- 20 Feb, 2019 40 commits
-
-
Nate Dailey authored
commit dfcc34c9 upstream. sync_request_write no longer submits writes to a Faulty device. This has the unfortunate side effect that bitmap bits can be incorrectly cleared if a recovery is interrupted (previously, end_sync_write would have prevented this). This means the next recovery may not copy everything it should, potentially corrupting data. Add a function for doing the proper md_bitmap_end_sync, called from end_sync_write and the Faulty case in sync_request_write. backport note to 4.14: s/md_bitmap_end_sync/bitmap_end_sync Cc: stable@vger.kernel.org 4.14+ Fixes: 0c9d5b12 ("md/raid1: avoid reusing a resync bio after error handling.") Reviewed-by:
Jack Wang <jinpu.wang@cloud.ionos.com> Tested-by:
Nate Dailey <nate.dailey@stratus.com> Signed-off-by:
Song Liu <songliubraving@fb.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Eric W. Biederman authored
commit cf43a757 upstream. In the middle of do_exit() there is there is a call "ptrace_event(PTRACE_EVENT_EXIT, code);" That call places the process in TACKED_TRACED aka "(TASK_WAKEKILL | __TASK_TRACED)" and waits for for the debugger to release the task or SIGKILL to be delivered. Skipping past dequeue_signal when we know a fatal signal has already been delivered resulted in SIGKILL remaining pending and TIF_SIGPENDING remaining set. This in turn caused the scheduler to not sleep in PTACE_EVENT_EXIT as it figured a fatal signal was pending. This also caused ptrace_freeze_traced in ptrace_check_attach to fail because it left a per thread SIGKILL pending which is what fatal_signal_pending tests for. This difference in signal state caused strace to report strace: Exit of unknown pid NNNNN ignored Therefore update the signal handling state like dequeue_signal would when removing a per thread SIGKILL, by removing SIGKILL from the per thread signal mask and clearing TIF_SIGPENDING. Acked-by:
Oleg Nesterov <oleg@redhat.com> Reported-by:
Ivan Delalande <colona@arista.com> Cc: stable@vger.kernel.org Fixes: 35634ffa ("signal: Always notice exiting tasks") Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
James Bottomley authored
commit e4a05698 upstream. The problem is that the default for MQ is not to gather entropy, whereas the default for the legacy queue was always to gather it. The original attempt to fix entropy gathering for rotational disks under MQ added an else branch in sd_read_block_characteristics(). Unfortunately, the entire check isn't reached if the device has no characteristics VPD page. Since this page was only introduced in SBC-3 and its optional anyway, most less expensive rotational disks don't have one, meaning they all stopped gathering entropy when we made MQ the default. In a wholly unrelated change, openssl and openssh won't function until the random number generator is initialised, meaning lots of people have been seeing large delays before they could log into systems with default MQ kernels due to this lack of entropy, because it now can take tens of minutes to initialise the kernel random number generator. The fix is to set the non-rotational and add-randomness flags unconditionally early on in the disk initialization path, so they can be reset only if the device actually reports being non-rotational via the VPD page. Reported-by:
Mikael Pettersson <mikpelinux@gmail.com> Fixes: 83e32a59 ("scsi: sd: Contribute to randomness when running rotational device") Cc: stable@vger.kernel.org Signed-off-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Reviewed-by:
Jens Axboe <axboe@kernel.dk> Reviewed-by:
Xuewei Zhang <xueweiz@google.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Hedi Berriche authored
commit f331e766 upstream. Calls into UV firmware must be protected against concurrency, expose the efi_runtime_lock to the UV platform, and use it to serialise UV BIOS calls. Signed-off-by:
Hedi Berriche <hedi.berriche@hpe.com> Signed-off-by:
Borislav Petkov <bp@suse.de> Reviewed-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Reviewed-by:
Russ Anderson <rja@hpe.com> Reviewed-by:
Dimitri Sivanich <sivanich@hpe.com> Reviewed-by:
Mike Travis <mike.travis@hpe.com> Cc: Andy Shevchenko <andy@infradead.org> Cc: Bhupesh Sharma <bhsharma@redhat.com> Cc: Darren Hart <dvhart@infradead.org> Cc: "H. Peter Anvin" <hpa@zytor.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: linux-efi <linux-efi@vger.kernel.org> Cc: platform-driver-x86@vger.kernel.org Cc: stable@vger.kernel.org # v4.9+ Cc: Steve Wahl <steve.wahl@hpe.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: x86-ml <x86@kernel.org> Link: https://lkml.kernel.org/r/20190213193413.25560-5-hedi.berriche@hpe.comSigned-off-by:
