The latest spec "I-IPA01-0266-USR Rev 10" limit the MID field length to 12 bit
value. For previous versions it is 16 bit value.

This change will not break the backward compatibility as the latest ID value is
7 and with in the 12 bit value limit.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

eTSEC of-nodes may have children which are not queue-group nodes. For
example new-style fixed-phy declarations. These where incorrectly
assumed to be additional queue-groups.

Change the search to filter out any nodes which are not queue-groups,
or have been disabled.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter/IPVS fixes for net

The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:

1) Don't truncate ethernet protocol type to u8 in nft_compat, from
   Arturo Borrero.

2) Fix several problems in the addition/deletion of elements in nf_tables.

3) Fix module refcount leak in ip_vs_sync, from Julian Anastasov.

4) Fix a race condition in the abort path in the nf_tables transaction
   infrastructure. Basically aborted rules can show up as active rules
   until changes are unrolled, oneliner from Patrick McHardy.

5) Check for overflows in the data area of the rule, also from Patrick.

6) Fix off-by-one in the per-rule user data size field. This introduces
   a new nft_userdata structure that is placed at the beginning of the
   user data area that contains the length to save some bits from the
   rule and we only need one bit to indicate its presence, from Patrick.

7) Fix rule replacement error path, the replaced rule is deleted on
   error instead of leaving it in place. This has been fixed by relying
   on the abort path to undo the incomplete replacement.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ip_check_defrag() may be used by af_packet to defragment outgoing packets.
skb_network_offset() of af_packet's outgoing packets is not zero.
Signed-off-by: Alexander Drozdov <al.drozdov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

bcmgenet_set_wol() correctly sets MPD_PW_EN when a password is specified
to match magic packets against, however, when we switch from a
password-matching to a matching without password we would leave this bit
turned on, and GENET would only match magic packets with passwords.

This can be reproduced using the following sequence:

ethtool -s eth0 wol g
ethtool -s eth0 wol s sopass 00:11:22:33:44:55
ethtool -s eth0 wol g

The simple fix is to clear the MPD_PWD_EN bit when WAKE_MAGICSECURE is
not set.

Fixes: c51de7f3 ("net: bcmgenet: add Wake-on-LAN support code")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit de7b5b3d ("net: eth: xgene: change APM X-Gene SoC platform
ethernet to support ACPI") breaks booting with devicetree with UEFI
firmware. In that case, I get:

Unhandled fault: synchronous external abort (0x96000010) at 0xfffffc0000620010
 Internal error: : 96000010 [#1] SMP
 Modules linked in: vfat fat xfs libcrc32c ahci_xgene libahci_platform libahci
 CPU: 7 PID: 634 Comm: NetworkManager Not tainted 4.0.0-rc1+ #4
 Hardware name: AppliedMicro Mustang/Mustang, BIOS 1.1.0-rh-0.14 Mar  1 2015
 task: fffffe03d4c7e100 ti: fffffe03d4e24000 task.ti: fffffe03d4e24000
 PC is at xgene_enet_rd_mcx_mac.isra.11+0x58/0xd4
 LR is at xgene_gmac_tx_enable+0x2c/0x50
 pc : [<fffffe000069d6fc>] lr : [<fffffe000069dcc4>] pstate: 80000145
 sp : fffffe03d4e27590
 x29: fffffe03d4e27590 x28: 0000000000000000
 x27: fffffe03d4e277c0 x26: fffffe03da8fda10
 x25: fffffe03d4e2760c x24: fffffe03d49e28c0
 x23: fffffc0000620004 x22: 0000000000000000
 x21: fffffc0000620000 x20: fffffc0000620010
 x19: 000000000000000b x18: 000003ffd4a96020
 x17: 000003ff7fc1f7a0 x16: fffffe000079b9cc
 x15: 0000000000000000 x14: 0000000000000000
 x13: 0000000000000000 x12: fffffe03d4e24000
 x11: fffffe03d4e27da0 x10: 0000000000000001
 x9 : 0000000000000000 x8 : fffffe03d4e27a20
 x7 : 0000000000000000 x6 : 00000000ffffffef
 x5 : fffffe000105f7d0 x4 : fffffe00007ca8c8
 x3 : fffffe03d4e2760c x2 : 0000000000000000
 x1 : fffffc0000620000 x0 : 0000000040000000

 Process NetworkManager (pid: 634, stack limit = 0xfffffe03d4e24028)
 Stack: (0xfffffe03d4e27590 to 0xfffffe03d4e28000)
 ...
 Call trace:
 [<fffffe000069d6fc>] xgene_enet_rd_mcx_mac.isra.11+0x58/0xd4
 [<fffffe000069dcc0>] xgene_gmac_tx_enable+0x28/0x50
 [<fffffe00006a112c>] xgene_enet_open+0x2c/0x130
 [<fffffe00007b9254>] __dev_open+0xc8/0x148
 [<fffffe00007b956c>] __dev_change_flags+0x90/0x158
 [<fffffe00007b9664>] dev_change_flags+0x30/0x70
 [<fffffe00007c8ab8>] do_setlink+0x278/0x870
 [<fffffe00007c95bc>] rtnl_newlink+0x404/0x6a8
 [<fffffe00007c8040>] rtnetlink_rcv_msg+0x98/0x218
 [<fffffe00007e78e4>] netlink_rcv_skb+0xe0/0xf8
 [<fffffe00007c7f94>] rtnetlink_rcv+0x30/0x44
 [<fffffe00007e6f2c>] netlink_unicast+0xfc/0x210
 [<fffffe00007e75b8>] netlink_sendmsg+0x498/0x5ac
 [<fffffe00007990b8>] do_sock_sendmsg+0xa4/0xcc
 [<fffffe000079a958>] ___sys_sendmsg+0x1fc/0x208
 [<fffffe000079b984>] __sys_sendmsg+0x4c/0x94
 [<fffffe000079b9f8>] SyS_sendmsg+0x2c/0x3c

