PD3.0 Spec 6.4.4.3.2 say that only Responder supports 12 or more SVIDs,
the Discover SVIDs Command Shall be executed multiple times until a
Discover SVIDs VDO is returned ending either with a SVID value of
0x0000 in the last part of the last VDO or with a VDO containing two
SVIDs with values of 0x0000.

In the current implementation, if the last VDO does not find that the
Discover SVIDs Command would be executed multiple times even if the
Responder SVIDs are less than 12, and we found some odd dockers just
meet this case. So fix it.
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Link: https://lore.kernel.org/r/20230316081149.24519-1-frank.wang@rock-chips.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Clean up the probe variable declarations by removing the stray newlines.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-12-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The probe callback has become unwieldy so break out the clock lookups
into a new helper function to improve readability.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-11-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor the PHY handling using four new helpers to initialise,
deinitialise, power on and power off all the PHYs.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-10-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Clean up the core init error handling by using descriptive names for the
error labels and releasing resourcing in reverse order consistently.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-9-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

While there likely are no platforms out there that mix generic and
legacy PHYs the driver should still be able to handle that, if only for
consistency reasons.

Add the missing calls to shutdown any legacy PHYs if generic PHY
initialisation fails.

Note that we continue to happily ignore potential errors from the legacy
PHY callbacks...
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-8-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use descriptive names consistently for the probe error labels.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-7-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The hibernation code is broken and has never been enabled in mainline
and should thus be dropped.

Specifically, the scratch buffer DMA mapping would have been leaked on
every suspend cycle since commit 51f5d49a ("usb: dwc3: core:
simplify suspend/resume operations") if this feature was ever enabled.

The related error handling was also broken and could have resulted in
attempts to unmap never mapped buffers, etc.

This effectively revert commit 0ffcaf37 ("usb: dwc3: core: allocate
scratch buffers").
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-6-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The hibernation code is broken and has never been enabled in mainline
and should thus be dropped.

Remove the hibernation bits from the gadget code, which effectively
reverts commits e1dadd3b ("usb: dwc3: workaround: bogus hibernation
events") and 7b2a0368 ("usb: dwc3: gadget: set KEEP_CONNECT in case
of hibernation") except for the spurious interrupt warning.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-5-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the missing calls to disable autosuspend on probe errors and on
driver unbind.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-4-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure to balance the runtime PM usage count on driver unbind by
adding back the pm_runtime_allow() call that had been erroneously
removed.

Fixes: 266d0493 ("usb: dwc3: core: don't trigger runtime pm when remove driver")
Cc: stable@vger.kernel.org	# 5.9
Cc: Li Jun <jun.li@nxp.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-3-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Make sure not to suspend the device when probe fails to avoid disabling
clocks and phys multiple times.

Fixes: 32808237 ("usb: dwc3: fix runtime PM in error path")
Cc: stable@vger.kernel.org      # 4.8
Cc: Roger Quadros <rogerq@ti.com>
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230404072524.19014-2-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It's needed on STM32MP15, when using the integrated full-speed PHY. This
clock is an output of USBPHYC, and the HS USBPHYC is not attached as PHY
in this case (managed directly by dwc2 ggpio glue):

    &usbotg_hs {
    	compatible = "st,stm32mp15-fsotg", "snps,dwc2";
    	pinctrl-names = "default";
    	pinctrl-0 = <&usbotg_hs_pins_a &usbotg_fs_dp_dm_pins_a>;
    	vbus-supply = <&vbus_otg>;
    	status = "okay";
    };

USBPHYC clock output must be used, so it can be properly enabled as a
clock provider.

