When using generic_buffer to read data, the scale is not properly
detected for scale shared by type. This is caused by a problem
with the generation of generic name out of the full name.
E.g.: for current->name in_accel_z, the extracted generic name
is "in" (when it should be "in_accel"). This is used in generic_buffer
to generate scale and offset paths (in_accel_scale).

Consider the in_ or out_ prefix when extracting the generic name
from the full name.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patch adds ABI documentation entries for in_rot_offset.
At least one user for these is present that is the  HID Sensors Driver.
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

MAX520 and MAX521 are protocol-compatible with the already supported
chips, just have more channels.
Signed-off-by: Antonio Fiol <antonio@fiol.es>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This patchset adds ABI documentation for the following attributes:

in_illuminance_scale, used atleast once in al3320a staging/iio/light/
in_illuminance_calibscale, used atleast once in cm32181
in_illuminance_input, used in cm3232 at least once
in_illuminance_raw used atleast once in al3320a
in_illuminance_clear_raw and in_illuminance_ir_raw exposed by
gp2ap020a00f with modifiers IIO_MOD_LIGHT_CLEAR and
IIO_MOD_LIGHT_IR respectively.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

This adds support for the LIS3LV02 accelerometer found in the
ST Microelectronics Nomadik board series.

Cc: devicetree@vger.kernel.org
Cc: Denis CIOCCA <denis.ciocca@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>

Gcc < 4.3 doesn't understand binary constants (0b*):

drivers/staging/fbtft/fbtft-sysfs.c:156:19: error: invalid suffix "b111" on integer constant
drivers/staging/fbtft/fb_hx8340bn.c:159:3: error: invalid suffix "b1111" on integer constant
drivers/staging/fbtft/fb_hx8340bn.c:159:11: error: invalid suffix "b1111" on integer constant
drivers/staging/fbtft/fb_hx8340bn.c:159:19: error: invalid suffix "b11111" on integer constant
drivers/staging/fbtft/fb_hx8340bn.c:159:28: error: invalid suffix "b1111" on integer constant
drivers/staging/fbtft/fb_hx8340bn.c:159:36: error: invalid suffix "b1111" on integer constant
drivers/staging/fbtft/fb_hx8340bn.c:159:44: error: invalid suffix "b1111" on integer constant
drivers/staging/fbtft/fb_hx8340bn.c:159:52: error: invalid suffix "b11111" on integer constant
drivers/staging/fbtft/fb_hx8340bn.c:160:3: error: invalid suffix "b111" on integer constant
...

Hence use hexadecimal constants (0x*) instead.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'iio-for-4.1a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next

Jonathan writes:

First set of new drivers, cleanups and functionality for IIO in the 4.1 cycle.

New drivers
* CM3323 color sensor.
* MS5611 pressure and temperature sensor.

New functionality
* mup6050 - create mux clients for devices described via ACPI. The reasoning
     and approach taken in this patch are complex.  Basically there is no
     otherway of finding out what is there than by some esoteric look ups in
     the ACPI data.
* cm3232 - PM support
* itg3200 - suspend/resume support
* mcp320x - add more ADCs to the kconfig to reflect what the driver supports
     (this patch and the bindings got left behind when the support was added
      a while back).

Docs / utils
* ti-adc128s052 - DT bindings.
* mcp3422 - DT bindings.
* mcp320x - DT bindings
* ABI docs for event threshold scale attributes, in_magn_offset, proximity
  scan_element and thresh falling/rising values for accelerometers.  All
  elements long in use that have slipped by being explicitly documented.
* Tidy up the tools previously in drivers/staging/iio/Documentation and move
  them out to /tools/iio. Yet another move that should have happened long ago.
  This time Roberta Dobrescu did the leg work.  Thanks!

Core Cleanups
* Export userspace IIO headers.  We should have done the appropriate header
  splitting a long time ago. Thanks to Daniel for sorting this out.

* Refactor the registring of attributes for buffers to move all non-custom
  ones to a vector allowing easier additions to the current set in the future.

