The generic code is racy when multiple children of a PCI bridge try to
enable it simultaneously.

This leads to drivers trying to access a device through a
not-yet-enabled bridge, and this EEH errors under various
circumstances when using parallel driver probing.

There is work going on to fix that properly in the PCI core but it
will take some time.

x86 gets away with it because (outside of hotplug), the BIOS enables
all the bridges at boot time.

This patch does the same thing on powernv by enabling all bridges that
have child devices at boot time, thus avoiding subsequent races. It's
suitable for backporting to stable and distros, while the proper PCI
fix will probably be significantly more invasive.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Commit 1bd6a1c4 ("powerpc/fadump: handle crash memory ranges array
index overflow") changed crash memory ranges to a dynamic array that
is reallocated on-demand with krealloc(). The relevant header for this
call was not included. The kernel compiles though. But be cautious and
add the header anyway.

Also, memory allocation logic in fadump_add_crash_memory() takes care
of memory allocation for crash memory ranges in all scenarios. Drop
unnecessary memory allocation in fadump_setup_crash_memory_ranges().

Fixes: 1bd6a1c4 ("powerpc/fadump: handle crash memory ranges array index overflow")
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Provide the flush hv_op for the opal hvc driver. This will flush the
firmware console buffers without spinning with interrupts disabled.

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In the recent commit to add an explicit ratelimit state when showing
unhandled signals, commit 35a52a10 ("powerpc/traps: Use an
explicit ratelimit state for show_signal_msg()"), I put the check of
show_unhandled_signals and the ratelimit state before the call to
unhandled_signal() so as to avoid unnecessarily calling the latter
when show_unhandled_signals is false.

However that causes us to check the ratelimit state on every call, so
if we take a lot of *handled* signals that has the effect of making
the ratelimit code print warnings that callbacks have been suppressed
when they haven't.

So rearrange the code so that we check show_unhandled_signals first,
then call unhandled_signal() and finally check the ratelimit state.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>

When idle_power4() hard disables interrupts then finds a soft pending
interrupt, it returns with interrupts hard disabled but without
PACA_IRQ_HARD_DIS set. Commit 9b81c021 ("powerpc/64s: make
PACA_IRQ_HARD_DIS track MSR[EE] closely") added a warning for that
condition (since disabled).

Fix this by adding the PACA_IRQ_HARD_DIS for that case.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add statistics that show how memory is mapped within the kernel linear mapping.
This is similar to commit 37cd944c ("s390/pgtable: add mapping statistics")

We don't do this with Hash translation mode. Hash uses one size (mmu_linear_psize)
to map the kernel linear mapping and we print the linear psize during boot as
below.

"Page orders: linear mapping = 24, virtual = 16, io = 16, vmemmap = 24"

A sample output looks like:

DirectMap4k:           0 kB
DirectMap64k:       18432 kB
DirectMap2M:     1030144 kB
DirectMap1G:    11534336 kB
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Merge some updates from Scott:

"This contains an 8xx compilation fix, and a dpaa device tree fix."

This branch held some hvc related commits (Hypervisor Virtual Console)
so that they could get some wider testing in linux-next before merging.

Merge our fixes branch from the 4.18 cycle to resolve some minor
conflicts.

Currently if you build a 32-bit powerpc kernel and use get_user() to
load a u64 value it will fail to build with eg:

  kernel/rseq.o: In function `rseq_get_rseq_cs':
  kernel/rseq.c:123: undefined reference to `__get_user_bad'

This is hitting the check in __get_user_size() that makes sure the
size we're copying doesn't exceed the size of the destination:

  #define __get_user_size(x, ptr, size, retval)
  do {
  	retval = 0;
  	__chk_user_ptr(ptr);
  	if (size > sizeof(x))
  		(x) = __get_user_bad();

Which doesn't immediately make sense because the size of the
destination is u64, but it's not really, because __get_user_check()
etc. internally create an unsigned long and copy into that:

  #define __get_user_check(x, ptr, size)
  ({
  	long __gu_err = -EFAULT;
  	unsigned long  __gu_val = 0;

The problem being that on 32-bit unsigned long is not big enough to
hold a u64. We can fix this with a trick from hpa in the x86 code, we
statically check the type of x and set the type of __gu_val to either
unsigned long or unsigned long long.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Avoid coverity false warnings like:

