- 04 May, 2016 6 commits
-
-
Sudeep Holla authored
Currently when performing random CPU hot-plugs and suspend-to-ram(S2R) on systems using arm_big_little cpufreq driver, we get warnings similar to something like below: cpu cpu1: _opp_add: duplicate OPPs detected. Existing: freq: 600000000, volt: 800000, enabled: 1. New: freq: 600000000, volt: 800000, enabled: 1 This is mainly because the OPPs for the shared cpus are not set. We can just use dev_pm_opp_of_cpumask_add_table in case the OPPs are obtained from DT(arm_big_little_dt.c) or use dev_pm_opp_set_sharing_cpus if the OPPs are obtained by other means like firmware(e.g. scpi-cpufreq.c) Also now that the generic dev_pm_opp{,_of}_cpumask_remove_table can handle removal of opp table and entries for all associated CPUs, we can re-use dev_pm_opp{,_of}_cpumask_remove_table as free_opp_table in cpufreq_arm_bL_ops. This patch makes necessary changes to reuse the generic OPP functions for {init,free}_opp_table and thereby eliminating the warnings. Signed-off-by:Sudeep Holla <sudeep.holla@arm.com> Acked-by:
Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-
Rafael J. Wysocki authored
-
Sudeep Holla authored
Functions dev_pm_opp_of_{cpumask_,}remove_table removes/frees all the static OPP entries associated with the device and/or all cpus(in case of cpumask) that are created from DT. However the OPP entries are populated reading from the firmware or some different method using dev_pm_opp_add are marked dynamic and can't be removed using above functions. This patch adds non DT/OF versions of dev_pm_opp_{cpumask_,}remove_table to support the above mentioned usecase. This is in preparation to make use of the same in scpi-cpufreq.c Signed-off-by:Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Marc Gonzalez authored
Add tango4 compatible string to the list. Signed-off-by:
Marc Gonzalez <marc_gonzalez@sigmadesigns.com> Acked-by:
-
Arnd Bergmann authored
The new use of dev_pm_opp_set_sharing_cpus resulted in a harmless compiler warning with CONFIG_CPUMASK_OFFSTACK=y: drivers/cpufreq/mvebu-cpufreq.c: In function 'armada_xp_pmsu_cpufreq_init': include/linux/cpumask.h:550:25: error: passing argument 2 of 'dev_pm_opp_set_sharing_cpus' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers] The problem here is that cpumask_var_t gets passed by reference, but by declaring a 'const cpumask_var_t' argument, only the pointer is constant, not the actual mask. This is harmless because the function does not actually modify the mask. This patch changes the function prototypes for all of the related functions to pass a 'struct cpumask *' instead of 'cpumask_var_t', matching what most other such functions do in the kernel. This lets us mark all the other similar functions as taking a 'const' mask where possible, and it avoids the warning without any change in object code. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: 947bd567 (mvebu: Use dev_pm_opp_set_sharing_cpus() to mark OPP tables as shared) Acked-by:
Pavel Machek <pavel@ucw.cz> Acked-by:
-
Sai Gurrappadi authored
Currently, the userspace governor only updates frequency on GOV_LIMITS if policy->cur falls outside policy->{min/max}. However, it is also necessary to update current frequency on GOV_LIMITS to match the user requested value if it can be achieved within the new policy->{max/min}. This was previously the behaviour in the governor until commit d1922f02 ("cpufreq: Simplify userspace governor") which incorrectly assumed that policy->cur == user requested frequency via scaling_setspeed. This won't be true if the user requested frequency falls outside policy->{min/max}. Ex: a temporary thermal cap throttled the user requested frequency. Fix this by storing the user requested frequency in a seperate variable. The governor will then try to achieve this request on every GOV_LIMITS change. Fixes: d1922f02 (cpufreq: Simplify userspace governor) Signed-off-by:Sai Gurrappadi <sgurrappadi@nvidia.com> Acked-by:
-
- 28 Apr, 2016 9 commits
-
-
Viresh Kumar authored
Move cpufreq bits for mvebu into drivers/cpufreq/ directory, that's where they really belong to. Compiled tested only. Signed-off-by:
-
Viresh Kumar authored
There are no more users of platform-data for cpufreq-dt driver, get rid of it. Signed-off-by:
-
Viresh Kumar authored
