There are four link statuses of a bonding slave, the procfs
code shows a wrong status when using downdelay/updelay:

	(slave->link == BOND_LINK_UP) ?  "up" : "down"

It doesn't respect the rest two statuses. This patch fixes it.

Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As seen on smsc75xx, driver_info->description being longer than 32
characters messes up 'ethtool -i' output.
Signed-off-by: Phil Sutter <phil.sutter@viprinet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Increasing the hardware statistics structure to accomodate statistics for skyhawk.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Modify IOCTL error message to print subsystem also.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The maximum size of packet that can be handled by controller including ethernet
header is 65535. Reducing gso_max_size accordingly.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes a potential hole when configuring the cycle counter used to
generate the nanosecond time clock. This clock is based off of the SYSTIME
registers along with the TIMINCA registers. The TIMINCA register determines
the increment to be added to the SYSTIME registers every DMA clock tick. This
register needs to be reconfigured whenever the link-speed changes. However,
the value calculated stays the same when link is down and when link is up.
Misconfiguration can occur if the link status changes due to a reset, which
causes the TIMINCA register to be reset. This reset puts the device in an
unstable state where the SYSTIME registers stop incrementing and the PTP
protocol does not function.

The solution is to double check the TIMINCA value and always reset the value
if the register is zero. This prevents a misconfiguration bug that halts the
PHC.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When I2C is not responding it's usually due to a previous
unexpected reset during I2C operation. We release it by
powering down and up the SFP+ module.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 2a0c451a.

It causes crashes, because now ip6_null_entry is used before
it is initialized.
Signed-off-by: David S. Miller <davem@davemloft.net>

/proc/net/ipv6_route reflects the contents of fib_table_hash. The proc
handler is installed in ip6_route_net_init() whereas fib_table_hash is
allocated in fib6_net_init() _after_ the proc handler has been installed.

This opens up a short time frame to access fib_table_hash with its pants
down.

fib6_init() as a whole can't be moved to an earlier position as it also
registers the rtnetlink message handlers which should be registered at
the end. Therefore split it into fib6_init() which is run early and
fib6_init_late() to register the rtnetlink message handlers.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The adapter->npars[] array has QLCNIC_MAX_PCI_FUNC elements.  We
allocate it that way a few lines earlier in the function.  So this test
is off by one.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Orphaning skb in dev_hard_start_xmit() makes bonding behavior
unfriendly for applications sending big UDP bursts : Once packets
pass the bonding device and come to real device, they might hit a full
qdisc and be dropped. Without orphaning, the sender is automatically
throttled because sk->sk_wmemalloc reaches sk->sk_sndbuf (assuming
sk_sndbuf is not too big)

We could try to defer the orphaning adding another test in
dev_hard_start_xmit(), but all this seems of little gain,
now that BQL tends to make packets more likely to be parked
in Qdisc queues instead of NIC TX ring, in cases where performance
matters.

Reverts commits :
fc6055a5 net: Introduce skb_orphan_try()
87fd308c net: skb_tx_hash() fix relative to skb_orphan_try()
and removes SKBTX_DRV_NEEDS_SK_REF flag
Reported-and-bisected-by: Jean-Michel Hautbois <jhautbois@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a off by one error in the minimal number of BD in
bnx2x_start_xmit() and bnx2x_tx_int() before stopping/resuming tx queue.

A full size GSO packet, with data included in skb->head really needs
(MAX_SKB_FRAGS + 4) BDs, because of bnx2x_tx_split()

This error triggers if BQL is disabled and heavy TCP transmit traffic
occurs.

bnx2x_tx_split() definitely can be called, remove a wrong comment.
Reported-by: Tomas Hruby <thruby@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

(CAN_CTRLMODE_LISTENONLY & CAN_CTRLMODE_LOOPBACK) is (0x02 & 0x01) which
is zero so the condition is never true.  The intent here was to test
that both flags were set.

