Merge branch 'for_3.4/gpio/runtime-pm-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into gpio/next

pl061 uses same routines for suspend/freeze/poweroff and resume/thaw/restore.
We are only saving and restoring register values on these routines.

During hibernation, in freeze() we take a snapshot of gpio registers. In thaw()
we don't actually need to restore these registers, as power was never shut down
till now. Similarly, in poweroff() we don't need to take snapshot of these
registers again, as it was done during freeze() and by now the image is already
saved on disk.

This patch passes poweroff() and thaw() routines as NULL to avoid this extra
work done.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

Hi,

On Wed, Feb 8, 2012 at 8:41 PM, Felipe Balbi <balbi@ti.com> wrote:
> Hi guys,
>
> I have just triggered the folllowing:
>
> [   84.860321] ======================================================
> [   84.860321] [ INFO: possible circular locking dependency detected ]
> [   84.860321] 3.3.0-rc2-00026-ge4e8a39 #474 Not tainted
> [   84.860321] -------------------------------------------------------
> [   84.860321] bash/949 is trying to acquire lock:
> [   84.860321]  (sysfs_lock){+.+.+.}, at: [<c0275358>] gpio_value_store+0x24/0xcc
> [   84.860321]
> [   84.860321] but task is already holding lock:
> [   84.860321]  (s_active#22){++++.+}, at: [<c016996c>] sysfs_write_file+0xdc/0x184
> [   84.911468]
> [   84.911468] which lock already depends on the new lock.
> [   84.911468]
> [   84.920043]
> [   84.920043] the existing dependency chain (in reverse order) is:
> [   84.920043]
> [   84.927886] -> #1 (s_active#22){++++.+}:
> [   84.927886]        [<c008f640>] check_prevs_add+0xdc/0x150
> [   84.927886]        [<c008fc18>] validate_chain.clone.24+0x564/0x694
> [   84.927886]        [<c0090cdc>] __lock_acquire+0x49c/0x980
> [   84.951660]        [<c0091838>] lock_acquire+0x98/0x100
> [   84.951660]        [<c016a8e8>] sysfs_deactivate+0xb0/0x100
> [   84.962982]        [<c016b1b4>] sysfs_addrm_finish+0x2c/0x6c
> [   84.962982]        [<c016b8bc>] sysfs_remove_dir+0x84/0x98
> [   84.962982]        [<c02590d8>] kobject_del+0x10/0x78
> [   84.974670]        [<c02c29e8>] device_del+0x140/0x170
> [   84.974670]        [<c02c2a24>] device_unregister+0xc/0x18
> [   84.985382]        [<c0276894>] gpio_unexport+0xbc/0xdc
> [   84.985382]        [<c02768c8>] gpio_free+0x14/0xfc
> [   85.001708]        [<c0276a28>] unexport_store+0x78/0x8c
> [   85.001708]        [<c02c5af8>] class_attr_store+0x18/0x24
> [   85.007293]        [<c0169990>] sysfs_write_file+0x100/0x184
> [   85.018981]        [<c0109d48>] vfs_write+0xb4/0x148
> [   85.018981]        [<c0109fd0>] sys_write+0x40/0x70
> [   85.018981]        [<c0013cc0>] ret_fast_syscall+0x0/0x3c
> [   85.035003]
> [   85.035003] -> #0 (sysfs_lock){+.+.+.}:
> [   85.035003]        [<c008f54c>] check_prev_add+0x680/0x698
> [   85.035003]        [<c008f640>] check_prevs_add+0xdc/0x150
> [   85.052093]        [<c008fc18>] validate_chain.clone.24+0x564/0x694
