Rewrite the mpc5200 audio DMA code to support both I2S and AC97.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add DAPM switch for HeadsetL/R mute. Since all bits are are needed
for the HFL/R pop removal to work the switch is using the SW_SHADOW
no HW register for the HandsfreeL/R mute.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Shadow, non HW register for dealing with the HandsfreeL/R
muting.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Move the HandsfreeL/R (IHFL/R) pop removal code from the DAPM_MUX_E
to a more appropriate DAPM_PGA_E widget.
Also fix the power-up sequence to match with the TRM.
The power-down sequence is not described in the TRM, so do it
in a way, which seams like the correct sequence.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add a few more mpc5200 PSC defines. More bit fields defines for mpc5200
PSC registers.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Rename the functions in the mpc5200 DMA file from i2s based names to dma
ones to reflect the file they are in.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Basic split of mpc5200 DMA code out from i2s into a standalone file.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fairly minor issues:
 - Don't register the DAIs, it's not required for AC97 devices.
 - Make unexported functions static.
 - Wrap some excessively long lines.
 - Undo tab/space breakage.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Datasheet: http://www.idt.com/products/getDoc.cfm?docID=13134007Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Ensure that we always set a new sysclk when using the FLL in master mode
and pick out the correct value for the sample rate in hw_params().
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The WM9081 is designed to provide high power output at low distortion
levels in space-constrained portable applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Give unique stream names for the two playback streams so
DAPM can figure out which codec_dai is in use.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

With this patch the initial headset pop-removal related values are
configured for the twl4030 codec (ramp delay and sysclk).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

twl4030_setup_data structure can be passed from platform drivers to
the codec via the snd_soc_device->codec_data pointer.

Currently the setup data has support for the Headset pop-removal
related configuration, which differs from board to board.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Should be no impact on the generated code but it helps the compiler
print clearer messages.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds SND_SOC_DAPM_PGA_E to the headset path, which handles
the headset ramp up and down sequences needed for the pop noise
removal.

With this patch the order of the internal components in the twl4030
codec is turned on and off in a correct order.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Misael Lopez Cruz  <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Restructuring the twl4030 codec's DAPM routing to be able to handle the power
sequences correctly.

The twl4030 codec internal implementation have this order:
DAC -> Analog PGA -> Mixer/Mux

While the ASoC framework expects the following order:
DAC -> Mixer -> Analog PGA

This patch moves the Analog PGA handling from SND_SOC_DAPM_PGA to _MIXER and
adds two levels of mixer to handle the digital and analog loopback
functionality.

Now the analog loopback does not powers on any of the DACs.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Tested-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Tested-by: Misael Lopez Cruz  <x0052729@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds support for the integrated ACLC of the TXx9 family.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Connect twl4030 voice DAI to McBSP3 in sdp3430 machine driver.
Voice DAI init function enables corresponding interface by
writting directly to VOICE_IF codec register.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujflausi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add a control for selecting the codec operation mode. TWL4030 codec
has two modes:
- Option 1. Audio only (4 audio DACs)
- Option 2. Voice/Audio (2 audio DACs and voice ADC/DAC)

Control is restricted when a stream is ongoing, since codec's
operation mode cannot be changed on-the-fly.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujflausi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

AUXR is selected by bit 2 and not by bit 1 in the ANAMICR register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

A standard way of making sure we know when the bias level changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Rather than managing the bias level of the system based on if there is
an active audio stream manage it based on there being an active DAPM
widget. This simplifies the code a little, moving the power handling
into one place, and improves audio performance for bypass paths when no
playbacks or captures are active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

sysfs is so standard these days there's no point.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

DAPM has always applied any changes to the power state of widgets as soon
as it has determined that they are required. Instead of doing this store
all the changes that are required on lists of widgets to power up and
down, then iterate over those lists and apply the changes. This changes
the sequence in which changes are implemented, doing all power downs
before power ups and always using the up/down sequences (previously they
were only used when changes were due to DAC/ADC power events). The error
handling is also changed so that we continue attempting to power widgets
if some changes fail.

