... and adjust the callers
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... and untangle the cleanup on failure to add into pipe.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... doing revert if we end up not using some pages
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Most of the users immediately follow successful iov_iter_get_pages()
with advancing by the amount it had returned.

Provide inline wrappers doing that, convert trivial open-coded
uses of those.

BTW, iov_iter_get_pages() never returns more than it had been asked
to; such checks in cifs ought to be removed someday...
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

All call sites of get_pages_array() are essenitally identical now.
Replace with common helper...

Returns number of slots available in resulting array or 0 on OOM;
it's up to the caller to make sure it doesn't ask to zero-entry
array (i.e. neither maxpages nor size are allowed to be zero).
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

... and don't mangle maxsize there - turn the loop into counting
one instead.  Easier to see that we won't run out of array that
way.  Note that special treatment of the partial buffer in that
thing is an artifact of the non-advancing semantics of
iov_iter_get_pages() - if not for that, it would be append_pipe(),
same as the body of the loop that follows it.  IOW, once we make
iov_iter_get_pages() advancing, the whole thing will turn into
	calculate how many pages do we want
	allocate an array (if needed)
	call append_pipe() that many times.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

same as for pipes and xarrays; after that iov_iter_get_pages() becomes
a wrapper for __iov_iter_get_pages_alloc().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

same as for pipes
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

	The differences between those two are
* pipe_get_pages() gets a non-NULL struct page ** value pointing to
preallocated array + array size.
* pipe_get_pages_alloc() gets an address of struct page ** variable that
contains NULL, allocates the array and (on success) stores its address in
that variable.

	Not hard to combine - always pass struct page ***, have
the previous pipe_get_pages_alloc() caller pass ~0U as cap for
array size.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

zero maxpages is bogus, but best treated as "just return 0";
NULL pages, OTOH, should be treated as a hard bug.

get rid of now completely useless checks in xarray_get_pages{,_alloc}().
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Incidentally, ITER_XARRAY did *not* free the sucker in case when
iter_xarray_populate_pages() returned 0...
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

All their callers are next to each other; all of them
want the total amount of pages and, possibly, the
offset in the partial final buffer.

Combine into a new helper (pipe_npages()), fix the
bogosity in pipe_space_for_user(), while we are at it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

We often need to find whether the last buffer is anon or not, and
currently it's rather clumsy:
	check if ->iov_offset is non-zero (i.e. that pipe is not empty)
	if so, get the corresponding pipe_buffer and check its ->ops
	if it's &default_pipe_buf_ops, we have an anon buffer.

Let's replace the use of ->iov_offset (which is nowhere near similar to
its role for other flavours) with signed field (->last_offset), with
the following rules:
	empty, no buffers occupied:		0
	anon, with bytes up to N-1 filled:	N
	zero-copy, with bytes up to N-1 filled:	-N

That way abs(i->last_offset) is equal to what used to be in i->iov_offset
and empty vs. anon vs. zero-copy can be distinguished by the sign of
i->last_offset.

	Checks for "should we extend the last buffer or should we start
a new one?" become easier to follow that way.

	Note that most of the operations can only be done in a sane
state - i.e. when the pipe has nothing past the current position of
iterator.  About the only thing that could be done outside of that
state is iov_iter_advance(), which transitions to the sane state by
truncating the pipe.  There are only two cases where we leave the
sane state:
	1) iov_iter_get_pages()/iov_iter_get_pages_alloc().  Will be
dealt with later, when we make get_pages advancing - the callers are
actually happier that way.
	2) iov_iter copied, then something is put into the copy.  Since
they share the underlying pipe, the original gets behind.  When we
decide that we are done with the copy (original is not usable until then)
we advance the original.  direct_io used to be done that way; nowadays
it operates on the original and we do iov_iter_revert() to discard
the excessive data.  At the moment there's nothing in the kernel that
could do that to ITER_PIPE iterators, so this reason for insane state
is theoretical right now.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Fold pipe_truncate() into it, clean up.  We can release buffers
in the same loop where we walk backwards to the iterator beginning
looking for the place where the new position will be.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

instead of setting ->iov_offset for new position and calling
pipe_truncate() to adjust ->len of the last buffer and discard
everything after it, adjust ->len at the same time we set ->iov_offset
and use pipe_discard_from() to deal with buffers past that.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

it's only used to get to the partial buffer we can add to,
and that's always the last one, i.e. pipe->head - 1.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

	Expand the only remaining call of push_pipe() (in
__pipe_get_pages()), combine it with the page-collecting loop there.

Note that the only reason it's not a loop doing append_pipe() is
that append_pipe() is advancing, while iov_iter_get_pages() is not.
As soon as it switches to saner semantics, this thing will switch
to using append_pipe().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

New helper: append_pipe().  Extends the last buffer if possible,
allocates a new one otherwise.  Returns page and offset in it
on success, NULL on failure.  iov_iter is advanced past the
data we've got.

Use that instead of push_pipe() in copy-to-pipe primitives;
they get simpler that way.  Handling of short copy (in "mc" one)
is done simply by iov_iter_revert() - iov_iter is in consistent
state after that one, so we can use that.

[Fix for braino caught by Liu Xinpeng <liuxp11@chinatelecom.cn> folded in]
[another braino fix, this time in copy_pipe_to_iter() and pipe_zero();
caught by testcase from Hugh Dickins]
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

There are only two kinds of pipe_buffer in the area used by ITER_PIPE.

1) anonymous - copy_to_iter() et.al. end up creating those and copying
data there.  They have zero ->offset, and their ->ops points to
default_pipe_page_ops.

2) zero-copy ones - those come from copy_page_to_iter(), and page
comes from caller.  ->offset is also caller-supplied - it might be
non-zero.  ->ops points to page_cache_pipe_buf_ops.