> [   85.052093]        [<c0090cdc>] __lock_acquire+0x49c/0x980
> [   85.052093]        [<c0091838>] lock_acquire+0x98/0x100
> [   85.069885]        [<c047e280>] mutex_lock_nested+0x3c/0x2f4
> [   85.069885]        [<c0275358>] gpio_value_store+0x24/0xcc
> [   85.069885]        [<c02c18dc>] dev_attr_store+0x18/0x24
> [   85.087158]        [<c0169990>] sysfs_write_file+0x100/0x184
> [   85.087158]        [<c0109d48>] vfs_write+0xb4/0x148
> [   85.098297]        [<c0109fd0>] sys_write+0x40/0x70
> [   85.098297]        [<c0013cc0>] ret_fast_syscall+0x0/0x3c
> [   85.109069]
> [   85.109069] other info that might help us debug this:
> [   85.109069]
> [   85.117462]  Possible unsafe locking scenario:
> [   85.117462]
> [   85.117462]        CPU0                    CPU1
> [   85.128417]        ----                    ----
> [   85.128417]   lock(s_active#22);
> [   85.128417]                                lock(sysfs_lock);
> [   85.128417]                                lock(s_active#22);
> [   85.142486]   lock(sysfs_lock);
> [   85.151794]
> [   85.151794]  *** DEADLOCK ***
> [   85.151794]
> [   85.151794] 2 locks held by bash/949:
> [   85.158020]  #0:  (&buffer->mutex){+.+.+.}, at: [<c01698b8>] sysfs_write_file+0x28/0x184
> [   85.170349]  #1:  (s_active#22){++++.+}, at: [<c016996c>] sysfs_write_file+0xdc/0x184
> [   85.170349]
> [   85.178588] stack backtrace:
> [   85.178588] [<c001b824>] (unwind_backtrace+0x0/0xf0) from [<c008de64>] (print_circular_bug+0x100/0x114)
> [   85.193023] [<c008de64>] (print_circular_bug+0x100/0x114) from [<c008f54c>] (check_prev_add+0x680/0x698)
> [   85.193023] [<c008f54c>] (check_prev_add+0x680/0x698) from [<c008f640>] (check_prevs_add+0xdc/0x150)
> [   85.212524] [<c008f640>] (check_prevs_add+0xdc/0x150) from [<c008fc18>] (validate_chain.clone.24+0x564/0x694)
> [   85.212524] [<c008fc18>] (validate_chain.clone.24+0x564/0x694) from [<c0090cdc>] (__lock_acquire+0x49c/0x980)
> [   85.233306] [<c0090cdc>] (__lock_acquire+0x49c/0x980) from [<c0091838>] (lock_acquire+0x98/0x100)
> [   85.233306] [<c0091838>] (lock_acquire+0x98/0x100) from [<c047e280>] (mutex_lock_nested+0x3c/0x2f4)
> [   85.242614] [<c047e280>] (mutex_lock_nested+0x3c/0x2f4) from [<c0275358>] (gpio_value_store+0x24/0xcc)
> [   85.261840] [<c0275358>] (gpio_value_store+0x24/0xcc) from [<c02c18dc>] (dev_attr_store+0x18/0x24)
> [   85.261840] [<c02c18dc>] (dev_attr_store+0x18/0x24) from [<c0169990>] (sysfs_write_file+0x100/0x184)
> [   85.271240] [<c0169990>] (sysfs_write_file+0x100/0x184) from [<c0109d48>] (vfs_write+0xb4/0x148)
> [   85.290008] [<c0109d48>] (vfs_write+0xb4/0x148) from [<c0109fd0>] (sys_write+0x40/0x70)
> [   85.298400] [<c0109fd0>] (sys_write+0x40/0x70) from [<c0013cc0>] (ret_fast_syscall+0x0/0x3c)
> -bash: echo: write error: Operation not permitted
>
> the way to trigger is:
>
> root@legolas:~# cd /sys/class/gpio/
> root@legolas:/sys/class/gpio# echo 2 > export
> root@legolas:/sys/class/gpio# echo 2 > unexport
> root@legolas:/sys/class/gpio# echo 2 > export
> root@legolas:/sys/class/gpio# cd gpio2/
> root@legolas:/sys/class/gpio/gpio2# echo 1 > value