-
Andreas Ziegler authored
commit 0722069a upstream. When printing multiple uprobe arguments as strings the output for the earlier arguments would also include all later string arguments. This is best explained in an example: Consider adding a uprobe to a function receiving two strings as parameters which is at offset 0xa0 in strlib.so and we want to print both parameters when the uprobe is hit (on x86_64): $ echo 'p:func /lib/strlib.so:0xa0 +0(%di):string +0(%si):string' > \ /sys/kernel/debug/tracing/uprobe_events When the function is called as func("foo", "bar") and we hit the probe, the trace file shows a line like the following: [...] func: (0x7f7e683706a0) arg1="foobar" arg2="bar" Note the extra "bar" printed as part of arg1. This behaviour stacks up for additional string arguments. The strings are stored in a dynamically growing part of the uprobe buffer by fetch_store_string() after copying them from userspace via strncpy_from_user(). The return value of strncpy_from_user() is then directly used as the required size for the string. However, this does not take the terminating null byte into account as the documentation for strncpy_from_user() cleary states that it "[...] returns the length of the string (not including the trailing NUL)" even though the null byte will be copied to the destination. Therefore, subsequent calls to fetch_store_string() will overwrite the terminating null byte of the most recently fetched string with the first character of the current string, leading to the "accumulation" of strings in earlier arguments in the output. Fix this by incrementing the return value of strncpy_from_user() by one if we did not hit the maximum buffer size. Link: http://lkml.kernel.org/r/20190116141629.5752-1-andreas.ziegler@fau.de Cc: Ingo Molnar <mingo@redhat.com> Cc: stable@vger.kernel.org Fixes: 5baaa59e ("tracing/probes: Implement 'memory' fetch method for uprobes") Acked-by:
Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by:
Andreas Ziegler <andreas.ziegler@fau.de> Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Harald Freudenberger authored
commit 8f9aca0c upstream. The older machines don't have the QCI instruction available. With support for up to 256 crypto cards the probing of each card has been extended to check card ids from 0 up to 255. For machines with QCI support there is a filter limiting the range of probed cards. The older machines (z196 and older) don't have this filter and so since support for 256 cards is in the driver all cards are probed. However, these machines also require to have the card id fit into 6 bits. Exceeding this limit results in a specification exception which happens on every kernel startup even when there is no crypto configured and used at all. This fix limits the range of probed crypto cards to 64 if there is no QCI instruction available to obey to the older ap architecture and so fixes the specification exceptions on z196 machines. Cc: stable@vger.kernel.org # v4.17+ Fixes: af4a7227 ("s390/zcrypt: Support up to 256 crypto adapters.") Signed-off-by:
Harald Freudenberger <freude@linux.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> Signed-off-by:
-
Meelis Roos authored
commit bfc91368 upstream. Eiger machine vector definition has nr_irqs 128, and working 2.6.26 boot shows SCSI getting IRQ-s 64 and 65. Current kernel boot fails because Symbios SCSI fails to request IRQ-s and does not find the disks. It has been broken at least since 3.18 - the earliest I could test with my gcc-5. The headers have moved around and possibly another order of defines has worked in the past - but since 128 seems to be correct and used, fix arch/alpha/include/asm/irq.h to have NR_IRQS=128 for Eiger. This fixes 4.19-rc7 boot on my Force Flexor A264 (Eiger subarch). Cc: stable@vger.kernel.org # v3.18+ Signed-off-by:
Meelis Roos <mroos@linux.ee> Signed-off-by:
Matt Turner <mattst88@gmail.com> Signed-off-by:
-
Sergei Trofimovich authored
