cx231xx_devused is racy. Re-implement it in a proper way,
to remove the risk of mangling it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

There are several weirdness at the unregister logic.

First of all, IR has a poll thread. This thread needs to be
removed, as it uses some resources associated to the main driver.
So, the driver needs to explicitly unregister the I2C client for
ir-kbd-i2c.

If, for some reason, the driver needs to wait for a close()
to happen, not all memories will be freed, because the free
logic were in the wrong place.

Also, v4l2_device_unregister() seems to be called too early,
as devices are still using it.

Finally, even with the device disconnected, there is one
USB function call that will still try to talk with it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Reports the auto-detected parameters to userspace.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

If the device got removed, stops polling it. Also, un-registers
it at input/evdev, as it won't work anymore. We can't free the
IR structure yet, as the ir_remove method will be called later.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Now that we set the intfdata on the right interface, the 'lif'
variable is useless.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The following sequence of commands was triggering a kernel crash in
cdev_get():

 modprobe cx231xx
 rmmod cx231xx
 modprobe cx231xx
 v4l2grab -n 1

The problem was that cx231xx_usb_disconnect() was not doing anything
because the test:

	if (!dev->udev)
		return;

was reached (i.e, dev->udev was NULL).

This is due to the fact that the 'dev' pointer placed as intfdata into
the usb_interface structure had the wrong value, because
cx231xx_probe() was doing the usb_set_intfdata() on the wrong
usb_interface structure. For some reason, cx231xx_probe() was doing
the following:

static int cx231xx_usb_probe(struct usb_interface *interface,
			     const struct usb_device_id *id)
{
        struct usb_interface *lif = NULL;
	[...]
        /* store the current interface */
        lif = interface;
	[...]
        /* store the interface 0 back */
        lif = udev->actconfig->interface[0];
	[...]
	usb_set_intfdata(lif, dev);
	[...]
	retval = v4l2_device_register(&interface->dev, &dev->v4l2_dev);
	[...]
}

So, the usb_set_intfdata() was done on udev->actconfig->interface[0]
and not on the 'interface' passed as argument to the ->probe() and
->disconnect() hooks. Later on, v4l2_device_register() was
initializing the intfdata of the correct usb_interface structure as a
pointer to the v4l2_device structure.

Upon unregistration, the ->disconnect() hook was getting the intfdata
of the usb_interface passed as argument... and casted it to a 'struct
cx231xx *' while it was in fact a 'struct v4l2_device *'.

The correct fix seems to just be to set the intfdata on the proper
interface from the beginning. Now, loading/unloading/reloading the
driver allows to use the device properly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

As reported by Toralf:

the build failed with :
  CC [M]  drivers/media/dvb/dvb-core/dvb_ca_en50221.o
In file included from arch/x86/include/asm/uaccess.h:573:0,
                 from include/linux/poll.h:14,
                 from drivers/media/dvb/dvb-core/dvbdev.h:27,
                 from drivers/media/dvb/dvb-core/dvb_ca_en50221.h:27,
                 from drivers/media/dvb/dvb-core/dvb_ca_en50221.c:41:
In function "copy_from_user", inlined from "dvb_ca_en50221_io_write" at drivers/media/dvb/dvb-core/dvb_ca_en50221.c:1314:26: arch/x86/include/asm/uaccess_32.h:211:26: error: call to "copy_from_user_overflow" declared with attribute error: copy_from_user() buffer size is not provably correct
Reported-by: Toralf Foerster <toralf.foerster@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Mario Ceresa <mrceresa@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

These callbacks allow a host video driver
to poll video formats supported by tvp5150.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The patch "dm1105: handle errors from dvb_net_init" moved the
initialization of dvbnet to before frontend attachment but forgot
to adjust the error handling when frontend attachment fails.
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This module does some printks with the loglevel missing.

pr_err() takes care of adding the KERN_ERR tag and the module name.
So we can simplify the code and add the missing printk loglevel by
using it.

Also add a #define pr_fmt() to make this work, and remove a few
unnecessary periods at the end of messages and bump the loglevel of
"Unknown bttv card type" from KERN_WARNING to KERN_ERR while at it.
Inspired-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This way, the messages will be tagged with KERN_DEBUG and not clutter
the log from dmesg unless the "debug" module parameter is set.