Looks 'sysfs_lock' needn't to be held for unregister, so the patch below may
fix the problem.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

GPIO IP revisions such as those used in OMAP4 have a set_dataout
while the previous revisions used a single dataout register.
Depending on what is available restore the dataout settings
to the right register.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Setup the dataout register before restoring OE. This is to make
sure that we have valid data in dataout register which would be
made available in output pins as soon as OE is enabled. Else,
there is risk of unknown data getting out into gpio pins.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Setup the interrupt enable registers only after we have configured the
required edge and required configurations, not before, to prevent
spurious events as part of restore routine.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

GPIO debounce registers need to be saved and restored for proper functioning
of driver.
Signed-off-by: Nishanth Menon <nm@ti.com>
tarun.kanti@ti.com: Debounce context save is moved to _set_gpio_debounce()
as part of dynamic context save to remove overhead.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Context is now saved dynamically in respective functions whenever and
whichever registers are modified. This avoid overhead of saving all
registers context in the runtime suspend callback.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Enable debounce clock before writing/reading debounce registers.
Disable the clock at the end so that it is synchronized with the
pm_runtime_get/put_sync calls.

Enable debounce clock per module. This call is mandatory because
in omap_gpio_request() when *_runtime_get_sync() is called,
_gpio_dbck_enable() within runtime callbck fails to turn on dbck
 because dbck_enable_mask used within _gpio_dbck_enable() is still
not initialized at that point. Therefore we have to enable dbck here.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

The dbck_enable_mask indicates which all GPIOs within a bank have debounce
enabled and dbck is enabled/disabled based upon this. But there is no
mechanism to track the dbck state. In order to manage the dbck state we need
additional flag and logic so that turning off/on dbck is synchronized with
pm_runtime_put/get_sync calls.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Since *_prepare_for_idle() and *_resume_after_idle() are called
with interrupts disabled they should be kept as simple as possible.
So, moving most of the stuff to *_runtime_suspend/resume() callbacks.

To avoid invalid context restore happening in *_runtime_resume()
callback as a result of *_get_sync() call in *_gpio_probe(), update
bank->context_loss_count. This would make context restore condition
check false in the callback and skip restore until further
initialization take place. The workaround_enabled static variable
is now a member of struct gpio_bank.

Unlike most GPIO registers the OE has 0xffffffff as the default value.
To make sure invalid context is not restored, updating the OE context
with default value.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

There is no need to operate on all the banks every time the function is called.
Just operate on the current bank passed by the framework.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Call runtime pm APIs pm_runtime_get_sync() and pm_runtime_put()
for enabling/disabling clocks appropriately. Remove syscore_ops and
instead use SET_RUNTIME_PM_OPS macro.

There is no more need to call omap_device_disable_idle_on_suspend
since driver is PM runtime adapted now.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

In all OMAP1 SoCs, the MPUIO bank width is 16 bits. But, in OMAP7xx,
it is wrongly initialised to 32. Fix this.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

The only bank->type (method) used in the OMAP GPIO driver is MPUIO type as they
need to be handled separately. Identify the same using a flag and remove all
METHOD_* macros.

mpuio_init() function is defined under #ifdefs. It is required only in case
of MPUIO bank type and only when PM operations are supported by it.
This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
For all the other cases it is a dummy function. Hence clean up the same
and remove all the OMAP SoC specific #ifdefs.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Remove un-necessary bit masking. Since the register are 4 byte aligned
and readl would work as is. The 'enabled' mask is already taking care
to mask for bank width.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Use regs->pinctrl field instead of using the macro OMAP1510_GPIO_PIN_CONTROL
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