  *** CID 187347:  Control flow issues  (UNREACHABLE)
  /arch/powerpc/mm/hash_native_64.c: 819 in native_flush_hash_range()
  813        slot += hidx & _PTEIDX_GROUP_IX;
  814        hptep = htab_address + slot;
  815        want_v = hpte_encode_avpn(vpn, psize, ssize);
  816        hpte_v = hpte_get_old_v(hptep);
  817
  818        if (!HPTE_V_COMPARE(hpte_v, want_v) || !(hpte_v & HPTE_V_VALID))
  >>>     CID 187347:  Control flow issues  (UNREACHABLE)
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The machine check code that flushes and restores bolted segments in
real mode belongs in mm/slb.c. This will also be used by pseries
machine check and idle code in future changes.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Fix the below build error using strlcpy instead of strncpy

In function 'pnv_parse_cpuidle_dt',
    inlined from 'pnv_init_idle_states' at arch/powerpc/platforms/powernv/idle.c:840:7,
    inlined from '__machine_initcall_powernv_pnv_init_idle_states' at arch/powerpc/platforms/powernv/idle.c:870:1:
arch/powerpc/platforms/powernv/idle.c:820:3: error: 'strncpy' specified bound 16 equals destination size [-Werror=stringop-truncation]
   strncpy(pnv_idle_states[i].name, temp_string[i],
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    PNV_IDLE_NAME_LEN);
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch makes sure we update the mmu_gather page size even if we are
requesting for a fullmm flush. This avoids triggering VM_WARN_ON in code
paths like __tlb_remove_page_size that explicitly check for removing range page
size to be same as mmu gather page size.

Fixes: 5a609934 ("powerpc/64s/radix: tlb do not flush on page size when fullmm")
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Acked-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

‘type’ is only used when CONFIG_DEBUG_HIGHMEM is set. So add a possibly
unused tag to variable. Remove warning treated as error with W=1:

  arch/powerpc/mm/highmem.c:59:6: error: variable ‘type’ set but not used [-Werror=unused-but-set-variable]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Make sure to include setup.h to provide the following prototypes:

  - irqstack_early_init
  - setup_power_save
  - initialize_cache_info

Fix the following warnings (treated as error in W=1):

  arch/powerpc/kernel/setup_32.c:198:13: error: no previous prototype for ‘irqstack_early_init’
  arch/powerpc/kernel/setup_32.c:238:13: error: no previous prototype for ‘setup_power_save’
  arch/powerpc/kernel/setup_32.c:253:13: error: no previous prototype for ‘initialize_cache_info’
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add gcc attribute unused for two variables. Fix warnings treated as errors
with W=1:

  arch/powerpc/kernel/prom_init.c:1388:8: error: variable ‘path’ set but not used [-Werror=unused-but-set-variable]
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

These functions can all be static, make it so. Fix warnings treated as
errors with W=1:

  arch/powerpc/platforms/powermac/pci.c:1022:6: error: no previous prototype for ‘pmac_pci_fixup_ohci’
  arch/powerpc/platforms/powermac/pci.c:1057:6: error: no previous prototype for ‘pmac_pci_fixup_cardbus’
  arch/powerpc/platforms/powermac/pci.c:1094:6: error: no previous prototype for ‘pmac_pci_fixup_pciata’

Remove has_address declaration and assignment since it's not used.
Also add gcc attribute unused to fix a warning treated as error with
W=1:

  arch/powerpc/platforms/powermac/pci.c:784:19: error: variable ‘has_address’ set but not used
  arch/powerpc/platforms/powermac/pci.c:907:22: error: variable ‘ht’ set but not used
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Since the value of x is never intended to be read, remove it. Fix
warning treated as error with W=1:

  arch/powerpc/platforms/powermac/udbg_scc.c:76:9: error: variable ‘x’ set but not used
Suggested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

In commit 14baf4d9 ("cxl: Add guest-specific code") the following code
was added:

	if (afu->crs_len < 0) {
		dev_err(&afu->dev, "Unexpected configuration record size value\n");
		return -EINVAL;
	}

