Bloom filter is updated on transitions from a single rule pattern,
also called master RP, to eRP table and vice versa. Since rules are
being written to or deleted from the Bloom filter on such transitions,
it is not required to keep the same eRP bank ID for the master RP.

Change master RP index assignment so it will be assigned with zero.
This is consistent with the assignment of the first available spot
that is used for allocating eRP's indices.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bloom filter update is required only for rules which reside on an
eRP. When the region has only a single rule pattern then eRP table
is not used, however insertion of another pattern would trigger a
move to an active eRP table so it is imperative to update the Bloom
filter with all previously configured rules.

Add a method that updates Bloom filter entries for all rules
currently configured in the region, on the event of a transition
from master mask to eRP, or vice versa. For that purpose, maintain
a list of all A-TCAM rules within mlxsw_sp_acl_atcam_region.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add calls to eRP module for updating Bloom filter when a rule is
added or removed from the A-TCAM. eRP module will update the Bloom
filter only for cases in which the region has an active eRP table.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add Bloom filter update for rule insertion and rule removal scenarios.
This is done within eRP module in order to assure that Bloom filter
updates are done only for rules which are part of an eRP, as HW does not
consult Bloom filter for entries when there is a single (master) mask in
the region.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spectrum-2 HW uses Bloom filter in order to skip lookups on specific
eRPs. It uses crc-16-Msbit-first calculation over a specific layout
of a rule's key fields combined with eRP ID as well as region ID.
Per potential lookup, iff the Bloom filter entry of the calculated
index is empty, then the lookup can be skipped. Hence, the mlxsw
driver should update the Bloom filter entry per each rule insertion
or deletion when rules are part of an eRP.

Add functions for adding and deleting entries in the Bloom filter.
In order to do so also add crc-16 computation based on the specific
Spectrum-2 polynomial and a function for encoding the crc-16 input
in the manner dictated by HW implementation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lay the foundations for Bloom filter handling. Introduce a new file for
Bloom filter actions.

Add struct mlxsw_sp_acl_bf to struct mlxsw_sp_acl_erp_core and initialize
the Bloom filter data structure. Also take care of proper destruction when
terminating.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the maximum Bloom filter logarithmic size per eRP table bank.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bloom filter is a bit vector which allows the HW a fast lookup on a
small size bit vector, that may reduce the number of lookups on the
A-TCAM memory. PEABFE register allows setting values to the bits of
the bit vector mentioned above.
Add the register to be later used in A-TCAM optimizations.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Roopa Prabhu says:

====================
rtnl fdb get

This series adds support for rtnl fdb get similar to
route get.

v2: add nda_policy, fixes to exact msgs, strict nlmsg parsing

v3: remove unnecessary attribute length checks + simplify code
as pointed out by david
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

tests the below three cases of bridge fdb get:
[bridge, mac, vlan]
[bridge_port, mac, vlan, flags=[NTF_MASTER]]
[vxlandev, mac, flags=NTF_SELF]

depends on iproute2 support for bridge fdb get.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements ndo_fdb_get for a vxlan device.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements ndo_fdb_get for the bridge
fdb.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for fdb get similar to
route get. arguments can be any of the following (similar to fdb add/del/dump):
[bridge, mac, vlan] or
[bridge_port, mac, vlan, flags=[NTF_MASTER]] or
[dev, mac, [vni|vlan], flags=[NTF_SELF]]
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marek Vasut says:

====================
net: dsa: ksz: Clean up the tag code in prep for more switches

Clean up the KSZ DSA tag code in preparation for adding more switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In case the destination address is link local, add override bit into the
switch tag to let such a packet through the switch even if the port is
blocked.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Factor out common code from the tag_ksz , so that the code can be used
with other KSZ family switches which use differenly sized tags.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename the tag Kconfig option and related macros in preparation for
addition of new KSZ family switches with different tag formats.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: David S. Miller <davem@davemloft.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FW team asks to be able to not support RED even if NIC is capable
of buffering for testing and experimentation.  Add an opt-out flag.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit ec49d83f.

Cause build failures when DCCP is modular.

ERROR: "inet_hashinfo2_init" [net/dccp/dccp.ko] undefined!
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to routes and rules, add protocol attribute to neighbor entries
for easier tracking of how each was created.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds coverage of DCCP to reuseport_addr_any selftest.
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit d9fbc7f6 "net: tcp: prefer listeners bound to an address"
removes port-only listener lookups. This caused segfaults in DCCP
lookups because DCCP did not initialize the (addr,port) hashtable.