With register offsets now defined for respective OMAP versions we can get rid
of cpu_class_* checks. This function now has common initialization code for
all OMAP versions. Initialization specific to OMAP16xx has been moved within
omap16xx_gpio_init().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Getting rid of ifdefs within the function by adding register offset intctrl
and associating OMAPXXXX_GPIO_INT_CONTROL in respective SoC specific files.
Also, use wkup_status register consistently instead of referring to wakeup
clear and wakeup set register offsets. Get rid of cpu_is_xxxx checks in
set_gpio_trigger() using irqctrl.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

It is not required to use hard-coded offsets any more in context save and
restore functions and instead use the generic offsets which have been correctly
initialized during device registration.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

By adding level and edge detection register offsets and then initializing them
correctly according to OMAP versions during device registrations we can now remove
lot of revision checks in these functions.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Wakeup enable register offset initialized according to OMAP versions
during device registration. Use this to avoid version checks.
Starting with OMAP4, legacy registers should not be used in combination
with the updated regsiters. Use wkup_en register consistently for
all SoCs wherever applicable.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Remove cpu-is checks while enabling/disabling OMAP GPIO module during a gpio
request/free.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Non-wakeup GPIOs are available only in OMAP2. Avoid cpu_is checks by making
non_wakeup_gpios as part of pdata.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Modify omap_gpio_prepare_for_idle() & omap_gpio_resume_after_idle() functions
to handle save context & restore context respectively in the OMAP GPIO driver
itself instead of calling these functions from pm specific files.
For this, in gpio_prepare_for_idle(), call *_get_context_loss_count() and in
gpio_resume_after_idle() call it again. If the count is different, do restore
context.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Currently gpio_context array used to save gpio bank's context, is used only for
OMAP3 architecture. Move gpio_context as part of gpio_bank structure so that it
can be specific to each gpio bank and can be used for any OMAP architecture
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

In omap3, save/restore context is implemented for GPIO banks 2-6 as GPIO bank1
is in wakeup domain. Instead of identifying bank's power domain by bank id,
use 'loses_context' flag which is filled by pwrdm_can_ever_lose_context()
during dev_init.

For getting the powerdomain pointer, omap_hwmod_get_pwrdm() is used.
omap_device_get_pwrdm() could not be used as the pwrdm information needs to be
filled in pdata, whereas omap_device_get_pwrdm() could be used only after
omap_device_build() call.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

The gpio_bank_count is the count of number of GPIO devices in a SoC. Remove this
dependency from the driver by using list. Also remove the dependency on array of
pointers to gpio_bank struct of all GPIO devices.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

The device tps65910/tps65911 supports the sleep
functionality in some of gpios. If gpio is configured
in output mode and sleep is enabled then during device
sleep state, the output of gpio becomes LOW regardless
of non-sleep output value.
Such gpio can be used to control regulator switch such
that output of regulator is off in device sleep state.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>

Sodaville has GPIO controller behind the PCI bus. To my suprissed it is
not the same as on PXA.

The interrupt & gpio chip can be referenced from the device tree like
from any other driver. Unfortunately the driver which uses the gpio
interrupt has to use irq_of_parse_and_map() instead of
platform_get_irq(). The problem is that the platform device (which is
created from the device tree) is most likely created before the
interrupt chip is registered and therefore irq_of_parse_and_map() fails.

In theory the driver works as module. In reality most of the irq
functions are not exported to modules and it is possible that _this_
module is unloaded while the provided irqs are still in use.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
[torbenh@linutronix.de: make it work after the irq namespace cleanup,
	                add some device tree entries.]
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
[bigeasy@linutronix.de: convert to generic irq & gpio chip]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[grant.likely@secretlab.ca: depend on x86 to avoid irq_domain breakage]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>

There are few important bug fixes for LogFS

* tag 'for-linus' of git://github.com/prasad-joshi/logfs_upstream:
  Logfs: Allow NULL block_isbad() methods
  logfs: Grow inode in delete path
  logfs: Free areas before calling generic_shutdown_super()
  logfs: remove useless BUG_ON
  MAINTAINERS: Add Prasad Joshi in LogFS maintiners
  logfs: Propagate page parameter to __logfs_write_inode
  logfs: set superblock shutdown flag after generic sb shutdown
  logfs: take write mutex lock during fsync and sync
  logfs: Prevent memory corruption
  logfs: update page reference count for pined pages

Fix up conflict in fs/logfs/dev_mtd.c due to semantic change in what
"mtd->block_isbad" means in commit f2933e86: "Logfs: Allow NULL
block_isbad() methods" clashing with the abstraction changes in the
commits 7086c19d: "mtd: introduce mtd_block_isbad interface" and
d58b27ed: "logfs: do not use 'mtd->block_isbad' directly".

