The delay cells of some SoCs may have less delay per one cell,
for such SoCs, user could set the start delay cell point to bypass
the first a few meaningless tuning commands.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Disable DLL delay line settings explicitly during driver initialization
in case ROM/uBoot had set an invalid delay.
e.g. MX6DL ROM has set the default delay line(DLLCTRL) to 0x1000021,
the uSDHC clock timing will become marginal when works on DDR mode
due to default delay and will possibly see CRC errors in case the board
is not perfectly designed on the eMMC chip layout.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Currently, we config the watermark_level register only in probe.
This will cause the mmc write operation timeout issue after system
resume back in LPSR mode. Because in LPSR mode, after system resume
back, the watermark_level register(0x44) changes to 0x08000880, which
set the write watermark level as 0, and set the read watermark level
as 128. This value is incorrect.

This patch restores the setting of watermark level register after
system resume back.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It will be used for platform specific suspend/resume state save/restore
work for some low power mode like Mega/Fast or LPSR mode.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The driver has already implemented the private .set_timeout()
callback for common SDHCI code to do correct timeout value setting,
it does not need call sdhci_calc_timeout(), so this quirk actually
is not working. Remove it now.
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Switch to use the more robust common mmc_regulator_set_vqmmc()
function in MMC core which set the target voltage as close as
possible to target voltage.

We did not re-factor the whole sdhci_start_signal_voltage_switch()
cause we want to keep the original signal switch order between host
and card to avoid potential break.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Export DSR register through sysfs same as we did for the CID, CSD and
OCR registers.
Signed-off-by: Bojan Prtvar <prtvar.b@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In dw_mmc.c, it's enabled by default.
It doesn't need to set MMC_CAP_ERASE in rockchip anymore.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This flag needs to use the trim/discard/erase commands.
dwmmc controller enables this flag by default.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The reason for why we expose these to dt is that some of
the controller is unable to send special cmd type due to
the hw limitation.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds description for no-sd, no-sdio, no-mmc. We expose
these to DT as some of the controllers are unable to deal with
special cmd type due to hw limitation.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Registers CID and CSD are already exported through sysfs so let's make
this interface complete by adding missing OCR register.
Signed-off-by: Bojan Prtvar <prtvar.b@gmail.com>
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The capabilities in iproc platform data are magic numbers. So
replace them with the proper capability defines to make it
readable.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds the missing define for the suspend/resume
capability (according to SD Host Controller spec).
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Host drivers which needs to valdiate for non-supported MMC
commands and returnn error code for such requests.

To improve and simplify the behaviour, let's invent MMC_CAP2_NO_MMC
which these host drivers can set to tell the mmc core to skip sending MMC
commands during card initialization.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The driver registered for CPU frequency transitions to recalculate its
clock when ARM clock frequency changes (ratio between frequencies of
ARM's parent clock (fclk) and clock for peripherals remains fixed).

This is needed only on S3C24xx platform when cpufreq driver is enabled
so limit the ifdef to respective cpufreq Kconfig.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

sdhci_send_command() starts a timer to catch cases where the host
controller fails. The timer is normally deleted when the request completes,
but in the case of sdhci_execute_tuning() the request is handled
differently and the timer is left running. This goes unnoticed because
tuning is done before another command so the timer gets reset then.
That should not be relied upon, so make sdhci_execute_tuning() delete the
timer.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The STOP command is sent in error conditions, even when the command is
not finished. Avoid triggering the warning for that in sdhci_send_command()
by setting host->cmd to NULL first.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In order to support commands during data transfer, it will be possible to
need to reset the command circuit while the data circuit is in use, and
vice versa. It is now easy to determine whether the command or data circuit
is in use, and so just skip the corresponding reset if it is.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Factor out sdhci_auto_cmd12() so that there is a single place that controls
whether auto-CMD12 is used.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In order to support commands during data transfer, there will have to be up
to two active requests (mrqs) at a time, instead of just one. That means
recording which request is finished.  Doing that obsoletes host->mrq which
is therefore removed.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In order to support commands during data transfer, there will have to be up
to two active requests (mrqs) at a time, instead of just one. Provide two
timers instead of just one. One of the timers is for requests that do not
use the data lines, and the other one is for requests that do.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Factor out sdhci_data_line_cmd() to improve readability and because it is
used in multiple places.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In order to support commands during data transfer, there will have to be up
to two active requests (mrqs) at a time, instead of just one. That means
ensuring that all requests get errored out in the cases of card or driver
removal.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Several pointers are used to identify when interrupts are expected. Namely,
host->cmd, host->data_cmd and host->data. Ensure those are cleared when
a request finishes. That tidies the case when a request is errored out
before normal processing has completed, ensuring any interrupts that occur
subsequently are not acted upon.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