The problem here is that the enet hw clocks are not getting
initialized because of a test to avoid the initialization if
UEFI is used to boot. This is an incorrect test. When booting
with UEFI and devicetree, the kernel must still initialize
the enet hw clocks. If booting with ACPI, the clock hw is
not exposed to the kernel and it is that case where we want
to avoid initializing clocks.
Signed-off-by: Mark Salter <msalter@redhat.com>
Acked-by: Feng Kan <fkan@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

EEH recovery for bnx2x based adapters is not reliable on all Power
systems using the default hot reset, which can result in an
unrecoverable EEH error. Forcing the use of fundamental reset
during EEH recovery fixes this.

Cc: stable<stable@vger.kernel.org>
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

David Vrabel says:

====================
xen-netback: fix ethtool stats and memory leak

A couple of bug fixes for netback:
- make ethool stats to report the correct values.
- don't leak 1 MiB every time a VIF is destroyed.

Changes in v2:
- Split 2nd patch into leak fix and refactor patches
====================
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When handling a from-guest frag list, xenvif_handle_frag_list()
replaces the frags before calling the destructor to clean up the
original (foreign) frags.  Whilst this is safe (the destructor doesn't
actually use the frags), it looks odd.

Reorder the function to be less confusing.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Every time a VIF is destroyed up to 256 pages may be leaked if packets
with more than MAX_SKB_FRAGS frags were transmitted from the guest.
Even worse, if another user of ballooned pages allocated one of these
ballooned pages it would not handle the unexpectedly >1 page count
(e.g., gntdev would deadlock when unmapping a grant because the page
count would never reach 1).

When handling a from-guest skb with a frag list, unref the frags
before releasing them so they are freed correctly when the VIF is
destroyed.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use correct pointer arithmetic to get the pointer to each stat.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

I recently did a rework of the smc91x driver and did some build-testing
by compiling hundreds of randconfig kernels. Unfortunately, my script
was wrong and did not actually test the configurations that mattered,
so I introduced stupid typos in almost every file I touched.

I fixed my script now, built all configurations that actually matter
and fixed all the typos, this is the result.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: b70661c7 ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the list is traversed using rcu variant. That is not correct
since dev_set_mac_address can be called which eventually calls
rtmsg_ifinfo_build_skb and there, skb allocation can sleep. So fix this
by remove the rcu usage here.

Fixes: 3d249d4c "net: introduce ethernet teaming device"
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

When do suspend/resume stress test, some log shows "rcv is not +last".
The issue is that enet suspend will disable phy clock, phy link down,
after resume back, enet MAC redo initial and ready to tx/rx packet,
but phy still is not ready which is doing auto-negotiation. When phy
link is not up, don't schdule napi soft irq.

[Peter]
It has fixed kernel panic after long time suspend/resume test
with nfs rootfs.