Move creation and insertion of those into helpers - push_anon(pipe, size)
and push_page(pipe, page, offset, size) resp., separating them from
the "could we avoid creating a new buffer by merging with the current
head?" logics.
Acked-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

pipe_buffer instances of a pipe are organized as a ring buffer,
with power-of-2 size.  Indices are kept *not* reduced modulo ring
size, so the buffer refered to by index N is
	pipe->bufs[N & (pipe->ring_size - 1)].

Ring size can change over the lifetime of a pipe, but not while
the pipe is locked.  So for any iov_iter primitives it's a constant.
Original conversion of pipes to this layout went overboard trying
to microoptimize that - calculating pipe->ring_size - 1, storing
it in a local variable and using through the function.  In some
cases it might be warranted, but most of the times it only
obfuscates what's going on in there.

Introduce a helper (pipe_buf(pipe, N)) that would encapsulate
that and use it in the obvious cases.  More will follow...
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Use pipe_discard_from() explicitly in generic_file_read_iter(); don't bother
with rather non-obvious use of iov_iter_advance() in there.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Reviewed-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Equivalent of single-segment iovec.  Initialized by iov_iter_ubuf(),
checked for by iter_is_ubuf(), otherwise behaves like ITER_IOVEC
ones.

We are going to expose the things like ->write_iter() et.al. to those
in subsequent commits.

New predicate (user_backed_iter()) that is true for ITER_IOVEC and
ITER_UBUF; places like direct-IO handling should use that for
checking that pages we modify after getting them from iov_iter_get_pages()
would need to be dirtied.

DO NOT assume that replacing iter_is_iovec() with user_backed_iter()
will solve all problems - there's code that uses iter_is_iovec() to
decide how to poke around in iov_iter guts and for that the predicate
replacement obviously won't suffice.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

Pull block driver updates from Jens Axboe:

 - NVMe pull requests via Christoph:
      - add support for In-Band authentication (Hannes Reinecke)
      - handle the persistent internal error AER (Michael Kelley)
      - use in-capsule data for TCP I/O queue connect (Caleb Sander)
      - remove timeout for getting RDMA-CM established event (Israel
        Rukshin)
      - misc cleanups (Joel Granados, Sagi Grimberg, Chaitanya Kulkarni,
        Guixin Liu, Xiang wangx)
      - use command_id instead of req->tag in trace_nvme_complete_rq()
        (Bean Huo)
      - various fixes for the new authentication code (Lukas Bulwahn,
        Dan Carpenter, Colin Ian King, Chaitanya Kulkarni, Hannes
        Reinecke)
      - small cleanups (Liu Song, Christoph Hellwig)
      - restore compat_ioctl support (Nick Bowler)
      - make a nvmet-tcp workqueue lockdep-safe (Sagi Grimberg)
      - enable generic interface (/dev/ngXnY) for unknown command sets
        (Joel Granados, Christoph Hellwig)
      - don't always build constants.o (Christoph Hellwig)
      - print the command name of aborted commands (Christoph Hellwig)

 - MD pull requests via Song:
      - Improve raid5 lock contention, by Logan Gunthorpe.
      - Misc fixes to raid5, by Logan Gunthorpe.
      - Fix race condition with md_reap_sync_thread(), by Guoqing Jiang.
      - Fix potential deadlock with raid5_quiesce and
        raid5_get_active_stripe, by Logan Gunthorpe.
      - Refactoring md_alloc(), by Christoph"
      - Fix md disk_name lifetime problems, by Christoph Hellwig
      - Convert prepare_to_wait() to wait_woken() api, by Logan
        Gunthorpe;
      - Fix sectors_to_do bitmap issue, by Logan Gunthorpe.

 - Work on unifying the null_blk module parameters and configfs API
   (Vincent)

 - drbd bitmap IO error fix (Lars)

 - Set of rnbd fixes (Guoqing, Md Haris)

 - Remove experimental marker on bcache async device registration (Coly)

 - Series from cleaning up the bio splitting (Christoph)

 - Removal of the sx8 block driver. This hardware never really
   widespread, and it didn't receive a lot of attention after the
   initial merge of it back in 2005 (Christoph)

 - A few fixes for s390 dasd (Eric, Jiang)

 - Followup set of fixes for ublk (Ming)

 - Support for UBLK_IO_NEED_GET_DATA for ublk (ZiyangZhang)

 - Fixes for the dio dma alignment (Keith)

 - Misc fixes and cleanups (Ming, Yu, Dan, Christophe

* tag 'for-5.20/block-2022-08-04' of git://git.kernel.dk/linux-block: (136 commits)
  s390/dasd: Establish DMA alignment
  s390/dasd: drop unexpected word 'for' in comments
  ublk_drv: add support for UBLK_IO_NEED_GET_DATA
  ublk_cmd.h: add one new ublk command: UBLK_IO_NEED_GET_DATA
  ublk_drv: cleanup ublksrv_ctrl_dev_info
  ublk_drv: add SET_PARAMS/GET_PARAMS control command
  ublk_drv: fix ublk device leak in case that add_disk fails
  ublk_drv: cancel device even though disk isn't up
  block: fix leaking page ref on truncated direct io
  block: ensure bio_iov_add_page can't fail
  block: ensure iov_iter advances for added pages
  drivers:md:fix a potential use-after-free bug
  md/raid5: Ensure batch_last is released before sleeping for quiesce
  md/raid5: Move stripe_request_ctx up
  md/raid5: Drop unnecessary call to r5c_check_stripe_cache_usage()
  md/raid5: Make is_inactive_blocked() helper
  md/raid5: Refactor raid5_get_active_stripe()
  block: pass struct queue_limits to the bio splitting helpers
  block: move bio_allowed_max_sectors to blk-merge.c
  block: move the call to get_max_io_size out of blk_bio_segment_split
  ...

Pull rdma updates from Jason Gunthorpe:
 "This cycle we got a new RDMA driver "ERDMA" for the Alibaba cloud
  environment. Otherwise the changes are dominated by rxe fixes.

  There is another RDMA driver on the list that might get merged next
  cycle, 'MANA' for the Azure cloud environment.