commit 491af60f upstream. Fix page fault handling code to fixup r16-r18 registers. Before the patch code had off-by-two registers bug. This bug caused overwriting of ps,pc,gp registers instead of fixing intended r16,r17,r18 (see `struct pt_regs`). More details: Initially Dmitry noticed a kernel bug as a failure on strace test suite. Test passes unmapped userspace pointer to io_submit: ```c #include <err.h> #include <unistd.h> #include <sys/mman.h> #include <asm/unistd.h> int main(void) { unsigned long ctx = 0; if (syscall(__NR_io_setup, 1, &ctx)) err(1, "io_setup"); const size_t page_size = sysconf(_SC_PAGESIZE); const size_t size = page_size * 2; void *ptr = mmap(NULL, size, PROT_READ | PROT_WRITE, MAP_PRIVATE | MAP_ANONYMOUS, -1, 0); if (MAP_FAILED == ptr) err(1, "mmap(%zu)", size); if (munmap(ptr, size)) err(1, "munmap"); syscall(__NR_io_submit, ctx, 1, ptr + page_size); syscall(__NR_io_destroy, ctx); return 0; } ``` Running this test causes kernel to crash when handling page fault: ``` Unable to handle kernel paging request at virtual address ffffffffffff9468 CPU 3 aio(26027): Oops 0 pc = [<fffffc00004eddf8>] ra = [<fffffc00004edd5c>] ps = 0000 Not tainted pc is at sys_io_submit+0x108/0x200 ra is at sys_io_submit+0x6c/0x200 v0 = fffffc00c58e6300 t0 = fffffffffffffff2 t1 = 000002000025e000 t2 = fffffc01f159fef8 t3 = fffffc0001009640 t4 = fffffc0000e0f6e0 t5 = 0000020001002e9e t6 = 4c41564e49452031 t7 = fffffc01f159c000 s0 = 0000000000000002 s1 = 000002000025e000 s2 = 0000000000000000 s3 = 0000000000000000 s4 = 0000000000000000 s5 = fffffffffffffff2 s6 = fffffc00c58e6300 a0 = fffffc00c58e6300 a1 = 0000000000000000 a2 = 000002000025e000 a3 = 00000200001ac260 a4 = 00000200001ac1e8 a5 = 0000000000000001 t8 = 0000000000000008 t9 = 000000011f8bce30 t10= 00000200001ac440 t11= 0000000000000000 pv = fffffc00006fd320 at = 0000000000000000 gp = 0000000000000000 sp = 00000000265fd174 Disabling lock debugging due to kernel taint Trace: [<fffffc0000311404>] entSys+0xa4/0xc0 ``` Here `gp` has invalid value. `gp is s overwritten by a fixup for the following page fault handler in `io_submit` syscall handler: ``` __se_sys_io_submit ... ldq a1,0(t1) bne t0,4280 <__se_sys_io_submit+0x180> ``` After a page fault `t0` should contain -EFALUT and `a1` is 0. Instead `gp` was overwritten in place of `a1`. This happens due to a off-by-two bug in `dpf_reg()` for `r16-r18` (aka `a0-a2`). I think the bug went unnoticed for a long time as `gp` is one of scratch registers. Any kernel function call would re-calculate `gp`. Dmitry tracked down the bug origin back to 2.1.32 kernel version where trap_a{0,1,2} fields were inserted into struct pt_regs. And even before that `dpf_reg()` contained off-by-one error. Cc: Richard Henderson <rth@twiddle.net> Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru> Cc: linux-alpha@vger.kernel.org Cc: linux-kernel@vger.kernel.org Reported-and-reviewed-by:
"Dmitry V. Levin" <ldv@altlinux.org> Cc: stable@vger.kernel.org # v2.1.32+ Bug: https://bugs.gentoo.org/672040Signed-off-by:
Sergei Trofimovich <slyfox@gentoo.org> Signed-off-by:
-
Dave Chinner authored
commit a9a238e8 upstream. This reverts commit 172b06c3 ("mm: slowly shrink slabs with a relatively small number of objects"). This change changes the agressiveness of shrinker reclaim, causing small cache and low priority reclaim to greatly increase scanning pressure on small caches. As a result, light memory pressure has a disproportionate affect on small caches, and causes large caches to be reclaimed much faster than previously. As a result, it greatly perturbs the delicate balance of the VFS caches (dentry/inode vs file page cache) such that the inode/dentry caches are reclaimed much, much faster than the page cache and this drives us into several other caching imbalance related problems. As such, this is a bad change and needs to be reverted. [ Needs some massaging to retain the later seekless shrinker modifications.] Link: http://lkml.kernel.org/r/20190130041707.27750-3-david@fromorbit.com Fixes: 172b06c3 ("mm: slowly shrink slabs with a relatively small number of objects") Signed-off-by:
Dave Chinner <dchinner@redhat.com> Cc: Wolfgang Walter <linux@stwm.de> Cc: Roman Gushchin <guro@fb.com> Cc: Spock <dairinin@gmail.com> Cc: Rik van Riel <riel@surriel.com> Cc: Michal Hocko <mhocko@kernel.org> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Dave Chinner authored
commit 69056ee6 upstream. This reverts commit a76cf1a4 ("mm: don't reclaim inodes with many attached pages"). This change causes serious changes to page cache and inode cache behaviour and balance, resulting in major performance regressions when combining worklaods such as large file copies and kernel compiles. https://bugzilla.kernel.org/show_bug.cgi?id=202441 This change is a hack to work around the problems introduced by changing how agressive shrinkers are on small caches in commit 172b06c3 ("mm: slowly shrink slabs with a relatively small number of objects"). It creates more problems than it solves, wasn't adequately reviewed or tested, so it needs to be reverted. Link: http://lkml.kernel.org/r/20190130041707.27750-2-david@fromorbit.com Fixes: a76cf1a4 ("mm: don't reclaim inodes with many attached pages") Signed-off-by:
-
J. Bruce Fields authored