[ 8864.429458] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.434799] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.440088] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.445424] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.450782] fec 2188000.ethernet eth0: rcv is not +last
[ 8864.456111] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 8864.464225] pgd = 80004000
[ 8864.466997] [00000000] *pgd=00000000
[ 8864.470627] Internal error: Oops: 17 [#1] SMP ARM
[ 8864.475353] Modules linked in: evbug
[ 8864.479006] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 4.0.0-rc1-00044-g7a2a1d2 #234
[ 8864.486854] Hardware name: Freescale i.MX6 SoloX (Device Tree)
[ 8864.492709] task: be069380 ti: be07a000 task.ti: be07a000
[ 8864.498137] PC is at memcpy+0x80/0x330
[ 8864.501919] LR is at gro_pull_from_frag0+0x34/0xa8
[ 8864.506735] pc : [<802bb080>]    lr : [<8057c204>]    psr: 00000113
[ 8864.506735] sp : be07bbd4  ip : 00000010  fp : be07bc0c
[ 8864.518235] r10: 0000000e  r9 : 00000000  r8 : 809c7754
[ 8864.523479] r7 : 809c7754  r6 : bb43c040  r5 : bd280cc0  r4 : 00000012
[ 8864.530025] r3 : 00000804  r2 : fffffff2  r1 : 00000000  r0 : bb43b83c
[ 8864.536575] Flags: nzcv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[ 8864.543904] Control: 10c5387d  Table: bd14c04a  DAC: 00000015
[ 8864.549669] Process ksoftirqd/0 (pid: 3, stack limit = 0xbe07a210)
[ 8864.555869] Stack: (0xbe07bbd4 to 0xbe07c000)
[ 8864.560250] bbc0:                                              bd280cc0 bb43c040 809c7754
[ 8864.568455] bbe0: 809c7754 bb43b83c 00000012 8057c204 00000000 bd280cc0 bd8a0718 00000003
[ 8864.576658] bc00: be07bc5c be07bc10 8057ebf0 8057c1dc 00000000 00000000 8057ecc4 bef59760
[ 8864.584863] bc20: 00000002 bd8a0000 be07bc64 809c7754 00000000 bd8a0718 bd280cc0 bd8a0000
[ 8864.593066] bc40: 00000000 0000001c 00000000 bd8a0000 be07bc74 be07bc60 8057f148 8057eb90
[ 8864.601268] bc60: bf0810a0 00000000 be07bcf4 be07bc78 8044e7b4 8057f12c 00000000 8007df6c
[ 8864.609470] bc80: bd8a0718 00000040 00000000 bd280a80 00000002 00000019 bd8a0600 bd8a1214
[ 8864.617672] bca0: bd8a0690 bf0810a0 00000000 00000000 bd8a1000 00000000 00000027 bd280cc0
[ 8864.625874] bcc0: 80062708 800625cc 000943db bd8a0718 00000001 000d1166 00000040 be7c1ec0
[ 8864.634077] bce0: 0000012c be07bd00 be07bd3c be07bcf8 8057fc98 8044e3ac 809c2ec0 3ddff000
[ 8864.642280] bd00: be07bd00 be07bd00 be07bd08 be07bd08 00000000 00000020 809c608c 00000003
[ 8864.650481] bd20: 809c6080 40000001 809c6088 00200100 be07bd84 be07bd40 8002e690 8057fac8
[ 8864.658684] bd40: be07bd64 be07bd50 00000001 04208040 000d1165 0000000a be07bd84 809c0d7c
[ 8864.666885] bd60: 00000000 809c6af8 00000000 00000001 be008000 00000000 be07bd9c be07bd88
[ 8864.675087] bd80: 8002eb64 8002e564 00000125 809c0d7c be07bdc4 be07bda0 8006f100 8002eaac
[ 8864.683291] bda0: c080e10c be07bde8 809c6c6c c080e100 00000002 00000000 be07bde4 be07bdc8
[ 8864.691492] bdc0: 800087a0 8006f098 806f2934 20000013 ffffffff be07be1c be07be44 be07bde8
[ 8864.699695] bde0: 800133a4 80008784 00000001 00000001 00000000 00000000 be7c1680 00000000
[ 8864.707896] be00: be0cfe00 bd93eb40 00000002 00000000 00000000 be07be44 be07be00 be07be30
[ 8864.716098] be20: 8006278c 806f2934 20000013 ffffffff be069380 be7c1680 be07be7c be07be48
[ 8864.724300] be40: 80049cfc 806f2910 00000001 00000000 80049cb4 00000000 be07be7c be7c1680
[ 8864.732502] be60: be3289c0 be069380 bd23b600 be0cfe00 be07bebc be07be80 806ed614 80049c68
[ 8864.740706] be80: be07a000 0000020a 809c608c 00000003 00000001 8002e858 be07a000 be035740
[ 8864.748907] bea0: 00000000 00000001 809d4598 00000000 be07bed4 be07bec0 806edd0c 806ed440
[ 8864.757110] bec0: be07a000 be07a000 be07bee4 be07bed8 806edd68 806edcf0 be07bef4 be07bee8
[ 8864.765311] bee0: 8002e860 806edd34 be07bf24 be07bef8 800494b0 8002e828 be069380 00000000
[ 8864.773512] bf00: be035780 be035740 8004938c 00000000 00000000 00000000 be07bfac be07bf28
[ 8864.781715] bf20: 80045928 80049398 be07bf44 00000001 00000000 be035740 00000000 00030003
[ 8864.789917] bf40: dead4ead ffffffff ffffffff 80a2716c 80b59b00 00000000 8088c954 be07bf5c
[ 8864.798120] bf60: be07bf5c 00000000 00000000 dead4ead ffffffff ffffffff 80a2716c 00000000
[ 8864.806320] bf80: 00000000 8088c954 be07bf88 be07bf88 be035780 8004584c 00000000 00000000
[ 8864.814523] bfa0: 00000000 be07bfb0 8000ed10 80045858 00000000 00000000 00000000 00000000
[ 8864.822723] bfc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 8864.830925] bfe0: 00000000 00000000 00000000 00000000 00000013 00000000 5ffbb5f7 f9fcf5e7
[ 8864.839115] Backtrace:
[ 8864.841631] [<8057c1d0>] (gro_pull_from_frag0) from [<8057ebf0>] (dev_gro_receive+0x6c/0x3f8)
[ 8864.850173]  r6:00000003 r5:bd8a0718 r4:bd280cc0 r3:00000000
[ 8864.855958] [<8057eb84>] (dev_gro_receive) from [<8057f148>] (napi_gro_receive+0x28/0xac)
[ 8864.864152]  r10:bd8a0000 r9:00000000 r8:0000001c r7:00000000 r6:bd8a0000 r5:bd280cc0
[ 8864.872115]  r4:bd8a0718
[ 8864.874713] [<8057f120>] (napi_gro_receive) from [<8044e7b4>] (fec_enet_rx_napi+0x414/0xc74)
[ 8864.883167]  r5:00000000 r4:bf0810a0
[ 8864.886823] [<8044e3a0>] (fec_enet_rx_napi) from [<8057fc98>] (net_rx_action+0x1dc/0x2ec)
[ 8864.895016]  r10:be07bd00 r9:0000012c r8:be7c1ec0 r7:00000040 r6:000d1166 r5:00000001
[ 8864.902982]  r4:bd8a0718
[ 8864.905570] [<8057fabc>] (net_rx_action) from [<8002e690>] (__do_softirq+0x138/0x2c4)
[ 8864.913417]  r10:00200100 r9:809c6088 r8:40000001 r7:809c6080 r6:00000003 r5:809c608c
[ 8864.921382]  r4:00000020
[ 8864.923966] [<8002e558>] (__do_softirq) from [<8002eb64>] (irq_exit+0xc4/0x138)
[ 8864.931289]  r10:00000000 r9:be008000 r8:00000001 r7:00000000 r6:809c6af8 r5:00000000
[ 8864.939252]  r4:809c0d7c
[ 8864.941841] [<8002eaa0>] (irq_exit) from [<8006f100>] (__handle_domain_irq+0x74/0xe8)
[ 8864.949688]  r4:809c0d7c r3:00000125
[ 8864.953342] [<8006f08c>] (__handle_domain_irq) from [<800087a0>] (gic_handle_irq+0x28/0x68)
[ 8864.961707]  r9:00000000 r8:00000002 r7:c080e100 r6:809c6c6c r5:be07bde8 r4:c080e10c
[ 8864.969597] [<80008778>] (gic_handle_irq) from [<800133a4>] (__irq_svc+0x44/0x5c)
[ 8864.977097] Exception stack(0xbe07bde8 to 0xbe07be30)
[ 8864.982173] bde0:                   00000001 00000001 00000000 00000000 be7c1680 00000000
[ 8864.990377] be00: be0cfe00 bd93eb40 00000002 00000000 00000000 be07be44 be07be00 be07be30
[ 8864.998573] be20: 8006278c 806f2934 20000013 ffffffff
[ 8865.003638]  r7:be07be1c r6:ffffffff r5:20000013 r4:806f2934
[ 8865.009447] [<806f2904>] (_raw_spin_unlock_irq) from [<80049cfc>] (finish_task_switch+0xa0/0x160)
[ 8865.018334]  r4:be7c1680 r3:be069380
[ 8865.021993] [<80049c5c>] (finish_task_switch) from [<806ed614>] (__schedule+0x1e0/0x5dc)
[ 8865.030098]  r8:be0cfe00 r7:bd23b600 r6:be069380 r5:be3289c0 r4:be7c1680
[ 8865.036942] [<806ed434>] (__schedule) from [<806edd0c>] (preempt_schedule_common+0x28/0x44)
[ 8865.045307]  r9:00000000 r8:809d4598 r7:00000001 r6:00000000 r5:be035740 r4:be07a000
[ 8865.053197] [<806edce4>] (preempt_schedule_common) from [<806edd68>] (_cond_resched+0x40/0x48)
[ 8865.061822]  r4:be07a000 r3:be07a000
[ 8865.065472] [<806edd28>] (_cond_resched) from [<8002e860>] (run_ksoftirqd+0x44/0x64)
[ 8865.073252] [<8002e81c>] (run_ksoftirqd) from [<800494b0>] (smpboot_thread_fn+0x124/0x190)
[ 8865.081550] [<8004938c>] (smpboot_thread_fn) from [<80045928>] (kthread+0xdc/0xf8)
[ 8865.089133]  r10:00000000 r9:00000000 r8:00000000 r7:8004938c r6:be035740 r5:be035780
[ 8865.097097]  r4:00000000 r3:be069380
[ 8865.100752] [<8004584c>] (kthread) from [<8000ed10>] (ret_from_fork+0x14/0x24)
[ 8865.107990]  r7:00000000 r6:00000000 r5:8004584c r4:be035780
[ 8865.113767] Code: e320f000 e4913004 e4914004 e4915004 (e4916004)
[ 8865.120006] ---[ end trace b0a4c6bd499288ca ]---
[ 8865.124697] Kernel panic - not syncing: Fatal exception in interrupt
[ 8865.131084] ---[ end Kernel panic - not syncing: Fatal exception in interrupt