However the variable `crs_len` is of type u64 and cannot be compared < 0.
Remove the dead code section. Fix the following warning treated as error
with W=1:

../drivers/misc/cxl/guest.c:919:19: error: comparison of unsigned expression < 0 is always false [-Werror=type-limits]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The header `pmac.h` was not included, leading to the following warnings,
treated as error with W=1:

  arch/powerpc/platforms/powermac/time.c:69:13: error: no previous prototype for ‘pmac_time_init’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/powermac/time.c:207:15: error: no previous prototype for ‘pmac_get_boot_time’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/powermac/time.c:222:6: error: no previous prototype for ‘pmac_get_rtc_time’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/powermac/time.c:240:5: error: no previous prototype for ‘pmac_set_rtc_time’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/powermac/time.c:259:12: error: no previous prototype for ‘via_calibrate_decr’ [-Werror=missing-prototypes]
  arch/powerpc/platforms/powermac/time.c:311:13: error: no previous prototype for ‘pmac_calibrate_decr’ [-Werror=missing-prototypes]

The function `via_calibrate_decr` was made static to silence a warning.
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Add a jump target so that a bit of exception handling can be better
reused at the end of this function.

This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Thiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Currently, in xmon, there is no obvious way to get an address for a
percpu symbol for a particular cpu. Having such an ability would be
good for debugging the system when percpu variables got involved.

Therefore, this patch introduces a new xmon command "lp" to lookup the
address for percpu symbols. Usage of "lp" is similar to "ls", except
that we could add a cpu number to choose the variable of which cpu we
want to lookup. If no cpu number is given, lookup for current cpu.
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

huge_pte_offset_and_shift() has never existed
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The symbol memcpy_nocache_branch defined in order to allow patching
of memset function once cache is enabled leads to confusing reports
by perf tool.

Using the new patch_site functionality solves this issue.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

During Machine Check interrupt on pseries platform, register r3 points
RTAS extended event log passed by hypervisor. Since hypervisor uses r3
to pass pointer to rtas log, it stores the original r3 value at the
start of the memory (first 8 bytes) pointed by r3. Since hypervisor
stores this info and rtas log is in BE format, linux should make
sure to restore r3 value in correct endian format.

Without this patch when MCE handler, after recovery, returns to code that
that caused the MCE may end up with Data SLB access interrupt for invalid
address followed by kernel panic or hang.

  Severe Machine check interrupt [Recovered]
    NIP [d00000000ca301b8]: init_module+0x1b8/0x338 [bork_kernel]
    Initiator: CPU
    Error type: SLB [Multihit]
      Effective address: d00000000ca70000
  cpu 0xa: Vector: 380 (Data SLB Access) at [c0000000fc7775b0]
      pc: c0000000009694c0: vsnprintf+0x80/0x480
      lr: c0000000009698e0: vscnprintf+0x20/0x60
      sp: c0000000fc777830
     msr: 8000000002009033
     dar: a803a30c000000d0
    current = 0xc00000000bc9ef00
    paca    = 0xc00000001eca5c00	 softe: 3	 irq_happened: 0x01
      pid   = 8860, comm = insmod
  vscnprintf+0x20/0x60
  vprintk_emit+0xb4/0x4b0
  vprintk_func+0x5c/0xd0
  printk+0x38/0x4c
  init_module+0x1c0/0x338 [bork_kernel]
  do_one_initcall+0x54/0x230
  do_init_module+0x8c/0x248
  load_module+0x12b8/0x15b0
  sys_finit_module+0xa8/0x110
  system_call+0x58/0x6c
  --- Exception: c00 (System Call) at 00007fff8bda0644
  SP (7fffdfbfe980) is in userspace

This patch fixes this issue.

Fixes: a08a53ea ("powerpc/le: Enable RTAS events support")
Cc: stable@vger.kernel.org # v3.15+
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

With dynamic memory allocation support for crash memory ranges array,
there is no hard limit on the no. of crash memory ranges kernel could
export, but program headers count could overflow in the /proc/vmcore
ELF file while exporting each memory range as PT_LOAD segment. Reduce
the likelihood of a such scenario, by folding adjacent crash memory
ranges which minimizes the total number of PT_LOAD segments.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Crash memory ranges is an array of memory ranges of the crashing kernel
to be exported as a dump via /proc/vmcore file. The size of the array
is set based on INIT_MEMBLOCK_REGIONS, which works alright in most cases
where memblock memory regions count is less than INIT_MEMBLOCK_REGIONS
value. But this count can grow beyond INIT_MEMBLOCK_REGIONS value since
commit 142b45a7 ("memblock: Add array resizing support").

