Since it's a pin control, GPIO counterpart needs to know the mapping
between pin numbering and GPIO numbering. Enable this by calling
gpiochip_add_pin_range() at the chip addition time.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-7-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The npins field is assigned twice. Remove the first occurrence.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-6-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The Cypress GPIO expander is an I²C discrete component. Hence
the platform may contain more than one of a such. Currently
this has limitations in the driver due to same name used for
all chips of a type. Replace this with device instance specific
name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-5-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

It's an obvious typo in never tested piece of code that
successful detection shouldn't fail. Fix that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-4-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

No need to assign first line number for IRQ chip.
Let IRQ core to decide.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-2-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Since recently, the kernel is nagging about mutable irq_chips:

   "not an immutable chip, please consider fixing it!"

Drop the unneeded copy, flag it as IRQCHIP_IMMUTABLE, add the new
helper functions and call the appropriate gpiolib functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Link: https://lore.kernel.org/r/20220902182650.83098-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix spelling typo in comment.
Reported-by: k2ci <kernel-bot@kylinos.cn>
Signed-off-by: Jiangshan Yi <yijiangshan@kylinos.cn>
Link: https://lore.kernel.org/r/20220905071300.1832105-1-13667453960@163.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIO library now accepts fwnode as a firmware node, so
switch the driver to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220831135512.78407-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Use dev_dbg() instead of printk(KERN_DEBUG) to avoid the following
checkpatch.pl warning:
"Prefer [subsystem eg: netdev]_dbg([subsystem]dev, ... then
dev_dbg(dev, ... then pr_debug(...  to printk(KERN_DEBUG ...".
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220831135636.3176406-4-claudiu.beznea@microchip.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Move gpio suspend/resume execution local to driver and let it execute as
close as possible to the moment the machine specific PM code is executed
(by setting it to .noirq member of dev_pm_ops). With this the
at91_pinctrl_gpio_suspend()/at91_pinctrl_gpio_resume() calls were removed
from arch/arm/mach-at91/pm.c and also a header has been removed.
The patch has been checked on sama5d3_xplained, sam9x60ek,
sama5d2_xplained, sama7g5ek boards.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220831135636.3176406-3-claudiu.beznea@microchip.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Use kernel-doc style for documentation of struct at91_gpio_chip.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220831135636.3176406-2-claudiu.beznea@microchip.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The GPIO library code will assign default value for number of OF
cells, no need to repeat this in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220830175850.44770-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge tag 'renesas-pinctrl-for-v6.1-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: renesas: Updates for v6.1

  - Document pin control support for the RZ/Five SoC.

Change PINCTRL_IMX8M* dependency from just ARCH_MXC to SOC_IMX8M,
likewise is done for other PINCTRL_IMX* kconfig. This avoid polluting
the config when SOC_IMX8M is not enabled.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20220830142727.313080-1-francesco.dolcini@toradex.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Use dev_dbg instead of dev_warn for additional support of pinmux
feature.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Link: https://lore.kernel.org/r/20220830110525.1933198-1-Basavaraj.Natikar@amd.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

When the driver want to disable the signal of the function, it doesn't
need to query the state of the mux function's signal on a pin. The
condition below will miss the disable of the signal:
Ball | Default | P0 Signal | P0 Expression               | Other
-----+---------+-----------+-----------------------------+----------
 E21   GPIOG0    SD2CLK      SCU4B4[16]=1 & SCU450[1]=1    GPIOG0
-----+---------+-----------+-----------------------------+----------
 B22   GPIOG1    SD2CMD      SCU4B4[17]=1 & SCU450[1]=1    GPIOG1
-----+---------+-----------+-----------------------------+----------
Assume the register status like below:
SCU4B4[16] == 1 & SCU4B4[17] == 1 & SCU450[1]==1
After the driver set the Ball E21 to the GPIOG0:
SCU4B4[16] == 0 & SCU4B4[17] == 1 & SCU450[1]==0
When the driver want to set the Ball B22 to the GPIOG1, the condition of
the SD2CMD will be false causing SCU4B4[17] not to be cleared.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20220818101839.28860-1-billy_tsai@aspeedtech.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

'unsigned int' should be clearer than 'unsigned'.
Signed-off-by: Jilin Yuan <yuanjilin@cdjrlc.com>
Link: https://lore.kernel.org/r/20220825124134.30242-1-yuanjilin@cdjrlc.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

In order to ensure only documented properties are present, node schemas
must have unevaluatedProperties or additionalProperties set to false
(typically).
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220823145649.3118479-6-robh@kernel.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Feedback from Kent had showed some better selections for symbols to
use for pinctrl-amd debugfs output.  Adopt some of those instead.

Fixes: e8129a07 ("pinctrl: amd: Use unicode for debugfs output")
Suggested-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Link: https://lore.kernel.org/r/20220823230753.14799-1-mario.limonciello@amd.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Fix up the build.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Link: https://lore.kernel.org/r/20220826152650.2c55e482@canb.auug.org.auSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Merge branch 'i2c/make_remove_callback_void-immutable' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux into devel

This branch is needed to make the i2c driver remove() callback in new
driver compile properly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The mt8186 contains 8 GPIO physical address bases that correspond to
the 'reg-names' of the pinctrl driver. The 'reg-names' entries in
bindings are ordered incorrectly, though. The system crashes due of an
erroneous address when the regulator initializes.

