commit 5deef555 upstream.

This patch adds support for 0x1045 PID of Telit LE922.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 3c4c615d upstream.

The Parrot NMEA GPS Flight Recorder is a USB composite device
consisting of hub, flash storage, and cp210x usb to serial chip.
It is an accessory to the mass-produced Parrot AR Drone 2.
The device emits standard NMEA messages which make the it compatible
with NMEA compatible software. It was tested using gpsd version 3.11-3
as an NMEA interpreter and using the official Parrot Flight Recorder.
Signed-off-by: Vittorio Alfieri <vittorio88@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 013dd239 upstream.

New revision of Dell Wireless 5809e Gobi 4G HSPA+ Mobile Broadband Card
has new idProduct.

Bus 002 Device 006: ID 413c:81b3 Dell Computer Corp.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x413c Dell Computer Corp.
  idProduct          0x81b3
  bcdDevice            0.06
  iManufacturer           1 Sierra Wireless, Incorporated
  iProduct                2 Dell Wireless 5809e Gobi™ 4G HSPA+ Mobile Broadband Card
  iSerial                 3
  bNumConfigurations      2
Signed-off-by: Patrik Halfar <patrik_halfar@halfarit.cz>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit eab3c4db upstream.

snd-hdsp driver accesses enum item values (int) instead of boolean
values (long) wrongly for some ctl elements.  This patch fixes them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit c1099c32 upstream.

HDSPM driver contains a code issuing zero-division potentially in
system sample rate ctl code.  This patch fixes it by not processing
a zero or invalid rate value as a divisor, as well as excluding the
invalid value to be passed via the given ctl element.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 537e4813 upstream.

snd-hdspm driver accesses enum item values (int) instead of boolean
values (long) wrongly for some ctl elements.  This patch fixes them.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 4cad67fc upstream.

Calling return copy_to_user(...) in an ioctl will not
do the right thing if there's a pagefault:
copy_to_user returns the number of bytes not copied
in this case.

Fix up kvm to do
	return copy_to_user(...)) ?  -EFAULT : 0;

everywhere.
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[ luis: backported to 3.16:
  - dropped changes to arch/arm64/kvm/guest.c ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 1ee9f4bd upstream.

This issue is caused by commit 02323db1 ("cifs: fix
cifs_uniqueid_to_ino_t not to ever return 0"), when BITS_PER_LONG
is 64 on s390x, the corresponding cifs_uniqueid_to_ino_t()
function will cast 64-bit fileid to 32-bit by using (ino_t)fileid,
because ino_t (typdefed __kernel_ino_t) is int type.

It's defined in arch/s390/include/uapi/asm/posix_types.h

    #ifndef __s390x__

    typedef unsigned long   __kernel_ino_t;
    ...
    #else /* __s390x__ */

    typedef unsigned int    __kernel_ino_t;

So the #ifdef condition is wrong for s390x, we can just still use
one cifs_uniqueid_to_ino_t() function with comparing sizeof(ino_t)
and sizeof(u64) to choose the correct execution accordingly.
Signed-off-by: Yadan Fan <ydfan@suse.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 6cc3b242 upstream.

For interim responses we only need to parse a header and update
a number credits. Now it is done for all SMB2+ command except
SMB2_READ which is wrong. Fix this by adding such processing.
Signed-off-by: Pavel Shilovsky <pshilovsky@samba.org>
Tested-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit deb7deff upstream.

When opening a file, SMB2_open() attempts to parse the lease state from the
SMB2 CREATE Response.  However, the parsing code was not careful to ensure
that the create contexts are not empty or invalid, which can lead to out-
of-bounds memory access.  This can be seen easily by trying
to read a file from a OSX 10.11 SMB3 server.  Here is sample crash output:

BUG: unable to handle kernel paging request at ffff8800a1a77cc6
IP: [<ffffffff8828a734>] SMB2_open+0x804/0x960
PGD 8f77067 PUD 0
Oops: 0000 [#1] SMP
Modules linked in:
CPU: 3 PID: 2876 Comm: cp Not tainted 4.5.0-rc3.x86_64.1+ #14
Hardware name: NETGEAR ReadyNAS 314          /ReadyNAS 314          , BIOS 4.6.5 10/11/2012
task: ffff880073cdc080 ti: ffff88005b31c000 task.ti: ffff88005b31c000
RIP: 0010:[<ffffffff8828a734>]  [<ffffffff8828a734>] SMB2_open+0x804/0x960
RSP: 0018:ffff88005b31fa08  EFLAGS: 00010282
RAX: 0000000000000015 RBX: 0000000000000000 RCX: 0000000000000006
RDX: 0000000000000000 RSI: 0000000000000246 RDI: ffff88007eb8c8b0
RBP: ffff88005b31fad8 R08: 666666203d206363 R09: 6131613030383866
R10: 3030383866666666 R11: 00000000000002b0 R12: ffff8800660fd800
R13: ffff8800a1a77cc2 R14: 00000000424d53fe R15: ffff88005f5a28c0
FS:  00007f7c8a2897c0(0000) GS:ffff88007eb80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff8800a1a77cc6 CR3: 000000005b281000 CR4: 00000000000006e0
Stack:
 ffff88005b31fa70 ffffffff88278789 00000000000001d3 ffff88005f5a2a80
 ffffffff00000003 ffff88005d029d00 ffff88006fde05a0 0000000000000000
 ffff88005b31fc78 ffff88006fde0780 ffff88005b31fb2f 0000000100000fe0
Call Trace:
 [<ffffffff88278789>] ? cifsConvertToUTF16+0x159/0x2d0
 [<ffffffff8828cf68>] smb2_open_file+0x98/0x210
 [<ffffffff8811e80c>] ? __kmalloc+0x1c/0xe0
 [<ffffffff882685f4>] cifs_open+0x2a4/0x720
 [<ffffffff88122cef>] do_dentry_open+0x1ff/0x310
 [<ffffffff88268350>] ? cifsFileInfo_get+0x30/0x30
 [<ffffffff88123d92>] vfs_open+0x52/0x60
 [<ffffffff88131dd0>] path_openat+0x170/0xf70
 [<ffffffff88097d48>] ? remove_wait_queue+0x48/0x50
 [<ffffffff88133a29>] do_filp_open+0x79/0xd0
 [<ffffffff8813f2ca>] ? __alloc_fd+0x3a/0x170
 [<ffffffff881240c4>] do_sys_open+0x114/0x1e0
 [<ffffffff881241a9>] SyS_open+0x19/0x20
 [<ffffffff8896e257>] entry_SYSCALL_64_fastpath+0x12/0x6a
Code: 4d 8d 6c 07 04 31 c0 4c 89 ee e8 47 6f e5 ff 31 c9 41 89 ce 44 89 f1 48 c7 c7 28 b1 bd 88 31 c0 49 01 cd 4c 89 ee e8 2b 6f e5 ff <45> 0f b7 75 04 48 c7 c7 31 b1 bd 88 31 c0 4d 01 ee 4c 89 f6 e8
RIP  [<ffffffff8828a734>] SMB2_open+0x804/0x960
 RSP <ffff88005b31fa08>
CR2: ffff8800a1a77cc6
---[ end trace d9f69ba64feee469 ]---
Signed-off-by: Justin Maggard <jmaggard@netgear.com>
Signed-off-by: Steve French <smfrench@gmail.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit b24e7ad1 upstream.

X32 ABI takes the 64bit timespec, thus the timer user status ioctl becomes
incompatible with IA32.  This results in NOTTY error when the ioctl is
issued.

Meanwhile, this struct in X32 is essentially identical with the one in
X86-64, so we can just bypassing to the existing code for this
specific compat ioctl.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 3a72494a upstream.

The timer user status compat ioctl returned the bogus struct used for
64bit architectures instead of the 32bit one.  This patch addresses
it to return the proper struct.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 2251fbbc upstream.

Like the previous fixes for ctl and PCM, we need a fix for
incompatible X32 ABI regarding the rawmidi: namely, struct
snd_rawmidi_status has the timespec, and the size and the alignment on
X32 differ from IA32.

This patch fixes the incompatible ioctl for X32.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 6236d8bb upstream.

The X32 ABI takes the same alignment like x86-64, and this may result
in the incompatible struct size from ia32.  Unfortunately, we hit this
in some control ABI: struct snd_ctl_elem_value differs between them
due to the position of 64bit variable array.  This ends up with the
unknown ioctl (ENOTTY) error.

The fix is to add the compat entries for the new aligned struct.
Reported-and-tested-by: Steven Newbury <steve@snewbury.org.uk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 8160c4e4 upstream.

Calling return copy_to_user(...) in an ioctl will not
do the right thing if there's a pagefault:
copy_to_user returns the number of bytes not copied
in this case.

Fix up vfio to do
	return copy_to_user(...)) ?
		-EFAULT : 0;

everywhere.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
[ luis: backported to 3.16:
  - dropped changes to vfio_platform_common.c ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 4ee34ea3 upstream.

