- 27 Oct, 2022 10 commits
-
-
Bean Huo authored
Combine ufshcd_get_lu_power_on_wp_status() and ufshcd_set_queue_depth() into one single ufshcd_lu_init(), so that we only need to read the LUN descriptor once. Signed-off-by:
Bean Huo <beanhuo@micron.com> Link: https://lore.kernel.org/r/20221025222430.277768-3-beanhuo@iokpp.deReviewed-by:
Arthur Simchaev <arthur.simchaev@wdc.com> Reviewed-by:
Bart Van Assche <bvanassche@acm.org> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Bean Huo authored
Ccommit d3d9c457 ("scsi: ufs: Fix memory corruption by ufshcd_read_desc_param()") has properly fixed stack overflow issue. As a result, commit a2fca52e ("scsi: ufs: WB is only available on LUN #0 to #7") is no longer required. Revert it. Cc: Jaegeuk Kim <jaegeuk@kernel.org> Signed-off-by:
-
Colin Ian King authored
Variable i is just being incremented and it's never used anywhere else. The variable and the increment are redundant so remove it. Signed-off-by:
Colin Ian King <colin.i.king@gmail.com> Link: https://lore.kernel.org/r/20221024141101.2161167-1-colin.i.king@gmail.comSigned-off-by:
-
Peter Wang authored
WLUN suspend and resume events are currently not handled by ufshcd_print_evt_hist(). Add the missing events. Signed-off-by:
Peter Wang <peter.wang@mediatek.com> Link: https://lore.kernel.org/r/20221024120602.30019-1-peter.wang@mediatek.comReviewed-by:
Stanley Chu <stanley.chu@mediatek.com> Reviewed-by:
Asutosh Das <quic_asutoshd@quicinc.com> Signed-off-by:
-
Dmitry Bogdanov authored
libiscsi tests check the support of DPO & FUA bits in usage bits of RSOC response. This patch adds support for dynamic usage bits for each opcode. Set support of DPO & FUA bits in usage_bits of RSOC response depending on support DPOFUA in the backstore device. Reviewed-by:
Roman Bolshakov <r.bolshakov@yadro.com> Reviewed-by:
Konstantin Shelekhin <k.shelekhin@yadro.com> Signed-off-by:
Dmitry Bogdanov <d.bogdanov@yadro.com> Link: https://lore.kernel.org/r/20220906103421.22348-7-d.bogdanov@yadro.comReviewed-by:
Mike Christie <michael.christie@oracle.com> Signed-off-by:
-
Dmitry Bogdanov authored
RECEIVE COPY RESULTS is an opcode from 3rd party copy command set and shall be rejected if emulate_3pc attribute is off like EXTENDED COPY. Reviewed-by:
-
Dmitry Bogdanov authored
Allow support for RSOC to be turned off via the emulate_rsoc attibute. This is just for testing purposes. Reviewed-by:
-
Dmitry Bogdanov authored
Report supported opcodes depending on a dynamic device configuration. Reviewed-by:
-
Dmitry Bogdanov authored
Fill the strucures for supported opcodes and usage bits that are reported in REPORT SUPPORTED OPERATION CODES command response. Reviewed-by:
-
Dmitry Bogdanov authored
Add support for REPORT SUPPORTED OPERATION CODES command according to SPC4. Reviewed-by:
-
- 22 Oct, 2022 25 commits
-
-
Bart Van Assche authored
The following deadlock has been observed on multiple test setups: * ufshcd_wl_suspend() is waiting for blk_execute_rq(START STOP UNIT) to complete while ufshcd_wl_suspend() holds host_sem. * The SCSI error handler is activated, changes the host state to SHOST_RECOVERY, ufshcd_eh_host_reset_handler() and ufshcd_err_handler() are called and the latter function tries to obtain host_sem. This is a deadlock because blk_execute_rq() can't execute SCSI commands while the host is in the SHOST_RECOVERY state and because the error handler cannot make progress because host_sem is held by another thread. Fix this deadlock as follows: * Fail attempts to suspend the system while the SCSI error handler is in progress by setting the SCMD_FAIL_IF_RECOVERING flag for START STOP UNIT commands. * If the system is suspending and a START STOP UNIT command times out, handle the SCSI command timeout from inside the context of the SCSI timeout handler instead of activating the SCSI error handler. The runtime power management code is not affected by this deadlock since hba->host_sem is not touched by the runtime power management functions in the UFS driver. Reviewed-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Bart Van Assche authored
Open-code scsi_execute() because a later patch will modify scmd->flags and because scsi_execute() does not support setting scmd->flags. No functionality is changed. Signed-off-by:
-
Bart Van Assche authored
Add a new boolean variable that tracks whether the system is suspending, suspended or resuming. This information will be used in a later commit to fix a deadlock between the SCSI error handler and the suspend code. Reviewed-by:
-
Bart Van Assche authored
Instead of only retrying the START STOP UNIT command if a unit attention is reported, repeat it if any SCSI error is reported by the device or if the command timed out. Signed-off-by:
-
Bart Van Assche authored