On large memory systems with a few DLPAR operations, the memblock memory
regions count could be larger than INIT_MEMBLOCK_REGIONS value. On such
systems, registering fadump results in crash or other system failures
like below:

  task: c00007f39a290010 ti: c00000000b738000 task.ti: c00000000b738000
  NIP: c000000000047df4 LR: c0000000000f9e58 CTR: c00000000010f180
  REGS: c00000000b73b570 TRAP: 0300   Tainted: G          L   X  (4.4.140+)
  MSR: 8000000000009033 <SF,EE,ME,IR,DR,RI,LE>  CR: 22004484  XER: 20000000
  CFAR: c000000000008500 DAR: 000007a450000000 DSISR: 40000000 SOFTE: 0
  ...
  NIP [c000000000047df4] smp_send_reschedule+0x24/0x80
  LR [c0000000000f9e58] resched_curr+0x138/0x160
  Call Trace:
    resched_curr+0x138/0x160 (unreliable)
    check_preempt_curr+0xc8/0xf0
    ttwu_do_wakeup+0x38/0x150
    try_to_wake_up+0x224/0x4d0
    __wake_up_common+0x94/0x100
    ep_poll_callback+0xac/0x1c0
    __wake_up_common+0x94/0x100
    __wake_up_sync_key+0x70/0xa0
    sock_def_readable+0x58/0xa0
    unix_stream_sendmsg+0x2dc/0x4c0
    sock_sendmsg+0x68/0xa0
    ___sys_sendmsg+0x2cc/0x2e0
    __sys_sendmsg+0x5c/0xc0
    SyS_socketcall+0x36c/0x3f0
    system_call+0x3c/0x100

as array index overflow is not checked for while setting up crash memory
ranges causing memory corruption. To resolve this issue, dynamically
allocate memory for crash memory ranges and resize it incrementally,
in units of pagesize, on hitting array size limit.

Fixes: 2df173d9 ("fadump: Initialize elfcore header and add PT_LOAD program headers.")
Cc: stable@vger.kernel.org # v3.4+
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
[mpe: Just use PAGE_SIZE directly, fixup variable placement]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

commit e8cb7a55 ("powerpc: remove superflous inclusions of
asm/fixmap.h") removed inclusion of asm/fixmap.h from files not
including objects from that file.

However, asm/mmu-8xx.h includes  call to __fix_to_virt(). The proper
way would be to include asm/fixmap.h in asm/mmu-8xx.h but it creates
an inclusion loop.

So we have to leave asm/fixmap.h in sysdep/cpm_common.c for
CONFIG_PPC_EARLY_DEBUG_CPM