  Summary:

   - Bug fixes and small features for irdma, hns, siw, qedr, hfi1, mlx5

   - General spelling/grammer fixes

   - rdma cm can follow changes in neighbours for control packets

   - Significant amounts of rxe fixes and spec compliance changes

   - Use the modern NAPI API

   - Use the bitmap API instead of open coding

   - Performance improvements for rtrs

   - Add the ERDMA driver for Alibaba cloud

   - Fix a use after free bug in SRP"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (99 commits)
  RDMA/ib_srpt: Unify checking rdma_cm_id condition in srpt_cm_req_recv()
  RDMA/rxe: Fix error unwind in rxe_create_qp()
  RDMA/mlx5: Add missing check for return value in get namespace flow
  RDMA/rxe: Split qp state for requester and completer
  RDMA/rxe: Generate error completion for error requester QP state
  RDMA/rxe: Update wqe_index for each wqe error completion
  RDMA/srpt: Fix a use-after-free
  RDMA/srpt: Introduce a reference count in struct srpt_device
  RDMA/srpt: Duplicate port name members
  IB/qib: Fix repeated "in" within comments
  RDMA/erdma: Add driver to kernel build environment
  RDMA/erdma: Add the ABI definitions
  RDMA/erdma: Add the erdma module
  RDMA/erdma: Add connection management (CM) support
  RDMA/erdma: Add verbs implementation
  RDMA/erdma: Add verbs header file
  RDMA/erdma: Add event queue implementation
  RDMA/erdma: Add cmdq implementation
  RDMA/erdma: Add main include file
  RDMA/erdma: Add the hardware related definitions
  ...

Pull SCSI updates from James Bottomley:
 "Updates to the usual drivers (ufs, qla2xx, target, lpfc, smartpqi,
  mpi3mr).

  The main driver change that might cause issues on down the road is the
  conversion of some of our oldest surviving drivers to the DMA API
  (should only affect m68k).

  The only major core change is the rework of async resume; the rest are
  either completely trivial or for updating deprecated APIs"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (195 commits)
  scsi: target: Remove XDWRITEREAD emulated support
  scsi: megaraid: Remove the static variable initialisation
  scsi: ch: Do not initialise statics to 0
  scsi: ufs: core: Fix spelling mistake "Cannnot" -> "Cannot"
  scsi: target: iscsi: Do not require target authentication
  scsi: target: iscsi: Allow AuthMethod=None
  scsi: target: iscsi: Support base64 in CHAP
  scsi: target: iscsi: Add support for extended CDB AHS
  scsi: ufs: dt-bindings: Add SC8280XP binding
  scsi: target: iscsi: Fix clang -Wformat warnings
  scsi: ufs: core: Read device property for ref clock
  scsi: libsas: Resume SAS host for phy reset or enable via sysfs
  scsi: hisi_sas: Modify v3 HW SATA completion error processing
  scsi: hisi_sas: Relocate DMA unmap of SMP task
  scsi: hisi_sas: Remove unnecessary variable to hold DMA map elements
  scsi: hisi_sas: Call hisi_sas_slave_configure() from slave_configure_v3_hw()
  scsi: mpi3mr: Delete a stray tab
  scsi: mpi3mr: Unlock on error path
  scsi: mpi3mr: Reduce VD queue depth on detecting throttling
  scsi: mpi3mr: Resource Based Metering
  ...

Pull MMC updates from Ulf Hansson:
 "MMC core:
   - Add support for the asynchronous SDIO wakeup interrupts
   - Skip redundant evaluation of eMMC HS400 caps when no-MMC-cap
   - Add support to store error stats from host drivers
   - Extend debugfs to show error stats from host drivers
   - Add single I/O read support in the recovery path for 4k sector cards

  MMC host:
   - dw_mmc-exynos: Convert corresponding DT bindings to the dtschema
   - dw_mmc-rockchip: Add support for the Rockchip RV1126 variant
   - mmc_spi: Convert corresponding DT bindings to the dtschema
   - mtk-sd: Extend support for interrupts/pinctrls for SDIO low-power mode
   - mtk-sd: Add support for SDIO wake irqs
   - mtk-sd: Add support for the Mediatek MT8188 variant
   - renesas_sdhi: Drop redundant manual tap correction for newer SoCs
   - renesas_sdhi: Add support for the R-Car S4-8 and generic Gen4 variants
   - sdhci/cqhci: Add support to capture stats from host errors
   - sdhci-brcmstb: Add ability to increase max clock rate for SDIO on 72116b0
   - sdhci-msm: Add support for the MSM8998 and SM8450 variant
   - sdhci-of-at91: Fixup UHS-I mode by rewriting of MC1R
   - sdhci-of-dwcmshc: Add support for the Rockchip rk3588 variant
   - sdhci-of-dwcmshc: Enable reset support for the Rockchip variants
   - sdhci-pci-gli: Improve I/O read/write performance for GL9763E
   - sdhci-s3c: Convert corresponding DT bindings to the dtschema
   - tmio: Avoid glitches when resetting

  MEMSTICK core:
   - A couple of minor fixes and cleanups"

* tag 'mmc-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (61 commits)
  mmc: mediatek: add support for SDIO eint wakup IRQ
  mmc: core: Add support for SDIO wakeup interrupt
  dt-bindings: mmc: mtk-sd: extend interrupts and pinctrls properties
  dt-bindings: mmc: rockchip-dw-mshc: Document Rockchip RV1126
  mmc: renesas_sdhi: newer SoCs don't need manual tap correction
  mmc: cavium-thunderx: Add of_node_put() when breaking out of loop
  mmc: cavium-octeon: Add of_node_put() when breaking out of loop
  mmc: core: quirks: Add of_node_put() when breaking out of loop
  mmc: sdhci-brcmstb: use clk_get_rate(base_clk) in PM resume
  dt-bindings: mmc: sdhci-msm: Document the SM8450 compatible
  mmc: sdhci-msm: drop redundant of_device_id entries
  dt-bindings: mmc: sdhci-msm: add MSM8998
  mmc: block: Add single read for 4k sector cards
  mmc: mxcmmc: Use mmc_card_sdio macro
  mmc: core: Use mmc_card_* macro and add a new for the sd_combo type
  dt-bindings: mmc: sdhci-msm: constrain reg-names per variants
  dt-bindings: mmc: sdhci-msm: fix reg-names entries
  dt-bindings: mmc: Add compatible for MediaTek MT8188
  dt-bindings: mmc: sdhci-msm: document resets
  mmc: sdhci-of-at91: fix set_uhs_signaling rewriting of MC1R
  ...