The main benefit of this is to allow future changes to do optimisations
over the whole power sequence and to reduce the number of walks of the
widget graph required to check the power status of widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Enable TWL4030 VTXL/VTXR and VRX digital filters for uplink
and downlink paths, respectively.

This patch also corrects voice 8/16kHz mode selection bit
(SEL_16K) of CODEC_MODE register.
Signed-off-by: Misael Lopez Cruz <x0052729@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Eliminate direct accesses to the driver_data field.
cf 82ab13b26f15f49be45f15ccc96bfa0b81dfd015

The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@@
struct device *dev;
expression E;
type T;
@@

- dev->driver_data = (T)E
+ dev_set_drvdata(dev, E)

@@
struct device *dev;
type T;
@@

- (T)dev->driver_data
+ dev_get_drvdata(dev)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Use default to optimize the switch/case in magicial_playback_hw_params(),
which also fixes the compile warnings below:
  sound/soc/pxa/magician.c:89: warning: 'acds' may be used uninitialized in this function
  sound/soc/pxa/magician.c:89: warning: 'acps' may be used uninitialized in this function
Signed-off-by: Takashi Iwai <tiwai@suse.de>

Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge branch 'for-2.6.31' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6 into topic/asoc

This is a build fix, resyncing the DaVinci EVM ASoC board code
with the version in the DaVinci tree.  That resync includes
support for the DM355 EVM, although that board isn't yet in
mainline.

(NOTE:  also includes a bugfix to the platform_add_resources
call, recently sent by Chaithrika U S <chaithrika@ti.com> but
not yet merged into the DaVinci tree.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This resyncs the DaVinci I2S code with the version in the DaVinci
tree.  The behavioral change uses updated clock interfaces which
recently merged to mainline.  Two other changes include adding a
comment on the ASP/McBSP/McASP confusion, and dropping pdev->id in
order to support more boards than just the DM644x EVM.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

This is a buildfix for the DaVinci PCM code, resyncing it with
the version in the DaVinci tree.  The notable change is using
current EDMA interfaces, which recently merged to mainline.
(The older interfaces never made it into mainline.)

NOTE:  open issue, the DMA should be to/from SRAM; see chip
errata for more info.  The artifacts are extremely easy to
hear on DM355 hardware (not yet supported in mainline), but
don't seem as audible on DM6446 hardwaare (which does have
mainline support).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The WM9712 can be configured by resistor strapping GPIO4 to behave like
the WM9713 and default to leaving the AC97 link disabled after cold
reset until a warm reset occurs.  In this configuration we need to issue
a warm reset after cold to bring the link up so do so.  The warm reset
will be harmless on systems that don't need it.

[Changelog rewritten to document the reasoning. -- broonie]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

pxa2xx_i2s_resume is :
 - unconditionnaly setting SACR0_ENB
 - unsetting SACR0_ENB in saved SACR0 pxa_i2s.sacr0
fix these.

In pxa2xx_i2s_{resume,suspend}, save/restore registers even
when !dai->active.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

i2s_clk is 'put' for no reason in pxa2xx_i2s_shutdown.
Now we 'get' i2s_clk at probe and 'put' it at driver removal or when
probe fails.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

- hw_params enables both RPL and REC functions each time : Enable the
	appropriate function in pxa2xx_i2s_trigger.
- pxa2xx_i2s_shutdown disables i2s anytime one of RPL or REC function is
	off : Turn it off only when both functions are off.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Make sure we are in a know good state at end of probe :
Reset FIFO logic and registers, and make sure REC and RPL functions
along with FIFO service are disabled (SACR0_RST enables REC and RPL).

Resetting loses current settings so remove reset from stream startup.
Now reset occurs only at probe.
Signed-off-by: Karl Beldan <karl.beldan@mobile-devices.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>