This patch adds said initialization.

The only non-trivial issue here is the size of the new hashtable.
It seemed reasonable to make it match the size of the port-only
hashtable (= INET_LHTABLE_SIZE) that was used previously. Other
parameters to inet_hashinfo2_init() match those used in TCP.

Tested: syzcaller issues fixed; the second patch in the patchset
        tests that DCCP lookups work correctly.

Fixes: d9fbc7f6 "net: tcp: prefer listeners bound to an address"
Reported-by: syzcaller <syzkaller@googlegroups.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When Protocol Field Compression (PFC) is enabled, the "Protocol" field
in PPP packet will be received without leading 0x00. See section 6.5 in
RFC 1661 for details. So let's decompress protocol field if needed, the
same way it's done in drivers/net/ppp/pptp.c.

In case when "nopcomp" pppd option is not enabled, PFC (pcomp) can be
negotiated during LCP handshake, and L2TP driver in kernel will receive
PPP packets with compressed Protocol field, which in turn leads to next
error:

    Protocol Rejected (unsupported protocol 0x2145)

because instead of Protocol=0x0021 in PPP packet there will be
Protocol=0x21. This patch unwraps it back to 0x0021, which fixes the
issue.

Sending the compressed Protocol field will be implemented in subsequent
patch, this one is self-sufficient.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5e-updates-2018-12-14 (VF Lag)

From Aviv Heller,

Subsequent patches introduce VF LAG, which provdies load-balancing and
high-availability capabilities for VFs associated with different
physical ports of the same Connect-X card.

This series consists of the following:
 - mlx5 devcom, driver infrastructure that facilitates operations that involve
   both core devices (physical functions) of the same card, to synchronize and
   communicate between two driver instances of the same card.
 - Infrastructure for TC rule duplication.
 - Changes to LAG logic to enable its use when SR-IOV is enabled
 - PFs in switchdev mode is the only mode currently supported.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Paolo Abeni says:

====================
net: mitigate retpoline overhead

The spectre v2 counter-measures, aka retpolines, are a source of measurable
overhead[1]. We can partially address that when the function pointer refers to
a builtin symbol resorting to a list of tests vs well-known builtin function and
direct calls.

Experimental results show that replacing a single indirect call via
retpoline with several branches and a direct call gives performance gains
even when multiple branches are added - 5 or more, as reported in [2].

This may lead to some uglification around the indirect calls. In netconf 2018
Eric Dumazet described a technique to hide the most relevant part of the needed
boilerplate with some macro help.

This series is a [re-]implementation of such idea, exposing the introduced
helpers in a new header file. They are later leveraged to avoid the indirect
call overhead in the GRO path, when possible.

Overall this gives > 10% performance improvement for UDP GRO benchmark and
smaller but measurable for TCP syn flood.

The added infra can be used in follow-up patches to cope with retpoline overhead
in other points of the networking stack (e.g. at the qdisc layer) and possibly
even in other subsystems.

v2  -> v3:
 - fix build error with CONFIG_IPV6=m

v1  -> v2:
 - list explicitly the builtin function names in INDIRECT_CALL_*(),
   as suggested by Ed Cree
 - expand the recipients list

rfc -> v1:
 - use branch prediction hints, as suggested by Eric

[1] http://vger.kernel.org/netconf2018_files/PaoloAbeni_netconf2018.pdf
[2] https://linuxplumbersconf.org/event/2/contributions/99/attachments/98/117/lpc18_paper_af_xdp_perf-v2.pdf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This avoids another indirect call for UDP GRO. Again, the test
for the IPv6 variant is performed first.

v1 -> v2:
 - adapted to INDIRECT_CALL_ changes
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This avoids an indirect call in the receive path for TCP and UDP
packets. TCP takes precedence on UDP, so that we have a single
additional conditional in the common case.

When IPV6 is build as module, all gro symbols except UDPv6 are
builtin, while the latter belong to the ipv6 module, so we
need some special care.

v1 -> v2:
 - adapted to INDIRECT_CALL_ changes
v2 -> v3:
 - fix build issue with CONFIG_IPV6=m
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This avoids an indirect calls for L3 GRO receive path, both
for ipv4 and ipv6, if the latter is not compiled as a module.