commit 3bf6b57e upstream. This reverts commit d6ebf508. I forgot that the kernel's default lease period should never be decreased! After a kernel upgrade, the kernel has no way of knowing on its own what the previous lease time was. Unless userspace tells it otherwise, it will assume the previous lease period was the same. So if we decrease this value in a kernel upgrade, we end up enforcing a grace period that's too short, and clients will fail to reclaim state in time. Symptoms may include EIO and log messages like "NFS: nfs4_reclaim_open_state: Lock reclaim failed!" There was no real justification for the lease period decrease anyway. Reported-by:
Donald Buczek <buczek@molgen.mpg.de> Fixes: d6ebf508 "nfsd4: return default lease period" Cc: stable@vger.kernel.org Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
Matti Kurkela authored
commit e8b22d0a upstream. Like Fujitsu CELSIUS H760, the H780 also has a three-button Elantech touchpad, but the driver needs to be told so to enable the middle touchpad button. The elantech_dmi_force_crc_enabled quirk was not necessary with the H780. Also document the fw_version and caps values detected for both H760 and H780 models. Signed-off-by:
Matti Kurkela <Matti.Kurkela@iki.fi> Cc: stable@vger.kernel.org Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Jonathan Bakker authored
commit 90cc55f0 upstream. Otherwise we introduce a race condition where userspace can request input before we're ready leading to null pointer dereference such as input: bma150 as /devices/platform/i2c-gpio-2/i2c-5/5-0038/input/input3 Unable to handle kernel NULL pointer dereference at virtual address 00000018 pgd = (ptrval) [00000018] *pgd=55dac831, *pte=00000000, *ppte=00000000 Internal error: Oops: 17 [#1] PREEMPT ARM Modules linked in: bma150 input_polldev [last unloaded: bma150] CPU: 0 PID: 2870 Comm: accelerometer Not tainted 5.0.0-rc3-dirty #46 Hardware name: Samsung S5PC110/S5PV210-based board PC is at input_event+0x8/0x60 LR is at bma150_report_xyz+0x9c/0xe0 [bma150] pc : [<80450f70>] lr : [<7f0a614c>] psr: 800d0013 sp : a4c1fd78 ip : 00000081 fp : 00020000 r10: 00000000 r9 : a5e2944c r8 : a7455000 r7 : 00000016 r6 : 00000101 r5 : a7617940 r4 : 80909048 r3 : fffffff2 r2 : 00000000 r1 : 00000003 r0 : 00000000 Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 10c5387d Table: 54e34019 DAC: 00000051 Process accelerometer (pid: 2870, stack limit = 0x(ptrval)) Stackck: (0xa4c1fd78 to 0xa4c20000) fd60: fffffff3 fc813f6c fd80: 40410581 d7530ce3 a5e2817c a7617f00 a5e29404 a5e2817c 00000000 7f008324 fda0: a5e28000 8044f59c a5fdd9d0 a5e2945c a46a4a00 a5e29668 a7455000 80454f10 fdc0: 80909048 a5e29668 a5fdd9d0 a46a4a00 806316d0 00000000 a46a4a00 801df5f0 fde0: 00000000 d7530ce3 a4c1fec0 a46a4a00 00000000 a5fdd9d0 a46a4a08 801df53c fe00: 00000000 801d74bc a4c1fec0 00000000 a4c1ff70 00000000 a7038da8 00000000 fe20: a46a4a00 801e91fc a411bbe0 801f2e88 00000004 00000000 80909048 00000041 fe40: 00000000 00020000 00000000 dead4ead a6a88da0 00000000 ffffe000 806fcae8 fe60: a4c1fec8 00000000 80909048 00000002 a5fdd9d0 a7660110 a411bab0 00000001 fe80: dead4ead ffffffff ffffffff a4c1fe8c a4c1fe8c d7530ce3 20000013 80909048 fea0: 80909048 a4c1ff70 00000001 fffff000 a4c1e000 00000005 00026038 801eabd8 fec0: a7660110 a411bab0 b9394901 00000006 a696201b 76fb3000 00000000 a7039720 fee0: a5fdd9d0 00000101 00000002 00000096 00000000 00000000 00000000 a4c1ff00 ff00: a6b310f4 805cb174 a6b310f4 00000010 00000fe0 00000010 a4c1e000 d7530ce3 ff20: 00000003 a5f41400 a5f41424 00000000 a6962000 00000000 00000003 00000002 ff40: ffffff9c 000a0000 80909048 d7530ce3 a6962000 00000003 80909048 ffffff9c ff60: a6962000 801d890c 00000000 00000000 00020000 a7590000 00000004 00000100 ff80: 00000001 d7530ce3 000288b8 00026320 000288b8 00000005 80101204 a4c1e000 ffa0: 00000005 80101000 000288b8 00026320 000288b8 000a0000 00000000 00000000 ffc0: 000288b8 00026320 000288b8 00000005 7eef3bac 000264e8 00028ad8 00026038 ffe0: 00000005 7eef3300 76f76e91 76f78546 800d0030 000288b8 00000000 00000000 [<80450f70>] (input_event) from [<a5e2817c>] (0xa5e2817c) Code: e1a08148 eaffffa8 e351001f 812fff1e (e590c018) ---[ end trace 1c691ee85f2ff243 ]--- Signed-off-by:
Jonathan Bakker <xc-racer2@live.ca> Signed-off-by:
Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Zachary Hays authored