Pull pci updates from Bjorn Helgaas:
 "Enumeration:

   - Consolidate duplicated 'next function' scanning and extend to allow
     'isolated functions' on s390, similar to existing hypervisors
     (Niklas Schnelle)

  Resource management:
   - Implement pci_iobar_pfn() for sparc, which allows us to remove the
     sparc-specific pci_mmap_page_range() and pci_mmap_resource_range().

     This removes the ability to map the entire PCI I/O space using
     /proc/bus/pci, but we believe that's already been broken since
     v2.6.28 (Arnd Bergmann)

   - Move common PCI definitions to asm-generic/pci.h and rework others
     to be be more specific and more encapsulated in arches that need
     them (Stafford Horne)

  Power management:

   - Convert drivers to new *_PM_OPS macros to avoid need for '#ifdef
     CONFIG_PM_SLEEP' or '__maybe_unused' (Bjorn Helgaas)

  Virtualization:

   - Add ACS quirk for Broadcom BCM5750x multifunction NICs that isolate
     the functions but don't advertise an ACS capability (Pavan Chebbi)

  Error handling:

   - Clear PCI Status register during enumeration in case firmware left
     errors logged (Kai-Heng Feng)

   - When we have native control of AER, enable error reporting for all
     devices that support AER. Previously only a few drivers enabled
     this (Stefan Roese)

   - Keep AER error reporting enabled for switches. Previously we
     enabled this during enumeration but immediately disabled it (Stefan
     Roese)

   - Iterate over error counters instead of error strings to avoid
     printing junk in AER sysfs counters (Mohamed Khalfella)

  ASPM:

   - Remove pcie_aspm_pm_state_change() so ASPM config changes, e.g.,
     via sysfs, are not lost across power state changes (Kai-Heng Feng)

  Endpoint framework:

   - Don't stop an EPC when unbinding an EPF from it (Shunsuke Mie)

  Endpoint embedded DMA controller driver:

   - Simplify and clean up support for the DesignWare embedded DMA
     (eDMA) controller (Frank Li, Serge Semin)

  Broadcom STB PCIe controller driver:

   - Avoid config space accesses when link is down because we can't
     recover from the CPU aborts these cause (Jim Quinlan)

   - Look for power regulators described under Root Ports in DT and
     enable them before scanning the secondary bus (Jim Quinlan)

   - Disable/enable regulators in suspend/resume (Jim Quinlan)

  Freescale i.MX6 PCIe controller driver:

   - Simplify and clean up clock and PHY management (Richard Zhu)

   - Disable/enable regulators in suspend/resume (Richard Zhu)

   - Set PCIE_DBI_RO_WR_EN before writing DBI registers (Richard Zhu)

   - Allow speeds faster than Gen2 (Richard Zhu)

   - Make link being down a non-fatal error so controller probe doesn't
     fail if there are no Endpoints connected (Richard Zhu)

  Loongson PCIe controller driver:

   - Add ACPI and MCFG support for Loongson LS7A (Huacai Chen)

   - Avoid config reads to non-existent LS2K/LS7A devices because a
     hardware defect causes machine hangs (Huacai Chen)

   - Work around LS7A integrated devices that report incorrect Interrupt
     Pin values (Jianmin Lv)

  Marvell Aardvark PCIe controller driver:

   - Add support for AER and Slot capability on emulated bridge (Pali
     Rohár)

  MediaTek PCIe controller driver:

   - Add Airoha EN7532 to DT binding (John Crispin)

   - Allow building of driver for ARCH_AIROHA (Felix Fietkau)

  MediaTek PCIe Gen3 controller driver:

   - Print decoded LTSSM state when the link doesn't come up (Jianjun
     Wang)

  NVIDIA Tegra194 PCIe controller driver:

   - Convert DT binding to json-schema (Vidya Sagar)

   - Add DT bindings and driver support for Tegra234 Root Port and
     Endpoint mode (Vidya Sagar)

   - Fix some Root Port interrupt handling issues (Vidya Sagar)

   - Set default Max Payload Size to 256 bytes (Vidya Sagar)

   - Fix Data Link Feature capability programming (Vidya Sagar)

   - Extend Endpoint mode support to devices beyond Controller-5 (Vidya
     Sagar)

  Qualcomm PCIe controller driver:

   - Rework clock, reset, PHY power-on ordering to avoid hangs and
     improve consistency (Robert Marko, Christian Marangi)

   - Move pipe_clk handling to PHY drivers (Dmitry Baryshkov)

   - Add IPQ60xx support (Selvam Sathappan Periakaruppan)

   - Allow ASPM L1 and substates for 2.7.0 (Krishna chaitanya chundru)

   - Add support for more than 32 MSI interrupts (Dmitry Baryshkov)

  Renesas R-Car PCIe controller driver:

   - Convert DT binding to json-schema (Herve Codina)

   - Add Renesas RZ/N1D (R9A06G032) to rcar-gen2 DT binding and driver
     (Herve Codina)

  Samsung Exynos PCIe controller driver:

   - Fix phy-exynos-pcie driver so it follows the 'phy_init() before
     phy_power_on()' PHY programming model (Marek Szyprowski)

  Synopsys DesignWare PCIe controller driver:

   - Simplify and clean up the DWC core extensively (Serge Semin)

   - Fix an issue with programming the ATU for regions that cross a 4GB
     boundary (Serge Semin)

