- 04 Oct, 2010 1 commit
-
-
stephen hemminger authored
This table is only used in gre.c Signed-off-by:
Stephen Hemminger <shemminger@vyatta.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
- 01 Oct, 2010 29 commits
-
-
Vasanthy Kolluri authored
Update MAINTAINERS list Signed-off-by:
Vasanthy Kolluri <vkolluri@cisco.com> Signed-off-by:
Roopa Prabhu <roprabhu@cisco.com> Signed-off-by:
David Wang <dwang2@cisco.com> Signed-off-by:
-
Vasanthy Kolluri authored
Make functions used locally in a file as static Signed-off-by:
-
Vasanthy Kolluri authored
Removed code that is unused Signed-off-by:
-
Eric Dumazet authored
On 64bit arches, there are two 32bit holes that we can remove. sizeof(struct neighbour) shrinks from 0xf8 to 0xf0 bytes Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Tilman Schmidt authored
Rephrase some USB error messages to make them clearer and more consistent. Downgrade some warning messages that may occur during normal operation to debug messages. Signed-off-by:
Tilman Schmidt <tilman@imap.cc> Signed-off-by:
-
Tilman Schmidt authored
Rework the handling of USB errors in interrupt input reads to clear halts correctly, delay URB resubmission after errors, limit retries, and improve error recovery. Signed-off-by:
-
Tilman Schmidt authored
Recover from a lost HD_RECEIVEATDATA_ACK message by sending a zero-length HD_READ_ATMESSAGE command when ev_layer sends "+++". Signed-off-by:
-
Tilman Schmidt authored
In error_reset(), if sending HD_RESET_INTERRUPT_PIPE to the device fails, try performing an USB reset. Also correct an error in the leading comment. Signed-off-by:
-
Tilman Schmidt authored
Use setup_timer() and mod_timer() instead of direct assignment to timer structure members, simplify the argument of one timer routine, and make extra sure all timers are stopped during suspend. Signed-off-by:
-
Tilman Schmidt authored
Remove the debug flag DEBUG_DRIVER and associated code. It doesn't serve any useful purpose anymore. Signed-off-by:
-
Tilman Schmidt authored
In transparent data reception, avoid a NULL pointer dereference in case an skbuff cannot be allocated, remove an inappropriate call to the HDLC flush routine, and correct the accounting of received bytes for continued buffers. Signed-off-by:
-
Tilman Schmidt authored
Rework the handling of USB errors in AT response reads to fix a possible infinite retry loop and a memory leak, and silence a few overly verbose kernel messages. Signed-off-by:
-
Tilman Schmidt authored
Unlock cs->lock before calling error_hangup() which is marked "cs->lock must not be held". Signed-off-by:
-
Matt Carlson authored
This patch updates the tg3 version to 3.114. Signed-off-by:
Matt Carlson <mcarlson@broadcom.com> Reviewed-by:
Michael Chan <mchan@broadcom.com> Signed-off-by:
-
Matt Carlson authored
This patch increases the rx ring sizes for those asic revs that support them. Signed-off-by:
-
Matt Carlson authored
This patch adds two new variables to track the size of the standard and jumbo rx producer ring sizes. The code is then pivoted to these variables from preprocessor constants. Signed-off-by:
-
Matt Carlson authored
There are other multiqueue modes 5717 and 5719 devices can assume. This patch makes sure that the loopback test is safe, should those other modes be enabled in the future. Signed-off-by:
-
Matt Carlson authored
This patch cleans up the default VPD partno section. New entries for 5717 asic rev devices were also added. Signed-off-by:
-
Matt Carlson authored
This product was never released to the public. Signed-off-by:
-
Matt Carlson authored
This patch enables a bit that prevents read DMA overflows and adjusts the txmbuf margin from the hardware default. The combination of these modifications prevents a tx data corruption issue we were seeing on the 5719. Signed-off-by:
-
Matt Carlson authored