SDHCI recovers from errors by resetting the cmd and data circuits. Until
that is done, there very well might be more interrupts, so ignore them in
that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Factor out sdhci_needs_reset() so it can be reused.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In order to support commands during data transfer, there will have to be up
to two active requests (mrqs) at a time, instead of just one. That means
the driver must identify which one to finish. Prepare for that by factoring
out sdhci_finish_mrq().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In order to support commands during data transfer, it will be possible
that host->data is not NULL when preparing a new request. Move a warning
that assumes otherwise.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In order to support commands during data transfer, there will have to be up
to two active requests (mrqs) at a time, instead of just one. That means
host->mrq will not be able to be used.

In several places, host->mrq is used when instead the mrq can be determined
from the cmd or data pointers. Reduce the use of host->mrq by doing that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Now that there is host->data_cmd to record the command for which a data
interrupt is expected, it is possible to determine whether a command with
busy signaling has completed without an extra flag. So host->busy_handle
is not needed. Remove it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In order to support commands during data transfer, there must be a
distinction between the command that is using the command line (and
for which a command interrupt is expected) and the command that is
using the data lines (for which a data interrupt is expected).

There is host->cmd for the command line, but there is only host->data
for the data lines, which is a different structure, does not represent
the command in use, and is anyway NULL in the case of commands that use
the data lines for busy signalling instead of data transfer.

Introduce host->data_cmd to record what command is using the data lines,
and use that instead of host->cmd when referring to the data command.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

sdhci_finish_command() is going to set host->cmd to NULL. Simplify the
code by using a local variable to hold host->cmd and set host->cmd to
NULL at the start.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

BUG is never the right thing for SDHCI to do. Get rid of BUG_ON in cases it
will oops anyway if the pointer is NULL, or if the condition is logically
impossible.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In order to support commands during data transfer, command and data
handling needs to be untangled.

That means sdhci_finish_cmd() must not be called from the data IRQ
handler. It is being called because of busy signal handling, which
is treating the command as not finished until the busy signal is
released.

Instead, move busy signal handling from sdhci_cmd_irq() into
sdhci_finish_cmd(). Then the data IRQ handler does not need to call
sdhci_finish_cmd() and can instead finish the request.

What this means in practice for a command with busy signaling, is that
the command response is read from the host controller when the command
complete interrupt is received, thus freeing up the command circuit for
other commands.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

At the successful conclusion of sdhci_pci_probe(), if runtime pm was
allowed, the device would be runtime suspended.  That wastes a lot of time
during initialization.  Instead leave the device active until the mmc core
scans for a card.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add sdhci_read_caps() and __sdhci_read_caps() to make it easier for drivers
to fix the version and capabilities registers.

Pedantically, the SDHCI specification states that the capabilities
registers are valid when the host controller resets the Software Reset For
All bit. That requirement has always been satisfied by performing a reset
at the start of initialization, and consequently that is now part of the
new functions.

Although the SDHCI_QUIRK_MISSING_CAPS quirk has not yet been removed,
drivers that want to provide their own caps can now use these functions
instead of that quirk.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

In preparation for adding a function to read the capability registers.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Signal voltage support is not a quirk, it is a capability. According to the
SDHCI specification, support for 1.8V signaling is determined by the
presence of one of the capability bits SDHCI_SUPPORT_SDR50,
SDHCI_SUPPORT_SDR104, or SDHCI_SUPPORT_DDR50. This is complicated by also
supporting eMMC which has 1.8V modes and 1.2V modes. It would be possible
to use the transfer mode to determine signal voltage support, except for
eMMC DDR52 mode which uses the same capability (MMC_CAP_1_8V_DDR) for 1.8V
signaling and 3V signaling.

In addition, the mmc core will fail over from one signaling voltage to the
next (refer mmc_power_up()) which means SDHCI really needs to validate
which voltages are actually supported.

Introduce SDHCI flags for signal voltage support and set them based on the
supported transfer modes. In general, drivers should prefer to set the
supported transfer modes correctly rather than change the signal voltage
capability, except in the case where 3V DDR52 is supported but 1.8V is
not.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>