Cc: [v3.19+] stable@vger.kernel.org
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Iyappan Subramanian says:

====================
drivers: net: xgene: Fix backward compatibility of newer firmware with older kernel

Kernel 3.17 driver supports only RGMII ethernet interface.
Since the Tianocore DT contains same compatibility string for RGMII,
SGMII based 1G and XFI based 10G interfaces, crash happens when probe called
on SGMII based 1G and XFI based 10G interface.

This patch fixes the backward compatibility of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.

v2: Address comments from v1
* updated cover letter subject line with net: xgene
* Documentation: formatted compatible string values as list

v1:
* Initial version
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the backward compatibile of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the backward compatibility of the older driver with the
newer firmware by making the binding unique so that the older driver won't
recognize the non-supported interfaces.

The new bindings are in sync with the newer firmware.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Tested-by: Mark Langsdorf <mlangsdo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. For an IPv4 ping socket, ping_check_bind_addr does not check
   the family of the socket address that's passed in. Instead,
   make it behave like inet_bind, which enforces either that the
   address family is AF_INET, or that the family is AF_UNSPEC and
   the address is 0.0.0.0.
2. For an IPv6 ping socket, ping_check_bind_addr returns EINVAL
   if the socket family is not AF_INET6. Return EAFNOSUPPORT
   instead, for consistency with inet6_bind.
3. Make ping_v4_sendmsg and ping_v6_sendmsg return EAFNOSUPPORT
   instead of EINVAL if an incorrect socket address structure is
   passed in.
4. Make IPv6 ping sockets be IPv6-only. The code does not support
   IPv4, and it cannot easily be made to support IPv4 because
   the protocol numbers for ICMP and ICMPv6 are different. This
   makes connect(::ffff:192.0.2.1) fail with EAFNOSUPPORT instead
   of making the socket unusable.