The id buffer in ata_device is a DMA target, but it isn't explicitly
cacheline aligned. Due to this, adjacent fields can be overwritten with
stale data from memory on non coherent architectures. As a result, the
kernel is sometimes unable to communicate with an ATA device.

Fix this by ensuring that the id buffer is cacheline aligned.

This issue is similar to that fixed by Commit 84bda12a
("libata: align ap->sector_buf").
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 38e45d02 upstream.

The setup code for the performance counters in the AMD IOMMU driver
tests whether the counters can be written. It tests to setup a counter
for device 00:00.0, which fails on systems where this particular device
is not covered by the IOMMU.

Fix this by not relying on device 00:00.0 but only on the IOMMU being
present.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit be629c62 upstream.

When a directory is deleted, we don't take too much care about killing off
all the dirents that belong to it — on the basis that on remount, the scan
will conclude that the directory is dead anyway.

This doesn't work though, when the deleted directory contained a child
directory which was moved *out*. In the early stages of the fs build
we can then end up with an apparent hard link, with the child directory
appearing both in its true location, and as a child of the original
directory which are this stage of the mount process we don't *yet* know
is defunct.

To resolve this, take out the early special-casing of the "directories
shall not have hard links" rule in jffs2_build_inode_pass1(), and let the
normal nlink processing happen for directories as well as other inodes.

Then later in the build process we can set ic->pino_nlink to the parent
inode#, as is required for directories during normal operaton, instead
of the nlink. And complain only *then* about hard links which are still
in evidence even after killing off all the unreachable paths.
Reported-by: Liu Song <liu.song11@zte.com.cn>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 49e91e70 upstream.

With this fix, all code paths should now be obtaining the page lock before
f->sem.
Reported-by: Szabó Tamás <sztomi89@gmail.com>
Tested-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 157078f6 upstream.

This reverts commit 5ffd3412
("jffs2: Fix lock acquisition order bug in jffs2_write_begin").

The commit modified jffs2_write_begin() to remove a deadlock with
jffs2_garbage_collect_live(), but this introduced new deadlocks found
by multiple users. page_lock() actually has to be called before
mutex_lock(&c->alloc_sem) or mutex_lock(&f->sem) because
jffs2_write_end() and jffs2_readpage() are called with the page locked,
and they acquire c->alloc_sem and f->sem, resp.

In other words, the lock order in jffs2_write_begin() was correct, and
it is the jffs2_garbage_collect_live() path that has to be changed.

Revert the commit to get rid of the new deadlocks, and to clear the way
for a better fix of the original deadlock.
Reported-by: Deng Chao <deng.chao1@zte.com.cn>
Reported-by: Ming Liu <liu.ming50@gmail.com>
Reported-by: wangzaiwei <wangzaiwei@top-vision.cn>
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit d144dfea upstream.

If we use USB ID pin as wakeup source, and there is a USB block
device on this USB OTG (ID) cable, the system will be deadlock
after system resume.

The root cause for this problem is: the workqueue ci_otg may try
to remove hcd before the driver resume has finished, and hcd will
disconnect the device on it, then, it will call device_release_driver,
and holds the device lock "dev->mutex", but it is never unlocked since
it waits workqueue writeback to run to flush the block information, but
the workqueue writeback is freezable, it is not thawed before driver
resume has finished.

When the driver (device: sd 0:0:0:0:) resume goes to dpm_complete, it
tries to get its device lock "dev->mutex", but it can't get it forever,
then the deadlock occurs. Below call stacks show the situation.

So, in order to fix this problem, we need to change workqueue ci_otg
as freezable, then the work item in this workqueue will be run after
driver's resume, this workqueue will not be blocked forever like above
case since the workqueue writeback has been thawed too.

Tested at: i.mx6qdl-sabresd and i.mx6sx-sdb.