This resolution takes the semantics from commit f2933e86, and just
makes mtd_block_isbad() return zero (false) if the 'block_isbad'
function is NULL.  But that also means that now "mtd_can_have_bb()"
always returns 0.

Now, "mtd_block_markbad()" will obviously return an error if the
low-level driver doesn't support bad blocks, so this is somewhat
non-symmetric, but it actually makes sense if a NULL "block_isbad"
function is considered to mean "I assume that all my blocks are always
good".

Merge branch 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (w83627ehf) Disable setting DC mode for pwm2, pwm3 on NCT6776F
  hwmon: (sht15) fix bad error code
  MAINTAINERS: Drop maintainer for MAX1668 hwmon driver
  MAINTAINERS: Add hwmon entries for Wolfson
  hwmon: (f71805f) Fix clamping of temperature limits

Here are some fixes to the pin control system that has accumulated since
-rc1.  Mainly Tony Lindgren fixed the module load/unload logic and the
rest are minor fixes and documentation.

* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: add checks for empty function names
  pinctrl: fix pinmux_hog_maps when ctrl_dev_name is not set
  pinctrl: fix some pinmux typos
  pinctrl: free debugfs entries when unloading a pinmux driver
  pinctrl: unbreak error messages
  Documentation/pinctrl: fix a few syntax errors in code examples
  pinctrl: fix pinconf_pins_show iteration

Here are some tty/serial patches for 3.3-rc1

Big thing here is the movement of the 8250 serial drivers to their own
directory, now that the patch churn has calmed down.

Other than that, only minor stuff (omap patches were reverted as they
were found to be wrong), and another broken driver removed from the
system.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* tag 'tty-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  serial: Kill off Moorestown code
  Revert "tty: serial: OMAP: ensure FIFO levels are set correctly in non-DMA mode"
  Revert "tty: serial: OMAP: transmit FIFO threshold interrupts don't wake the chip"
  serial: Fix wakeup init logic to speed up startup
  docbook: don't use serial_core.h in device-drivers book
  serial: amba-pl011: lock console writes against interrupts
  amba-pl011: do not disable RTS during shutdown
  tty: serial: OMAP: transmit FIFO threshold interrupts don't wake the chip
  tty: serial: OMAP: ensure FIFO levels are set correctly in non-DMA mode
  omap-serial: make serial_omap_restore_context depend on CONFIG_PM_RUNTIME
  omap-serial :Make the suspend/resume functions depend on CONFIG_PM_SLEEP.
  TTY: fix UV serial console regression
  jsm: Fixed EEH recovery error
  Updated TTY MAINTAINERS info
  serial: group all the 8250 related code together

Here are a bunch of USB patches for 3.3-rc1.