Among other things, this fixes an oops that can be triggered by:

    int s = socket(AF_INET, SOCK_DGRAM, IPPROTO_ICMP);
    struct sockaddr_in6 sin6 = {
        .sin6_family = AF_INET6,
        .sin6_addr = in6addr_any,
    };
    bind(s, (struct sockaddr *) &sin6, sizeof(sin6));

Change-Id: If06ca86d9f1e4593c0d6df174caca3487c57a241
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case there was some tx buffer reclaimed and not enough rx packets
to consume the whole budget, napi_complete would not be called and
interrupts would be kept disabled, effectively resulting in the
network core never to call the poll callback again and no rx/tx
interrupts to be fired either.

Fix that by only accounting the rx work done in the poll callback.
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently we're getting IRQs after lots of resources are already
allocated:
 * netdev
 * clocks
 * MDIO bus
Also HW gets initialized by the time when checking IRQs as well.

Now there's a possibility for master interrupt controller to be not
probed yet. This will lead to exit from GMAC probe routine with "-
EPROBE_DEFER" and so deferred probe will hapen later on.

But since we exited the first GMAC probe without release of all
allocated resources there could be conflicts on subsequent probes.

For example this is what happens for me:
 --->8---
 stmmaceth e0018000.ethernet: no reset control found
 stmmac - user ID: 0x10, Synopsys ID: 0x37
  Ring mode enabled
  DMA HW capability register supported
  Normal descriptors
  RX Checksum Offload Engine supported (type 2)
  TX Checksum insertion supported
  Enable RX Mitigation via HW Watchdog Timer
 libphy: stmmac: probed
 eth0: PHY ID 20005c7a at 1 IRQ POLL (stmmac-0:01) active
 platform e0018000.ethernet: Driver stmmaceth requests probe deferral
 ...
 ...
 ...
 stmmaceth e0018000.ethernet: no reset control found
 stmmac - user ID: 0x10, Synopsys ID: 0x37
  Ring mode enabled
  DMA HW capability register supported
  Normal descriptors
  RX Checksum Offload Engine supported (type 2)
  TX Checksum insertion supported
  Enable RX Mitigation via HW Watchdog Timer
 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 6 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x4e/0x68()
 sysfs: cannot create duplicate filename
'/devices/platform/axs10x_mb/e0018000.ethernet/mdio_bus/stmmac-0'
 CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.0.0-rc1-next-20150303+#8
 Workqueue: deferwq deferred_probe_work_func

 Stack Trace:
  arc_unwind_core+0xb8/0x114
  warn_slowpath_common+0x5a/0x8c
  warn_slowpath_fmt+0x2e/0x38
  sysfs_warn_dup+0x4e/0x68
  sysfs_create_dir_ns+0x98/0xa0
  kobject_add_internal+0x8c/0x2e8
  kobject_add+0x4a/0x8c
  device_add+0xc6/0x448
  mdiobus_register+0x6c/0x164
  stmmac_mdio_register+0x112/0x264
  stmmac_dvr_probe+0x6c0/0x85c
  stmmac_pltfr_probe+0x2e4/0x50c
  platform_drv_probe+0x26/0x5c
  really_probe+0x76/0x1dc
  bus_for_each_drv+0x42/0x7c
  device_attach+0x64/0x6c
  bus_probe_device+0x74/0xa4
  deferred_probe_work_func+0x50/0x84
  process_one_work+0xf8/0x2cc
  worker_thread+0x110/0x478
  kthread+0x8a/0x9c
  ret_from_fork+0x14/0x18
 ---[ end trace a2dfaa7d630c8be1 ]---
 ------------[ cut here ]------------
 WARNING: CPU: 0 PID: 6 at lib/kobject.c:240
kobject_add_internal+0x218/0x2e8()
 kobject_add_internal failed for stmmac-0 with -EEXIST, don't try to
register things with the same name in the same di.
 CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G        W
4.0.0-rc1-next-20150303+ #8
 Workqueue: deferwq deferred_probe_work_func

 Stack Trace:
  arc_unwind_core+0xb8/0x114
  warn_slowpath_common+0x5a/0x8c
  warn_slowpath_fmt+0x2e/0x38
  kobject_add_internal+0x218/0x2e8
  kobject_add+0x4a/0x8c
  device_add+0xc6/0x448
  mdiobus_register+0x6c/0x164
  stmmac_mdio_register+0x112/0x264
  stmmac_dvr_probe+0x6c0/0x85c
  stmmac_pltfr_probe+0x2e4/0x50c
  platform_drv_probe+0x26/0x5c
  really_probe+0x76/0x1dc
  bus_for_each_drv+0x42/0x7c
  device_attach+0x64/0x6c
  bus_probe_device+0x74/0xa4
  deferred_probe_work_func+0x50/0x84
  process_one_work+0xf8/0x2cc
  worker_thread+0x110/0x478
  kthread+0x8a/0x9c
  ret_from_fork+0x14/0x18
 ---[ end trace a2dfaa7d630c8be2 ]---
 libphy: mii_bus stmmac-0 failed to register
 : Cannot register as MDIO bus
 stmmac_pltfr_probe: main driver probe failed
 stmmaceth: probe of e0018000.ethernet failed with error -22
 --->8---