Without this, currently, when the dualport High-Speed USBPHYC isn't
requested by either USBH or OTG, it remains uninitialized when probing
OTG: OTG configured with full-speed PHY isn't properly clocked, resulting
in error log like:
[    2.383138] dwc2 49000000.usb-otg: dwc2_core_reset: HANG! Soft Reset
timeout GRSTCTL_CSFTRST.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230414084137.1050487-5-fabrice.gasnier@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for the utmi clock. It's needed on STM32MP15, when using
the integrated full-speed PHY. This clock is an output of USBPHYC, but
HS USBPHYC is not attached as PHY in this case: Full-Speed PHY is directly
managed in dwc2 glue, through GGPIO register. Typical DT when using FS PHY
&usbotg_hs {
	compatible = "st,stm32mp15-fsotg", "snps,dwc2";
	pinctrl-names = "default";
	pinctrl-0 = <&usbotg_hs_pins_a &usbotg_fs_dp_dm_pins_a>;
	vbus-supply = <&vbus_otg>;
	status = "okay";
};

In this configuration, USBPHYC clock output must be defined, so it can
be properly enabled as a clock provider:
	clocks = <&rcc USBO_K>, <&usbphyc>;
	clock-names = "otg", "utmi";
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230414084137.1050487-4-fabrice.gasnier@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

utmi clock is typically provided by PHY output. Add this optional clock,
as the core could use other clocks depending on the SoC where it's used.
This is needed on stm32mp15, when using the integrated full-speed PHY.
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230414084137.1050487-3-fabrice.gasnier@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add error handling in __dwc2_lowlevel_hw_enable() that may leave the
clocks and regulators enabled upon error.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20230414084137.1050487-2-fabrice.gasnier@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add optional clock frmcnt_ck used on 4nm or advanced process SoC
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230407062406.12575-2-chunfeng.yun@mediatek.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add optional clock 'frmcnt_ck' used on 4nm or advanced process SoC
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/20230407062406.12575-1-chunfeng.yun@mediatek.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

For Realtek SoC, the usb xhci uses different driver for u2phy and u3phy.
Therefore, add a hook to retrieve the USB 3.0 PHY to XHCI plat.
Signed-off-by: Stanley Chang <stanley_chang@realtek.com>
Link: https://lore.kernel.org/r/20230407060731.20537-1-stanley_chang@realtek.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use common dev_is_pci() helper for checking PCI devices.
And if CONFIG_PCI is not defined, dev_is_pci returns false. Therefore,
CONFIG_PCI is also unnecessary, so remove it.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://lore.kernel.org/r/20230405234605.2310155-1-nobuhiro1.iwamatsu@toshiba.co.jpSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Wire up the debugfs regset device pointer so that the controller is
resumed before accessing registers to avoid crashing or locking up if it
happens to be runtime suspended.

Fixes: 02b6fdc2 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: stable@vger.kernel.org # 4.15: 30332eee: debugfs: regset32: Add Runtime PM support
Cc: stable@vger.kernel.org # 4.15
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20230405090342.7363-1-johan+linaro@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Several USB drivers use of_platform_* functions which are declared in
of_platform.h. of_platform.h gets implicitly included by of_device.h,
but that is going to be removed soon. Nothing else depends on of_device.h
so it can be dropped.
Acked-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230410232639.1561152-1-robh@kernel.orgSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The 'ret' variable in the function tegra_xudc_gadget_vbus_draw() is not
needed and so remove this variable.
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230405181854.42355-2-jonathanh@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit ac82b56b ("usb: gadget: tegra-xudc: Add vbus_draw support")
populated the vbus_draw callback for the Tegra XUDC driver. The function
tegra_xudc_gadget_vbus_draw(), that was added by this commit, assumes
that the pointer 'curr_usbphy' has been initialised, which is not always
the case because this is only initialised when the USB role is updated.
Fix this crash, by checking that the 'curr_usbphy' is valid before
dereferencing.

Fixes: ac82b56b ("usb: gadget: tegra-xudc: Add vbus_draw support")
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20230405181854.42355-1-jonathanh@nvidia.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Merge tag 'usb-serial-6.4-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next

Johan writes:

USB-serial updates for 6.4-rc1

Here are the USB-serial updates for 6.4-rc1; a new modem device id and
an unused-function cleanup.

All have been in linux-next with no reported issues.