[  555.178869] kworker/u2:13   D c07de74c     0   826      2 0x00000000
[  555.185310] Workqueue: ci_otg ci_otg_work
[  555.189353] Backtrace:
[  555.191849] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0)
[  555.198912]  r10:ee471ba0 r9:00000000 r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4
[  555.206867]  r4:ee470000
[  555.209453] [<c07dec24>] (schedule) from [<c07e2fc4>] (schedule_timeout+0x15c/0x1e0)
[  555.217212]  r4:7fffffff r3:edc2b000
[  555.220862] [<c07e2e68>] (schedule_timeout) from [<c07df6c8>] (wait_for_common+0x94/0x144)
[  555.229140]  r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4 r4:7fffffff
[  555.235980] [<c07df634>] (wait_for_common) from [<c07df790>] (wait_for_completion+0x18/0x1c)
[  555.244430]  r10:00000001 r9:c0b5563c r8:c0042e48 r7:ef086000 r6:eea4372c r5:ef131b00
[  555.252383]  r4:00000000
[  555.254970] [<c07df778>] (wait_for_completion) from [<c0043cb8>] (flush_work+0x19c/0x234)
[  555.263177] [<c0043b1c>] (flush_work) from [<c0043fac>] (flush_delayed_work+0x48/0x4c)
[  555.271106]  r8:ed5b5000 r7:c0b38a3c r6:eea439cc r5:eea4372c r4:eea4372c
[  555.277958] [<c0043f64>] (flush_delayed_work) from [<c00eae18>] (bdi_unregister+0x84/0xec)
[  555.286236]  r4:eea43520 r3:20000153
[  555.289885] [<c00ead94>] (bdi_unregister) from [<c02c2154>] (blk_cleanup_queue+0x180/0x29c)
[  555.298250]  r5:eea43808 r4:eea43400
[  555.301909] [<c02c1fd4>] (blk_cleanup_queue) from [<c0417914>] (__scsi_remove_device+0x48/0xb8)
[  555.310623]  r7:00000000 r6:20000153 r5:ededa950 r4:ededa800
[  555.316403] [<c04178cc>] (__scsi_remove_device) from [<c0415e90>] (scsi_forget_host+0x64/0x68)
[  555.325028]  r5:ededa800 r4:ed5b5000
[  555.328689] [<c0415e2c>] (scsi_forget_host) from [<c0409828>] (scsi_remove_host+0x78/0x104)
[  555.337054]  r5:ed5b5068 r4:ed5b5000
[  555.340709] [<c04097b0>] (scsi_remove_host) from [<c04cdfcc>] (usb_stor_disconnect+0x50/0xb4)
[  555.349247]  r6:ed5b56e4 r5:ed5b5818 r4:ed5b5690 r3:00000008
[  555.355025] [<c04cdf7c>] (usb_stor_disconnect) from [<c04b3bc8>] (usb_unbind_interface+0x78/0x25c)
[  555.363997]  r8:c13919b4 r7:edd3c000 r6:edd3c020 r5:ee551c68 r4:ee551c00 r3:c04cdf7c
[  555.371892] [<c04b3b50>] (usb_unbind_interface) from [<c03dc248>] (__device_release_driver+0x8c/0x118)
[  555.381213]  r10:00000001 r9:edd90c00 r8:c13919b4 r7:ee551c68 r6:c0b546e0 r5:c0b5563c
[  555.389167]  r4:edd3c020
[  555.391752] [<c03dc1bc>] (__device_release_driver) from [<c03dc2fc>] (device_release_driver+0x28/0x34)
[  555.401071]  r5:edd3c020 r4:edd3c054
[  555.404721] [<c03dc2d4>] (device_release_driver) from [<c03db304>] (bus_remove_device+0xe0/0x110)
[  555.413607]  r5:edd3c020 r4:ef17f04c
[  555.417253] [<c03db224>] (bus_remove_device) from [<c03d8128>] (device_del+0x114/0x21c)
[  555.425270]  r6:edd3c028 r5:edd3c020 r4:ee551c00 r3:00000000
[  555.431045] [<c03d8014>] (device_del) from [<c04b1560>] (usb_disable_device+0xa4/0x1e8)
[  555.439061]  r8:edd3c000 r7:eded8000 r6:00000000 r5:00000001 r4:ee551c00
[  555.445906] [<c04b14bc>] (usb_disable_device) from [<c04a8e54>] (usb_disconnect+0x74/0x224)
[  555.454271]  r9:edd90c00 r8:ee551000 r7:ee551c68 r6:ee551c9c r5:ee551c00 r4:00000001
[  555.462156] [<c04a8de0>] (usb_disconnect) from [<c04a8fb8>] (usb_disconnect+0x1d8/0x224)
[  555.470259]  r10:00000001 r9:edd90000 r8:ee471e2c r7:ee551468 r6:ee55149c r5:ee551400
[  555.478213]  r4:00000001
[  555.480797] [<c04a8de0>] (usb_disconnect) from [<c04ae5ec>] (usb_remove_hcd+0xa0/0x1ac)
[  555.488813]  r10:00000001 r9:ee471eb0 r8:00000000 r7:ef3d9500 r6:eded810c r5:eded80b0
[  555.496765]  r4:eded8000
[  555.499351] [<c04ae54c>] (usb_remove_hcd) from [<c04d4158>] (host_stop+0x28/0x64)
[  555.506847]  r6:eeb50010 r5:eded8000 r4:eeb51010
[  555.511563] [<c04d4130>] (host_stop) from [<c04d09b8>] (ci_otg_work+0xc4/0x124)
[  555.518885]  r6:00000001 r5:eeb50010 r4:eeb502a0 r3:c04d4130
[  555.524665] [<c04d08f4>] (ci_otg_work) from [<c00454f0>] (process_one_work+0x194/0x420)
[  555.532682]  r6:ef086000 r5:eeb502a0 r4:edc44480
[  555.537393] [<c004535c>] (process_one_work) from [<c00457b0>] (worker_thread+0x34/0x514)
[  555.545496]  r10:edc44480 r9:ef086000 r8:c0b1a100 r7:ef086034 r6:00000088 r5:edc44498
[  555.553450]  r4:ef086000
[  555.556032] [<c004577c>] (worker_thread) from [<c004bab4>] (kthread+0xdc/0xf8)
[  555.563268]  r10:00000000 r9:00000000 r8:00000000 r7:c004577c r6:edc44480 r5:eddc15c0
[  555.571221]  r4:00000000
[  555.573804] [<c004b9d8>] (kthread) from [<c000fef0>] (ret_from_fork+0x14/0x24)
[  555.581040]  r7:00000000 r6:00000000 r5:c004b9d8 r4:eddc15c0