Cc: <stable@kernel.org> # 2.6.39+
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull kvm fix from Marcelo Tosatti:
 "Fix a spurious warning on CPU offline path"

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  x86: kvmclock: remove check_and_clear_guest_paused warning

Merge tag 'pinctrl-fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pinctrl fixes from Linus Walleij:
 - section markup fixes
 - clk_prepare() fix to conform to the clk API
 - memory leaks
 - incorrect debug messages
 - bad errorpaths
 - typos

* tag 'pinctrl-fixes-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: pinctrl-mxs: set platform driver data to NULL at errpath and at unregister
  pinctrl: pinctrl-mxs: Take care of frees if the kzalloc fails
  pinctrl: pinctrl-imx: fix incorrect debug message of maps
  pinctrl: pinctrl-imx: free if of_get_parent fails to get the parent node
  pinctrl: pinctrl-imx: free allocated pinctrl_map structure only once and use kernel facilities for IMX_PMX_DUMP
  pinctrl: nomadik: fix up typo
  pinctrl: nomadik: add clk_prepare() call
  pinctrl: fix a minor harmless typo
  pinctrl: sirf: mark of_device_id match table as __devinitconst

Pull sound fixes from Takashi Iwai:

 - Fix a regression of USB-audio PCM assignment since 3.4
 - A few VGA-switcheroo-related fixes for proper HDMI audio enablement
 - Fixed the missing initializations of HD-audio verbs, which may have
   resulted in various breakage
 - Some driver-specific ASoC updates
 - A few fixes for the dynamic PCM code
 - The addition of pinctrl support for the i.MX audmux which didn't make
   it into -rc1 due to cross tree dependency issues
 - A few minor fixes in compress API codes

* tag 'sound-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Don't forget to call init verbs added by fixup list
  ALSA: HDA: Pin fixup for Zotac Z68 motherboard
  ALSA: compress_core: cleanup pointers on stop
  ALSA: compress_core: don't wake up on pause
  ALSA: hda - Fix detection of Creative SoundCore3D controllers
  vga_switcheroo: Enable/disable audio clients at the right time
  ALSA: hda - HDMI Audio init all connectors when VGA-switcheroo is off
  vga_switcheroo: Fix error without CONFIG_VGA_SWITCHEROO
  ALSA: hda - Fix uninitialized HDMI controllers with VGA-switcheroo
  vga_switcheroo: Add a helper function to get the client state
  ALSA: usb-audio: Fix substream assignments
  ASoC: tegra: add MODULE_DEVICE_TABLE to tegra30_ahub
  ASoC: wm2000: Always use a 4s timeout for the firmware
  ASoC: dapm: Fix input list to use source widgets
  ASoC: dpcm: Fix dpcm_get_be() to check that DAI is BE
  ASoC: wm8994: Apply volume updates with clocks enabled
  ASoC: wm8994: Ensure all AIFnCLK events are run from the _late variants
  ASoC: imx-audmux: add pinctrl support
  ASoC: dapm: Fix connected widget capture path query.

Pull networking fixes from David S. Miller:

This has the fix for the wireless issues I ran into the other week as
well as:

 1) Fix CAN c_can driver transmit handling resulting in BUG check
    triggers, from AnilKumar Ch.

 2) Fix packet drop monitor sleeping in atomic context, from Eric
    Dumazet.

 3) Fix mv643xx_eth driver build regression, from Andrew Lunn.

 4) Inetpeer freeing needs an RCU grace period in order to avoid races
    during tree invalidation.  From Eric Dumazet.

 5) Fix endianness bugs in xt_HMARK netfilter module, from Hans
    Schillstrom.

 6) Add proper module refcounting to l2tp_eth to avoid crash on module
    unload, from Eric Dumazet.

 7) Fix truncation of neighbour entry dumps due to logic errors in
    neigh_dump_info() and friends, from Eric Dumazet.

 8) The conversion of fib6_age() to dst_neigh_lookup() accidently
    reversed the logic of a flags test, fix from Thomas Graf.

 9) Fix checksum configuration in newer sky2 chips, from Stephen
    Hemminger.

10) Revert BQL support in NIU driver, doesn't work.

11) l2tp_ip_sendmsg() illegally uses a route without a proper reference.
    From Eric Dumazet.

12) be2net driver references an SKB after it's potentially been freed,
    also from Eric Dumazet.

13) Fix RCU stalls in dummy net driver init.  Also from Eric Dumazet.

14) lpc_eth has several bugs in it's transmit engine leading to packet
    leaks and improper queue wakes, from Eric Dumazet.

15) Apply short DMA workaround to more tg3 chips, from Matt Carlson.