  CC      arch/powerpc/sysdev/cpm_common.o
In file included from ./arch/powerpc/include/asm/mmu.h:340:0,
                 from ./arch/powerpc/include/asm/reg_8xx.h:8,
                 from ./arch/powerpc/include/asm/reg.h:29,
                 from ./arch/powerpc/include/asm/processor.h:13,
                 from ./arch/powerpc/include/asm/thread_info.h:28,
                 from ./include/linux/thread_info.h:38,
                 from ./arch/powerpc/include/asm/ptrace.h:159,
                 from ./arch/powerpc/include/asm/hw_irq.h:12,
                 from ./arch/powerpc/include/asm/irqflags.h:12,
                 from ./include/linux/irqflags.h:16,
                 from ./include/asm-generic/cmpxchg-local.h:6,
                 from ./arch/powerpc/include/asm/cmpxchg.h:537,
                 from ./arch/powerpc/include/asm/atomic.h:11,
                 from ./include/linux/atomic.h:5,
                 from ./include/linux/mutex.h:18,
                 from ./include/linux/kernfs.h:13,
                 from ./include/linux/sysfs.h:16,
                 from ./include/linux/kobject.h:20,
                 from ./include/linux/device.h:16,
                 from ./include/linux/node.h:18,
                 from ./include/linux/cpu.h:17,
                 from ./include/linux/of_device.h:5,
                 from arch/powerpc/sysdev/cpm_common.c:21:
arch/powerpc/sysdev/cpm_common.c: In function ‘udbg_init_cpm’:
./arch/powerpc/include/asm/mmu-8xx.h:218:25: error: implicit declaration of function ‘__fix_to_virt’ [-Werror=implicit-function-declaration]
 #define VIRT_IMMR_BASE (__fix_to_virt(FIX_IMMR_BASE))
                         ^
arch/powerpc/sysdev/cpm_common.c:75:7: note: in expansion of macro ‘VIRT_IMMR_BASE’
       VIRT_IMMR_BASE);
       ^
./arch/powerpc/include/asm/mmu-8xx.h:218:39: error: ‘FIX_IMMR_BASE’ undeclared (first use in this function)
 #define VIRT_IMMR_BASE (__fix_to_virt(FIX_IMMR_BASE))
                                       ^
arch/powerpc/sysdev/cpm_common.c:75:7: note: in expansion of macro ‘VIRT_IMMR_BASE’
       VIRT_IMMR_BASE);
       ^
./arch/powerpc/include/asm/mmu-8xx.h:218:39: note: each undeclared identifier is reported only once for each function it appears in
 #define VIRT_IMMR_BASE (__fix_to_virt(FIX_IMMR_BASE))
                                       ^
arch/powerpc/sysdev/cpm_common.c:75:7: note: in expansion of macro ‘VIRT_IMMR_BASE’
       VIRT_IMMR_BASE);
       ^
cc1: all warnings being treated as errors
make[1]: *** [arch/powerpc/sysdev/cpm_common.o] Error 1

Fixes: e8cb7a55 ("powerpc: remove superflous inclusions of asm/fixmap.h")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The problem is the the calculation should be "end - start + 1" but the
plus one is missing in this calculation.

Fixes: 8626816e ("powerpc: add support for MPIC message register API")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch allows the memory removed by memtrace to be readded to the
kernel. So now you don't have to reboot your system to add the memory
back to the kernel or to have a different amount of memory removed.
Signed-off-by: Rashmica Gupta <rashmica.g@gmail.com>
Tested-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

The Cortina PHY is not compatible with IEEE 802.3 clause 45.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[scottwood: made commit message about compatibility, not driver choice]
Signed-off-by: Scott Wood <oss@buserror.net>

The Cortina PHY is not compatible with IEEE 802.3 clause 45.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[scottwood: made commit message about compatibility, not driver choice]
Signed-off-by: Scott Wood <oss@buserror.net>

Cortina PHYs are present on T4240RDB and T2080RDB. Enable the driver
by default.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Scott Wood <oss@buserror.net>

commit e8cb7a55 ("powerpc: remove superflous inclusions of
asm/fixmap.h") removed inclusion of asm/fixmap.h from files not
including objects from that file.

However, asm/mmu-8xx.h includes  call to __fix_to_virt(). The proper
way would be to include asm/fixmap.h in asm/mmu-8xx.h but it creates
an inclusion loop.

So we have to leave asm/fixmap.h in sysdep/cpm_common.c for
CONFIG_PPC_EARLY_DEBUG_CPM