   - Enable the CDM check if 'snps,enable-cdm-check' exists; previously
     we skipped it if 'num-lanes' was absent (Serge Semin)

   - Allocate a 32-bit DMA-able page to be MSI target instead of using a
     driver data structure that may not be addressable with 32-bit
     address (Will McVicker)

   - Add DWC core support for more than 32 MSI interrupts (Dmitry
     Baryshkov)

  Xilinx Versal CPM PCIe controller driver:

   - Add DT binding and driver support for Versal CPM5 Gen5 Root Port
     (Bharat Kumar Gogada)"

* tag 'pci-v5.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (150 commits)
  PCI: imx6: Support more than Gen2 speed link mode
  PCI: imx6: Set PCIE_DBI_RO_WR_EN before writing DBI registers
  PCI: imx6: Reformat suspend callback to keep symmetric with resume
  PCI: imx6: Move the imx6_pcie_ltssm_disable() earlier
  PCI: imx6: Disable clocks in reverse order of enable
  PCI: imx6: Do not hide PHY driver callbacks and refine the error handling
  PCI: imx6: Reduce resume time by only starting link if it was up before suspend
  PCI: imx6: Mark the link down as non-fatal error
  PCI: imx6: Move regulator enable out of imx6_pcie_deassert_core_reset()
  PCI: imx6: Turn off regulator when system is in suspend mode
  PCI: imx6: Call host init function directly in resume
  PCI: imx6: Disable i.MX6QDL clock when disabling ref clocks
  PCI: imx6: Propagate .host_init() errors to caller
  PCI: imx6: Collect clock enables in imx6_pcie_clk_enable()
  PCI: imx6: Factor out ref clock disable to match enable
  PCI: imx6: Move imx6_pcie_clk_disable() earlier
  PCI: imx6: Move imx6_pcie_enable_ref_clk() earlier
  PCI: imx6: Move PHY management functions together
  PCI: imx6: Move imx6_pcie_grp_offset(), imx6_pcie_configure_type() earlier
  PCI: imx6: Convert to NOIRQ_SYSTEM_SLEEP_PM_OPS()
  ...

Pull dmaengine updates from Vinod Koul:
 "New support / Core:

   - Remove DMA_MEMCPY_SG for lack of users

   - Tegra 234 dmaengine support

   - Mediatek MT8365 dma support

   - Apple ADMAC driver

  Updates:

   - Yaml conversion for ST-Ericsson DMA40 binding and Freescale edma

   - rz-dmac updates and device_synchronize support

   - Bunch of typo in comments fixes in drivers

   - multithread support in sf-pdma driver"

* tag 'dmaengine-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (50 commits)
  dmaengine: mediatek: mtk-hsdma: Fix typo 'the the' in comment
  dmaengine: axi-dmac: check cache coherency register
  dmaengine: sh: rz-dmac: Add device_synchronize callback
  dmaengine: sprd: Cleanup in .remove() after pm_runtime_get_sync() failed
  dmaengine: tegra: Add terminate() for Tegra234
  dt-bindings: dmaengine: Add compatible for Tegra234
  dmaengine: xilinx: use strscpy to replace strlcpy
  dmaengine: imx-sdma: Add FIFO stride support for multi FIFO script
  dmaengine: idxd: Correct IAX operation code names
  dmaengine: imx-dma: Cast of_device_get_match_data() with (uintptr_t)
  dmaengine: dw-axi-dmac: ignore interrupt if no descriptor
  dmaengine: dw-axi-dmac: do not print NULL LLI during error
  dmaengine: altera-msgdma: Fixed some inconsistent function name descriptions
  dmaengine: imx-sdma: Add missing struct documentation
  dmaengine: sf-pdma: Add multithread support for a DMA channel
  dt-bindings: dma: dw-axi-dmac: extend the number of interrupts
  dmaengine: dmatest: use strscpy to replace strlcpy
  dmaengine: ste_dma40: fix typo in comment
  dmaengine: jz4780: fix typo in comment
  dmaengine: s3c24xx: fix typo in comment
  ...

Pull clk updates from Stephen Boyd:
 "The clk core gains a new set of APIs that allow drivers to both
  acquire clks and prepare and enable them at the same time. This also
  comes with devm support so that drivers can make a single call to get
  and prepare and enable the clk and have that all undone when their
  driver is removed.

  Many folks have requested this feature over the years, but we've had
  disagreements about how to implement it and if it was worthwhile to
  encourage drivers to use such an API.

  Now it's here, so let's see how it goes.

  I hope that by introducing this API we can identify drivers that would
  benefit from further consolidation of clk API usage, possibly by
  moving such logic to the bus layer and out of drivers altogether.

  Outside of that major API update, we have the usual collection of
  driver updates. A few new SoCs are supported, mostly Qualcomm and
  Renesas this time around. Then we have the long tail of non-critical
  fixes and minor feature additions to various clk drivers.

  And finally more clk provider migration to struct clk_parent_data,
  reducing boot times in the process.

  Summary:

  Core:

   - devm helpers for clk_get() + clk_prepare() and clk_enable()

  New Drivers:

   - Support for the camera clock controller in Qualcomm SM8450 and the
     display and gpu clock controllers in Qualcomm SM8350

   - Add support for the Renesas RZ/Five SoC

  Updates:

   - Various fixes, new clocks and USB GDSCs are introduced for Qualcomm
     IPQ8074

   - Fixes to Qualcomm MSM8939 for issues introduced by inheriting the
     MSM8916 GCC driver

   - Support for a new type of voteable GDSCs used by Qualcomm SC8280XP
     PCIe GDSCs

   - Qualcomm SC8280XP pipe clocks transitioned to the new phy-mux
     implementation

   - Qualcomm MSM8996 GCC, RPM clock driver and some clocks in MSM8994
     GCC are migrated to use clk_parent_data

   - Corrected the topology for Titan (camera) GDSCs on Qualcomm SDM845
     and SM8250

   - Qualcomm MSM8916 gains more possible frequencies for its GP clocks.