Essential fix is to check for IRQs availability as early as possible and
then safely go to deferred probe if IRQs are not there yet.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull dma-buf fixes from Sumit Semwal:
 "Minor timeout & other fixes on reservation/fence"

* tag 'dma-buf-for-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
  reservation: Remove shadowing local variable 'ret'
  dma-buf/fence: don't wait when specified timeout is zero
  reservation: wait only with non-zero timeout specified (v3)

Pull KVM fixes from Marcelo Tosatti:
 "KVM bug fixes, including a SVM interrupt injection regression fix,
  MIPS and ARM bug fixes"

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: MIPS: Enable after disabling interrupt
  KVM: MIPS: Fix trace event to save PC directly
  KVM: SVM: fix interrupt injection (apic->isr_count always 0)
  KVM: emulate: fix CMPXCHG8B on 32-bit hosts
  KVM: VMX: fix build without CONFIG_SMP
  arm/arm64: KVM: Add exit reaons to kvm_exit event tracing
  ARM: KVM: Fix size check in __coherent_cache_guest_page

In general, if a transaction object is added to the list successfully,
we can rely on the abort path to undo what we've done. This allows us to
simplify the error handling of the rule replacement path in
nf_tables_newrule().

This implicitly fixes an unnecessary removal of the old rule, which
needs to be left in place if we fail to replace.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

The NFT_USERDATA_MAXLEN is defined to 256, however we only have a u8
to store its size. Introduce a struct nft_userdata which contains a
length field and indicate its presence using a single bit in the rule.

The length field of struct nft_userdata is also a u8, however we don't
store zero sized data, so the actual length is udata->len + 1.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Check that the space required for the expressions doesn't exceed the
size of the dlen field, which would lead to the iterators crashing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

A race condition exists in the rule transaction code for rules that
get added and removed within the same transaction.

The new rule starts out as inactive in the current and active in the
next generation and is inserted into the ruleset. When it is deleted,
it is additionally set to inactive in the next generation as well.

On commit the next generation is begun, then the actions are finalized.
For the new rule this would mean clearing out the inactive bit for
the previously current, now next generation.

However nft_rule_clear() clears out the bits for *both* generations,
activating the rule in the current generation, where it should be
deactivated due to being deleted. The rule will thus be active until
the deletion is finalized, removing the rule from the ruleset.

Similarly, when aborting a transaction for the same case, the undo
of insertion will remove it from the RCU protected rule list, the
deletion will clear out all bits. However until the next RCU
synchronization after all operations have been undone, the rule is
active on CPUs which can still see the rule on the list.

Generally, there may never be any modifications of the current
generations' inactive bit since this defeats the entire purpose of
atomicity. Change nft_rule_clear() to only touch the next generations
bit to fix this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Pull ARC fixes from Vineet Gupta:
 - Fix for /proc/<pid>/maps "stack" vma annotation
 - sched stats not printing correct sleeping task PC
 - perf not reporting page faults

* tag 'arc-4.0-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: Fix thread_saved_pc()
  ARC: Fix KSTK_ESP()
  ARC: perf: Enable generic software events
  ARC: Make arc_unwind_core accessible externally

Pull powerpc fixes from Michael Ellerman:
 - Fix for dynticks.
 - Fix for smpboot bug.
 - Fix for IOMMU group refcounting.

* tag 'powerpc-4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
  powerpc/iommu: Remove IOMMU device references via bus notifier
  powerpc/smp: Wait until secondaries are active & online
  powerpc: Re-enable dynticks

After d905c5df ("PPC: POWERNV: move iommu_add_device earlier"), the
refcnt on the kobject backing the IOMMU group for a PCI device is
elevated by each call to pci_dma_dev_setup_pSeriesLP() (via
set_iommu_table_base_and_group). When we go to dlpar a multi-function
PCI device out:

        iommu_reconfig_notifier ->
                iommu_free_table ->
                        iommu_group_put
                        BUG_ON(tbl->it_group)

We trip this BUG_ON, because there are still references on the table, so
it is not freed. Fix this by moving the powernv bus notifier to common
code and calling it for both powernv and pseries.

Fixes: d905c5df ("PPC: POWERNV: move iommu_add_device earlier")
Signed-off-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Anton has a busy ppc64le KVM box where guests sometimes hit the infamous
"kernel BUG at kernel/smpboot.c:134!" issue during boot:

  BUG_ON(td->cpu != smp_processor_id());

Basically a per CPU hotplug thread scheduled on the wrong CPU. The oops
output confirms it:

  CPU: 0
  Comm: watchdog/130

The problem is that we aren't ensuring the CPU active bit is set for the
secondary before allowing the master to continue on. The master unparks
the secondary CPU's kthreads and the scheduler looks for a CPU to run
on. It calls select_task_rq() and realises the suggested CPU is not in
the cpus_allowed mask. It then ends up in select_fallback_rq(), and
since the active bit isnt't set we choose some other CPU to run on.

This seems to have been introduced by 6acbfb96 "sched: Fix hotplug
vs. set_cpus_allowed_ptr()", which changed from setting active before
online to setting active after online. However that was in turn fixing a
bug where other code assumed an active CPU was also online, so we can't
just revert that fix.

