The threshold should be greater than clustersize and less than i_size.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

We're going to support partial extent moving, which may split entire extent
movement into pieces to compromise the insuffice allocations, it eases the
'ENSPC' pain and makes the whole moving much less likely to fail, the downside
is it may make the fs even more fragmented before moving, just let the userspace
make a trade-off here.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

the basic logic of moving extents for a file is pretty like punching-hole
sequence, walk the extents within the range as user specified, calculating
an appropriate len to defrag/move, then let ocfs2_defrag/move_extent() to
do the actual moving.

This func ends up setting 'OCFS2_MOVE_EXT_FL_COMPLETE' to userpace if operation
gets done successfully.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

The helper is to calculate the defrag length in one run according to a threshold,
it will proceed doing defragmentation until the threshold was meet, and skip a
LARGE extent if any.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

ocfs2_move_extent() logic will validate the goal_offset_in_block,
where extents to be moved, what's more, it also compromises a bit
to probe the appropriate region around given goal_offset when the
original goal is not able to fit the movement.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

These helpers were actually borrowed from alloc.c, which may be publicized
later.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

Before doing the movement of extents, we'd better probe the alloc group from
'goal_blk' for searching a contiguous region to fit the wanted movement, we
even will have a best-effort try by compromising to a threshold around the
given goal.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

First best-effort attempt to validate and adjust the goal (physical address in
block), while it can't guarantee later operation can succeed all the time since
global_bitmap may change a bit over time.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

This function tries locate the right alloc group, where a given physical block
resides, it returns the caller a buffer_head of victim group descriptor, and also
the offset of block in this group, by passing the block number.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

It's a relatively complete function to accomplish defragmentation for entire
or partial extent, one journal handle was kept during the operation, it was
logically doing one more thing than ocfs2_move_extent() acutally, yes, it's
claiming the new clusters itself;-)
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

The moving range of __ocfs2_move_extent() was within one extent always, it
consists following parts:

1. Duplicates the clusters in pages to new_blkoffset, where extent to be moved.

2. Split the original extent with new extent, coalecse the nearby extents if possible.

3. Append old clusters to truncate log, or decrease_refcount if the extent was refcounted.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

Ocfs2/move_extents: lock allocators and reserve metadata blocks and data clusters for extents moving.

ocfs2_lock_allocators_move_extents() was like the common ocfs2_lock_allocators(),
to lock metadata and data alloctors during extents moving, reserve appropriate
metadata blocks and data clusters, also performa a best- effort to calculate the
credits for journal transaction in one run of movement.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

Adding new files move_extents.[c|h] and fill it with nothing but
only a context structure.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

Patch also manages to add a manipulative struture for this ioctl.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

The original goal of commonizing these funcs is to benefit defraging/extent_moving
codes in the future,  based on the fact that reflink and defragmentation having
the same Copy-On-Wrtie mechanism.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

This new code is a bit more complicated than former ones, the goal is to
show user all statistics required to take a deep insight into filesystem
on how the disk is being fragmentaed.

The goal is achieved by scaning global bitmap from (cluster)group to group
to figure out following factors in the filesystem:

        - How many free chunks in a fixed size as user requested.
        - How many real free chunks in all size.
        - Min/Max/Avg size(in) clusters of free chunks.
        - How do free chunks distribute(in size) in terms of a histogram,
          just like following:
          ---------------------------------------------------------
          Extent Size Range :  Free extents  Free Clusters  Percent
             32K...   64K-  :             1             1    0.00%
              1M...    2M-  :             9           288    0.03%
              8M...   16M-  :             2           831    0.09%
             32M...   64M-  :             1          2047    0.23%
            128M...  256M-  :             1          8191    0.92%
            256M...  512M-  :             2         21706    2.43%
            512M... 1024M-  :            27        858623   96.29%
          ---------------------------------------------------------

Userspace ioctl() call eventually gets the above info returned by passing
a 'struct ocfs2_info_freefrag' with the chunk_size being specified first.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

The new code is dedicated to calculate free inodes number of all inode_allocs,
then return the info to userpace in terms of an array.

Specially, flag 'OCFS2_INFO_FL_NON_COHERENT', manipulated by '--cluster-coherent'
from userspace, is now going to be involved. setting the flag on means no cluster
coherency considered, usually, userspace tools choose none-coherency strategy by
default for the sake of performace.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

It just removes some macros for the sake of typechecking gains.
Signed-off-by: Tristan Ye <tristan.ye@oracle.com>

* 'for-linus/2640/i2c' of git://git.fluff.org/bjdooks/linux: (21 commits)
  mach-ux500: set proper I2C platform data from MOP500s
  i2c-nomadik: break out single messsage transmission
  i2c-nomadik: reset the hw after status check
  i2c-nomadik: remove the unnecessary delay
  i2c-nomadik: change the TX and RX threshold
  i2c-nomadik: add code to retry on timeout failure
  i2c-nomadik: use pm_runtime API
  i2c-nomadik: print abort cause only on abort tag
  i2c-nomadik: correct adapter timeout initialization
  i2c-nomadik: remove the redundant error message
  i2c-nomadik: corrrect returned error numbers
  i2c-nomadik: fix speed enumerator
  i2c-nomadik: make i2c timeout specific per i2c bus
  i2c-nomadik: add regulator support
  i2c: i2c-sh_mobile bus speed platform data V2
  i2c: i2c-sh_mobile clock string removal
  i2c-eg20t: Support new device ML7223 IOH
  i2c: tegra: Add de-bounce cycles.
  i2c: tegra: fix repeated start handling
  i2c: tegra: recover from spurious interrupt storm
  ...