   - The GCC and tsens handling on Qualcomm MSM8960 is reworked to mimic
     the design in IPQ8074 to allow the GCC driver to probe earlier.

   - The regulator based mmcx supply for Qualcomm dispcc and videocc is
     dropped, as the only upstream target that adapted this interface
     was transitioned several kernel versions ago

   - Qualcomm GDSCs found to be enabled at boot will now reflect in the
     enable count of the supply, as was done with the regulator supplies
     previously

   - Correct adc1, nic_media and edma1's parents for NXP i.MX93

   - rdiv, mfd values, the return rate in recalc_rate and add more
     frequencies in the table for fracn-gppll on i.MX

   - Remove Allwinner workaround logic/compatible in fixed factor code

   - MediaTek clk driver cleanups

   - Add reset support to more MediaTek clk drivers

   - deduplicate Allwinner ccu_clks arrays

   - Allwinner H6 GPU DFS support

   - Adjust Allwinner Kconfig to limit choice

   - Fix initconst confusion on Renesas R-Car Gen4

   - Add GPT/POEG (PWM) clocks and resets on Renesas RZ/G2L

   - Add PFC and WDT clocks and resets on Renesas RZ/V2M

   - Add thermal, SDHI, Z (CPU core), PCIe, and HSCIF (serial) clocks on
     Renesas R-Car S4-8"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (124 commits)
  clk: fixed-factor: Introduce *clk_hw_register_fixed_factor_parent_hw()
  clk: mux: Introduce devm_clk_hw_register_mux_parent_hws()
  clk: divider: Introduce devm_clk_hw_register_divider_parent_hw()
  clk: qcom: gcc-msm8994: use parent_hws for gpll0/4
  clk: qcom: clk-rpm: convert to parent_data API
  dt-bindings: clock: fix wrong clock documentation for qcom,rpmcc
  clk: qcom: gcc-msm8939: Add missing USB HS system clock frequencies
  clk: qcom: gcc-msm8939: Add missing MDSS MDP clock frequencies
  clk: qcom: gcc-msm8939: Add missing CAMSS CPP clock frequencies
  clk: qcom: gcc-msm8939: Fix venus0_vcodec0_clk frequency definitions
  clk: qcom: gcc-msm8939: Add missing CAMSS CCI bus clock
  clk: qcom: gcc-msm8939: Fix weird field spacing in ftbl_gcc_camss_cci_clk
  clk: qcom: gdsc: Bump parent usage count when GDSC is found enabled
  clk: qcom: Drop mmcx gdsc supply for dispcc and videocc
  clk: qcom: fix build error initializer element is not constant
  clk: sprd: Add dt-bindings include file for UMS512
  dt-bindings: clk: sprd: Add bindings for ums512 clock controller
  clk: sunxi-ng: sun50i: h6: Modify GPU clock configuration to support DFS
  dt-bindings: clock: qcom,gcc-msm8996: add more GCC clock sources
  clk: qcom: add support for SM8350 DISPCC
  ...

Pull gpio updates from Bartosz Golaszewski:
 "Here are the updates for this merge window from the GPIO subsystem.

  We have more lines removed than added thanks to dropping of a driver
  for a platform that's no longer supported. Otherwise the changes are
  pretty straightforward: support for some new models, various
  improvements to existing drivers, some tweaks to the core library code
  and DT bindings updates.

  Summary:

   - remove gpio-vr41xx driver as the only platform using it got dropped
     too

   - add support for suspend/resume to gpio-davinci

   - improvements to the GPIO character device code

   - add support for disabling bias for in-kernel users (up until now
     only user-space could set it)

   - drop unused devm_gpio_free()

   - fix a refcount issue in gpiolib OF

   - use device match helpers where applicable

   - add support for a new model to gpio-rockchip

   - non-functional improvements in gpio-adp5588

   - improve and simplify teardown in gpio-twl4030 and gpio-ucb1400

   - modernize the gpio-74xx-mmio and gpio-adnp drivers

   - coding style improvements in gpio-xilinx, gpio-104-idi-48

   - support new model (pca9571) in gpio-pca9570

   - convert the DT bindings to YAML for gpio-mvebu and update the
     document

   - don't return error codes from remove() in gpio-brcmstb

   - add a library for the intel 8255 PPI interface and use it in
     drivers

   - reduce using magic numbers and improve code readability in several
     drivers

   - convert DT bindings to YAML for gpio-tpic2810

   - add new models to DT bindings for gpio-frl-imx

   - Kconfig improvements

   - other minor tweaks and improvements"

* tag 'gpio-updates-for-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux: (52 commits)
  dt-bindings: gpio: fsl-imx-gpio: Add i.MXRT compatibles
  gpio: 74xx-mmio: Use bits instead of plain numbers for flags
  gpio: xilinx: add missing blank line after declarations
  MAINTAINERS: Update Intel 8255 GPIO driver file list
  gpio: gpio-mm: Implement and utilize register structures
  gpio: 104-idi-48: Implement and utilize register structures
  gpio: 104-dio-48e: Implement and utilize register structures
  gpio: i8255: Introduce the Intel 8255 interface library module
  gpio: 104-idio-16: Implement and utilize register structures
  gpio: ws16c48: Implement and utilize register structures
  gpio: remove VR41XX related gpio driver
  dt-bindings: gpio: add pull-disable flag
  gpiolib: acpi: support bias pull disable
  gpiolib: of: support bias pull disable
  gpiolib: add support for bias pull disable
  gpio: 74xx-mmio: use bits.h macros for all masks
  gpio: 74xx-mmio: Check MMIO_74XX_DIR_IN flag in mmio_74xx_dir_in()
  gpio: 74xx-mmio: Make use of device properties
  gpiolib: cdev: compile out HTE unless CONFIG_HTE selected
  gpiolib: cdev: consolidate edge detector configuration flags
  ...