Driver Cleanups
* gpiod related cleanups.  Make use of the additional parameter to specify
  	initial direciton to avoid extra code.
* bmc150 - Various refactorings to reduce code repitition and prepare for
           hardware buffer support.  Some of these cleanups are good even
	   without the new functionality.
* kmx61 - direct use of index to an array avoiding a structure element which
          was always the index to an element in an array of that structure.
* vf610 - avoid incorrect type for return from wait_for_completion_timeout.
* gp2ap020a00f - use put_unaligned_le32 for slight code simplification.
* ade7754 - improve error handling including suppressing some build warnings.
* ade7759 - improve error handling including suppressing some build warnings.
* hmc5843 - Long line and indentation fixes. Also some constifying of various
      constant data.
* ade7854 - 80+ character line splitting.
* ad2s1210 - fix wrong printf format string.
* mxs-lradc - fix wrong printf format string.
* ade7954-i2c - code alignment fixes and other trivial but worthwhile bits.
* periodic rtc trigger - make the frequency type an unsigned int as it
  is always treated as such.
* jsa1212 - constify struct regmap_config as it is constant.
* ad7793 - typo in the MODULE_DESCRIPTION
* mma9551 - check gpiod_to_irq errors.  Note that this doesn't actually cause
    any trouble but is worth tidying up as obviously incorrect.
* mlx90614 - refactor the register symbols to make it clear which reads are to
    RAM not PROM.

Remove redundant blank lines, move absolute include after relative
include.
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove unused defines from dgnc_cls.h
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dgnc_kcompat.h contains some old legacy defines in case the kernel
doesn't have __user defined but for current kernel versions these
defines don't make sense and are useless so remove them. Move the
TTY_FLIPBUF_SIZE define to digi.h because it's used in the code.
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Dgnc_types.h unnecesarily defines TRUE as 1 and FALSE as 0 because we
already have a widely used linux/types.h so convert all TRUE to true,
FALSE to false and edit the dgnc_board struct to make sure it uses
"bool".
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Dpacompat.h contained a lot of unused #defines and only few things are
used from it so since we've trimmed down digi.h, now we can delete
dpacompat.h and move remaining stuff into digi.h.
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove a lot of unused structs and defines from digi.h. We still have to
be careful with TIOCM_LE and TIOCMSET/TIOCMBIC because termios.h and
ioctls.h respectfully redefine them.
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

dgnc_ioctl_name() is never used anywhere so remove it
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

"dgnc_NumBoards" is the number of filled out elements in the
dgnc_Board[] array.  "->nasync" and "->maxports" are the same value.
They are the number of channels in the ->channels[] array so these tests
should be ">=" instead of ">" so we avoid reading past the end of the
arrays.

I cleaned up the conditions in dgnc_mgmt_ioctl() a bit.  There was a
work around for the off by one bug in the case where there were no
boards which is no longer needed.  "channel" is unsigned so it can't be
negative.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Eliminate extra indentation by putting all the code into the same block.
Also delete a bogus comment.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On some hardware the USB fails to initialize to sane state after
cold boot. We can detect this based on some unexpected interrupt bits,
and recover by re-initializing.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Fail and WARN if DMA counters are wrong.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move cvmx_usb_shutdown() to allow its use from some other functions.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't disable port before resetting. Also perform reset unconditionally
when requested.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move FIFO setup to controller reset from port reset.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move FIFO setup into a separate routine.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use USB stack to turn on the power bit. It will also do
the necessary delays.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Don't poll interrupts before we have registered the HCD.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Move one-time state data structure initialization out of
cvmx_usb_initialize().

This enables to re-initialize USBN HW block without messing
up data structures.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Never retry after xacterr. The DMA engine cannot handle that properly
and may result in wrong transfer count and hang.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Program DMA engine based on transfer direction. We are only transferring
to one direction at a time.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use __BITFIELD_FIELD to define bitfields. OCTEON can at least in theory
run also in little-endian mode, so the bitfield definitions should not
assume big-endian byte order.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since we are not moving/realigning the original pointer returned
by kmalloc, we don't need to store the value in a separate field.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove useless prefix from pipe flags and adjust comments.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Original CVMX code used "__" to distinguis internal USB functions
from public ones. But in Linux all cvmx_usb routines are internal
to this driver, so such separation is useless.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Eliminate 64-bit register access wrappers. Since we don't implement
register-level debugging outputs, these are useless.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove some function parameter sanity checks from internal functions
where we can rely them being called with sane parameters.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove function prototype from r8192U_core.c since it is
declared in the r8192U.h header and this is included in r8192U_core.c
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make functions static since they are used locally and no other files
refer them.
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Context is used in dev_info after it has been freed.
This patch fix that issue by removing the dev_info itself,
for msg doesn't look much necessary.
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the following sparse warning:

warning: symbol 'rtw_atimdone_event_callback23a' was not declared.
Should it be static?
rtw_atimdone_event_callback23a is local to the file rtw_mlme.c but
it isn't exposed in a header file anywhere. Moreover it is never called
from anywhere as well.

So, this patch removes this function completely.
Signed-off-by: Somya Anand <somyaanand214@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove typedef prism2sta_accesslist_t and replace its uses
in the code.
Signed-off-by: Vatika Harlalka <vatikaharlalka@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>