- 15 Jun, 2023 29 commits
-
-
Jiasheng Jiang authored
Add the missing check for platform_get_resource and return error if it fails. Fixes: 4b45efe8 ("mfd: Add support for Intel Sunrisepoint LPSS devices") Signed-off-by:
Jiasheng Jiang <jiasheng@iscas.ac.cn> Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://lore.kernel.org/r/20230609014818.28475-1-jiasheng@iscas.ac.cn
-
Sean Nyekjaer authored
Use devm_register_sys_off_handler() that allows to register multiple power-off handlers. This will allow boards using the stpmic1 to power-off. Signed-off-by:
Sean Nyekjaer <sean@geanix.com> Signed-off-by:
-
Sean Nyekjaer authored
Fixup main control register and bits naming so the match the naming from the datasheet. https://www.st.com/resource/en/datasheet/stpmic1.pdfSigned-off-by:
-
Vignesh Viswanathan authored
Document the qcom,tcsr-ipq8074 compatible. Signed-off-by:
Vignesh Viswanathan <quic_viswanat@quicinc.com> Acked-by:
Conor Dooley <conor.dooley@microchip.com> Signed-off-by:
-
Jerome Neanne authored
Use new API for power-off mode support: Link: https://lwn.net/Articles/894511/ Link: https://lore.kernel.org/all/7hfseqa7l0.fsf@baylibre.com/ sys-off API allows support of shutdown handler and restart handler. Shutdown was not supported before that enhancement. This is required for platform that are not using PSCI. Test: - restart: # reboot Default is cold reset: # cat /sys/kernel/reboot/mode Switch boot mode to warm reset: # echo warm > /sys/kernel/reboot/mode - power-off: # halt Tested on AM62-LP-SK board. Signed-off-by:
Jerome Neanne <jneanne@baylibre.com> Suggested-by:
Andrew Davis <afd@ti.com> Reviewed-by:
-
Johan Hovold authored
Prior to commit af503716 ("i2c: core: report OF style module alias for devices registered via OF") drivers using OF matching needed an i2c module alias such as "i2c:pm8008" for module autoloading to work. Drop the bogus i2c alias from the pm8008 driver which was merged long after i2c core was fixed and whose alias did not match the driver name ("pm8008") to begin with. Signed-off-by:
Johan Hovold <johan+linaro@kernel.org> Signed-off-by:
-
Johan Hovold authored
Add the missing module device table alias to that the driver can be autoloaded when built as a module. Cc: stable@vger.kernel.org # 5.14 Fixes: 6b149f33 ("mfd: pm8008: Add driver for QCOM PM8008 PMIC") Signed-off-by:
Konrad Dybcio <konrad.dybcio@linaro.org> Signed-off-by:
-
Jerome Neanne authored
TPS65219 PMIC GPIOs are exposed in a standard way: gpiodetect gpiochip0 [tps65219-gpio] (3 lines) tps65219-gpios is incorrect cell name (plural). Changed to tps65219-gpio (singular) Co-developed-by:
Jonathan Cormier <jcormier@criticallink.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Julien Panis authored
TPS6594 is a Power Management IC which provides regulators and others features like GPIOs, RTC, watchdog, ESMs (Error Signal Monitor), and PFSM (Pre-configurable Finite State Machine) managing the state of the device. TPS6594 is the super-set device while TPS6593 and LP8764 are derivatives. Signed-off-by:
Julien Panis <jpanis@baylibre.com> Reviewed-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Reviewed-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Dan Carpenter authored
These error paths accidentally return success when they should return -EINVAL. Fixes: 325bec71 ("mfd: tps6594: Add driver for TI TPS6594 PMIC") Signed-off-by:
Dan Carpenter <dan.carpenter@linaro.org> Link: https://lore.kernel.org/r/49f7cd8f-f7eb-40f1-91e8-291620c684df@kili.mountainSigned-off-by:
-
Pascal Paillet authored
Add vref_ddr supply description for the STPMIC1. Signed-off-by:
Pascal Paillet <p.paillet@foss.st.com> Acked-by:
-
Christophe JAILLET authored
Use dev_err_probe() to simplify code, save a few LoC and be consistent with error codes handling in messages. It also filters -EPROBE_DEFER that can be returned by devm_clk_get(). Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/73fdc6ecf619f80fad126abca11fb579d3d87f64.1684565021.git.christophe.jaillet@wanadoo.frSigned-off-by:
-
Christophe JAILLET authored
If devm_gpiod_get_optional() fails, some resources need to be released, as already done in the .remove() function. While at it, remove the unneeded error code from a dev_err_probe() call. It is already added in a human readable way by dev_err_probe() itself. Fixes: 6a0ee2a6 ("mfd: wcd934x: Replace legacy gpio interface for gpiod") Signed-off-by:
-
Dario Binacchi authored
Add binding definition for CAN3 peripheral. Signed-off-by:
Dario Binacchi <dario.binacchi@amarulasolutions.com> Link: https://lore.kernel.org/r/20230423172528.1398158-2-dario.binacchi@amarulasolutions.comSigned-off-by:
-
Arnd Bergmann authored
When CONFIG_PM is disabled, the prototypes for these two functions are not visible: drivers/mfd/intel-lpss.c:482:5: error: no previous prototype for 'intel_lpss_suspend' [-Werror=missing-prototypes] 482 | int intel_lpss_suspend(struct device *dev) | ^~~~~~~~~~~~~~~~~~ drivers/mfd/intel-lpss.c:503:5: error: no previous prototype for 'intel_lpss_resume' [-Werror=missing-prototypes] 503 | int intel_lpss_resume(struct device *dev) Add the same #ifdef around the definition of the unused functions, which avoids the warning and slightly reduces the code size. Signed-off-by:Arnd Bergmann <arnd@arndb.de> Link: https://lore.kernel.org/r/20230516202746.561111-1-arnd@kernel.orgSigned-off-by:
-
Aidan MacDonald authored
The AXP192 PMIC is similar to the AXP202/AXP209, but with different regulators, additional GPIOs, and a different IRQ register layout, so it needs a new compatible string. Signed-off-by:
Aidan MacDonald <aidanmacdonald.0x0@gmail.com> Acked-by:
-
Aidan MacDonald authored
The AXP192 PMIC is similar to the AXP202/AXP209, but with different regulators, additional GPIOs, and a different IRQ register layout. Signed-off-by:
-
Lee Jones authored
Prevent mails from being sent to old and unmonitored inboxes. Signed-off-by: -
Abel Vesa authored
The phy pattern property will be used for providing eUSB2 repeater functionality. This will be modelled as a Qualcomm PHY driver. Signed-off-by:
Abel Vesa <abel.vesa@linaro.org> Reviewed-by:
-
Uwe Kleine-König authored
After commit b8a1a4cd ("i2c: Provide a temporary .probe_new() call-back type"), all drivers being converted to .probe_new() and then 03c835f4 ("i2c: Switch .probe() to not take an id parameter") convert back to (the new) .probe() to be able to eventually drop .probe_new() from struct i2c_driver. Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20230515182752.10050-1-u.kleine-koenig@pengutronix.deSigned-off-by:
-
Guiting Shen authored
the i2c_set_clientdata() is the inline function which is complemented by the dev_set_drvdata() internally. Do not need to use i2c_set_clientdata() and dev_set_drvdata() at the same time. Signed-off-by:
Guiting Shen <aarongt.shen@gmail.com> Reviewed-by:
Johan Hovold <johan@kernel.org> Reviewed-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by:
-
Christophe JAILLET authored
This driver does not use i2c, so there is no point in including <linux/i2c.h> Remove it. Signed-off-by:
-
Christophe JAILLET authored
This driver does not use i2c, so there is no point in including <linux/i2c.h> Remove it and add the needed <linux/device.h> instead, which is much more lightweight. Signed-off-by:
-
Mark Brown authored
regmap has introduced a maple tree based register cache which makes use of this more advanced data structure which has been added to the kernel recently. Maple trees are much flatter than rbtrees, meaning that they do not grow to such depths when the register map is sparse which makes access a bit more efficient. The maple tree cache type is still a bit of a work in progress but should be effective for some devices already. The wm831x devices have a pretty sparse register map and being always on devices never do cache syncs so don't hit the major current disadvantage so they should be good candiates for using the maple tree cache. Update to do so, there should be little if any visible difference at runtime. Signed-off-by:
Mark Brown <broonie@kernel.org> Reviewed-by:
-
Ilpo Järvinen authored
On some MAX 10 cards, the BMC firmware is not available to service handshake registers during secure update erase and write phases at normal speeds. This problem affects at least hwmon driver. When the MAX 10 hwmon driver tries to read the sensor values during a secure update, the reads are slowed down (e.g., reading all D5005 sensors takes ~24s which is magnitudes worse than the normal <0.02s). Manage access to the handshake registers using a rw semaphore and a FW state variable to prevent accesses during those secure update phases and return -EBUSY instead. If handshake_sys_reg_nranges == 0, don't update bwcfw_state as it is not used. This avoids the locking cost. Co-developed-by:
Russ Weight <russell.h.weight@intel.com> Signed-off-by:
Xu Yilun <yilun.xu@intel.com> Signed-off-by:
Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Signed-off-by:
-
Ilpo Järvinen authored
Move m10bmc_sys_read() out from the header to prepare it for adding more code into the function which would make it too large to be a static inline any more. While at it, replace the vague wording in function comment with more precise statements. Reviewed-by:
-
Ilpo Järvinen authored
Wrap regmap_update_bits() with m10bmc_sys_update_bits() in order to be able to add additional checks into it. Co-developed-by:
-
Ilpo Järvinen authored
Create INTEL_M10_BMC_CORE namespace for symbols exported by intel-m10-bmc-core. Reviewed-by:
-
Lee Jones authored
Merge branches 'tb-mfd-clk-input-pinctrl-power-rtc-sound-6.5', 'ib-mfd-tps6594-core-6.5', 'ib-mfd-regulator-max5970-6.5', 'ib-mfd-regulator-6.5' and 'ib-mfd-power-6.5' into ibs-for-mfd-merged
-
- 12 Jun, 2023 1 commit
-
-
Mark Brown authored
The twl6040 is only capable of performing single register read and write operations which means it gains no advantage from using a rbtree register cache, convert it to using the more modern maple tree register cache instead. This should be more efficient. Signed-off-by:
-
- 08 Jun, 2023 9 commits
-
-
Jakob Hauser authored
Add device tree binding documentation for rt5033 multifunction device, voltage regulator and battery charger. Signed-off-by:
Jakob Hauser <jahau@rocketmail.com> Reviewed-by:
-
Jakob Hauser authored
Additionally to the already available ref "power-supply.yaml", replace "additionalProperties: false" by "unevaluatedProperties: false". Otherwise, when referencing rt5033-battery in an example, message "'power-supplies' does not match any of the regexes: 'pinctrl-[0-9]+'" will be returned. Signed-off-by:
Sebastian Reichel <sebastian.reichel@collabora.com> Signed-off-by:
-
Jakob Hauser authored
The rt5033-battery fuelgauge can't get a status by itself. The rt5033-charger can, let's get this value. To get the charger as a "supplier" from the devicetree, the "of_node" needs to be initiated. Additionally, in the probe function replace dev_err() with dev_err_probe(), this will avoid printing an error for -EPROBE_DEFER when the battery driver probes before the charger driver. Signed-off-by:
-
Jakob Hauser authored
Move struct rt5033_battery from the mfd header into the battery driver because it's not used by others. Within struct rt5033_battery, remove the line "struct rt5033_dev *rt5033;" because it doesn't get used. In rt5033.h, remove #include <linux/power_supply.h>, it's not necessary anymore. In rt5033_battery.c, remove #include <linux/mfd/rt5033.h>, it's not necessary anymore either. Instead add #include <linux/regmap.h> and Signed-off-by:
-
Jakob Hauser authored
This patch adds device driver of Richtek RT5033 PMIC. The driver supports switching charger. rt5033 charger provides three charging modes. The charging modes are pre-charge mode, fast charge mode and constant voltage mode. They vary in charge rate, the charge parameters can be controlled by i2c interface. Tested-by:
Raymond Hackley <raymondhackley@protonmail.com> Signed-off-by:
-
Jakob Hauser authored
Order the register blocks to have the masks in descending manner. Add new defines for constant voltage shift (RT5033_CHGCTRL2_CV_SHIFT), MIVR mask (RT5033_CHGCTRL4_MIVR_MASK), pre-charge current shift (RT5033_CHGCTRL4_IPREC_SHIFT), internal timer disable (RT5033_INT_TIMER_DISABLE), termination disable (RT5033_TE_DISABLE), CFO disable (RT5033_CFO_DISABLE), UUG disable (RT5033_CHARGER_UUG_DISABLE). The fast charge timer type needs to be written on mask 0x38 (RT5033_CHGCTRL3_TIMER_MASK). To avoid a bit shift on application, change the values of the timer types to fit the mask. Added the timout duration as a comment. And the timer between TIMER8 and TIMER12 is most likely TIMER10, see e.g. RT5036 [1] page 28 bottom. Add value options for MIVR (Minimum Input Voltage Regulation). Move RT5033_TE_ENABLE_MASK to the block "RT5033 CHGCTRL1 register", in order to have the masks of the register collected there. To fit the naming scheme, rename it to RT5033_CHGCTRL1_TE_EN_MASK. Move RT5033_CHG_MAX_CURRENT to the block "RT5033 charger fast-charge current". Add new defines RT5033_CV_MAX_VOLTAGE and RT5033_CHG_MAX_PRE_CURRENT to the blocks "RT5033 charger constant charge voltage" and "RT5033 charger pre-charge current limits". In include/linux/mfd/rt5033.h, turn power_supply "psy" into a pointer in order to use it in devm_power_supply_register(). [1] https://media.digikey.com/pdf/Data%20Sheets/Richtek%20PDF/RT5036%20%20Preliminary.pdfSigned-off-by:
-
Jakob Hauser authored
The charger state mask RT5033_CHG_STAT_MASK should be 0x30 [1][2]. The high impedance mask RT5033_RT_HZ_MASK is actually value 0x02 [3] and is assosiated to the RT5033 CHGCTRL1 register [4]. Accordingly also change RT5033_CHARGER_HZ_ENABLE to 0x02 to avoid the need of a bit shift upon application. For input current limiting AICR mode, the define for the 1000 mA step was missing [5]. Additionally add the define for DISABLE option. Concerning the mask, remove RT5033_AICR_MODE_MASK because there is already RT5033_CHGCTRL1_IAICR_MASK further up. They are redundant and the upper one makes more sense to have the masks of a register colleted there as an overview. [1] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/drivers/battery/rt5033_charger.c#L669-L682 [2] https://github.com/torvalds/linux/blob/v6.0/include/linux/mfd/rt5033-private.h#L59-L62 [3] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/include/linux/battery/charger/rt5033_charger.h#L44 [4] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/drivers/battery/rt5033_charger.c#L223 [5] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/drivers/battery/rt5033_charger.c#L278Signed-off-by:
-
Jakob Hauser authored
After reading the data from the DEVICE_ID register, mask 0x0f needs to be applied to extract the revision of the chip [1]. The other part of the DEVICE_ID register, mask 0xf0, is a vendor identification code. That's how it is set up at similar products of Richtek, e.g. RT9455 [2] page 21 top. [1] https://github.com/msm8916-mainline/linux-downstream/blob/GT-I9195I/drivers/mfd/rt5033_core.c#L484 [2] https://www.richtek.com/assets/product_file/RT9455/DS9455-00.pdfSigned-off-by:
-
Stephan Gerhold authored
The fuel gauge in the RT5033 PMIC (rt5033-battery) has its own I2C bus and interrupt lines. Therefore, it is not part of the MFD device and needs to be specified separately in the device tree. Fixes: 0b271258 ("mfd: rt5033: Add Richtek RT5033 driver core.") Signed-off-by:
Stephan Gerhold <stephan@gerhold.net> Signed-off-by:
-
- 02 Jun, 2023 1 commit
-
-
Naresh Solanki authored
The previous version of this driver included wildcards in file names and descriptions. This patch renames the driver to only support MAX5970 and MAX5978, which are the only chips that the driver actually supports. Signed-off-by:
Naresh Solanki <Naresh.Solanki@9elements.com> Link: https://lore.kernel.org/r/20230427113046.3971425-1-Naresh.Solanki@9elements.comSigned-off-by:
-