[  553.429383] sh              D c07de74c     0   694    691 0x00000000
[  553.435801] Backtrace:
[  553.438295] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0)
[  553.445358]  r10:edd3c054 r9:edd3c078 r8:edddbd50 r7:edcbbc00 r6:c1377c34 r5:60000153
[  553.453313]  r4:eddda000
[  553.455896] [<c07dec24>] (schedule) from [<c07deff8>] (schedule_preempt_disabled+0x10/0x14)
[  553.464261]  r4:edd3c058 r3:0000000a
[  553.467910] [<c07defe8>] (schedule_preempt_disabled) from [<c07e0bbc>] (mutex_lock_nested+0x1a0/0x3e8)
[  553.477254] [<c07e0a1c>] (mutex_lock_nested) from [<c03e927c>] (dpm_complete+0xc0/0x1b0)
[  553.485358]  r10:00561408 r9:edd3c054 r8:c0b4863c r7:edddbd90 r6:c0b485d8 r5:edd3c020
[  553.493313]  r4:edd3c0d0
[  553.495896] [<c03e91bc>] (dpm_complete) from [<c03e9388>] (dpm_resume_end+0x1c/0x20)
[  553.503652]  r9:00000000 r8:c0b1a9d0 r7:c1334ec0 r6:c1334edc r5:00000003 r4:00000010
[  553.511544] [<c03e936c>] (dpm_resume_end) from [<c0079894>] (suspend_devices_and_enter+0x158/0x504)
[  553.520604]  r4:00000000 r3:c1334efc
[  553.524250] [<c007973c>] (suspend_devices_and_enter) from [<c0079e74>] (pm_suspend+0x234/0x2cc)
[  553.532961]  r10:00561408 r9:ed6b7300 r8:00000004 r7:c1334eec r6:00000000 r5:c1334ee8
[  553.540914]  r4:00000003
[  553.543493] [<c0079c40>] (pm_suspend) from [<c0078a6c>] (state_store+0x6c/0xc0)

[  555.703684] 7 locks held by kworker/u2:13/826:
[  555.708140]  #0:  ("%s""ci_otg"){++++.+}, at: [<c0045484>] process_one_work+0x128/0x420
[  555.716277]  #1:  ((&ci->work)){+.+.+.}, at: [<c0045484>] process_one_work+0x128/0x420
[  555.724317]  #2:  (usb_bus_list_lock){+.+.+.}, at: [<c04ae5e4>] usb_remove_hcd+0x98/0x1ac
[  555.732626]  #3:  (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224
[  555.740403]  #4:  (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224
[  555.748179]  #5:  (&dev->mutex){......}, at: [<c03dc2f4>] device_release_driver+0x20/0x34
[  555.756487]  #6:  (&shost->scan_mutex){+.+.+.}, at: [<c04097d0>] scsi_remove_host+0x20/0x104

Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 0ba4581c upstream.

The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 287e6611 upstream.

As reported by Soohoon Lee, the HDIO_GET_32BIT ioctl does not
work correctly in compat mode with libata.

I have investigated the issue further and found multiple problems
that all appeared with the same commit that originally introduced
HDIO_GET_32BIT handling in libata back in linux-2.6.8 and presumably
also linux-2.4, as the code uses "copy_to_user(arg, &val, 1)" to copy
a 'long' variable containing either 0 or 1 to user space.