commit dcf6e2e3 upstream. The kblockd workqueue is created with the WQ_MEM_RECLAIM flag set. This generates a rescuer thread for that queue that will trigger when the CPU is under heavy load and collect the uncompleted work. In the case of mmc, this creates the possibility of a deadlock when there are multiple partitions on the device as other blk-mq work is also run on the same queue. For example: - worker 0 claims the mmc host to work on partition 1 - worker 1 attempts to claim the host for partition 2 but has to wait for worker 0 to finish - worker 0 schedules complete_work to release the host - rescuer thread is triggered after time-out and collects the dangling work - rescuer thread attempts to complete the work in order starting with claim host - the task to release host is now blocked by a task to claim it and will never be called The above results in multiple hung tasks that lead to failures to mount partitions. Handling complete_work on a separate workqueue avoids this by keeping the work completion tasks separate from the other blk-mq work. This allows the host to be released without getting blocked by other tasks attempting to claim the host. Signed-off-by:
Zachary Hays <zhays@lexmark.com> Fixes: 81196976 ("mmc: block: Add blk-mq support") Cc: <stable@vger.kernel.org> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Chen-Yu Tsai authored
commit d6f11e7d upstream. The MMC device tree bindings include properties used to signal various signalling speed modes. Until now the sunxi driver was accepting them without any further filtering, while the sunxi device trees were not actually using them. Since some of the H5 boards can not run at higher speed modes stably, we are resorting to declaring the higher speed modes per-board. Regardless, having boards declare modes and blindly following them, even without proper support in the driver, is generally a bad thing. Filter out all unsupported modes from the capabilities mask after the device tree properties have been parsed. Cc: <stable@vger.kernel.org> Signed-off-by:
Chen-Yu Tsai <wens@csie.org> Acked-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
-
Xiaoyao Li authored
commit 98ae70cc upstream. Commit ca83b4a7 ("x86/KVM/VMX: Add find_msr() helper function") introduces the helper function find_msr(), which returns -ENOENT when not find the msr in vmx->msr_autoload.guest/host. Correct checking contion of no more available entry in vmx->msr_autoload. Fixes: ca83b4a7 ("x86/KVM/VMX: Add find_msr() helper function") Cc: stable@vger.kernel.org Signed-off-by:
Xiaoyao Li <xiaoyao.li@linux.intel.com> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
-
Vitaly Kuznetsov authored
commit 6b1971c6 upstream. SDM says MSR_IA32_VMX_PROCBASED_CTLS2 is only available "If (CPUID.01H:ECX.[5] && IA32_VMX_PROCBASED_CTLS[63])". It was found that some old cpus (namely "Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz (family: 0x6, model: 0xf, stepping: 0x6") don't have it. Add the missing check. Reported-by:
Zdenek Kaspar <zkaspar82@gmail.com> Tested-by:
Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by:
Jim Mattson <jmattson@google.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Stefan O'Rear authored
commit e3613bb8 upstream. Previously, invalid PTEs and swap PTEs had the same binary representation, causing errors when attempting to unmap PROT_NONE mappings, including implicit unmap on exit. Typical error: swap_info_get: Bad swap file entry 40000000007a9879 BUG: Bad page map in process a.out pte:3d4c3cc0 pmd:3e521401 Cc: stable@vger.kernel.org Signed-off-by:
Stefan O'Rear <sorear2@gmail.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
Palmer Dabbelt <palmer@sifive.com> Signed-off-by:
-
Bob Tracy authored
commit 842fc0f5 upstream. Cc: stable@vger.kernel.org # v4.18+ Signed-off-by:
Bob Tracy <rct@frus.com> Signed-off-by:
-
Russell King authored
commit 0ce23d6d upstream. hdmi-codec oopses the kernel when it is unbound from a successfully bound audio subsystem, and is then rebound: Unable to handle kernel NULL pointer dereference at virtual address 0000001c pgd = ee3f0000 [0000001c] *pgd=3cc59831 Internal error: Oops: 817 [#1] PREEMPT ARM Modules linked in: ext2 snd_soc_spdif_tx vmeta dove_thermal snd_soc_kirkwood ofpart marvell_cesa m25p80 orion_wdt mtd spi_nor des_generic gpio_ir_recv snd_soc_kirkwood_spdif bmm_dmabuf auth_rpcgss nfsd autofs4 etnaviv thermal_sys hwmon gpu_sched tda9950 CPU: 0 PID: 1005 Comm: bash Not tainted 4.20.0+ #1762 Hardware name: Marvell Dove (Cubox) PC is at hdmi_dai_probe+0x68/0x80 LR is at find_held_lock+0x20/0x94 pc : [<c04c7de0>] lr : [<c0063bf4>] psr: 600f0013 sp : ee15bd28 ip : eebd8b1c fp : c093b488 r10: ee048000 r9 : eebdab18 r8 : ee048600 r7 : 00000001 r6 : 00000000 r5 : 00000000 r4 : ee82c100 r3 : 00000006 r2 : 00000001 r1 : c067e38c r0 : ee82c100 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none[ 297.318599] Control: 10c5387d Table: 2e3f0019 DAC: 00000051 