This is a specific implementation, <asm/unaligned.h> is the
multiplexer that has the arch-specific knowledge of which
of the implementations needs to be used, so include that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When an NFC-DEP target receives an ATN PDU, its
supposed to respond with a similar ATN PDU.
When the Target receives an I PDU with the PNI
one less than the current PNI and the last PDU
sent was an ATN PDU, the Target is to resend the
last non-ATN PDU that it has sent.  This is
described in section 14.12.3.4 of the NFC Digital
Protocol Spec.

The digital layer's NFC-DEP code doesn't implement
this so add that support.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When an NFC-DEP Initiator times out when waiting for
a DEP_RES from the Target, its supposed to send an
ATN to the Target.  The Target should respond to the
ATN with a similar ATN PDU and the Initiator can then
resend the last non-ATN PDU that it sent.  No more
than 'N(retry,atn)' are to be send where
2 <= 'N(retry,atn)' <= 5.  If the Initiator had just
sent a NACK PDU when the timeout occurred, it is to
continue sending NACKs until 'N(retry,nack)' NACKs
have been send.  This is described in section
14.12.5.6 of the NFC-DEP Digital Protocol Spec.

The digital layer's NFC-DEP code doesn't implement
this so add that support.

The value chosen for 'N(retry,atn)' is 2.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When an NFC-DEP Target receives a NACK PDU with
a PNI equal to 1 less than the current PNI, it
is supposed to re-send the last PDU.  This is
implied in section 14.12.5.4 of the NFC Digital
Protocol Spec.

The digital layer's NFC-DEP code doesn't implement
Target-side NACK handing so add it.  The last PDU
that was sent is saved in the 'nfc_digital_dev'
structure's 'saved_skb' member.  The skb will have
an additional reference taken to ensure that the skb
isn't freed when the driver performs a kfree_skb()
on the skb.  The length of the skb/PDU is also saved
so the length can be restored when re-sending the PDU
in the skb (the driver will perform an skb_pull() so
an skb_push() needs to be done to restore the skb's
data pointer/length).
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When an NFC-DEP Initiator receives a frame with
an incorrect CRC or with a parity error, and the
frame is at least 4 bytes long, its supposed to
send a NACK to the Target.  The Initiator can
send up to 'N(retry,nack)' consecutive NACKs
where 2 <= 'N(retry,nack)' <= 5.  When the limit
is exceeded, a PROTOCOL EXCEPTION is raised.
Any other type of transmission error is to be
ignored and the Initiator should continue
waiting for a new frame.  This is described
in section 14.12.5.4 of the NFC Digital Protocol
Spec.

The digital layer's NFC-DEP code doesn't implement
any of this so add it.  This support diverges from
the spec in two significant ways:

a) NACKs will be sent for ANY error reported by the
   driver except a timeout.  This is done because
   there is currently no way for the digital layer
   to distinguish a CRC or parity error from any
   other type of error reported by the driver.

b) All other errors will cause a PROTOCOL EXCEPTION
   even frames with CRC errors that are less than 4
   bytes.

The value chosen for 'N(retry,nack)' is 2.

Targets do not send NACK PDUs.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When the peer in an NFC-DEP exchange has a
packet to send that is larger than the local
maximum payload, it sets the 'MI' bit in the
'I' PDU.  This indicates that NFC-DEP chaining
is to occur.

When such a PDU is received, the local side
responds with an 'ACK' PDU and this continues
until the peer sends an 'I' PDU with the 'MI'
bit cleared.  This indicates that the chaining
sequence is complete and the entire packet has
been transferred.

Receiving chained PDUs is currently not supported
by the digital layer so add that support.  When a
chaining sequence is initiated by the peer, the
digital layer will allocate an skb large enough
to hold 8 maximum sized frame payloads.  The maximum
payload can range from 64 to 254 bytes so 8 * 254 =
2032 seems like a reasonable compromise between
potentially wasting memory and constantly reallocating
new, larger skbs.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When the NFC-DEP code is given a packet to send
that is larger than the peer's maximum payload,
its supposed to set the 'MI' bit in the 'I' PDU's
Protocol Frame Byte (PFB).  Setting this bit
indicates that NFC-DEP chaining is to occur.