Up until now the tg3 driver would call netif_napi_add() for the maximum number of NAPI instances the driver could use. The problem is that netpoll could call tg3_poll() on instances that are not active. The net effect is that the driver will crash attempting to dereference uninitialized pointers. The fix is to only allocate as many NAPI instances as the driver would use in tg3_open() and deleted them in tg3_close(). Signed-off-by:
-
Eric Dumazet authored
ip_route_output_slow() is enclosed in an rcu_read_lock() protected section, so that no references are taken/released on device, thanks to __ip_dev_find() & dev_get_by_index_rcu() Tested with ip route cache disabled, and a stress test : Before patch: elapsed time : real 1m38.347s user 0m11.909s sys 23m51.501s Profile: 13788.00 22.7% ip_route_output_slow [kernel] 7875.00 13.0% dst_destroy [kernel] 3925.00 6.5% fib_semantic_match [kernel] 3144.00 5.2% fib_rules_lookup [kernel] 3061.00 5.0% dst_alloc [kernel] 2276.00 3.7% rt_set_nexthop [kernel] 1762.00 2.9% fib_table_lookup [kernel] 1538.00 2.5% _raw_read_lock [kernel] 1358.00 2.2% ip_output [kernel] After patch: real 1m28.808s user 0m13.245s sys 20m37.293s 10950.00 17.2% ip_route_output_slow [kernel] 10726.00 16.9% dst_destroy [kernel] 5170.00 8.1% fib_semantic_match [kernel] 3937.00 6.2% dst_alloc [kernel] 3635.00 5.7% rt_set_nexthop [kernel] 2900.00 4.6% fib_rules_lookup [kernel] 2240.00 3.5% fib_table_lookup [kernel] 1427.00 2.2% _raw_read_lock [kernel] 1157.00 1.8% kmem_cache_alloc [kernel] Signed-off-by:
-
Eric Dumazet authored
ip_dev_find(net, addr) finds a device given an IPv4 source address and takes a reference on it. Introduce __ip_dev_find(), taking a third argument, to optionally take the device reference. Callers not asking the reference to be taken should be in an rcu_read_lock() protected section. Signed-off-by:
-
Bruce Allan authored
The initial support for 82579 was tuned poorly for performance. Adjust the packet buffer allocation appropriately for both standard and jumbo frames; and for jumbo frames increase the receive descriptor pre-fetch, disable adaptive interrupt moderation and set the DMA latency tolerance. Signed-off-by:
Bruce Allan <bruce.w.allan@intel.com> Tested-by:
Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by:
-
Jesse Brandeburg authored
Most e1000e parts support batching writebacks. The problem with this is that when some of the TADV or TIDV timers are not set, Tx can sit forever. This is solved in this patch with write flushes using the Flush Partial Descriptors (FPD) bit in TIDV and RDTR. This improves bus utilization and removes partial writes on e1000e, particularly from 82571 parts in S5500 chipset based machines. Only ES2LAN and 82571/2 parts are included in this optimization, to reduce testing load. Signed-off-by:
Jesse Brandeburg <jesse.brandeburg@intel.com> Tested-by:
Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by:
-
Emil Tantilov authored
Fix possible panic/hang with shared Legacy interrupts by not enabling interrupts when interface is down. Also fixes an intermittent link by enabling LSC upon exit from ixgbe_intr() This patch adds flags to ixgbe_irq_enable() to allow for some flexibility when enabling interrupts. Signed-off-by:
Stephen Ko <stephen.s.ko@intel.com> Signed-off-by:
-
Eric Dumazet authored
While doing stress tests with a disabled IP route cache, I found __mkroute_output() was touching three times in_device atomic refcount. Use RCU to touch it once to reduce cache line ping pongs. Before patch time to perform the test real 1m42.009s user 0m12.545s sys 25m0.726s Profile : 16109.00 26.4% ip_route_output_slow vmlinux 7434.00 12.2% dst_destroy vmlinux 3280.00 5.4% fib_rules_lookup vmlinux 3252.00 5.3% fib_semantic_match vmlinux 2622.00 4.3% fib_table_lookup vmlinux 2535.00 4.1% dst_alloc vmlinux 1750.00 2.9% _raw_read_lock vmlinux 1532.00 2.5% rt_set_nexthop vmlinux After patch real 1m36.503s user 0m12.977s sys 23m25.608s 14234.00 22.4% ip_route_output_slow vmlinux 8717.00 13.7% dst_destroy vmlinux 4052.00 6.4% fib_rules_lookup vmlinux 3951.00 6.2% fib_semantic_match vmlinux 3191.00 5.0% dst_alloc vmlinux 1764.00 2.8% fib_table_lookup vmlinux 1692.00 2.7% _raw_read_lock vmlinux 1605.00 2.5% rt_set_nexthop vmlinux Signed-off-by:
-
Rémi Denis-Courmont authored
This patch restores the below flow control patch submitted by Rémi Denis-Courmont, which accidentaly got lost due to Pipe controller patch on Phonet. commit 1a98214f Author: Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Date: Mon Aug 30 12:57:03 2010 +0000 Phonet: restore flow control credits when sending fails Signed-off-by:
Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by:
Kumar Sanghvi <kumar.sanghvi@stericsson.com> Acked-by:
Linus Walleij <linus.walleij@stericsson.com> Signed-off-by:
-
Philip Rakity authored
Signed-off-by:
Philip Rakity <prakity@marvell.com> Signed-off-by:
Sachin Sanap <ssanap@marvell.com> Signed-off-by:
Mark Brown <markb@marvell.com> Signed-off-by:
-
- 30 Sep, 2010 7 commits
-
-
Eric Dumazet authored
HARD_TX_LOCK no longer protects tunnels from dead loops, but xmit_recursion percpu counter. Signed-off-by:
-
Ondrej Zary authored
It should be ready after 8 years...remove the experimental dependency. Signed-off-by:
Ondrej Zary <linux@rainbow-software.org> Acked-by:
Jeff Garzik <jgarzik@redhat.com> Signed-off-by:
-
Ondrej Zary authored
Print media debug messages only when HW debug is enabled. Signed-off-by:
-
Andrew Gallatin authored
This patch contains the following DCA improvements to myri10ge: 1) Finally move myri10ge to use dca3 API 2) Disable PCIe relaxed ordering when enabling DCA on myri10ge. This provides a performance boost on Nehalem based Xeons 3) Make sure to properly initialize NIC's DCA state when it is enabled, rather than giving the NIC a bogus tag (0) and waiting for the first received packet to trigger an update. Not using a real tag can cause hardware exceptions on some motherboards when a CPU socket is empty. 3) Always update the cached CPU when our interrupt affinity changes so as to avoid excessive calls to dca3_get_tag() Signed-off-by:Andrew Gallatin <gallatin@myri.com> Signed-off-by:
Loic Prylli <loic@myri.com> Signed-off-by:
-
Dmitry Kravkov authored
Moved enabling of MSI to the bnx2x_set_num_queues() - the same functions that handles the initialization of the MSI-X. From: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by:
Dmitry Kravkov <dmitry@broadcom.com> Signed-off-by:
Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by:
Eilon Greenstein <eilong@broadcom.com> Signed-off-by:
-
stephen hemminger authored
Function only used in tcp_input.c Signed-off-by:
-
stephen hemminger authored
arp_broken_ops is only used in arp.c Signed-off-by:
-
- 29 Sep, 2010 3 commits
-
-
Eric Dumazet authored
There is some confusion with rx_queue name after RPS, and net drivers private rx_queue fields. I suggest to rename "struct net_device"->rx_queue to ingress_queue. Signed-off-by:
-
Eric Dumazet authored
Maintain per_cpu tx_bytes, tx_packets, rx_bytes, rx_packets. Other seldom used fields are kept in netdev->stats structure, possibly unsafe. This is a preliminary work to support lockless transmit path, and correct RX stats, that are already unsafe. Signed-off-by:
-
Eric Dumazet authored
IPIP tunnels can benefit from lockless xmits, using NETIF_F_LLTX Bench on a 16 cpus machine (dual E5540 cpus), 16 threads sending 10000000 UDP frames via one ipip tunnel (size:200 bytes per frame) Before patch : real 2m53.321s user 0m10.277s sys 46m0.597s After patch: real 0m32.063s user 0m9.237s sys 8m16.255s Last problem to solve is the contention on dst : 16118.00 28.3% __ip_route_output_key vmlinux 6135.00 10.8% dst_release vmlinux 3220.00 5.6% ip_finish_output vmlinux 2149.00 3.8% ip_route_output_flow vmlinux 1575.00 2.8% ip_append_data vmlinux 1481.00 2.6% ip_push_pending_frames vmlinux 1349.00 2.4% __xfrm_lookup vmlinux 1216.00 2.1% csum_partial_copy_generic vmlinux 1208.00 2.1% udp_sendmsg vmlinux Signed-off-by:
-