Merge branches 'for-2639/i2c-eg20t', 'for-2639/i2c-shmobile', 'for-2639/i2c-tegra' and 'for-2639/i2c-nomadik2' into for-linus/2640/i2c

This specifies the new per-platform timeout per I2C bus and
switches the I2C buses to fast mode, and increase the FIFO
depth to 8 for reads and writes.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Reduce code size in the message transfer function by factoring out
a single-message transfer function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

In case of I2C timeout, reset the HW only after the HW status
is read, otherwise the staus will be lost.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The delay in the driver seems to be not needed, so remove it.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Markus Grape <markus.grape@stericsson.com>
Tested-by: Per Persson <per.xb.persson@stericsson.com>
Tested-by: Chethan Krishna N <chethan.krishna@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

1) Increase RX FIFO threshold so that there is a reduction in
the number of interrupts handled to complete a transaction.

2) Fill TX FIFO in the write function.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

It is seen that i2c-nomadik controller randomly stops generating the
interrupts leading to a i2c timeout. As a workaround to this problem,
add retries to the on going transfer on failure.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Use the pm_runtime API for pins control.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
[deleted some surplus runtime PM code]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Modify the code to:
1)Print the cause of i2c failure only if the status is set to ABORT.
2)Print slave address on send/receive fail, will help in which slave
failed.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Correct the incorrect initialization of adapter timeout not to be
in milliseconds, as it needs to be done in jiffies.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The abort cause string itself is an error, so remove the redundant
explicit error message.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The code was returning bad error numbers or just -1 in some cases.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

The I2C speed enumerators in the i2c-nomadik header file were in
the wrong order.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

Add option to have different i2c timeout delay for different i2c buses
specified in platform data. Default to the old value unless specified.
Signed-off-by: Virupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

This on-chip I2C controller needs to fetch the regulator
representing its voltage domain so that it won't be switched off.
Signed-off-by: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c-parport: Various cleanups
  i2c-i801: Don't depend on other kernel driver config options
  i2c-i801: Check for vendor Fujitsu before probing for apanel
  i2c-i801: Don't probe for slaves on IDF channels
  i2c-i801: SMBus patch for Intel Panther Point DeviceIDs
  i2c/writing-clients: Fix foo_driver.id_table

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6:
  jbd: Fix comment to match the code in journal_start()
  jbd/jbd2: remove obsolete summarise_journal_usage.
  jbd: Fix forever sleeping process in do_get_write_access()
  ext2: fix error msg when mounting fs with too-large blocksize
  jbd: fix fsync() tid wraparound bug
  ext3: Fix fs corruption when make_indexed_dir() fails
  ext3: Fix lock inversion in ext3_symlink()

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/dlm:
  dlm: make plock operation killable
  dlm: remove shared message stub for recovery
  dlm: delayed reply message warning
  dlm: Remove superfluous call to recalc_sigpending()

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (43 commits)
  TOMOYO: Fix wrong domainname validation.
  SELINUX: add /sys/fs/selinux mount point to put selinuxfs
  CRED: Fix load_flat_shared_library() to initialise bprm correctly
  SELinux: introduce path_has_perm
  flex_array: allow 0 length elements
  flex_arrays: allow zero length flex arrays
  flex_array: flex_array_prealloc takes a number of elements, not an end
  SELinux: pass last path component in may_create
  SELinux: put name based create rules in a hashtable
  SELinux: generic hashtab entry counter
  SELinux: calculate and print hashtab stats with a generic function
  SELinux: skip filename trans rules if ttype does not match parent dir
  SELinux: rename filename_compute_type argument to *type instead of *con
  SELinux: fix comment to state filename_compute_type takes an objname not a qstr
  SMACK: smack_file_lock can use the struct path
  LSM: separate LSM_AUDIT_DATA_DENTRY from LSM_AUDIT_DATA_PATH
  LSM: split LSM_AUDIT_DATA_FS into _PATH and _INODE
  SELINUX: Make selinux cache VFS RCU walks safe
  SECURITY: Move exec_permission RCU checks into security modules
  SELinux: security_read_policy should take a size_t not ssize_t
  ...

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  kbuild: make KBUILD_NOCMDDEP=1 handle empty built-in.o
  scripts/kallsyms.c: fix potential segfault
  scripts/gen_initramfs_list.sh: Convert to a /bin/sh script
  kbuild: Fix GNU make v3.80 compatibility
  kbuild: Fix passing -Wno-* options to gcc 4.4+
  kbuild: move scripts/basic/docproc.c to scripts/docproc.c
  kbuild: Fix Makefile.asm-generic for um
  kbuild: Allow to combine multiple W= levels
  kbuild: Disable -Wunused-but-set-variable for gcc 4.6.0
  Fix handling of backlash character in LINUX_COMPILE_BY name
  kbuild: asm-generic support
  kbuild: implement several W= levels
  kbuild: Fix build with binutils <= 2.19
  initramfs: Use KBUILD_BUILD_TIMESTAMP for generated entries
  kbuild: Allow to override LINUX_COMPILE_BY and LINUX_COMPILE_HOST macros
  kbuild: Drop unused LINUX_COMPILE_TIME and LINUX_COMPILE_DOMAIN macros
  kbuild: Use the deterministic mode of ar
  kbuild: Call gzip with -n
  kbuild: move KALLSYMS_EXTRA_PASS from Kconfig to Makefile
  Kconfig: improve KALLSYMS_ALL documentation

Fix up trivial conflict in Makefile

* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6:
  pcmcia: Make struct pcmcia_device_id const, sound drivers edition
  staging: pcmcia: Convert pcmcia_device_id declarations to const
  pcmcia: Convert pcmcia_device_id declarations to const
  pcmcia: Make declaration and uses of struct pcmcia_device_id const
  pcmcia/sa1100: put sa11x0_pcmcia_hw_init[] to .devinit.data