When NFC-DEP chaining is progress, sender 'I' PDUs
are acknowledged with 'ACK' PDUs until the last 'I'
PDU in the chain (which has the 'MI' bit cleared)
is responded to with a normal 'I' PDU.  This can
occur while in Initiator mode or in Target mode.

Sender NFC-DEP chaining is currently not implemented
in the digital layer so add that support.  Unfortunately,
since sending a frame may require writing the CRC to the
end of the data, the relevant data part of the original
skb must be copied for each intermediate frame.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The maximum payload for NFC-DEP exchanges (i.e., the
number of bytes between SoD and EoD) is negotiated
using the ATR_REQ, ATR_RES, and PSL_REQ commands.
The valid maximum lengths are 64, 128, 192, and 254
bytes.

Currently, NFC-DEP code assumes that both sides are
always using 254 byte maximums and ignores attempts
by the peer to change it.  Instead, implement the
negotiation code, enforce the local maximum when
receiving data from the peer, and don't send payloads
that exceed the remote's maximum.  The default local
maximum is 254 bytes.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

NFC-DEP DEP_REQ and DEP_RES exchanges using 'I'
and 'ACK/NACK' PDUs have a sequence number called
the Packet Number Information (PNI).  The PNI
is incremented (modulo 4) after every DEP_REQ/
DEP_RES pair and should be verified by the digital
layer code.  That verification isn't always done,
though, so add code to make sure that it is done.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

According to chapter 14 of the NFC-DEP Digital
Protocol Spec., the NAD byte should never be
present in DEP_REQ or DEP_RES frames.  However,
this is not enforced so add that enforcement code.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When in Target mode, the Initiator specifies whether
subsequent DEP_REQ and DEP_RES frames will include
a DID byte by the value passed in the ATR_REQ.  If
the DID value in the ATR_REQ is '0' then no DID
byte will be included.  If the DID value is between
'1' and '14' then a DID byte containing the same
value must be included in subsequent DEP_REQ and
DEP_RES frames.  Any other DID value is invalid.
This is specified in sections 14.8.1.2 and 14.8.2.2
of the NFC Digital Protocol Spec.

Checking the DID value (if it should be there at all),
is not currently supported by the digital layer's
NFC-DEP code.  Add this support by remembering the
DID value in the ATR_REQ, checking the DID value of
received DEP_REQ frames (if it should be there at all),
and including the remembered DID value in DEP_RES
frames when appropriate.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When in Initiator mode, the digital layer's
NFC-DEP code always sets the Device ID (DID)
value in the ATR_REQ to '0'.  This means that
subsequent DEP_REQ and DEP_RES frames must
never include a DID byte.  This is specified
in sections 14.8.1.1 and 14.8.2.1 of the NFC
Digital Protocol Spec.

Currently, the digital layer's NFC-DEP code
doesn't enforce this rule so add code to ensure
that there is no DID byte in DEP_RES frames.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Rearrange some of the code in digital_in_recv_dep_res()
and digital_tg_recv_dep_req() so the initial code looks
similar.  The real reason is prepare the code for some
upcoming patches that require these changes.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

When digital_in_send_cmd() or digital_tg_send_cmd()
fail, they do not free the skb that was passed to
them so the routine that allocated the skb should
free it.  Currently, there are several routines in
the NFC-DEP code that don't do this so make them.
Reviewed-by: Thierry Escande <thierry.escande@linux.intel.com>
Tested-by: Thierry Escande <thierry.escande@linux.intel.com>
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

ACK status (0/1) for ACTION frames is informed to cfg80211. We
will extend existing logic used for EAPOL frames. The cfg80211
API is different here. Also, we need to explicitly free cloned
skb.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Firmware notifies the driver through event if EAPOL data packet
has been acked or not. We will inform this status to userspace
listening on a socket.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

We had introduced delay main work logic to avoid processing
interrupts when Rx pending packet count reaches high threshold.
interrupt processing is restarted later when packet count
reduces lower threashold. This helped to reduce unnecessary
overhead and improve throughput for SD and PCIe chipsets.