Nothing major, largest thing here is the removal of some drivers that
did not work at all.  Other than that, the normal collection of bugfixes
and new device ids.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* tag 'usb-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (52 commits)
  uwb & wusb: fix kconfig error
  USB: Realtek cr: fix autopm scheduling while atomic
  USB: ftdi_sio: Add more identifiers
  xHCI: Cleanup isoc transfer ring when TD length mismatch found
  usb: musb: omap2430: minor cleanups.
  qcaux: add more Pantech UML190 and UML290 ports
  Revert "drivers: usb: Fix dependency for USB_HWA_HCD"
  usb: mv-otg - Fix build if CONFIG_USB is not set
  USB: cdc-wdm: Avoid hanging on interface with no USB_CDC_DMM_TYPE
  usb: add support for STA2X11 host driver
  drivers: usb: Fix dependency for USB_HWA_HCD
  kernel-doc: fix new warning in usb.h
  USB: OHCI: fix new compiler warnings
  usb: serial: kobil_sct: fix compile warning:
  drivers/usb/host/ehci-fsl.c: add missing iounmap
  USB: cdc-wdm: better allocate a buffer that is at least as big as we tell the USB core
  USB: cdc-wdm: call wake_up_all to allow driver to shutdown on device removal
  USB: cdc-wdm: use two mutexes to allow simultaneous read and write
  USB: cdc-wdm: updating desc->length must be protected by spin_lock
  USB: usbsevseg: fix max length
  ...

1) Setting link attributes can modify the size of the attributes that
   would be reported on a subsequent getlink netlink operation,
   therefore min_ifinfo_dump_size needs to be adjusted.  From Stefan
   Gula.

2) Resegmentation of TSO frames while trimming can violate invariants
   expected by callers, namely that the number of segments can only stay
   the same or decrease, never increase.  If MSS changes, however, we
   can trim data but then end up with more segments.  Fix this by only
   segmenting to the MSS already recorded in the SKB.  That's the
   simplest fix for now and if we want to get more fancy in the future
   that's a more involved change.

   This probably explains some retransmit counter inaccuracies.

   From Neal Cardwell.

3) Fix too-many-wakeups in POLL with AF_UNIX sockets, from Eric Dumazet.

4) Fix CAIF crashes wrt.  namespace handling.  From Eric Dumazet and
   Eric W. Biederman.

5) TCP port selection fixes from Flavio Leitner.

6) More socket memory cgroup build fixes in certain randonfig
   situations.  From Glauber Costa.

7) Fix TCP memory sysctl regression reported by Ingo Molnar, also from
   Glauber Costa.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  af_unix: fix EPOLLET regression for stream sockets
  tcp: fix tcp_trim_head() to adjust segment count with skb MSS
  net/tcp: Fix tcp memory limits initialization when !CONFIG_SYSCTL
  net caif: Register properly as a pernet subsystem.
  netns: Fail conspicously if someone uses net_generic at an inappropriate time.
  net: explicitly add jump_label.h header to sock.h
  net: RTNETLINK adjusting values of min_ifinfo_dump_size
  ipv6: Fix ip_gre lockless xmits.
  xen-netfront: correct MAX_TX_TARGET calculation.
  netns: fix net_alloc_generic()
  tcp: bind() optimize port allocation
  tcp: bind() fix autoselection to share ports
  l2tp: l2tp_ip - fix possible oops on packet receive
  iwlwifi: fix PCI-E transport "inta" race
  mac80211: set bss_conf.idle when vif is connected
  mac80211: update oper_channel on ibss join

This fixes an integration issue with the regulator device tree bindings
which shook out in -rc.  The bindings were overly enthusiatic when
deciding to set a voltage on a regulator and would try to set zero volts
on an unconfigured regulator which isn't supported.

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: Set apply_uV only when min and max voltages are defined

Commit 0884d7aa (AF_UNIX: Fix poll blocking problem when reading from
a stream socket) added a regression for epoll() in Edge Triggered mode
(EPOLLET)

Appropriate fix is to use skb_peek()/skb_unlink() instead of
skb_dequeue(), and only call skb_unlink() when skb is fully consumed.

This remove the need to requeue a partial skb into sk_receive_queue head
and the extra sk->sk_data_ready() calls that added the regression.

This is safe because once skb is given to sk_receive_queue, it is not
modified by a writer, and readers are serialized by u->readlock mutex.

This also reduce number of spinlock acquisition for small reads or
MSG_PEEK users so should improve overall performance.
Reported-by: Nick Mathewson <nickm@freehaven.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Alexey Moiseytsev <himeraster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>