The simplest fix is just to spin waiting for both active & online to be
set. We already have a barrier prior to set_cpu_online() (which also
sets active), to ensure all other setup is completed before online &
active are set.

Fixes: 6acbfb96 ("sched: Fix hotplug vs. set_cpus_allowed_ptr()")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Pull nfsd fixes from Bruce Fields:
 "Three miscellaneous bugfixes, most importantly the clp->cl_revoked
  bug, which we've seen several reports of people hitting"

* 'for-4.0' of git://linux-nfs.org/~bfields/linux:
  sunrpc: integer underflow in rsc_parse()
  nfsd: fix clp->cl_revoked list deletion causing softlock in nfsd
  svcrpc: fix memory leak in gssp_accept_sec_context_upcall

Pull networking fixes from David Miller:

 1) If an IPVS tunnel is created with a mixed-family destination
    address, it cannot be removed.  Fix from Alexey Andriyanov.

 2) Fix module refcount underflow in netfilter's nft_compat, from Pablo
    Neira Ayuso.

 3) Generic statistics infrastructure can reference variables sitting on
    a released function stack, therefore use dynamic allocation always.
    Fix from Ignacy Gawędzki.

 4) skb_copy_bits() return value test is inverted in ip_check_defrag().

 5) Fix network namespace exit in openvswitch, we have to release all of
    the per-net vports.  From Pravin B Shelar.

 6) Fix signedness bug in CAIF's cfpkt_iterate(), from Dan Carpenter.

 7) Fix rhashtable grow/shrink behavior, only expand during inserts and
    shrink during deletes.  From Daniel Borkmann.

 8) Netdevice names with semicolons should never be allowed, because
    they serve as a separator.  From Matthew Thode.

 9) Use {,__}set_current_state() where appropriate, from Fabian
    Frederick.

10) Revert byte queue limits support in r8169 driver, it's causing
    regressions we can't figure out.

11) tcp_should_expand_sndbuf() erroneously uses tp->packets_out to
    measure packets in flight, properly use tcp_packets_in_flight()
    instead.  From Neal Cardwell.

12) Fix accidental removal of support for bluetooth in CSR based Intel
    wireless cards.  From Marcel Holtmann.

13) We accidently added a behavioral change between native and compat
    tasks, wrt testing the MSG_CMSG_COMPAT bit.  Just ignore it if the
    user happened to set it in a native binary as that was always the
    behavior we had.  From Catalin Marinas.

14) Check genlmsg_unicast() return valud in hwsim netlink tx frame
    handling, from Bob Copeland.

15) Fix stale ->radar_required setting in mac80211 that can prevent
    starting new scans, from Eliad Peller.

16) Fix memory leak in nl80211 monitor, from Johannes Berg.

17) Fix race in TX index handling in xen-netback, from David Vrabel.

18) Don't enable interrupts in amx-xgbe driver until all software et al.
    state is ready for the interrupt handler to run.  From Thomas
    Lendacky.

19) Add missing netlink_ns_capable() checks to rtnl_newlink(), from Eric
    W Biederman.

20) The amount of header space needed in macvtap was not calculated
    properly, fix it otherwise we splat past the beginning of the
    packet.  From Eric Dumazet.

21) Fix bcmgenet TCP TX perf regression, from Jaedon Shin.

22) Don't raw initialize or mod timers, use setup_timer() and
    mod_timer() instead.  From Vaishali Thakkar.

23) Fix software maintained statistics in bcmgenet and systemport
    drivers, from Florian Fainelli.

24) DMA descriptor updates in sh_eth need proper memory barriers, from
    Ben Hutchings.

25) Don't do UDP Fragmentation Offload on RAW sockets, from Michal
    Kubecek.

26) Openvswitch's non-masked set actions aren't constructed properly
    into netlink messages, fix from Joe Stringer.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
  openvswitch: Fix serialization of non-masked set actions.
  gianfar: Reduce logging noise seen due to phy polling if link is down
  ibmveth: Add function to enable live MAC address changes
  net: bridge: add compile-time assert for cb struct size
  udp: only allow UFO for packets from SOCK_DGRAM sockets
  sh_eth: Really fix padding of short frames on TX
  Revert "sh_eth: Enable Rx descriptor word 0 shift for r8a7790"
  sh_eth: Fix RX recovery on R-Car in case of RX ring underrun
  sh_eth: Ensure proper ordering of descriptor active bit write/read
  net/mlx4_en: Disbale GRO for incoming loopback/selftest packets
  net/mlx4_core: Fix wrong mask and error flow for the update-qp command
  net: systemport: fix software maintained statistics
  net: bcmgenet: fix software maintained statistics
  rxrpc: don't multiply with HZ twice
  rxrpc: terminate retrans loop when sending of skb fails
  net/hsr: Fix NULL pointer dereference and refcnt bugs when deleting a HSR interface.
  net: pasemi: Use setup_timer and mod_timer
  net: stmmac: Use setup_timer and mod_timer
  net: 8390: axnet_cs: Use setup_timer and mod_timer
  net: 8390: pcnet_cs: Use setup_timer and mod_timer
  ...

Set actions consist of a regular OVS_KEY_ATTR_* attribute nested inside
of a OVS_ACTION_ATTR_SET action attribute. When converting masked actions
back to regular set actions, the inner attribute length was not changed,
ie, double the length being serialized. This patch fixes the bug.