* tag 'usb-serial-6.4-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: option: add UNISOC vendor and TOZED LT70C product
  USB: serial: quatech2: remove unused qt2_setdevice function

Merge tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt into usb-next

Mika writes:

thunderbolt: Changes for v6.4 merge window

This includes following Thunderbolt/USB4 changes for the v6.4 merge
window:

  - Refactoring of DROM read code paths
  - Convert to use SI units from units.h
  - A couple of cleanups

All these have been in linux-next with no reported issues.

* tag 'thunderbolt-for-v6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/westeri/thunderbolt:
  thunderbolt: Introduce usb4_port_sb_opcode_err_to_errno() helper
  thunderbolt: Make use of SI units from units.h
  thunderbolt: Get rid of redundant 'else'
  thunderbolt: Refactor DROM reading
  thunderbolt: use `tb_eeprom_get_drom_offset` to discover DROM offset

Add UNISOC vendor ID and TOZED LT70-C modem which is based from UNISOC
SL8563. The modem supports the NCM mode. Interface 0 is used for running
the AT commands. Interface 12 is the ADB interface.

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=1782 ProdID=4055 Rev=04.04
S:  Manufacturer=Unisoc Phone
S:  Product=Unisoc Phone
S:  SerialNumber=<redacted>
C:  #Ifs=14 Cfg#= 1 Atr=c0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0d Prot=00 Driver=cdc_ncm
E:  Ad=82(I) Atr=03(Int.) MxPS=  16 Ivl=32ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#=10 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=07(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8b(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#=11 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=08(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8c(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#=12 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)
E:  Ad=09(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8d(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#=13 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=0a(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 2 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0d Prot=00 Driver=cdc_ncm
E:  Ad=84(I) Atr=03(Int.) MxPS=  16 Ivl=32ms
I:  If#= 3 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 4 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0d Prot=00 Driver=cdc_ncm
E:  Ad=86(I) Atr=03(Int.) MxPS=  16 Ivl=32ms
I:  If#= 5 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 6 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0d Prot=00 Driver=cdc_ncm
E:  Ad=88(I) Atr=03(Int.) MxPS=  16 Ivl=32ms
I:  If#= 7 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=01 Driver=cdc_ncm
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 8 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=89(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:  If#= 9 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Link: https://lore.kernel.org/r/20230417152003.243248-1-arinc.unal@arinc9.com
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>

We need the USB fixes in here for testing, and this resolves two merge
conflicts, one pointed out by linux-next:

	drivers/usb/dwc3/dwc3-pci.c
	drivers/usb/host/xhci-pci.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull perf fixes from Borislav Petkov:

 - Fix "same task" check when redirecting event output

 - Do not wait unconditionally for RCU on the event migration path if
   there are no events to migrate

* tag 'perf_urgent_for_v6.3_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Fix the same task check in perf_event_set_output
  perf: Optimize perf_pmu_migrate_context()

Pull x86 fixes from Borislav Petkov:

 - Add a new Intel Arrow Lake CPU model number

 - Fix a confusion about how to check the version of the ACPI spec which
   supports a "online capable" bit in the MADT table which lead to a
   bunch of boot breakages with Zen1 systems and VMs

* tag 'x86_urgent_for_v6.3_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/cpu: Add model number for Intel Arrow Lake processor
  x86/acpi/boot: Correct acpi_is_processor_usable() check
  x86/ACPI/boot: Use FADT version to check support for online capable

Pull compute express link (cxl) fixes from Dan Williams:
 "Several fixes for driver startup regressions that landed during the
  merge window as well as some older bugs.

  The regressions were due to a lack of testing with what the CXL
  specification calls Restricted CXL Host (RCH) topologies compared to
  the testing with Virtual Host (VH) CXL topologies. A VH topology is
  typical PCIe while RCH topologies map CXL endpoints as Root Complex
  Integrated endpoints. The impact is some driver crashes on startup.