That will allow us to avoid using cpufreq-dt platform data. Signed-off-by:
-
Viresh Kumar authored
Existing platforms, which do not support operating-points-v2, can explicitly tell the opp core that some of the CPUs share opp tables, with help of dev_pm_opp_set_sharing_cpus(). For such platforms, explicitly ask the opp core to provide list of CPUs sharing the opp table with current cpu device, before falling back to platform data. Signed-off-by:
-
Rafael J. Wysocki authored
-
Viresh Kumar authored
OPP core allows a platform to mark OPP table as shared, when the platform isn't using operating-points-v2 bindings. And, so there should be a non DT way of finding out if the OPP table is shared or not. This patch adds dev_pm_opp_get_sharing_cpus(), which first tries to get OPP sharing information from the opp-table (in case it is already marked as shared), otherwise it uses the existing DT way of finding sharing information. Signed-off-by:
-
Viresh Kumar authored
dev_pm_opp_set_sharing_cpus() isn't supposed to update the cpumask passed as its parameter, and so it should always have been marked 'const'. Do it now. Signed-off-by:
-
Viresh Kumar authored
Some of the routines have used -ENOSYS for the cases where the functionality isn't implemented in the kernel. But ENOSYS is supposed to be used only for syscalls. Replace that with -ENOTSUPP, which specifically means that the operation isn't supported. While at it, replace exiting -EINVAL errors for similar cases to -ENOTSUPP. Signed-off-by:
-
Rafael J. Wysocki authored
The name of the prev_cpu_wall field in struct cpu_dbs_info is confusing, because it doesn't represent wall time, but the previous update time as returned by get_cpu_idle_time() (that may be the current value of jiffies_64 in some cases, for example). Moreover, the names of some related variables in dbs_update() take that confusion further. Rename all of those things to make their names reflect the purpose more accurately. While at it, drop unnecessary parens from one of the updated expressions. No functional changes. Signed-off-by:
Chen Yu <yu.c.chen@intel.com>
-
- 27 Apr, 2016 6 commits
-
-
Srinivas Pandruvada authored
For platforms which are controlled via remove node manager, enable _PPC by default. These platforms are mostly categorized as enterprise server or performance servers. These platforms needs to go through some certifications tests, which tests control via _PPC. The relative risk of enabling by default is low as this is is less likely that these systems have broken _PSS table. Signed-off-by:
Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> Signed-off-by:
-
Srinivas Pandruvada authored
When policy->max is changed via _PPC or sysfs and is more than the max non turbo frequency, it does not really change resulting performance in some processors. When policy->max results in a P-State ratio more than the turbo activation ratio, then processor can choose any P-State up to max turbo. So the user or _PPC setting has no value, but this can cause undesirable side effects like: - Showing reduced max percentage in Intel P-State sysfs - It can cause reduced max performance under certain boundary conditions: The requested max scaling frequency either via _PPC or via cpufreq-sysfs, will be converted into a fixed floating point max percent scale. In majority of the cases this will result in correct max. But not 100% of the time. If the _PPC is requested at a point where the calculation lead to a lower max, this can result in a lower P-State then expected and it will impact performance. Example of this condition using a Broadwell laptop with config TDP. ACPI _PSS table from a Broadwell laptop 2301000 2300000 2200000 2000000 1900000 1800000 1700000 1500000 1400000 1300000 1100000 1000000 900000 800000 600000 500000 The actual results by disabling config TDP so that we can get what is requested on or below 2300000Khz. scaling_max_freq Max Requested P-State Resultant scaling max ---------------------------------------- ---------------------- 2400000 18 2900000 (max turbo) 2300000 17 2300000 (max physical non turbo) 2200000 15 2100000 2100000 15 2100000 2000000 13 1900000 1900000 13 1900000 1800000 12 1800000 1700000 11 1700000 1600000 10 1600000 1500000 f 1500000 1400000 e 1400000 1300000 d 1300000 1200000 c 1200000 1100000 a 1000000 1000000 a 1000000 900000 9 900000 800000 8 800000 