Merge tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform driver updates from Hans de Goede:

 - Microsoft Surface:
     - SSAM hot unplug support
     - Surface Pro 8 keyboard cover support
     - Tablet mode switch support for Surface Pro 8 and Surface Laptop
       Studio

 - thinkpad_acpi:
     - AMD Automatice Mode Transitions (AMT) support

 - Mellanox:
     - Vulcan chassis COMe NVSwitch management support
     - XH3000 support

 - New generic/shared Intel P2SB (Primary to Sideband) support

 - Lots of small cleanups

 - Various small bugfixes

 - Various new hardware ids / quirks additions

* tag 'platform-drivers-x86-v6.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (105 commits)
  platform/x86/intel/vsec: Fix wrong type for local status variables
  platform/x86: p2sb: Move out of X86_PLATFORM_DEVICES dependency
  platform/x86: pmc_atom: Fix comment typo
  platform/surface: gpe: Add support for 13" Intel version of Surface Laptop 4
  platform/olpc: Fix uninitialized data in debugfs write
  platform/mellanox: mlxreg-lc: Fix error flow and extend verbosity
  platform/x86: pmc_atom: Match all Lex BayTrail boards with critclk_systems DMI table
  platform/x86: sony-laptop: Remove useless comparisons in sony_pic_read_possible_resource()
  tools/power/x86/intel-speed-select: Remove unneeded semicolon
  tools/power/x86/intel-speed-select: Fix off by one check
  platform/surface: tabletsw: Fix __le32 integer access
  Documentation/ABI: Add new attributes for mlxreg-io sysfs interfaces
  Documentation/ABI: mlxreg-io: Fix contact info
  platform/mellanox: mlxreg-io: Add locking for io operations
  platform/x86: mlx-platform: Add COME board revision register
  platform/x86: mlx-platform: Add support for new system XH3000
  platform/x86: mlx-platform: Introduce support for COMe NVSwitch management module for Vulcan chassis
  platform/x86: mlx-platform: Add support for systems equipped with two ASICs
  platform/x86: mlx-platform: Add cosmetic changes for alignment
  platform/x86: mlx-platform: Make activation of some drivers conditional
  ...

Merge tag 'tag-chrome-platform-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux

Pull chrome platform updates from Tzung-Bi Shih:
 "cros_ec_proto:
   - Leverage Kunit and add Kunit test cases
   - Clean-ups
   - Fix typo

  cros_ec_commands:
   - Fix typo
   - Fix compile errors

  cros_kbd_led_backlight:
   - Support OF match
   - Support EC PWM backend

  cros_ec:
   - Always expose the last resume result to fix sleep hang detection on
     ARM-based chromebooks

  wilco_ec:
   - Fix typo

  cros_ec_typec:
   - Clean-ups
   - Use Type-C framework utilities to manage altmode structs"

* tag 'tag-chrome-platform-for-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: (59 commits)
  platform/chrome: cros_kunit_util: add default value for `msg->result`
  platform/chrome: merge Kunit utils and test cases
  platform/chrome: cros_kbd_led_backlight: fix build warning
  platform/chrome: cros_ec_proto: add Kunit test for cros_ec_cmd()
  platform/chrome: cros_ec_proto: add Kunit tests for get_sensor_count
  platform/chrome: cros_ec_proto: add Kunit tests for check_features
  platform/chrome: cros_ec_proto: add Kunit tests for get_host_event
  platform/chrome: cros_ec_proto: add Kunit tests for get_next_event
  platform/chrome: cros_ec_proto: add Kunit test for cros_ec_map_error()
  platform/chrome: cros_ec_proto: add Kunit tests for cmd_xfer_status
  platform/chrome: cros_ec_proto: return -EPROTO if empty payload
  platform/chrome: cros_ec_proto: add Kunit test for empty payload
  platform/chrome: cros_ec_proto: return -EAGAIN when retries timed out
  platform/chrome: cros_ec_proto: change Kunit expectation when timed out
  platform/chrome: cros_ec_proto: separate cros_ec_wait_until_complete()
  platform/chrome: cros_ec_proto: separate cros_ec_xfer_command()
  platform/chrome: cros_ec_proto: add Kunit tests for cros_ec_send_command()
  platform/chrome: cros_ec_proto: add Kunit tests for cros_ec_cmd_xfer()
  platform/chrome: cros_ec_proto: add "cros_ec_" prefix to send_command()
  platform/chrome: cros_ec_typec: Register port altmodes
  ...

Pull devicetree updates from Rob Herring:
 "Bindings:

   - Add spi-peripheral-props.yaml references to various SPI device
     bindings

   - Convert qcom,pm8916-wdt, ds1307, Qualcomm BAM DMA, is31fl319x,
     skyworks,aat1290, Rockchip EMAC, gpio-ir-receiver, ahci-ceva, Arm
     CCN PMU, rda,8810pl-intc, sil,sii9022, ps2-gpio, and
     arm-firmware-suite bindings to DT schema format

   - New bindings for Arm virtual platforms display, Qualcomm IMEM
     memory region, Samsung S5PV210 ChipID, EM Microelectronic EM3027
     RTC, and arm,cortex-a78ae

   - Add vendor prefixes for asrock, bytedance, hxt, ingrasys, inventec,
     quanta, and densitron

   - Add missing MSI and IOMMU properties to host-generic-pci

   - Remove bindings for removed EFM32 platform

   - Remove old chosen.txt binding (replaced by schema)

   - Treewide add missing type information for properties

   - Treewide fixing of typos and its vs. it's in bindings. Its all good
     now.

