Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

This is my port of the pc87360 driver. It supports the hardware
monitoring functions of the National Semiconductor PC8736x Super-I/O
family. The PC87360, PC87363 and PC87364 only do fan monitoring and
control. The PC87365 and PC87366 additionally have voltage and
temperature monitoring.

The driver was ported upon request from Wincor-Nixdorf, and tested by
Rolf Müller there. I wish to thank Rolf for his very efficient
cooperation.

Please apply,
thanks.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

The patch below removes an unused function from drivers/i2c/chips/it87.c
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

This is a new I2C chip driver named lm63, which supports National
Semiconductor's LM63 hardware monitoring chip. The LM63 is similar to
the LM86 (which we do support through our lm90 driver) with additional
monitoring and control of a single fan. It is obviously aimed at the CPU
and high-end graphics adapters markets. This new driver is very similar
in nature to the lm83 and lm90 driver so I don't have much to add.

I developed the driver on a request from Hard Data Ltd. which are using
Tyan S4882 boards where four LM63 chips are used (one for each CPU).
Tyan provided remote access to a test system so that I could test my
driver on real LM63 chips.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

i2c-core.c has a few never used functions, patch below removes these dead
functions.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

Signed off by: Justin Thiessen <jthiessen@penguincomputing.com
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

Description: Use msleep_interruptible() instead of schedule_timeout() to
guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

Description: Uses msleep_interruptible() instead of schedule_timeout()
to guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

Description: Use msleep_interruptible() instead of schedule_timeout() to
guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

Description: Use msleep_interruptible() instead of schedule_timeout() to
guarantee the task delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

On Tue, Oct 19, 2004 at 10:21:08PM -0700, Eugene Surovegin wrote:
[snip]
> It looks like this change added race I tried to avoid here.
>
> This code is modeled after __wait_event_interruptible_timeout, where
> "prepare_to_wait" is done _before_ checking completion status. This
> change breaks this, e.g. if IRQ happens right after we check iic->sts,
> but before calling msleep_interruptible(). In this case we'll sleep
> much more than required (seconds instead of microseconds)
>
> Greg, if my analysis is correct, please rollback this change.
>
> Nishanth, I'd be nice if you CC'ed me with this patch, my e-mail is at
> the top of that source file.

Oh, well. I should have used wait_event_interruptible_timeout when I
ported this driver to 2.6.

This patch fixes recently introduced race and also cleans ups some
2.4-ism.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

Signed-off-by: Greg Kroah-Hartman <greg@kroah.com>

.. broken by the rename.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This didn't show up in my "allmodconfig" tests, because the
console requires things to be built-in, not modules.

Posix timers preallocate siqueue structures during timer creation
and keep them for reuse.  This allocation happens in user context
with no locks held, however it's designated as an atomic allocation.
Loosen this restriction, and while we're at it let's do a bit of code
consolidation so signal sending uses same __sigqueue_alloc() helper.
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

missing #include (and placement cleanup)
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Lindent security/security.c.
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Registering a security module can be a noisy operation, esp. when it
retries registration with the primary module.  Eliminate some noise, and
distinguish the return values for register_security so a module can tell
the difference between failure modes.
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Rename security_scaffolding_startup() to security_init().  It always
bothered me.
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

trivial sound/parisc updates:

 - substream->dma_device was removed (Stuart Brady)
 - Fix module unloading (Stuart Brady)
 - Fixed the off-by-one in snd_card_harmony_rate_bits (Stuart Brady)
 - Harmony is a GSC device, not available on pure PCI machines (Matthew Wilcox)
 - Fixed module parameter descriptions for ALSA Harmony (Stuart Brady)

Currently they are in the generic setup, pretty confusing. This patch
moves the io scheduler selection into a seperate menu under block
devices.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

into ppc970.osdl.org:/home/torvalds/v2.6/linux

into ppc970.osdl.org:/home/torvalds/v2.6/linux

Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

annotated, ioremap() use simplified (it can deal with addresses that are
not page-aligned just fine).
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

When the generic IRQ stuff went in, it seems that HARDIRQ_BITS got bumped
from 9 (for ppc64) up to 12.  Consequently, the PREEMPT_ACTIVE bit is now
within HARDIRQ_MASK, and I get in_interrupt() falsely returning true when
PREEMPT_ACTIVE is set, and thus a BUG_ON tripping in arch/ppc64/mm/tlb.c.

The patch below fixes this by changing PREEMPT_ACTIVE to 0x10000000.  I
have changed the PREEMPT_ACTIVE definitions for each of the architectures
that define CONFIG_GENERIC_HARDIRQS (i386, ppc, ppc64, x86_64) and fixed
the comment in include/linux/hardirq.h.  We could perhaps move the
PREEMPT_ACTIVE definition to include/linux/hardirq.h - I don't know why it
is still per-arch.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch fixes build of arch/ppc/kernel/irc.c when CONFIG_TAU_INT
is set.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

The current "generic" implementation of IRQ probing isn't well suited
for ppc in it's current form, and causes issues with yenta_socket
(and possibly others) on pmac laptops. We didn't have a probe implementation
in the past, we probably don't need one anyway, so for now, the fix is to
make this optional and enable it on x86 and x86_64 but not ppc and ppc64
(the 4 archs to use the generic IRQ code).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch updates the G5 thermal control driver, the main change
is support for the new "PowerMac7,3" type desktops including the
dual 2.5Ghz with liquid cooling.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch fixes a typo in the zImage boot wrapper (incorrect printf).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Matthew Dharm <mdharm@momenco.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch fixes a problem when allocating the TCE tables (iommu) during
early boot on some non-LPAR machines with a lot of memory.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

This patch, from John Rose, is the counterpart of one recently
forwarded by Greg KH.  It has the same description, but isn't the same
patch - this is the arch/ppc64 part of the change.

As an unfortunate side effect of runtime addition/removal of PCI Host Bridges,
the RPA DLPAR driver can no longer depend on the success of ioremap_explicit()
(and therefore remap_page_range()) for the case of DLPAR adding an I/O Slot.  

Without addressing this, an attempt to add the first child slot of a newly
added PHB will fail when __ioremap_explicit() determines the mappings for that
range to already exist.

For a little context, __ioremap_explicit() creates mappings for the range of a
newly added slot.  Here's why these calls will be expected to fail in some
cases.  Keep in mind that at boot-time, the PPC64 kernel calls ioremap() for
the entire range spanned by each PHB.  Consider the following scenarios of
DLPAR-adding an I/O slot.

1) Just after boot, one removes an I/O slot.  At this point the range
   associated with the parent PHB is fragmented, and the child range for the
   slot in question is iounmap()'ed.  One then re-adds the slot, at which point
   remap_page_range()/ioremap_explicit() restores the mappings that were
   previously removed.

2) One adds a new PHB, at which point the ppc64-specific addition ioremaps the
   entire PHB range.  One then performs a DLPAR-add of a child slot of that
   PHB.  At this point, mappings already exist for the range of the slot to
   be added.  So remap_page_range()/ioremap_explicit() will fail at this point.

The problem is, there's not a good way to distinguish between cases 1 and 2
from the perspective of the DLPAR driver.  Because of that, I believe the
correct solution to be:

- Removal of relevant error prints from iounmap_explicit(), which is only used
  for DLPAR.
- Removal of error code checks from the RPA driver

Here's the first of these.
Signed-off-by: John Rose <johnrose@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

into pobox.com:/garz/repo/libata-2.6

into pobox.com:/garz/repo/net-drivers-2.6