As there are no interrupts for USB, we will skip this logic for
USB chipsets.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch adds missing endian conversion for beacon size while
processing scan response.
Reported-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Tested-by: Daniel Mosquera <daniel.mosquera@ctag.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes following sparse warnings:

drivers/net/wireless/mwifiex/util.c:152:19: warning: cast from restricted __le16
drivers/net/wireless/mwifiex/util.c:152:19: warning: restricted __le16 degrades to integer
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add TPC capability to TX descriptor path. Cap per-packet TX power according to
TX power per-rate tables. Currently TPC is supported just by AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add TX power per-rate tables for different MIMO modes (e.g STBC) in order to
cap the maximum TX power value per-rate in the TX descriptor path.
Cap TX power for self generated frames (ACK, RTS/CTS).
Currently TPC is supported just by AR9003 based chips
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When the driver has sent a join iovar to the firmware it waits
for the events to report result of the connection. However, the
wpa_supplicant will request a .disconnect() after a timeout. So
upon calling .disconnect() the interface state may still be
CONNECTING. Clear the CONNECTING bit as well.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In the Makefile for this driver, the wrong Kconfig option is used
to trigger the compilation of the object file. This leads to the
driver only being included into the kernel when both CONFIG_RTL8821AE
and CONFIG_RTL8192AE are set to "y".
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In four of the rtlwifi drivers, the Makefile contains superfluous
statements indicating the compilation of the driver as an LKM
regardless of the corresponding Kconfig option.

If the corresponding option is set to 'y', the build system will then
see the object file in obj-m and obj-y, which leads to a compilation
as a built-in only. Even though this leads to the desired behavior,
the unconditional appearance in obj-m is confusing for someone reading
the Makefile.

This patch removes the superfluous Makefile statements.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For FCC and JP, in one of the radar patterns, PPB and PRF seems to be
interchanged leading to frequent incorrect radar detections.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The usb gadget driver net2280 has exported a header file with the
register definition of the net2280 chip.

Remove the custom/duplicated header file in favor of that header file
in include/linux
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reconfigure RCR register in rtl_op_configure_filter() in order to apply RX
filter configuration
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch fixes a static checker warning:

   drivers/net/wireless/brcm80211/brcmfmac/cfg80211.c:2965
      brcmf_cfg80211_set_pmksa()
	warn: can 'pmkid_len' be negative?

The answer to the question above is likely no so changing its
type to unsigned is sufficient.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Merge tag 'iwlwifi-next-for-john-2014-11-24' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Emmanuel Grumbach <egrumbach@gmail.com> says:

"Major works are CSA and TDLS. On top of that I have a new
firmware API for scan and a few rate control improvements.
Johannes find a few tricks to improve our CPU utilization
and adds support for a new spin of 7265 called 7265D.
Along with this a few random things that don't stand out."
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also update the timeout for the data verification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add a new SDIO card id intended for the new 4165 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In case of channel switch, we need to teardown the TDLS peers.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver knows whether an rx frame was beamformed and marks
it in the radiotap VHT flags. However it should also declare
that it knows to extract this info otherwise this gets discarded
by sniffers like Wireshark.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add support to MFUART loading notification (print notification
data with IWL_DEBUG_INFO)
Signed-off-by: Chaya Rachel Ivgy <chaya.rachel.ivgi@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

call the appropriate iwl_trans_suspend/resume ops
on iwl_mvm_suspend/resume calls.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add suspend/resume trans ops that will be called from
mac80211's suspend/resume ops.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When the device wakes up due to netdetect, we need to query different
things from the firmware than when it wakes up with a normal WoWLAN.
To make this easier, separate the netdetect wake up handling from the
rest.  For now, we don't send netdetect as a wake up reason, treating
it as a non-wireless wake up.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Refactor the iwl_mvm_query_wakeup_reasons() function to split the part
that gets the firmware status from the part that sets up the WoWLAN
status.  This will allow netdetect to reuse the code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We need to send a WOWLAN_CONFIGURATION command also for netdetect and
configure the rfkill release trigger if needed.  To do so, refactor
the code that configures wowlan and netdetect when suspending and send
the WOWLAN_CONFIGURATION command also for net_detect.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>