   - Drop unnecessary quoting in power related schemas

   - Several LED binding updates which didn't get picked up

   - Move various bindings to proper directories

  DT core code:

   - Convert unittest GPIO related tests to use fwnode

   - Check ima-kexec-buffer against memory bounds

   - Print reserved-memory allocation/reservation failures as errors

   - Cleanup early_init_dt_reserve_memory_arch()

   - Simplify of_overlay_fdt_apply() tail"

* tag 'devicetree-for-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (65 commits)
  dt-bindings: mtd: microchip,mchp48l640: use spi-peripheral-props.yaml
  dt-bindings: power: supply: drop quotes when not needed
  dt-bindings: power: reset: drop quotes when not needed
  dt-bindings: power: drop quotes when not needed
  dt-bindings: PCI: host-generic-pci: Allow IOMMU and MSI properties
  of/fdt: declared return type does not match actual return type
  devicetree/bindings: correct possessive "its" typos
  dt-bindings: net: convert emac_rockchip.txt to YAML
  dt-bindings: eeprom: microchip,93lc46b: move to eeprom directory
  dt-bindings: eeprom: at25: use spi-peripheral-props.yaml
  dt-bindings: display: use spi-peripheral-props.yaml
  dt-bindings: watchdog: qcom,pm8916-wdt: convert to dtschema
  dt-bindings: power: reset: qcom,pon: use absolute path to other schema
  dt-bindings: iio/dac: adi,ad5766: Add missing type to 'output-range-microvolts'
  dt-bindings: power: supply: charger-manager: Add missing type for 'cm-battery-stat'
  dt-bindings: panel: raydium,rm67191: Add missing type to 'video-mode'
  of/fdt: Clean up early_init_dt_reserve_memory_arch()
  dt-bindings: PCI: fsl,imx6q-pcie: Add missing type for 'reset-gpio-active-high'
  dt-bindings: rtc: Add EM Microelectronic EM3027 bindings
  dt-bindings: rtc: ds1307: Convert to json-schema
  ...

Pull HID updates from Jiri Kosina:

 - support for AMD SOCs using SFH1.1 memory access (Basavaraj Natikar)

 - XP-PEN Deco L support (José Expósito)

 - support for Elan eKTH6915 touchscreens (Douglas Anderson)

 - other small assorted fixes and device ID additions

* tag 'for-linus-2022080201' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (39 commits)
  HID: amd_sfh: Handle condition of "no sensors"
  HID: amd_sfh: Fix implicit declaration error on i386
  HID: apple: Add "GANSS" to the non-Apple list
  HID: alps: Declare U1_UNICORN_LEGACY support
  HID: wacom: Force pen out of prox if no events have been received in a while
  HID: nintendo: Add missing array termination
  HID: lg-g15: Fix comment typo
  HID: amd_sfh: Implement SFH1.1 functionality
  HID: amd_sfh: Move interrupt handling to common interface
  HID: amd_sfh: Move amd_sfh_work to common interface
  HID: amd_sfh: Move global functions to static
  HID: amd_sfh: Add remove operation in amd_mp2_ops
  HID: amd_sfh: Add PM operations in amd_mp2_ops
  HID: amd_sfh: Add descriptor operations in amd_mp2_ops
  HID: amd_sfh: Move request_list variable to client data
  HID: amd_sfh: Move request_list struct to header file
  HID: amd_sfh: Move common macros and structures
  HID: amd_sfh: Add NULL check for hid device
  HID: core: remove unneeded assignment in hid_process_report()
  ID: intel-ish-hid: hid-client: drop unexpected word "the" in the comments
  ...

Pull xtensa updates from Max Filippov:

 - support KCOV

 - enable ARCH_HAS_GCOV_PROFILE_ALL

 - minor ISS network driver cleanups

* tag 'xtensa-20220804' of https://github.com/jcmvbkbc/linux-xtensa:
  xtensa: enable ARCH_HAS_GCOV_PROFILE_ALL
  xtensa: enable KCOV support
  xtensa: iss: fix handling error cases in iss_net_configure()
  xtensa: iss/network: provide release() callback
  xtensa: iss/network: drop 'devices' list

Pull ARM updates from Russell King:
 "Not much this time around, the 5.20-rc1 development updates for arm
  are:

   - add KASAN support for vmalloc space on arm

   - some sparse fixes from Ben Dooks

   - rework amba device handling (so device addition isn't deferred)"

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
  ARM: 9220/1: amba: Remove deferred device addition
  ARM: 9219/1: fix undeclared soft_restart
  ARM: 9218/1: dma-mapping: fix pointer/integer warning
  ARM: 9217/1: add definition of arch_irq_work_raise()
  ARM: 9203/1: kconfig: fix MODULE_PLTS for KASAN with KASAN_VMALLOC
  ARM: 9202/1: kasan: support CONFIG_KASAN_VMALLOC

Pull csky updates from Guo Ren:

 - Add jump-label implementation

 - Add qspinlock support

 - Enable ARCH_INLINE_READ*/WRITE*/SPIN*

 - Some fixups and a coding convention

* tag 'csky-for-linus-6.0-rc1' of https://github.com/c-sky/csky-linux:
  csky: abiv1: Fixup compile error
  csky: cmpxchg: Coding convention for BUILD_BUG()
  csky: Enable ARCH_INLINE_READ*/WRITE*/SPIN*
  csky: Add qspinlock support
  csky: Add jump-label implementation
  csky: Move HEAD_TEXT_SECTION out of __init_begin-end
  csky: Correct position of _stext
  csky: Use the bitmap API to allocate bitmaps
  csky/kprobe: reclaim insn_slot on kprobe unregistration

Pull AVR32 updates from Hans-Christian Noren Egtvedt:
 "Mostly changes to documentation and comments"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/egtvedt/linux-avr32:
  video:backlight: remove reference to AVR32 architecture in ltv350qv
  video: remove support for non-existing atmel,at32ap-lcdc in atmel_lcdfb
  usb:udc: remove reference to AVR32 architecture in Atmel USBA Kconfig
  sound:spi: remove reference to AVR32 in Atmel AT73C213 DAC driver
  net: remove cdns,at32ap7000-macb device tree entry
  misc: update maintainer email address and description for atmel-ssc
  mfd: remove reference to AVR32 architecture in atmel-smc.c
  dma:dw: remove reference to AVR32 architecture in core.c