Process bash (pid: 1005, stack limit = 0xee15a248) ... [<c04c7de0>] (hdmi_dai_probe) from [<c04b7060>] (soc_probe_dai.part.9+0x34/0x70) [<c04b7060>] (soc_probe_dai.part.9) from [<c04b81a8>] (snd_soc_instantiate_card+0x734/0xc9c) [<c04b81a8>] (snd_soc_instantiate_card) from [<c04b8b6c>] (snd_soc_add_component+0x29c/0x378) [<c04b8b6c>] (snd_soc_add_component) from [<c04b8c8c>] (snd_soc_register_component+0x44/0x54) [<c04b8c8c>] (snd_soc_register_component) from [<c04c64b4>] (devm_snd_soc_register_component+0x48/0x84) [<c04c64b4>] (devm_snd_soc_register_component) from [<c04c7be8>] (hdmi_codec_probe+0x150/0x260) [<c04c7be8>] (hdmi_codec_probe) from [<c0373124>] (platform_drv_probe+0x48/0x98) This happens because hdmi_dai_probe() attempts to access the HDMI codec private data, but this has not been assigned by hdmi_dai_probe() before it calls devm_snd_soc_register_component(). Move the call to dev_set_drvdata() before devm_snd_soc_register_component() to avoid this oops. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Manuel Reinhardt authored
commit 2bc16b9f upstream. The commit a60945fd ("ALSA: usb-audio: move implicit fb quirks to separate function") introduced an error in the handling of quirks for implicit feedback endpoints. This commit fixes this. If a quirk successfully sets up an implicit feedback endpoint, usb-audio no longer tries to find the implicit fb endpoint itself. Fixes: a60945fd ("ALSA: usb-audio: move implicit fb quirks to separate function") Signed-off-by:
Manuel Reinhardt <manuel.rhdt@gmail.com> Cc: <stable@vger.kernel.org> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Jurica Vukadin authored
commit 4cd3016c upstream. This enables mute LED support and fixes switching jacks when the laptop is docked. Signed-off-by:
Jurica Vukadin <jurica.vukadin@rt-rk.com> Cc: <stable@vger.kernel.org> Signed-off-by:
-
Jiri Olsa authored
commit 81ec3f3c upstream. Vince (and later on Ravi) reported crashes in the BTS code during fuzzing with the following backtrace: general protection fault: 0000 [#1] SMP PTI ... RIP: 0010:perf_prepare_sample+0x8f/0x510 ... Call Trace: <IRQ> ? intel_pmu_drain_bts_buffer+0x194/0x230 intel_pmu_drain_bts_buffer+0x160/0x230 ? tick_nohz_irq_exit+0x31/0x40 ? smp_call_function_single_interrupt+0x48/0xe0 ? call_function_single_interrupt+0xf/0x20 ? call_function_single_interrupt+0xa/0x20 ? x86_schedule_events+0x1a0/0x2f0 ? x86_pmu_commit_txn+0xb4/0x100 ? find_busiest_group+0x47/0x5d0 ? perf_event_set_state.part.42+0x12/0x50 ? perf_mux_hrtimer_restart+0x40/0xb0 intel_pmu_disable_event+0xae/0x100 ? intel_pmu_disable_event+0xae/0x100 x86_pmu_stop+0x7a/0xb0 x86_pmu_del+0x57/0x120 event_sched_out.isra.101+0x83/0x180 group_sched_out.part.103+0x57/0xe0 ctx_sched_out+0x188/0x240 ctx_resched+0xa8/0xd0 __perf_event_enable+0x193/0x1e0 event_function+0x8e/0xc0 remote_function+0x41/0x50 flush_smp_call_function_queue+0x68/0x100 generic_smp_call_function_single_interrupt+0x13/0x30 smp_call_function_single_interrupt+0x3e/0xe0 call_function_single_interrupt+0xf/0x20 </IRQ> The reason is that while event init code does several checks for BTS events and prevents several unwanted config bits for BTS event (like precise_ip), the PERF_EVENT_IOC_PERIOD allows to create BTS event without those checks being done. Following sequence will cause the crash: If we create an 'almost' BTS event with precise_ip and callchains, and it into a BTS event it will crash the perf_prepare_sample() function because precise_ip events are expected to come in with callchain data initialized, but that's not the case for intel_pmu_drain_bts_buffer() caller. Adding a check_period callback to be called before the period is changed via PERF_EVENT_IOC_PERIOD. It will deny the change if the event would become BTS. Plus adding also the limit_period check as well. Reported-by:
Vince Weaver <vincent.weaver@maine.edu> Signed-off-by:
Jiri Olsa <jolsa@kernel.org> Acked-by:
Peter Zijlstra <peterz@infradead.org> Cc: <stable@vger.kernel.org> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Arnaldo Carvalho de Melo <acme@redhat.com> Cc: Jiri Olsa <jolsa@redhat.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Cc: Ravi Bangoria <ravi.bangoria@linux.ibm.com> Cc: Stephane Eranian <eranian@google.com> Cc: Thomas Gleixner <tglx@linutronix.de> Link: http://lkml.kernel.org/r/20190204123532.GA4794@kravaSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Ingo Molnar authored