  CC      arch/powerpc/sysdev/cpm_common.o
In file included from ./arch/powerpc/include/asm/mmu.h:340:0,
                 from ./arch/powerpc/include/asm/reg_8xx.h:8,
                 from ./arch/powerpc/include/asm/reg.h:29,
                 from ./arch/powerpc/include/asm/processor.h:13,
                 from ./arch/powerpc/include/asm/thread_info.h:28,
                 from ./include/linux/thread_info.h:38,
                 from ./arch/powerpc/include/asm/ptrace.h:159,
                 from ./arch/powerpc/include/asm/hw_irq.h:12,
                 from ./arch/powerpc/include/asm/irqflags.h:12,
                 from ./include/linux/irqflags.h:16,
                 from ./include/asm-generic/cmpxchg-local.h:6,
                 from ./arch/powerpc/include/asm/cmpxchg.h:537,
                 from ./arch/powerpc/include/asm/atomic.h:11,
                 from ./include/linux/atomic.h:5,
                 from ./include/linux/mutex.h:18,
                 from ./include/linux/kernfs.h:13,
                 from ./include/linux/sysfs.h:16,
                 from ./include/linux/kobject.h:20,
                 from ./include/linux/device.h:16,
                 from ./include/linux/node.h:18,
                 from ./include/linux/cpu.h:17,
                 from ./include/linux/of_device.h:5,
                 from arch/powerpc/sysdev/cpm_common.c:21:
arch/powerpc/sysdev/cpm_common.c: In function ‘udbg_init_cpm’:
./arch/powerpc/include/asm/mmu-8xx.h:218:25: error: implicit declaration of function ‘__fix_to_virt’ [-Werror=implicit-function-declaration]
 #define VIRT_IMMR_BASE (__fix_to_virt(FIX_IMMR_BASE))
                         ^
arch/powerpc/sysdev/cpm_common.c:75:7: note: in expansion of macro ‘VIRT_IMMR_BASE’
       VIRT_IMMR_BASE);
       ^
./arch/powerpc/include/asm/mmu-8xx.h:218:39: error: ‘FIX_IMMR_BASE’ undeclared (first use in this function)
 #define VIRT_IMMR_BASE (__fix_to_virt(FIX_IMMR_BASE))
                                       ^
arch/powerpc/sysdev/cpm_common.c:75:7: note: in expansion of macro ‘VIRT_IMMR_BASE’
       VIRT_IMMR_BASE);
       ^
./arch/powerpc/include/asm/mmu-8xx.h:218:39: note: each undeclared identifier is reported only once for each function it appears in
 #define VIRT_IMMR_BASE (__fix_to_virt(FIX_IMMR_BASE))
                                       ^
arch/powerpc/sysdev/cpm_common.c:75:7: note: in expansion of macro ‘VIRT_IMMR_BASE’
       VIRT_IMMR_BASE);
       ^
cc1: all warnings being treated as errors
make[1]: *** [arch/powerpc/sysdev/cpm_common.o] Error 1

Fixes: e8cb7a55 ("powerpc: remove superflous inclusions of asm/fixmap.h")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Scott Wood <oss@buserror.net>

There are some powerpc selftests, as tm/tm-unavailable, that run for a long
period (>120 seconds), and if it is interrupted, as pressing CRTL-C
(SIGINT), the foreground process (harness) dies but the child process and
threads continue to execute (with PPID = 1 now) in background.

In this case, you'd think the whole test exited, but there are remaining
threads and processes being executed in background. Sometimes these
zombies processes are doing annoying things, as consuming the whole CPU or
dumping things to STDOUT.

This patch fixes this problem by attaching an empty signal handler to
SIGINT in the harness process. This handler will interrupt (EINTR) the
parent process waitpid() call, letting the code to follow through the
normal flow, which will kill all the processes in the child process group.

This patch also fixes a typo.
Signed-off-by: Breno Leitao <leitao@debian.org>
Signed-off-by: Gustavo Romero <gromero@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

For (bad) historical reasons, OPAL used to create a non-standard pair
of properties "opal-interrupts" and "opal-interrupts-names" for
representing the list of interrupts it wants Linux to request on its
behalf.

Among other issues, the opal-interrupts doesn't have a way to carry
the type of interrupts, and they were assumed to be all level
sensitive.

This is wrong on some recent systems where some of them are edge
sensitive causing warnings in the XIVE code and possible misbehaviours
if they need to be retriggered (typically the NPU2 TCE error
interrupts).

This makes Linux switch to using the standard "interrupts" and
"interrupt-names" properties instead when they are available, using
standard of_irq helpers, which can carry all the desired type
information.

Newer versions of OPAL will generate those properties in addition to
the legacy ones.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Fixup prefix logic to check strlen(r->name). Reinstate setting
 of start = 0 in opal_event_shutdown() to avoid double free warnings]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

GCC supports -mcpu=e300c2 and -mcpu=e300c3

This patch gives the opportunity to tune kernel to one of
those two types.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

This patch extends to PPC32 the capability to select the exact
CPU type.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>