Note that when IPv6 is compiled as builtin, it will be checked first,
so we have a single additional compare for the more common path.

v1 -> v2:
 - adapted to INDIRECT_CALL_ changes
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This header define a bunch of helpers that allow avoiding the
retpoline overhead when calling builtin functions via function pointers.
It boils down to explicitly comparing the function pointers to
known builtin functions and eventually invoke directly the latter.

The macros defined here implement the boilerplate for the above schema
and will be used by the next patches.

rfc -> v1:
 - use branch prediction hint, as suggested by Eric
v1  -> v2:
 - list explicitly the builtin function names in INDIRECT_CALL_*(),
   as suggested by Ed Cree
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the driver issues 2 mmio reads to figure out the number of
transmitted packets and clean them. We can get rid of the expensive
reads since BIT 31 of the Tx descriptor can be used for that.
We can also remove the budget counting of Tx completions since all of
the descriptors are not deliberately processed.

Performance numbers using pktgen are:
size  pre-patch(pps)  post-patch(pps)
64       362483           427916
128      358315           411686
256      352725           389683
512      215675           216464
1024     113812           114442
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Running pktgen with packets sizes > 512b ends up in the interface Txq
getting stuck.
"netsec 522d0000.ethernet eth0: netsec_netdev_start_xmit: TxQFull!"
appears on dmesg but the interface never recovers. It requires an
ifconfig down/up to make the interface usable again.

The reason that triggers this, is a race condition between
.ndo_start_xmit and the napi completion. The available budget is
calculated first and indicates the queue is full. Due to a costly
netif_err() the queue is not stopped in time while the napi completion
runs, clears the irq and frees up descriptors, thus the queue never wakes
up again.

Fix this by moving the print after stopping the queue, make the print
ratelimited, add barriers and check for cleaned descriptors..
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Document RZ/G2E (R8A774C0) SoC bindings.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move arp_queue_len_bytes ahead of arp_queue to remove two 4-byte holes.
Ensure ha element is always 8-byte aligned.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Except for returning, the var leaf is not
used in the qdisc_leaf(). For simplicity, remove it.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A recent commit allows sockets bound to a VRF to receive ipv6 link local
packets. However, it only works for UDP and worse TCP connection attempts
to the LLA with the only listener bound to the VRF just hang where as
before the client gets a reset and connection refused. Fix by adjusting
ir_iif for LL addresses and packets received through a device enslaved
to a VRF.

Fixes: 6f12fa77 ("vrf: mark skb for multicast or link-local as enslaved to VRF")
Reported-by: Donald Sharp <sharpd@cumulusnetworks.com>
Cc: Mike Manning <mmanning@vyatta.att-mail.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Improve detection of spurious interrupts by checking against the
interrupt mask as currently set in the chip.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We already have the DEFINE_SHOW_ATTRIBUTE. There is no need to define
such a macro, so remove DEFINE_SIMPLE_DEBUGFS_FILE. Also use the
DEFINE_SHOW_ATTRIBUTE macro to simplify some code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Salil Mehta says:

====================
net: hns3: Add more commands to Debugfs in HNS3 driver

This patch-set adds few more debugfs commands to HNS3 Ethernet
Driver. Support has been added to query info related to below
items:
1. Packet buffer descriptor ("echo bd info [queue no] [bd index] > cmd")
2. Manager table("echo dump mng tbl > cmd")
3. Dfx status register("echo dump reg ssu [prt id] > cmd")
4. Dcb status register("echo dump reg dcb [port id] > cmd")
5. Queue map ("echo queue map [queue no] > cmd")
6. Tm map ("echo tm map [queue no] > cmd")

NOTE: Above commands are *read-only* and are only intended to
query the information from the SoC(and dump inside the kernel,
for now) and in no way tries to perform write operations for
the purpose of configuration etc.

Change Log:
V1-->V2:
1. Addressed the GCC-8.2 compiler issue reported by David S. Miller.
   Link: https://lkml.org/lkml/2018/12/14/1298
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch prints dcb register status  information by module.

debugfs command:
root@(none)# echo dump tm map 100 > cmd
queue_id | qset_id | pri_id | tc_id
0100     | 0065    | 08     | 00
root@(none)#
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>