[mchehab@redhat.com: whitespace fixes]
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Lift assignments from "if" conditionals for readability.  No change
in functionality intended.
Suggested-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: Stefan Ringel <linuxtv@stefanringel.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This code is wrong as I should have coded it as SYS_DVBC, instead of
SYS_DVBS & friends. Anyway, this check has other problems

1) it does some "magic" by assuming that all QAM modulations are below
  QAM_AUTO;

2) it checks modulation parameters only for one delivery system.
   Or the core should check invalid parameters for all delivery
   systems, or it should let the frontend drivers do it;

3) frontend drivers should already be checking for invalid parameters
   (most of them do it, anyway);

4) not all modulations are mapped at fe->ops.info.caps, so it is not
   even possible to check for the valid modulations inside the core
   for some delivery systems;

5) The core check is incomplete anyway: it only checks for a few
   parameters. If moved into the core other parameters like bandwidth
   and fec should also be checked;

6) 2nd gen DVB-C uses OFDM. So, that test would fail for it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

As reported by Oliver, some old dead code were preserved there.

Thanks-to: Oliver endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Add support for two new types of Leadtek Winfast TV 2000XP tuner

The author of this patch is Istvan Varga.
Only resending current reformated version against current git.
Signed-off-by: Miroslav Slugen <thunder.mmm@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

If ctrls->count is too high the multiplication could overflow and
array_size would be lower than expected.  Mauro and Hans Verkuil
suggested that we cap it at 1024.  That comes from the maximum
number of controls with lots of room for expantion.

$ grep V4L2_CID include/linux/videodev2.h | wc -l
211

Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Smatch complains that i can be one passed the end of the array if we
don't hit the break statement.  We should be using the "audio" here like
we do in the other places.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This is just a cleanup, it doesn't change how the code works.  These
are compound conditions and not bitwise operations so it should be &&
and not &.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Leadtek DTV2000H J has Philips a FMD1216MEX tuner,
and not a FMD1216ME.
Signed-off-by: Miroslav Slugen <thunder.mmm@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This patch replaces the previous one proposed in the thread "xc3028:
force reload of DTV7 firmware in VHF band with Zarlink demodulator",
at the linux-media@vger.kernel.org ML.

The problem is that the firmware DTV78 works fine in UHF band (8 MHz
bandwidth) but is not working at all in VHF band (7 MHz bandwidth).
Reading the comments inside the code, I figured out that the real
problem could be connected to the formula used to calculate the center
frequency offset in VHF band.

In fact, removing this adjustment fixes the problem:

		if ((priv->cur_fw.type & DTV78) && freq < 470000000)
			offset -= 500000;

This is coherent to what was implemented for the DTV7 firmware by an
Australian user:

		if (priv->cur_fw.type & DTV7)
			offset += 500000;

In the end, now the center frequency is the same for all firmwares
(DTV7, DTV8, DTV78) and doesn't depend on channel bandwidth.

The final code looks clean and simple, and there is no need for any
"magic" adjustment:

		if (priv->cur_fw.type & DTV6)
			offset = 1750000;
		else	/* DTV7 or DTV8 or DTV78 */
			offset = 2750000;
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Fix the following build warning:

warning: (RADIO_WL128X) selects TI_ST which has unmet direct dependencies (MISC_DEVICES && NET && GPIOLIB)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Fix the following build warning:

warning: (MEDIA_TUNER) selects MEDIA_TUNER_TEA5761 which has unmet direct
dependencies (MEDIA_SUPPORT && VIDEO_MEDIA && I2C && EXPERIMENTAL)
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