commit 528871b4 upstream. The following commit: 9dff0aa9 ("perf/core: Don't WARN() for impossible ring-buffer sizes") results in perf recording failures with larger mmap areas: root@skl:/tmp# perf record -g -a failed to mmap with 12 (Cannot allocate memory) The root cause is that the following condition is buggy: if (order_base_2(size) >= MAX_ORDER) goto fail; The problem is that @size is in bytes and MAX_ORDER is in pages, so the right test is: if (order_base_2(size) >= PAGE_SHIFT+MAX_ORDER) goto fail; Fix it. Reported-by:
"Jin, Yao" <yao.jin@linux.intel.com> Bisected-by:
Borislav Petkov <bp@alien8.de> Analyzed-by:
-
Tony Lindgren authored
commit d0243693 upstream. Commit 83a86fbb ("irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE") started warning about incorrect dts usage for irqs. ARM GIC only supports active-high interrupts for SPI (Shared Peripheral Interrupts), and the Palmas PMIC by default is active-low. Palmas PMIC allows changing the interrupt polarity using register PALMAS_POLARITY_CTRL_INT_POLARITY, but configuring sys_nirq1 with a pull-down and setting PALMAS_POLARITY_CTRL_INT_POLARITY made the Palmas RTC interrupts stop working. This can be easily tested with kernel tools rtctest.c. Turns out the SoC inverts the sys_nirq pins for GIC as they do not go through a peripheral device but go directly to the MPUSS wakeupgen. I've verified this by muxing the interrupt line temporarily to gpio_wk16 instead of sys_nirq1. with a gpio, the interrupt works fine both active-low and active-high with the SoC internal pull configured and palmas polarity configured. But as sys_nirq1, the interrupt only works when configured ACTIVE_LOW for palmas, and ACTIVE_HIGH for GIC. Note that there was a similar issue earlier with tegra114 and palmas interrupt polarity that got fixed by commit df545d1c ("mfd: palmas: Provide irq flags through DT/platform data"). However, the difference between omap5 and tegra114 is that tegra inverts the palmas interrupt twice, once when entering tegra PMC, and again when exiting tegra PMC to GIC. Let's fix the issue by adding a custom wakeupgen_irq_set_type() for wakeupgen and invert any interrupts with wrong polarity. Let's also warn about any non-sysnirq pins using wrong polarity. Note that we also need to update the dts for the level as IRQ_TYPE_NONE never has irq_set_type() called, and let's add some comments and use proper pin nameing to avoid more confusion later on. Cc: Belisko Marek <marek.belisko@gmail.com> Cc: Dmitry Lifshitz <lifshitz@compulab.co.il> Cc: "Dr. H. Nikolaus Schaller" <hns@goldelico.com> Cc: Jon Hunter <jonathanh@nvidia.com> Cc: Keerthy <j-keerthy@ti.com> Cc: Laxman Dewangan <ldewangan@nvidia.com> Cc: Nishanth Menon <nm@ti.com> Cc: Peter Ujfalusi <peter.ujfalusi@ti.com> Cc: Richard Woodruff <r-woodruff2@ti.com> Cc: Santosh Shilimkar <ssantosh@kernel.org> Cc: Tero Kristo <t-kristo@ti.com> Cc: Thierry Reding <treding@nvidia.com> Cc: stable@vger.kernel.org # v4.17+ Reported-by:
Belisko Marek <marek.belisko@gmail.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Mauro Ciancio authored
commit 7ad222b3 upstream. This adds ELAN0617 to the ACPI table to support Elan touchpad found in Lenovo V330-15ISK. Signed-off-by:
Mauro Ciancio <mauro@acadeu.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Dmitry Torokhov authored
commit f420c54e upstream. This reverts commit 7db54c89 as it breaks Acer Aspire V-371 and other devices. According to Elan: "Acer Aspire F5-573G is MS Precision touchpad which should use hid multitouch driver. ELAN0501 should not be added in elan_i2c." Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=202503 Cc: stable@vger.kernel.org Signed-off-by:
-
Anson Huang authored
commit 1a5287a3 upstream. During noirq suspend/resume phase, GPIO irq could arrive and its registers like IMR will be changed by irq handle process, to make the GPIO registers exactly when it is powered ON after resume, move the GPIO noirq suspend/resume callback to syscore suspend/resume phase, local irq is disabled at this phase so GPIO registers are atomic. Fixes: c19fdaee ("gpio: mxc: add power management support") Signed-off-by:
Anson Huang <Anson.Huang@nxp.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Martin Hundebøll <martin@geanix.com> Cc: <stable@vger.kernel.org> # 4.19.x+ Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Pavel Shilovsky authored
[ Upstream commit 0fd1d37b ] If we don't receive a response we can't assume that the server granted one credit. Assume zero credits in such cases. Signed-off-by:
Pavel Shilovsky <pshilov@microsoft.com> Reviewed-by:
Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Signed-off-by:
-
David Rientjes authored