The problems with this are:

* On big-endian machines, this will always write a zero because it
  stores the wrong byte into user space.

* In compat mode, the upper three bytes of the variable are updated
  by the compat_hdio_ioctl() function, but they now contain
  uninitialized stack data.

* The hdparm tool calling this ioctl uses a 'static long' variable
  to store the result. This means at least the upper bytes are
  initialized to zero, but calling another ioctl like HDIO_GET_MULTCOUNT
  would fill them with data that remains stale when the low byte
  is overwritten. Fortunately libata doesn't implement any of the
  affected ioctl commands, so this would only happen when we query
  both an IDE and an ATA device in the same command such as
  "hdparm -N -c /dev/hda /dev/sda"

* The libata code for unknown reasons started using ATA_IOC_GET_IO32
  and ATA_IOC_SET_IO32 as aliases for HDIO_GET_32BIT and HDIO_SET_32BIT,
  while the ioctl commands that were added later use the normal
  HDIO_* names. This is harmless but rather confusing.

This addresses all four issues by changing the code to use put_user()
on an 'unsigned long' variable in HDIO_GET_32BIT, like the IDE subsystem
does, and by clarifying the names of the ioctl commands.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Soohoon Lee <Soohoon.Lee@f5.com>
Tested-by: Soohoon Lee <Soohoon.Lee@f5.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

This reverts commit 73187980, which was
commit f6ff4f67 upstream.

This patch was triggering a Oops in stable kernel 3.10.99.  Christian
agrees that the patch is correct but "assumes that radeon_fence_unref()
can safely take NULL as the fence which is not the case for older
kernels."
Reported-by: Erik Andersen <andersen@codepoet.org>
Acked-by: Christian König <christian.koenig@amd.com>
Cc: Nicolai Hähnle <nicolai.haehnle@amd.com>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 310d3d31 upstream.

This patch fixes a race between setting of SCF_SEND_DELAYED_TAS
in transport_send_task_abort(), and check of the same bit in
transport_check_aborted_status().

It adds a __transport_check_aborted_status() version that is
used by target_execute_cmd() when se_cmd->t_state_lock is
held, and a transport_check_aborted_status() wrapper for
all other existing callers.

Also, it handles the case where the check happens before
transport_send_task_abort() gets called.  For this, go
ahead and set SCF_SEND_DELAYED_TAS early when necessary,
and have transport_send_task_abort() send the abort.

Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ luis: backported to 3.16: based on Nicholas' backport to 3.14 ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 0f4a9431 upstream.

To address the bug where fabric driver level shutdown
of se_cmd occurs at the same time when TMR CMD_T_ABORTED
is happening resulting in a -1 ->cmd_kref, this patch
adds a CMD_T_FABRIC_STOP bit that is used to determine
when TMR + driver I_T nexus shutdown is happening
concurrently.

It changes target_sess_cmd_list_set_waiting() to obtain
se_cmd->cmd_kref + set CMD_T_FABRIC_STOP, and drop local
reference in target_wait_for_sess_cmds() and invoke extra
target_put_sess_cmd() during Task Aborted Status (TAS)
when necessary.

Also, it adds a new target_wait_free_cmd() wrapper around
transport_wait_for_tasks() for the special case within
transport_generic_free_cmd() to set CMD_T_FABRIC_STOP,
and is now aware of CMD_T_ABORTED + CMD_T_TAS status
bits to know when an extra transport_put_cmd() during
TAS is required.

Note transport_generic_free_cmd() is expected to block on
cmd->cmd_wait_comp in order to follow what iscsi-target
expects during iscsi_conn context se_cmd shutdown.

Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
[ luis: backported to 3.16: used Nicholas' backport to 3.14 ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit ebde1ca5 upstream.

This patch fixes a bug in TMR task aborted status (TAS)
handling when multiple sessions are connected to the
same target WWPN endpoint and se_node_acl descriptor,
resulting in TASK_ABORTED status to not be generated
for aborted se_cmds on the remote port.

This is due to core_tmr_handle_tas_abort() incorrectly
comparing se_node_acl instead of se_session, for which
the multi-session case is expected to be sharing the
same se_node_acl.

Instead, go ahead and update core_tmr_handle_tas_abort()
to compare tmr_sess + cmd->se_sess in order to determine
if the LUN_RESET was received on a different I_T nexus,
and TASK_ABORTED status response needs to be generated.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ luis: backported to 3.16: used Nicholas' backport to 3.14 ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit febe562c upstream.