On Thu, 2011-12-15 at 16:42 +0000, Malcolm Priestley wrote:
> > [ 1103.536156] it913x: Chip Version=ec Chip Type=5830
> > [ 1104.336178] it913x: Dual mode=92 Remote=92 Tuner Type=92
> > [ 1106.248116] dvb-usb: found a 'ITE 9135(9006) Generic' in cold state,
> > will try to load a firmware
> > [ 1106.253773] dvb-usb: downloading firmware from file
> > 'dvb-usb-it9135-02.fw'
> > [ 1106.452123] it913x: FRM Starting Firmware Download
> > [ 1130.756039] it913x: FRM Firmware Download Failed (ffffff92)
> > [ 1130.956168] it913x: Chip Version=79 Chip Type=5823
> > [ 1131.592192] it913x: DEV it913x Error
> > [ 1131.592271] usbcore: registered new interface driver it913x
> >
> > No frontend is generated anyway.
>
> Looks like the the firmware is not at all compatible with your device.
>
> Have you applied the patch cleanly to the latest media_build?
>
> These appear to be new version of the 9006. A supplier is sending me one
> of these devices.
>
> As a last resort see if the device works with dvb-usb-it9137-01.fw
>
> You will have force to use this firmware
> dvb-usb-it913x firmware=1

Here is a modified firmware loader for version 2 types.

The firmware must be as in original
./dvb_get_firmware it9135

dd if=dvb-usb-it9135.fw ibs=1 skip=12866 count=5817 of=dvb-usb-it9135-02.fw
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes an obvious typo in the get_frontend() function
of the af9013 driver, recently rewritten by Antti Palosaari.
Signed-off-by: Gianluca Gennari <gennarone@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

By accident, I added an extra comma at the printk format argument.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Add BER monitoring with Pre-Viterbi error rate.

Add UCBLOCKS based on Aborted packets.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Correction to tuner ID 0x51.

Don't force tuner ID 0x60 unless eprom data zero.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Adds support for the Plextor ConvertX PX-AV100U, which uses the
eMPIA EM2820 chip.  The device has a device_id of '0x093b, 0xa003'.  I
am using the existing EM2820_BOARD_PINNACLE_DVC_90 board profile, as
the Pinnacle Dazzle DVC 90/100/101/107, Kaiser Baas Video to DVD
maker, and Kworld DVD Maker 2 were already mapped to it.  Some more
background on the device and my testing can be found at
http://www.donkramer.net/plextor_122710.pdfSigned-off-by: Don Kramer <dgkramer@comcast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Some channels appear weak signal after warm boot.

Because tuner id is not present in eprom 0x38 is
assigned.

9006 devices are now always assigned 0x60.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Fixes issues with PID filter
Stalling of some channels when PID is on.
PID filter not turning off fully.
PID filter can now turn on and off each index.

Removed PID_RST from it913x_pid_filter_ctrl.
Replaced with PID_EN removed from it913x_pid_filter
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The VIDIOC_LOG_STATUS ioctl allows to dump the current status of a driver
to the kernel log. Currently this ioctl is only available at video device
nodes and the subdevs rely on the host driver to expose their core.log_status
operation to user space.

This patch adds VIDIOC_LOG_STATUS support at the sub-device nodes,
for standalone subdevs that expose their own /dev entry.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

The following ioctl sequence causes fimc_dma_run() to start processing without
complete scaler and DMA initialization which causes missing interrupt and
blocking on DQBUF:
S_FMT, STREAMON, QBUF, DQBUF, STREAMOFF, STREAMON, QBUF, DQBUF.

Fix this regression caused by moving pm_runtime* calls to start/stop_streaming
callback by making sure the fimc_m2m_resume() is always invoked when expected.
Reported-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

It is not common for dvb_net_init to fail, but after the patch
"dvb_net_init: return -errno on error" it can fail due to running out
of memory.  Handle this.

From an audit of dvb_net_init callers.
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Reviewed-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

From an audit of dvb_net_init callers, now that that function
returns -errno on error.
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Clean up and error out if dvb_net_init fails (for example due to
ENOMEM).  This involves moving the dvb_net_init call to before
frontend_init to make cleaning up a little easier.

From an audit of dvb_net_init callers, now that dvb_net_init lets
callers know about errors.
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Clean up and error out if dvb_net_init fails (for example when
running out of memory).

From an audit of dvb_net_init callers, now that dvb_net_init
has learned to return a nonzero value from time to time.

[mchehab.redhat.com: codingstyle fix: printk() should include KERN_ facility level]
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Bail out if dvb_net_init encounters an error (for example an
out-of-memory condition), now that it reports them.

[mchehab@redhat.com: CodingStyle fix: don't use  "if ((ret = foo()) < 0)"]
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>

Avoid some repetition by adopting the usual "goto err" idiom for error
handling.
Signed-off-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>