  This merge window also added compatibility for range registers (the
  mechanism that CXL 1.1 defined for mapping memory) to treat them like
  HDM decoders (the mechanism that CXL 2.0 defined for mapping
  Host-managed Device Memory). That work collided with the new region
  enumeration code that was tested with CXL 2.0 setups, and fails with
  crashes at startup.

  Lastly, the DOE (Data Object Exchange) implementation for retrieving
  an ACPI-like data table from CXL devices is being reworked for v6.4.
  Several fixes fell out of that work that are suitable for v6.3.

  All of this has been in linux-next for a while, and all reported
  issues [1] have been addressed.

  Summary:

   - Fix several issues with region enumeration in RCH topologies that
     can trigger crashes on driver startup or shutdown.

   - Fix CXL DVSEC range register compatibility versus region
     enumeration that leads to startup crashes

   - Fix CDAT endiannes handling

   - Fix multiple buffer handling boundary conditions

   - Fix Data Object Exchange (DOE) workqueue usage vs
     CONFIG_DEBUG_OBJECTS warn splats"

Link: http://lore.kernel.org/r/20230405075704.33de8121@canb.auug.org.au [1]

* tag 'cxl-fixes-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
  cxl/hdm: Extend DVSEC range register emulation for region enumeration
  cxl/hdm: Limit emulation to the number of range registers
  cxl/region: Move coherence tracking into cxl_region_attach()
  cxl/region: Fix region setup/teardown for RCDs
  cxl/port: Fix find_cxl_root() for RCDs and simplify it
  cxl/hdm: Skip emulation when driver manages mem_enable
  cxl/hdm: Fix double allocation of @cxlhdm
  PCI/DOE: Fix memory leak with CONFIG_DEBUG_OBJECTS=y
  PCI/DOE: Silence WARN splat with CONFIG_DEBUG_OBJECTS=y
  cxl/pci: Handle excessive CDAT length
  cxl/pci: Handle truncated CDAT entries
  cxl/pci: Handle truncated CDAT header
  cxl/pci: Fix CDAT retrieval on big endian

Pull cifs client fixes from Steve French:
 "Two cifs/smb3 client fixes, one for stable:

   - double lock fix for a cifs/smb1 reconnect path

   - DFS prefixpath fix for reconnect when server moved"

* tag '6.3-rc5-smb3-cifs-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
  cifs: double lock in cifs_reconnect_tcon()
  cifs: sanitize paths in cifs_update_super_prepath.

Pull char/misc driver fixes from Greg KH:
 "Here are a small set of various small driver changes for 6.3-rc6.
  Included in here are:

   - iio driver fixes for reported problems

   - coresight hwtracing bugfix for reported problem

   - small counter driver bugfixes

  All have been in linux-next for a while with no reported problems"

* tag 'char-misc-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  coresight: etm4x: Do not access TRCIDR1 for identification
  coresight-etm4: Fix for() loop drvdata->nr_addr_cmp range bug
  iio: adc: ti-ads7950: Set `can_sleep` flag for GPIO chip
  iio: adc: palmas_gpadc: fix NULL dereference on rmmod
  counter: 104-quad-8: Fix Synapse action reported for Index signals
  counter: 104-quad-8: Fix race condition between FLAG and CNTR reads
  iio: adc: max11410: fix read_poll_timeout() usage
  iio: dac: cio-dac: Fix max DAC write value check for 12-bit
  iio: light: cm32181: Unregister second I2C client if present
  iio: accel: kionix-kx022a: Get the timestamp from the driver's private data in the trigger_handler
  iio: adc: ad7791: fix IRQ flags
  iio: buffer: make sure O_NONBLOCK is respected
  iio: buffer: correctly return bytes written in output buffers
  iio: light: vcnl4000: Fix WARN_ON on uninitialized lock
  iio: adis16480: select CONFIG_CRC32
  drivers: iio: adc: ltc2497: fix LSB shift
  iio: adc: qcom-spmi-adc5: Fix the channel name

Pull tty/serial driver fixes from Greg KH:
 "Here are some small tty and serial driver fixes for some reported
  problems:

   - fsl_uart driver bugfixes

   - sh-sci serial driver bugfixes

   - renesas serial driver DT binding bugfixes

   - 8250 DMA bugfix

  All of these have been in linux-next for a while with no reported
  problems"

* tag 'tty-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  tty: serial: sh-sci: Fix Rx on RZ/G2L SCI
  tty: serial: fsl_lpuart: fix crash in lpuart_uport_is_active
  tty: serial: fsl_lpuart: avoid checking for transfer complete when UARTCTRL_SBK is asserted in lpuart32_tx_empty
  serial: 8250: Prevent starting up DMA Rx on THRI interrupt
  dt-bindings: serial: renesas,scif: Fix 4th IRQ for 4-IRQ SCIFs
  tty: serial: sh-sci: Fix transmit end interrupt handler

Pull USB bugfixes from Greg KH:
 "Here are some small USB bugfixes for 6.3-rc6 that have been in my
  tree, and in linux-next, for a while. Included in here are:

   - new usb-serial driver device ids

   - xhci bugfixes for reported problems

   - gadget driver bugfixes for reported problems

   - dwc3 new device id

  All have been in linux-next with no reported problems"

* tag 'usb-6.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: cdnsp: Fixes error: uninitialized symbol 'len'
  usb: gadgetfs: Fix ep_read_iter to handle ITER_UBUF
  usb: gadget: f_fs: Fix ffs_epfile_read_iter to handle ITER_UBUF
  usb: typec: altmodes/displayport: Fix configure initial pin assignment
  usb: dwc3: pci: add support for the Intel Meteor Lake-S
  xhci: Free the command allocated for setting LPM if we return early
  Revert "usb: xhci-pci: Set PROBE_PREFER_ASYNCHRONOUS"
  xhci: also avoid the XHCI_ZERO_64B_REGS quirk with a passthrough iommu
  USB: serial: option: add Quectel RM500U-CN modem
  usb: xhci: tegra: fix sleep in atomic call
  USB: serial: option: add Telit FE990 compositions
  USB: serial: cp210x: add Silicon Labs IFS-USB-DATACABLE IDs

Pull SCSI fixes from James Bottomley:
 "Four small fixes, all in drivers. They're all one or two lines except
  for the ufs one, but that's a simple revert of a previous feature"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: iscsi_tcp: Check that sock is valid before iscsi_set_param()
  scsi: qla2xxx: Fix memory leak in qla2x00_probe_one()
  scsi: mpi3mr: Handle soft reset in progress fault code (0xF002)
  scsi: Revert "scsi: ufs: core: Initialize devfreq synchronously"

Pull block fixes from Jens Axboe:

 - Ensure that ublk always reads the whole sqe upfront (me)

 - Fix for a block size probing issue with ublk (Ming)

 - Fix for the bio based polling (Keith)

 - NVMe pull request via Christoph:
      - fix discard support without oncs (Keith Busch)

 - Partition scan error handling regression fix (Yu)

* tag 'block-6.3-2023-04-06' of git://git.kernel.dk/linux:
  block: don't set GD_NEED_PART_SCAN if scan partition failed
  block: ublk: make sure that block size is set correctly
  ublk: read any SQE values upfront
  nvme: fix discard support without oncs
  blk-mq: directly poll requests

Pull io_uring fixes from Jens Axboe:
 "Just two minor fixes for provided buffers - one where we could
  potentially leak a buffer, and one where the returned values was
  off-by-one in some cases"

* tag 'io_uring-6.3-2023-04-06' of git://git.kernel.dk/linux:
  io_uring: fix memory leak when removing provided buffers
  io_uring: fix return value when removing provided buffers

Pull dma-mapping fix from Christoph Hellwig:

 - fix a braino in the swiotlb alignment check fix (Petr Tesarik)

* tag 'dma-mapping-6.3-2023-04-08' of git://git.infradead.org/users/hch/dma-mapping:
  swiotlb: fix a braino in the alignment check fix