700000 7 700000 600000 6 600000 500000 5 500000 ------------------------------------------------------------------ Now set the config TDP level 1 ratio as 0x0b (equivalent to 1100000KHz) in BIOS (not every system will let you adjust this). The turbo activation ratio will be set to one less than that, which will be 0x0a (So any request above 1000000KHz should result in turbo region assuming no thermal limits). Here _PPC will request max to 1100000KHz (which basically should still result in turbo as this is more than the turbo activation ratio up to max allowable turbo frequency), but actual calculation resulted in a max ceiling P-State which is 0x0a. So under any load condition, this driver will not request turbo P-States. This will be a huge performance hit. When config TDP feature is ON, if the _PPC points to a frequency above turbo activation ratio, the performance can still reach max turbo. In this case we don't need to treat this as the reduced frequency in set_policy callback. In this change when config TDP is active (by checking if the physical max non turbo ratio is more than the current max non turbo ratio), any request above current max non turbo is treated as full performance. Signed-off-by:
-
Srinivas Pandruvada authored
Use ACPI _PPC notification to limit max P state driver will request. ACPI _PPC change notification is sent by BIOS to limit max P state in several cases: - Reduce impact of platform thermal condition - When Config TDP feature is used, a changed _PPC is sent to follow TDP change - Remote node managers in server want to control platform power via baseboard management controller (BMC) This change registers with ACPI processor performance lib so that _PPC changes are notified to cpufreq core, which in turns will result in call to .setpolicy() callback. Also the way _PSS table identifies a turbo frequency is not compatible to max turbo frequency in intel_pstate, so the very first entry in _PSS needs to be adjusted. This feature can be turned on by using kernel parameters: intel_pstate=support_acpi_ppc Signed-off-by:
-
Akshay Adiga authored
The frequency transition latency from pmin to pmax is observed to be in few millisecond granurality. And it usually happens to take a performance penalty during sudden frequency rampup requests. This patch set solves this problem by using an entity called "global pstates". The global pstate is a Chip-level entity, so the global entitiy (Voltage) is managed across the cores. The local pstate is a Core-level entity, so the local entity (frequency) is managed across threads. This patch brings down global pstate at a slower rate than the local pstate. Hence by holding global pstates higher than local pstate makes the subsequent rampups faster. A per policy structure is maintained to keep track of the global and local pstate changes. The global pstate is brought down using a parabolic equation. The ramp down time to pmin is set to ~5 seconds. To make sure that the global pstates are dropped at regular interval , a timer is queued for every 2 seconds during ramp-down phase, which eventually brings the pstate down to local pstate. Iozone results show fairly consistent performance boost. YCSB on redis shows improved Max latencies in most cases. Iozone write/rewite test were made with filesizes 200704Kb and 401408Kb with different record sizes . The following table shows IOoperations/sec with and without patch. Iozone Results ( in op/sec) ( mean over 3 iterations ) --------------------------------------------------------------------- file size- with without % recordsize-IOtype patch patch change ---------------------------------------------------------------------- 200704-1-SeqWrite 1616532 1615425 0.06 200704-1-Rewrite 2423195 2303130 5.21 200704-2-SeqWrite 1628577 1602620 1.61 200704-2-Rewrite 2428264 2312154 5.02 200704-4-SeqWrite 1617605 1617182 0.02 200704-4-Rewrite 2430524 2351238 3.37 200704-8-SeqWrite 1629478 1600436 1.81 200704-8-Rewrite 2415308e 2298136 5.09 200704-16-SeqWrite 1619632 1618250 0.08 200704-16-Rewrite 2396650 2352591 1.87 200704-32-SeqWrite 1632544 1598083 2.15 200704-32-Rewrite 2425119 2329743 4.09 200704-64-SeqWrite 1617812 1617235 0.03 200704-64-Rewrite 2402021 2321080 3.48 200704-128-SeqWrite 1631998 1600256 1.98 200704-128-Rewrite 2422389 2304954 5.09 200704-256 SeqWrite 1617065 