This patch fixes a NULL pointer se_cmd->cmd_kref < 0
refcount bug during TMR LUN_RESET with active se_cmd
I/O, that can be triggered during se_cmd descriptor
shutdown + release via core_tmr_drain_state_list() code.

To address this bug, add common __target_check_io_state()
helper for ABORT_TASK + LUN_RESET w/ CMD_T_COMPLETE
checking, and set CMD_T_ABORTED + obtain ->cmd_kref for
both cases ahead of last target_put_sess_cmd() after
TFO->aborted_task() -> transport_cmd_finish_abort()
callback has completed.

It also introduces SCF_ACK_KREF to determine when
transport_cmd_finish_abort() needs to drop the second
extra reference, ahead of calling target_put_sess_cmd()
for the final kref_put(&se_cmd->cmd_kref).

It also updates transport_cmd_check_stop() to avoid
holding se_cmd->t_state_lock while dropping se_cmd
device state via target_remove_from_state_list(), now
that core_tmr_drain_state_list() is holding the
se_device lock while checking se_cmd state from
within TMR logic.

Finally, move transport_put_cmd() release of SGL +
TMR + extended CDB memory into target_free_cmd_mem()
in order to avoid potential resource leaks in TMR
ABORT_TASK + LUN_RESET code-paths.  Also update
target_release_cmd_kref() accordingly.
Reviewed-by: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ luis: backported to 3.16: used Nicholas' backport to 3.14 ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit a6d9bb1c upstream.

This patch fixes a NULL pointer se_cmd->cmd_kref < 0
refcount bug during TMR LUN_RESET with active TMRs,
triggered during se_cmd + se_tmr_req descriptor
shutdown + release via core_tmr_drain_tmr_list().

To address this bug, go ahead and obtain a local
kref_get_unless_zero(&se_cmd->cmd_kref) for active I/O
to set CMD_T_ABORTED, and transport_wait_for_tasks()
followed by the final target_put_sess_cmd() to drop
the local ->cmd_kref.

Also add two new checks within target_tmr_work() to
avoid CMD_T_ABORTED -> TFO->queue_tm_rsp() callbacks
ahead of invoking the backend -> fabric put in
transport_cmd_check_stop_to_fabric().

For good measure, also change core_tmr_release_req()
to use list_del_init() ahead of se_tmr_req memory
free.
Reviewed-by: Quinn Tran <quinn.tran@qlogic.com>
Cc: Himanshu Madhani <himanshu.madhani@qlogic.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
[ luis: backported to 3.16: used Nicholas' backport to 3.14 ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit d9749fb5 upstream.

Dmitry Vyukov noted recently that the sctp_port_hashtable had an error in
its size computation, observing that the current method never guaranteed
that the hashsize (measured in number of entries) would be a power of two,
which the input hash function for that table requires.  The root cause of
the problem is that two values need to be computed (one, the allocation
order of the storage requries, as passed to __get_free_pages, and two the
number of entries for the hash table).  Both need to be ^2, but for
different reasons, and the existing code is simply computing one order
value, and using it as the basis for both, which is wrong (i.e. it assumes
that ((1<<order)*PAGE_SIZE)/sizeof(bucket) is still ^2 when its not).

To fix this, we change the logic slightly.  We start by computing a goal
allocation order (which is limited by the maximum size hash table we want
to support.  Then we attempt to allocate that size table, decreasing the
order until a successful allocation is made.  Then, with the resultant
successful order we compute the number of buckets that hash table supports,
which we then round down to the nearest power of two, giving us the number
of entries the table actually supports.

I've tested this locally here, using non-debug and spinlock-debug kernels,
and the number of entries in the hashtable consistently work out to be
powers of two in all cases.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: Dmitry Vyukov <dvyukov@google.com>
CC: Vladislav Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit a97eb33f upstream.

An error response from a RTM_GETNETCONF request can return the positive
error value EINVAL in the struct nlmsgerr that can mislead userspace.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit deed49df upstream.

Since the gc of ipv4 route was removed, the route cached would has
no chance to be removed, and even it has been timeout, it still could
be used, cause no code to check it's expires.

Fix this issue by checking  and removing route cache when we get route.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 29e73269 upstream.

Drop reference on the relay_po socket when __pppoe_xmit() succeeds.
This is already handled correctly in the error path.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit aac8d3c2 upstream.

Thomas reports:

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=05c6 ProdID=6001 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Reported-by: Thomas Schäfer <tschaefer@t-online.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 91948309 upstream.

Dmitry reported memory leaks of IP options allocated in
ip_cmsg_send() when/if this function returns an error.

Callers are responsible for the freeing.

