seq_show function, in preparation
for using it to display ICMPv6 sockets as well.

Also reduce the indentation in parts of include/net/transp_v6.h
to improve readability.

Compiles and displays reasonable results with CONFIG_IPV6={n,m,y}
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reduce the indentation of most of the functions and make it a
bit more consistent. This allows longer function and arg names
to be consistently indented without wrapping.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pci_enable_device() will set device pm state to D0, so
it's no need to do it again in tg3_init_one().
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct icmp_bxm is a large struct, reduce stack usage
by allocating it on heap.

Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ICMP_PARAMETERPROB is handled by icmp_unreach(); This patch adds
ICMP_PARAMETERPROB to the list of ICMP message types handled by icmp_unreach().
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MCA support has been removed but this dependency escaped removal.
Also, there is a duplicate PPC_PSERIES dependency that appeared
when the ethernet drivers were separated into vendor/model
specific directories, so we remove that here as well.
Reported-by: Robert de Rooy <robert.de.rooy@gmail.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 13d82bf5 (ipv4: Fix flushing of cached routing informations)
added the support to flush learned pmtu information.

However, using rt_genid is quite heavy as it is bumped on route
add/change and multicast events amongst other places. These can
happen quite often, especially if using dynamic routing protocols.

While this is ok with routes (as they are just recreated locally),
the pmtu information is learned from remote systems and the icmp
notification can come with long delays. It is worthy to have separate
genid to avoid excessive pmtu resets.

Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tunnel devices call update_pmtu for each packet sent, this causes
contention on the fnhe_lock. Ignore the pmtu update if pmtu is not
actually changed, and there is still plenty of time before the entry
expires.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 05ab86c5 (xfrm4: Invalidate all ipv4 routes on
IPsec pmtu events). Flushing all cached entries is not needed.

Instead, invalidate only the related next hop dsts to recheck for
the added next hop exception where needed. This also fixes a subtle
race due to bumping generation id's before updating the pmtu.

Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

If PCIe supports PM capabilities, bnx2x will always claim eeprom is accessible
as PCI_D0 is zero.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch includes a few changes that change the driver's flow without truly
changing anything in its functionality - use usleep_range for short sleeps
instead of msleep and initialize Tx consumer during initialization for better
information during errors.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch revises many bnx2x prints - mainly fixing print typos and
adding some new debug prints (mostly for parity issues).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch introduces several small  changes to the driver, none which actually
change any flow:
 1. Removes prototypes of unexisting functions and unused defines.
 2. Fixes alignment and spacing issues.
 3. Changes numeric usage into constants.
 4. Remove unnecessary parenthesis.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch correct various typos, fix comments conventions and
adds/removes a few comments.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch removes unnecessary blank lines and adds a few where such are needed
(between variable declarations and code)
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The bnx2x_select_queue() was using __skb_tx_hash() to select the
transmit queue, totally ignoring XPS settings, while XPS can help
performance quite significantly, so change the bnx2x_select_queue()
to use __dev_pick_tx() instead which will use XPS if configured.

Based on patches from Ying Cai and Havard Skinnemoen
Reported-by: govindarajulu.v <govindarajulu90@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Havard Skinnemoen <hskinnemoen@google.com>
Cc: Ying Cai <ycai@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Forcing uninitialized state allows us to upgrade and reinitialize the adapter.

FW_VERSION_T4 = 1.4.0.0
FW_VERSION_T5 = 0.0.0.0
At this point driver supports above and greater than above version of firmware.
If it doesn't find the required firmware version than it forces the adapter to
be reinitialized as shown below.

1) If FW_ON_ADAPTER < FW_VERSION and we're the MASTER_PF force uninitialized
   state and a FW upgrade if available.

       - If FW_ON_ADAPTER < /lib/firmware/cxgb4/t*fw.bin we will update the
         adapters FW.
       - If FW_ON_ADAPTER >= /lib/firmware/cxgb4/t*fw.bin don't upgrade FW.
       - If upgrade_fw() fails force reinitialization of the adapter anyways,
         it might still work.

   Either way forcing the uninitialized state allows cxgb4 reinitialize FW.

2) If FW_ON_ADAPTER >= FW_VERSION driver follows normal path.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added code to initiate FW dump via ethtool. Driver checks if the previous dump
has been cleared before initiating the dump. It doesn't initiate the dump
if it is not cleared.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Additional 4 bytes found in the skb is the CRC calculated by the
CPDMA hardware, check the CRC bit in CPDMA status field of
Descriptor and remove the CRC length from the skb. This extra
4 byte can be seen when capturing packets using tcpdump.
This has been tested in TI816x platform.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Hackberry has a PHY that needs to be powered up through a GPIO, so
we need to use a fixed regulator here.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The EMAC only has one pinset available for muxing, so hopefully, we
cover all cases.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a separate driver for the MDIO interface of the
Allwinner ethernet controllers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Allwinner A10 has an ethernet controller that seem to be developped
internally by them.

The exact feature set of this controller is unknown, since there is no
public documentation for this IP, and this driver is mostly the one
published by Allwinner that has been heavily cleaned up.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PHY library currently does not know about the the reverse MII
connection type. Add it to the list of supported PHY modes and update
of_get_phy_mode() to support it and look for the string "rev-mii".
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the support of IPv4 over Ipv4 for the module sit. The gain of
this feature is to be able to have 4in4 and 6in4 over the same interface
instead of having one interface for 6in4 and another for 4in4 even if
encapsulation addresses are the same.

To avoid conflicting with ipip module, sit IPv4 over IPv4 protocol is
registered with a smaller priority.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Before this patch, ip_tunnel_xmit() was using the field protocol from the IP
header passed into argument.
There is no functional change, this patch prepares the support of IPv4 over
IPv4 for module sit.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 1a37e412 (net: Use 16bits for *_headers
fields of struct skbuff) converts skb->*_header to u16,
some #if NET_SKBUFF_DATA_USES_OFFSET are now useless,
and to be safe, we could just use "X = (typeof(X)) ~0U;"
as suggested by David.

Cc: David S. Miller <davem@davemloft.net>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This corrects an regression introduced by "net: Use 16bits for *_headers
fields of struct skbuff" when NET_SKBUFF_DATA_USES_OFFSET is not set. In
that case skb->tail will be a pointer whereas skb->network_header
will be an offset from head. This is corrected by using wrappers that
ensure that calculations are always made using pointers.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

GRO on IPv4 doesn't aggregate frames if they don't have DF bit set.

Some servers use IP_MTU_DISCOVER/IP_PMTUDISC_PROBE, so linux receivers
are unable to aggregate this kind of traffic.

The right thing to do is to allow aggregation as long as the DF bit has
same value on all segments.

bnx2x LRO does this correctly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current state of affairs is that read()/write() will setup
RFS (Receive Flow Steering) for internet protocol sockets while
poll()/epoll() does not.

When poll() gets called with a TCP or UDP socket, we should update
the flow target.

This permits to RFS (if enabled) to select the appropriate CPU for
following incoming packets.

Note: Only connected UDP sockets can benefit from RFS.
Signed-off-by: David Majnemer <majnemer@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Paul Turner <pjt@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Corrects an byte order conflict introduced by "sctp: Correct access to
skb->{network, transport}_header". All the values in question are host
byte order.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

pci_enable_device() will set device power state to D0,
so it's no need to do it again in tulip_init_one().
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>