1616962 0.00 200704-256-Rewrite 2432539 2301980 5.67 200704-512-SeqWrite 1632599 1598656 2.12 200704-512-Rewrite 2429270 2323676 4.54 200704-1024-SeqWrite 1618758 1616156 0.16 200704-1024-Rewrite 2431631 2315889 4.99 401408-1-SeqWrite 1631479 1608132 1.45 401408-1-Rewrite 2501550 2459409 1.71 401408-2-SeqWrite 1617095 1626069 -0.55 401408-2-Rewrite 2507557 2443621 2.61 401408-4-SeqWrite 1629601 1611869 1.10 401408-4-Rewrite 2505909 2462098 1.77 401408-8-SeqWrite 1617110 1626968 -0.60 401408-8-Rewrite 2512244 2456827 2.25 401408-16-SeqWrite 1632609 1609603 1.42 401408-16-Rewrite 2500792 2451405 2.01 401408-32-SeqWrite 1619294 1628167 -0.54 401408-32-Rewrite 2510115 2451292 2.39 401408-64-SeqWrite 1632709 1603746 1.80 401408-64-Rewrite 2506692 2433186 3.02 401408-128-SeqWrite 1619284 1627461 -0.50 401408-128-Rewrite 2518698 2453361 2.66 401408-256-SeqWrite 1634022 1610681 1.44 401408-256-Rewrite 2509987 2446328 2.60 401408-512-SeqWrite 1617524 1628016 -0.64 401408-512-Rewrite 2504409 2442899 2.51 401408-1024-SeqWrite 1629812 1611566 1.13 401408-1024-Rewrite 2507620 2442968 2.64 Tested with YCSB workload (50% update + 50% read) over redis for 1 million records and 1 million operation. Each test was carried out with target operations per second and persistence disabled. Max-latency (in us)( mean over 5 iterations ) --------------------------------------------------------------- op/s Operation with patch without patch %change --------------------------------------------------------------- 15000 Read 61480.6 50261.4 22.32 15000 cleanup 215.2 293.6 -26.70 15000 update 25666.2 25163.8 2.00 25000 Read 32626.2 89525.4 -63.56 25000 cleanup 292.2 263.0 11.10 25000 update 32293.4 90255.0 -64.22 35000 Read 34783.0 33119.0 5.02 35000 cleanup 321.2 395.8 -18.8 35000 update 36047.0 38747.8 -6.97 40000 Read 38562.2 42357.4 -8.96 40000 cleanup 371.8 384.6 -3.33 40000 update 27861.4 41547.8 -32.94 45000 Read 42271.0 88120.6 -52.03 45000 cleanup 263.6 383.0 -31.17 45000 update 29755.8 81359.0 -63.43 (test without target op/s) 47659 Read 83061.4 136440.6 -39.12 47659 cleanup 195.8 193.8 1.03 47659 update 73429.4 124971.8 -41.24 Signed-off-by:
Akshay Adiga <akshay.adiga@linux.vnet.ibm.com> Reviewed-by:
Gautham R. Shenoy <ego@linux.vnet.ibm.com> Acked-by:
-
Shilpasri G Bhat authored
commit 1b028984 ("cpufreq: powernv: Add sysfs attributes to show throttle stats") used policy->driver_data as a flag for one-time creation of throttle sysfs files. Instead of this use 'kernfs_find_and_get()' to check if the attribute already exists. This is required as policy->driver_data is used for other purposes in the later patch. Signed-off-by:
Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com> Signed-off-by:
-
Javier Martinez Canillas authored
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either built-in or as a module, use that macro instead of open coding the same. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Acked-by:
-
- 25 Apr, 2016 19 commits
-
-
Rafael J. Wysocki authored
The way cpufreq_governor_start() initializes j_cdbs->prev_load is questionable. First off, j_cdbs->prev_cpu_wall used as a denominator in the computation may be zero. The case this happens is when get_cpu_idle_time_us() returns -1 and get_cpu_idle_time_jiffy() used to return that number is called exactly at the jiffies_64 wrap time. It is rather hard to trigger that error, but it is not impossible and it will just crash the kernel then. Second, j_cdbs->prev_load is computed as the average load during the entire time since the system started and it may not reflect the load in the previous sampling period (as it is expected to). That doesn't play well with the way dbs_update() uses that value. Namely, if the update time delta (wall_time) happens do be greater than twice the sampling rate on the first invocation of it, the initial value of j_cdbs->prev_load (which may be completely off) will be returned to the caller as the current load (unless it is equal to zero and unless another CPU sharing the same policy object has a greater load value). For this reason, notice that the prev_load field of struct cpu_dbs_info is only used by dbs_update() and only in that one place, so if cpufreq_governor_start() is modified to always initialize it to 0, it will make dbs_update() always compute the actual load first time it checks the update time delta against the doubled sampling rate (after initialization) and there won't be any side effects of it. Consequently, modify cpufreq_governor_start() as described. Fixes: 18b46abd (cpufreq: governor: Be friendly towards latency-sensitive bursty workloads) Signed-off-by:
-
Viresh Kumar authored
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform device now, reuse that and remove similar code from platform code. Signed-off-by:
-
Viresh Kumar authored
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform device now, reuse that and remove similar code from platform code. Signed-off-by:
-
Viresh Kumar authored
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform device now, reuse that and remove similar code from platform code. Signed-off-by:
-
Viresh Kumar authored
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform device now, reuse that and remove similar code from platform code. Signed-off-by:
-
Finley Xiao authored
This patch add rockchip's compatible string to the compat list and remove similar code from platform code for supporting generic platdev driver. Signed-off-by:
Finley Xiao <finley.xiao@rock-chips.com> Acked-by:
Heiko Stuebner <heiko@sntech.de> Signed-off-by:
-
Viresh Kumar authored
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform device now, reuse that and remove similar code from platform code. Signed-off-by:
-
Viresh Kumar authored
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform device now, reuse that and remove similar code from platform code. Note that the complete routine imx27_dt_init() is removed as of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); has same effect as a NULL .init_machine machine callback pointer. Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Acked-by:
-
Viresh Kumar authored
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform device now, reuse that and remove similar code from platform code. Signed-off-by:
Antoine Tenart <antoine.tenart@free-electrons.com> Acked-by:
-
Viresh Kumar authored
The machines array in cpufreq-dt-platdev is used only once at boot time and so should be marked with __initconst, so that kernel can free up memory used for it, if required. Suggested-by:
Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by:
-
Viresh Kumar authored
opp core allows OPPs to be explicitly marked as shared from platform code, in case of operating-point v1 bindings. Though we do everything fine in that case, we don't set the flag in the opp-table to indicate that the OPPs are shared. It works fine today as the flag isn't used anywhere else in the core, but we should be doing the right thing by marking it set. Signed-off-by:
-
Viresh Kumar authored
Move dev_pm_opp_set_sharing_cpus() towards the end of the file. This is required for better readability after the next patch is applied, which adds dev_pm_opp_get_sharing_cpus(). Signed-off-by:
-
Viresh Kumar authored
dev_pm_opp_set_sharing_cpus() doesn't do any DT specific stuff and its declarations are added within the CONFIG_OF ifdef by mistake. Take them out of that. Signed-off-by:
-
Viresh Kumar authored
Few of the routines in cpu.c were missing these, add them. Signed-off-by:
-
Viresh Kumar authored
Don't send -EINVAL and propagate what's received from _find_opp_table(). Signed-off-by:
-
Jia Hongtao authored
Cooling device is registered by ready callback. It's also invoked while system resuming from sleep (Enabling non-boot cpus). Thus cooling device may be multiple registered. Matchable unregistration is added to exit callback to fix this issue. Signed-off-by:
Jia Hongtao <hongtao.jia@nxp.com> Signed-off-by:
-
Jia Hongtao authored
.exit callback (qoriq_cpufreq_cpu_exit()) is also used during suspend. So __exit macro should be removed or the function will be discarded. Signed-off-by:
-
Jia Hongtao authored
When THERMAL_OF is undefined the cooling device messages should not be shown. -ENOSYS is returned from of_cpufreq_cooling_register() when THERMAL_OF is undefined. Signed-off-by:
-
Ashwin Chaugule authored
Add a function to cleanup at module exit and export appropriate GPL string to enable moduler support for the cppc_cpufreq driver. Reported-by:
Srinivas Pandruvada <srinivas.pandruvada@intel.com> Signed-off-by:
Ashwin Chaugule <ashwin.chaugule@linaro.org> Signed-off-by:
-