We fix the 'reg-names' for the pinctrl nodes and the pinctrl-mt8186
example in bindings.

Fixes: 338e953f ("dt-bindings: pinctrl: mt8186: add pinctrl file and binding document")
Co-developed-by: Guodong Liu <guodong.liu@mediatek.com>
Signed-off-by: Guodong Liu <guodong.liu@mediatek.com>
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220819120649.21523-1-allen-kh.cheng@mediatek.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Add pinctrl driver support for MediaTek SoC mt8188.
Signed-off-by: Hui.Liu <hui.liu@mediatek.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220818075012.20880-3-hui.liu@mediatek.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Add the pinctrl header file on MediaTek mt8188.
Add the new binding document for pinctrl on MediaTek mt8188.
Signed-off-by: Hui.Liu <hui.liu@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220818075012.20880-2-hui.liu@mediatek.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Add pinctrl driver to support pin configuration for LPASS
(Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SC8280XP.

This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.

Hardware setup looks like:

    TLMM GPIO[189 - 207] --> LPASS LPI GPIO [0 - 18]

This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220817113747.9111-3-srinivas.kandagatla@linaro.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Add device tree binding Documentation details for Qualcomm SC8280XP
LPASS(Low Power Audio Sub System) LPI(Low Power Island) pinctrl driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220817113747.9111-2-srinivas.kandagatla@linaro.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Add pinctrl driver to support pin configuration for LPASS
(Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SM8450.

This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.

Hardware setup looks like:

    TLMM GPIO[165 - 187] --> LPASS LPI GPIO [0 - 22]

This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220817113833.9625-3-srinivas.kandagatla@linaro.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Add device tree binding Documentation details for Qualcomm SM8450
LPASS(Low Power Audio Sub System) LPI(Low Power Island) pinctrl driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220817113833.9625-2-srinivas.kandagatla@linaro.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The pin control header provides struct pingroup and PINCTRL_PINGROUP() macro.
Utilize them instead of open coded variants in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220621112904.65674-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The pin control header provides struct pingroup and PINCTRL_PINGROUP() macro.
Utilize them instead of open coded variants in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220620165053.74170-1-andriy.shevchenko@linux.intel.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Add support for cypress I2C GPIO expanders cy8c9520, cy8c9540 and
cy8c9560. The GPIO expanders feature a PWM mode, thus add it as
pinctrl driver.

The chip features multiple drive modes for each pin when configured
as output and multiple bias settings when configured as input.

Tested all three components and verified that all functionality
is fully working.

Datasheet: https://www.cypress.com/file/37971/downloadSigned-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Naresh Solanki <naresh.solanki@9elements.com>
Link: https://lore.kernel.org/r/20220816054917.7893-3-patrick.rudolph@9elements.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Added device tree binding documentation for
Cypress CY8C95x0 I2C pin-controller.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220816054917.7893-2-patrick.rudolph@9elements.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The aspeed pinctrl parent node (SCU) in the examples is missing various
properties. Add the properties in preparation for the SCU schema.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20220810161635.73936-2-robh@kernel.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Macro PIN_GRP() is not used, remove it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805122202.23174-4-pali@kernel.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Now when all MPP pins are properly defined and every MPP pin has GPIO
function, always checks for errors in armada_37xx_gpio_request_enable()
function when calling armada_37xx_pmx_set_by_name(). Function
armada_37xx_pmx_set_by_name() should not return "not supported" error
anymore for any GPIO pin when requesting GPIO mode.

Fixes: 87466ccd ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20220805122202.23174-3-pali@kernel.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

All 3 MPP pins (20, 21 and 22) can be configured individually and also can
be configured to GPIO functions. Fix definitions for these MPP pins in
existing pin groups. After this change GPIO function can be enabled just
for one of these 3 pins.

Fixes: 87466ccd ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805122202.23174-2-pali@kernel.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

gpio1_5 and gpio2_2 are GPIO-only pins. Add them into MPP groups table
so they are properly exported as valid pin numbers.

Fixes: 87466ccd ("pinctrl: armada-37xx: Add pin controller support for Armada 37xx")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220805122202.23174-1-pali@kernel.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

RV1126 has five GPIOs groups - GPIO0 in PD_MMU and GPIO1-4
in PD_BUS.

In GPIO0, up to Lower C group GPIO0_C[3:0] is part of PMU
but rest of the groups from there are part of GRF.

Added pinctrl support for RV1126 and the pull, drv and schmitt
calculations are inferred from [1] authored by Jianqun Xu.

[1] https://github.com/rockchip-linux/kernel/blob/develop-4.19/drivers/pinctrl/pinctrl-rockchip.c

Cc: linux-gpio@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Sugar Zhang <sugar.zhang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20220818124132.125304-8-jagan@edgeble.aiSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Document dt-bindings for RV1126 SoC pinctrl support.

Cc: linux-gpio@vger.kernel.org
Cc: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Link: https://lore.kernel.org/r/20220818124132.125304-7-jagan@edgeble.aiSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)

So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>