Fixes: 83d2b9ba ("net: openvswitch: Support masked set actions.")
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 6ce29b0e ("gianfar: Avoid unnecessary reg accesses in adjust_link()")
eliminates unnecessary calls to adjust_link for phy devices which don't support
interrupts and need polling. As part of that work, the 'new_state' local flag,
which was used to reduce logging noise on the console, was eliminated.

Unfortunately, that means that a 'Link is Down' log message will now be
issued continuously if a link is configured as UP, the link state is down,
and the associated phy requires polling. This occurs because priv->oldduplex
is -1 in this case, which always differs from phydev->duplex. In addition,
phydev->speed may also differ from priv->oldspeed.  gfar_update_link_state()
is therefore called each time a phy is polled, even if the link state did not
change.

Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a function that will enable changing the MAC address
of an ibmveth interface while it is still running.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>

make build fail if structure no longer fits into ->cb storage.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a tricky story of the new atomic state handling and the legacy
code fighting over each another. The bug at hand is an underrun of the
framebuffer reference with subsequent hilarity caused by the load
detect code. Which is peculiar since the the exact same code works
fine as the implementation of the legacy setcrtc ioctl.

Let's look at the ingredients:

- Currently our code is a crazy mix of legacy modeset interfaces to
  set the parameters and half-baked atomic state tracking underneath.
  While this transition is going we're using the transitional plane
  helpers to update the atomic side (drm_plane_helper_disable/update
  and friends), i.e. plane->state->fb. Since the state structure owns
  the fb those functions take care of that themselves.

  The legacy state (specifically crtc->primary->fb) is still managed
  by the old code (and mostly by the drm core), with the fb reference
  counting done by callers (core drm for the ioctl or the i915 load
  detect code). The relevant commit is

  commit ea2c67bb
  Author: Matt Roper <matthew.d.roper@intel.com>
  Date:   Tue Dec 23 10:41:52 2014 -0800

      drm/i915: Move to atomic plane helpers (v9)

- drm_plane_helper_disable has special code to handle multiple calls
  in a row - it checks plane->crtc == NULL and bails out. This is to
  match the proper atomic implementation which needs the crtc to get
  at the implied locking context atomic updates always need. See

  commit acf24a39
  Author: Daniel Vetter <daniel.vetter@ffwll.ch>
  Date:   Tue Jul 29 15:33:05 2014 +0200

      drm/plane-helper: transitional atomic plane helpers

- The universal plane code split out the implicit primary plane from
  the CRTC into it's own full-blown drm_plane object. As part of that
  the setcrtc ioctl (which updated both the crtc mode and primary
  plane) learned to set crtc->primary->crtc on modeset to make sure
  the plane->crtc assignments statate up to date in

  commit e13161af
  Author: Matt Roper <matthew.d.roper@intel.com>
  Date:   Tue Apr 1 15:22:38 2014 -0700

      drm: Add drm_crtc_init_with_planes() (v2)

  Unfortunately we've forgotten to update the load detect code. Which
  wasn't a problem since the load detect modeset is temporary and
  always undone before we drop the locks.

- Finally there is a organically grown history (i.e. don't ask) around
  who sets the legacy plane->fb for the various driver entry points.
  Originally updating that was the drivers duty, but for almost all
  places we've moved that (plus updating the refcounts) into the core.
  Again the exception is the load detect code.

Taking all together the following happens:
- The load detect code doesn't set crtc->primary->crtc. This is only
  really an issue on crtcs never before used or when userspace
  explicitly disabled the primary plane.

- The plane helper glue code short-circuits because of that and leaves
  a non-NULL fb behind in plane->state->fb and plane->fb. The state
  fb isn't a real problem (it's properly refcounted on its own), it's
  just the canary.

- Load detect code drops the reference for that fb, but doesn't set
  plane->fb = NULL. This is ok since it's still living in that old
  world where drivers had to clear the pointer but the core/callers
  handled the refcounting.

- On the next modeset the drm core notices plane->fb and takes care of
  refcounting it properly by doing another unref. This drops the
  refcount to zero, leaving state->plane now pointing at freed memory.

- intel_plane_duplicate_state still assume it owns a reference to that
  very state->fb and bad things start to happen.

Fix this all by applying the same duct-tape as for the legacy setcrtc
ioctl code and set crtc->primary->crtc properly.

Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: Matt Roper <matthew.d.roper@intel.com>
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If an over-MTU UDP datagram is sent through a SOCK_RAW socket to a
UFO-capable device, ip_ufo_append_data() sets skb->ip_summed to
CHECKSUM_PARTIAL unconditionally as all GSO code assumes transport layer
checksum is to be computed on segmentation. However, in this case,
skb->csum_start and skb->csum_offset are never set as raw socket
transmit path bypasses udp_send_skb() where they are usually set. As a
result, driver may access invalid memory when trying to calculate the
checksum and store the result (as observed in virtio_net driver).

Moreover, the very idea of modifying the userspace provided UDP header
is IMHO against raw socket semantics (I wasn't able to find a document
clearly stating this or the opposite, though). And while allowing
CHECKSUM_NONE in the UFO case would be more efficient, it would be a bit
too intrusive change just to handle a corner case like this. Therefore
disallowing UFO for packets from SOCK_DGRAM seems to be the best option.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>