[ Upstream commit 3f14a89d ] By code inspection, it was found that multiple calls to KVM_SEV_INIT could deplete asid bits and overwrite kvm_sev_info's regions_list. Multiple calls to KVM_SVM_INIT is not likely to occur with QEMU, but this should likely be fixed anyway. This code is serialized by kvm->lock. Fixes: 1654efcb ("KVM: SVM: Add KVM_SEV_INIT command") Reported-by:
Cfir Cohen <cfir@google.com> Signed-off-by:
David Rientjes <rientjes@google.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Ross Lagerwall authored
[ Upstream commit 92a8109e ] The code tries to allocate a contiguous buffer with a size supplied by the server (maxBuf). This could fail if memory is fragmented since it results in high order allocations for commonly used server implementations. It is also wasteful since there are probably few locks in the usual case. Limit the buffer to be no larger than a page to avoid memory allocation failures due to fragmentation. Signed-off-by:
Ross Lagerwall <ross.lagerwall@citrix.com> Signed-off-by:
-
Ilia Mirkin authored
[ Upstream commit a5176a4c ] Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108980Signed-off-by:
Ilia Mirkin <imirkin@alum.mit.edu> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
Takashi Iwai authored
[ Upstream commit 11878006 ] When a fan is controlled via linear fallback without cstate, we shouldn't stop polling. Otherwise it won't be adjusted again and keeps running at an initial crazy pace. Fixes: 800efb4c ("drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios") Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1103356 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107447Reported-by:
Thomas Blume <thomas.blume@suse.com> Signed-off-by:
Martin Peres <martin.peres@free.fr> Signed-off-by:
-
Nicholas Mc Guire authored
[ Upstream commit df209c43 ] devm_kzalloc(), devm_kstrdup() and devm_kasprintf() all can fail internal allocation and return NULL. Using any of the assigned objects without checking is not safe. As this is early in the boot phase and these allocations really should not fail, any failure here is probably an indication of a more serious issue so it makes little sense to try and rollback the previous allocated resources or try to continue; but rather the probe function is simply exited with -ENOMEM. Signed-off-by:
Nicholas Mc Guire <hofrat@osadl.org> Fixes: 684284b6 ("ARM: integrator: add MMCI device to IM-PD1") Signed-off-by:
-
Linus Walleij authored
[ Upstream commit b5f03484 ] These two lines are active high, not active low. The bug was found when we changed the kernel to respect the polarity defined in the device tree. Fixes: 1b90e06b ("ARM: kirkwood: Use devicetree to define DNS-32[05] fan") Cc: Jamie Lentin <jm@lentin.co.uk> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Gregory Clement <gregory.clement@bootlin.com> Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com> Cc: Julien D'Ascenzio <jdascenzio@posteo.net> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Tested-by:
Jamie Lentin <jm@lentin.co.uk> Reported-by:
Julien D'Ascenzio <jdascenzio@posteo.net> Tested-by:
Gregory CLEMENT <gregory.clement@bootlin.com> Signed-off-by:
-
Peter Ujfalusi authored
[ Upstream commit c25748ac ] To avoid the following error: asoc-simple-card sound: ASoC: Failed to create card debugfs directory Which is because the card name contains '/' character, which can not be used in file or directory names. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
Sekhar Nori <nsekhar@ti.com> Signed-off-by:
-
Peter Ujfalusi authored
[ Upstream commit bd540ebe ] Add the board level fixed regulators for 3.3V and 1.8V which is used to power - among other things - the tlv320aic3106 codec. Apart from removing the following warning during boot: tlv320aic3x-codec 0-0018: Invalid supply voltage(s) AVDD: -22, DVDD: -22 With the correct voltages the driver can select correct OCMV value to reduce pop noise. Signed-off-by:
-
Peter Ujfalusi authored
[ Upstream commit 7fca69d4 ] To avoid the following error: asoc-simple-card sound: ASoC: Failed to create card debugfs directory Which is because the card name contains '/' character, which can not be used in file or directory names. Signed-off-by:
-
Peter Ujfalusi authored
[ Upstream commit 706edaa8 ] Add the board level fixed regulators for 3.3V and 1.8V which is used to power - among other things - the tlv320aic3106 codec. Apart from removing the following warning during boot: tlv320aic3x-codec 0-0018: Too high supply voltage(s) AVDD: 5000000, DVDD: 5000000 With the correct voltages the driver can select correct OCMV value to reduce pop noise. Signed-off-by:
-
Jim Qu authored
[ Upstream commit 0c6c8125 ] effect asics: VEGA10 and VEGA12 Signed-off-by:
Jim Qu <Jim.Qu@amd.com> Acked-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