Many thanks to Dmitry for the report and diagnostic.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit b7d98729 upstream.

tg3_tso_bug() can hit a condition where the entire tx ring is not big
enough to segment the GSO packet. For example, if MSS is very small,
gso_segs can exceed the tx ring size. When we hit the condition, it
will cause tx timeout.

tg3_tso_bug() is called to handle TSO and DMA hardware bugs.
For TSO bugs, if tg3_tso_bug() cannot succeed, we have to drop the packet.
For DMA bugs, we can still fall back to linearize the SKB and let the
hardware transmit the TSO packet.

This patch adds a function tg3_tso_bug_gso_check() to check if there
are enough tx descriptors for GSO before calling tg3_tso_bug().
The caller will then handle the error appropriately - drop or
lineraize the SKB.

v2: Corrected patch description to avoid confusion.
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 5f74f82e upstream.

Devices may have limits on the number of fragments in an skb they support.
Current codebase uses a constant as maximum for number of fragments one
skb can hold and use.
When enabling scatter/gather and running traffic with many small messages
the codebase uses the maximum number of fragments and may thereby violate
the max for certain devices.
The patch introduces a global variable as max number of fragments.
Signed-off-by: Hans Westgaard Ry <hans.westgaard.ry@oracle.com>
Reviewed-by: Håkon Bugge <haakon.bugge@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 8013d1d7 upstream.

Commit 6fd99094 ("ipv6: Don't reduce hop limit for an interface")
disabled accept hop limit from RA if it is smaller than the current hop
limit for security stuff. But this behavior kind of break the RFC definition.

RFC 4861, 6.3.4.  Processing Received Router Advertisements
   A Router Advertisement field (e.g., Cur Hop Limit, Reachable Time,
   and Retrans Timer) may contain a value denoting that it is
   unspecified.  In such cases, the parameter should be ignored and the
   host should continue using whatever value it is already using.

   If the received Cur Hop Limit value is non-zero, the host SHOULD set
   its CurHopLimit variable to the received value.

So add sysctl option accept_ra_min_hop_limit to let user choose the minimum
hop limit value they can accept from RA. And set default to 1 to meet RFC
standards.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16:
  - added missing DEVCONF_* as suggested by Yoshfuji so that uapi contains
    the same values as mainline
  - adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit 1cdda918 upstream.

Currently, the egress interface index specified via IPV6_PKTINFO
is ignored by __ip6_datagram_connect(), so that RFC 3542 section 6.7
can be subverted when the user space application calls connect()
before sendmsg().
Fix it by initializing properly flowi6_oif in connect() before
performing the route lookup.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>

commit e62a123b upstream.

Neal reported crashes with this stack trace :

 RIP: 0010:[<ffffffff8c57231b>] tcp_v4_send_ack+0x41/0x20f
...
 CR2: 0000000000000018 CR3: 000000044005c000 CR4: 00000000001427e0
...
  [<ffffffff8c57258e>] tcp_v4_reqsk_send_ack+0xa5/0xb4
  [<ffffffff8c1a7caa>] tcp_check_req+0x2ea/0x3e0
  [<ffffffff8c19e420>] tcp_rcv_state_process+0x850/0x2500
  [<ffffffff8c1a6d21>] tcp_v4_do_rcv+0x141/0x330
  [<ffffffff8c56cdb2>] sk_backlog_rcv+0x21/0x30
  [<ffffffff8c098bbd>] tcp_recvmsg+0x75d/0xf90
  [<ffffffff8c0a8700>] inet_recvmsg+0x80/0xa0
  [<ffffffff8c17623e>] sock_aio_read+0xee/0x110
  [<ffffffff8c066fcf>] do_sync_read+0x6f/0xa0
  [<ffffffff8c0673a1>] SyS_read+0x1e1/0x290
  [<ffffffff8c5ca262>] system_call_fastpath+0x16/0x1b

The problem here is the skb we provide to tcp_v4_send_ack() had to
be parked in the backlog of a new TCP fastopen child because this child
was owned by the user at the time an out of window packet arrived.

Before queuing a packet, TCP has to set skb->dev to NULL as the device
could disappear before packet is removed from the queue.

Fix this issue by using the net pointer provided by the socket (being a
timewait or a request socket).

IPv6 is immune to the bug : tcp_v6_send_response() already gets the net
pointer from the socket if provided.

Fixes: 168a8f58 ("tcp: TCP Fast Open Server - main code path")
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jerry Chu <hkchu@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[ luis: backported to 3.16: adjusted context ]
Signed-off-by: Luis Henriques <luis.henriques@canonical.com>