Reduce the START STOP UNIT command timeout to one second since on Android devices a kernel panic is triggered if an attempt to suspend the system takes more than 20 seconds. One second should be enough for the START STOP UNIT command since this command completes in less than a millisecond for the UFS devices I have access to. Signed-off-by:
-
Bart Van Assche authored
Convert if (ret) { ... } if (!ret) { ... } into if (ret) { ... } else { ... }. Reviewed-by: -
Bart Van Assche authored
Although the host lock had to be held by ufshcd_clk_scaling_start_busy() callers when that function was introduced, that is no longer the case today. Hence remove the comment that claims that callers of this function must hold the host lock. Reviewed-by:
-
Bart Van Assche authored
The current behavior for SCSI commands submitted while error recovery is ongoing is to retry command submission after error recovery has finished. See also the scsi_host_in_recovery() check in scsi_host_queue_ready(). Add support for failing SCSI commands while host recovery is in progress. This functionality will be used to fix a deadlock in the UFS driver. Cc: Christoph Hellwig <hch@lst.de> Cc: Ming Lei <ming.lei@redhat.com> Cc: John Garry <john.garry@huawei.com> Cc: Mike Christie <michael.christie@oracle.com> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Bart Van Assche authored
Commit 6600593c ("block: rename BLK_EH_NOT_HANDLED to BLK_EH_DONE") made it impossible for .eh_timed_out() implementations to call scsi_done() without causing a crash. Restore support for SCSI timeout handlers to call scsi_done() as follows: * Change all .eh_timed_out() handlers as follows: - Change the return type into enum scsi_timeout_action. - Change BLK_EH_RESET_TIMER into SCSI_EH_RESET_TIMER. - Change BLK_EH_DONE into SCSI_EH_NOT_HANDLED. * In scsi_timeout(), convert the SCSI_EH_* values into BLK_EH_* values. Reviewed-by:
Lee Duncan <lduncan@suse.com> Cc: Christoph Hellwig <hch@lst.de> Cc: Ming Lei <ming.lei@redhat.com> Cc: John Garry <john.garry@huawei.com> Cc: Mike Christie <michael.christie@oracle.com> Cc: Hannes Reinecke <hare@suse.de> Signed-off-by:
-
Bart Van Assche authored
If there is a race between scsi_done() and scsi_timeout() and if scsi_timeout() loses the race, scsi_timeout() should not reset the request timer. Hence change the return value for this case from BLK_EH_RESET_TIMER into BLK_EH_DONE. Although the block layer holds a reference on a request (req->ref) while calling a timeout handler, restarting the timer (blk_add_timer()) while a request is being completed is racy. Reviewed-by:
-
Justin Tee authored
Update lpfc version to 14.2.0.8 Signed-off-by:
Justin Tee <justin.tee@broadcom.com> Link: https://lore.kernel.org/r/20221017164323.14536-5-justintee8345@gmail.comSigned-off-by:
-
Justin Tee authored
The DUMP_MEMORY mailbox command is implemented for page A0 and A2 to retrieve transceiver information from firmware. The mailbox command output is then formatted to print raw data values for userspace to parse via sysfs. Signed-off-by:
-
Justin Tee authored
When bandwidth reduces from or recovers back to 100% due to congestion management, log the event. Signed-off-by:
-
Justin Tee authored
During I/O and simultaneous cat of /sys/kernel/debug/lpfc/fnX/rx_monitor, a hard lockup similar to the call trace below may occur. The spin_lock_bh in lpfc_rx_monitor_report is not protecting from timer interrupts as expected, so change the strength of the spin lock to _irq. Kernel panic - not syncing: Hard LOCKUP CPU: 3 PID: 110402 Comm: cat Kdump: loaded exception RIP: native_queued_spin_lock_slowpath+91 [IRQ stack] native_queued_spin_lock_slowpath at ffffffffb814e30b _raw_spin_lock at ffffffffb89a667a lpfc_rx_monitor_record at ffffffffc0a73a36 [lpfc] lpfc_cmf_timer at ffffffffc0abbc67 [lpfc] __hrtimer_run_queues at ffffffffb8184250 hrtimer_interrupt at ffffffffb8184ab0 smp_apic_timer_interrupt at ffffffffb8a026ba apic_timer_interrupt at ffffffffb8a01c4f [End of IRQ stack] apic_timer_interrupt at ffffffffb8a01c4f lpfc_rx_monitor_report at ffffffffc0a73c80 [lpfc] lpfc_rx_monitor_read at ffffffffc0addde1 [lpfc] full_proxy_read at ffffffffb83e7fc3 vfs_read at ffffffffb833fe71 ksys_read at ffffffffb83402af do_syscall_64 at ffffffffb800430b entry_SYSCALL_64_after_hwframe at ffffffffb8a000ad Signed-off-by:
-
Justin Tee authored
Add missed clearing of phba->sli4_hba.pc_sli4_params.cmf when CMF is turned off. Signed-off-by:
-
Jiapeng Chong authored
The variable page is not used in the function, so delete it. Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2348Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Link: https://lore.kernel.org/r/20221009060249.40178-1-jiapeng.chong@linux.alibaba.comSigned-off-by:
-
Igor Pylypiv authored
The reset_in_progress flag was never set. Signed-off-by:
Igor Pylypiv <ipylypiv@google.com> Link: https://lore.kernel.org/r/20221007230751.309363-1-ipylypiv@google.comReviewed-by:
Andrew Konecki <awkonecki@google.com> Acked-by:
Jack Wang <jinpu.wang@ionos.com> Signed-off-by:
-
John Garry authored
The request associated with a SCSI command coming from the block layer has a unique tag, so use that when possible for getting a slot. Unfortunately we don't support reserved commands in the SCSI midlayer yet. As such, SMP tasks - as an example - will not have a request associated, so in the interim continue to manage those tags for that type of sas_task internally. We reserve an arbitrary 4 tags for these internal tags. Indeed, we already decrement MVS_RSVD_SLOTS by 2 for the shost can_queue when flag MVF_FLAG_SOC is set. This change was made in commit 20b09c29 ("[SCSI] mvsas: add support for 94xx; layout change; bug fixes"), but what those 2 slots are used for is not obvious. Also make the tag management functions static, where possible. Signed-off-by:
John Garry <john.garry@huawei.com> Link: https://lore.kernel.org/r/1666091763-11023-8-git-send-email-john.garry@huawei.comSigned-off-by:
-
John Garry authored
All mvs_tag_init() does is zero the tag bitmap, but this is already done with the kzalloc() call to alloc the tags, so delete this unneeded function. Signed-off-by:
Damien Le Moal <damien.lemoal@opensource.wdc.com> Reviewed-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
-
John Garry authored
The request associated with a SCSI command coming from the block layer has a unique tag, so use that when possible for getting a CCB. Unfortunately we don't support reserved commands in the SCSI midlayer yet, so in the interim continue to manage those tags internally (along with tags for private commands). Signed-off-by:
-
Igor Pylypiv authored
In commit 5a141315 ("scsi: pm80xx: Increase the number of outstanding I/O supported to 1024") the pm8001_ha->tags allocation was moved into pm8001_init_ccb_tag(). This changed the execution order of allocation. pm8001_tag_init() used to be called after the pm8001_ha->tags allocation and now it is called before the allocation. Before: pm8001_pci_probe() `--> pm8001_pci_alloc() `--> pm8001_alloc() `--> pm8001_ha->tags = kzalloc(...) `--> pm8001_tag_init(pm8001_ha); // OK: tags are allocated After: pm8001_pci_probe() `--> pm8001_pci_alloc() | `--> pm8001_alloc() | `--> pm8001_tag_init(pm8001_ha); // NOK: tags are not allocated | `--> pm8001_init_ccb_tag() `--> pm8001_ha->tags = kzalloc(...) // today it is bitmap_zalloc() Since pm8001_ha->tags_num is zero when pm8001_tag_init() is called it does nothing. Tags memory is allocated with bitmap_zalloc() so there is no need to manually clear each bit with pm8001_tag_free(). Reviewed-by:
Changyuan Lyu <changyuanl@google.com> Signed-off-by:
-
John Garry authored
To be consistent with blk-mq, put the reserved tags in the lower region of the tagset. Eventually we hope to get rid of all this reserved tag management. Signed-off-by:
-
John Garry authored
Use sas_task_find_rq() to lookup the request per task for its driver tag. Signed-off-by:
-
John Garry authored
blk-mq already provides a unique tag per request. Some libsas LLDDs - like hisi_sas - already use this tag as the unique per-I/O HW tag. Add a common function to provide the request associated with a sas_task for all libsas LLDDs. Signed-off-by:
Jason Yan <yanaijie@huawei.com> Reviewed-by:
-
Jiapeng Chong authored
The function transport_lba_64_ext() is defined in the target_core_sbc.c file, but not called elsewhere, so remove this unused function. drivers/target/target_core_sbc.c:276:34: warning: unused function 'transport_lba_64_ext'. Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2427Reported-by:
-
- 18 Oct, 2022 5 commits
-
-
Jason Yan authored
The SAS address comparison of asd_sas_port and expander phy is open coded. Replace it with sas_phy_match_port_addr(). Signed-off-by:
Johannes Thumshirn <johannes.thumshirn@wdc.com> Signed-off-by:
-
Jason Yan authored
The SAS address comparison of expander phys is open coded. Replace it with sas_phy_addr_match(). Signed-off-by:
-
Jason Yan authored
The SAS address comparison of domain device and expander phy is open coded. Replace it with sas_phy_match_dev_addr(). Signed-off-by:
-
Jason Yan authored
The attached phy finding is open coded. Replace it with sas_find_attached_phy_id(). To keep things consistent, the return value of hisi_sas_dev_found() is also changed to -ENODEV after calling sas_find_attathed_phy_id() failed. Signed-off-by:
-
Jason Yan authored
The attached phy finding is open coded. Replace it with sas_find_attached_phy_id(). To keep things consistent, the return value of mvs_dev_found_notify() is also changed to -ENODEV after calling sas_find_attathed_phy_id() failed. Signed-off-by:
-