16) Add tilegx network driver.

17) Bonding queue mapping for a packet can get corrupted, fix from Eric
    Dumazet.

18) Fix bug in netpoll_send_udp() SKB management that can leave garbage
    in the payload in certain situations.  From Eric Dumazet.

19) bnx2x driver interprets chip RX checksum offload incorrectly in
    encapsulation situations.  Fix from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (75 commits)
  bnx2x: fix checksum validation
  netpoll: fix netpoll_send_udp() bugs
  bonding: Fix corrupted queue_mapping
  bonding:record primary when modify it via sysfs
  tilegx network driver: initial support
  tg3: Apply short DMA frag workaround to 5906
  net: stmmac: Fix clock en-/disable calls
  lpc_eth: fix tx completion
  lpc_eth: add missing ndo_change_mtu()
  dummy: fix rcu_sched self-detected stalls
  net: Reorder initialization in ip_route_output to fix gcc warning
  virtio-net: fix a race on 32bit arches
  r8169: avoid NAPI scheduling delay.
  net: Make linux/tcp.h C++ friendly (trivial)
  netdev: fix drivers/net/phy/ kernel-doc warnings
  net/core: fix kernel-doc warnings
  be2net: fix a race in be_xmit()
  l2tp: fix a race in l2tp_ip_sendmsg()
  mac80211: add back channel change flag
  NFC: Fix possible NULL ptr deref when getting the name of a socket
  ...

bnx2x driver incorrectly sets ip_summed to CHECKSUM_UNNECESSARY on
encapsulated segments. TCP stack happily accepts frames with bad
checksums, if they are inside a GRE or IPIP encapsulation.

Our understanding is that if no IP or L4 csum validation was done by the
hardware, we should leave ip_summed as is (CHECKSUM_NONE), since
hardware doesn't provide CHECKSUM_COMPLETE support in its cqe.

Then, if IP/L4 checksumming was done by the hardware, set
CHECKSUM_UNNECESSARY if no error was flagged.

Patch based on findings and analysis from Robert Evans
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Yaniv Rosner <yanivr@broadcom.com>
Cc: Merav Sicron <meravs@broadcom.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Robert Evans <evansr@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bogdan Hamciuc diagnosed and fixed following bug in netpoll_send_udp() :

"skb->len += len;" instead of "skb_put(skb, len);"

Meaning that _if_ a network driver needs to call skb_realloc_headroom(),
only packet headers would be copied, leaving garbage in the payload.

However the skb_realloc_headroom() must be avoided as much as possible
since it requires memory and netpoll tries hard to work even if memory
is exhausted (using a pool of preallocated skbs)

It appears netpoll_send_udp() reserved 16 bytes for the ethernet header,
which happens to work for typicall drivers but not all.

Right thing is to use LL_RESERVED_SPACE(dev)
(And also add dev->needed_tailroom of tailroom)

This patch combines both fixes.

Many thanks to Bogdan for raising this issue.
Reported-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh:
  sh: Kill off additional asm-generic wrappers.
  sh: Setup CROSS_COMPILE at the top
  sh: Fix up link time defsym warnings.
  sh: use the new generic strnlen_user() function
  sh: switch to generic strncpy_from_user().
  sh: Kill off last dead UBC header
  serial: sh-sci: Make probe fail for ports that exceed the maximum count
  serial: sh-sci: Fix probe error paths
  clocksource: sh_tmu: Use clockevents_config_and_register().
  clocksource: sh_tmu: Convert timer lock to raw spinlock.
  clocksource: sh_mtu2: Convert timer lock to raw spinlock.
  clocksource: sh_cmt: Convert timer lock to raw spinlock.
  bug.h: need linux/kernel.h for TAINT_WARN.
  sh: convert to kbuild asm-generic support.
  sh64: Fix up fallout from generic init_task conversion.
  sh: arch/sh/kernel/process.c needs asm/fpu.h for unlazy_fpu().

Pull led fixes from Bryan Wu.

* 'fixes-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/linux-leds:
  leds: Make LEDS_ASIC3 and LEDS_RENESAS_TPU depend on LEDS_CLASS=y
  leds: fixed a coding style issue.
  leds: don't disable blinking when writing the same value to delay_on or delay_off

Pull m68k update from Geert Uytterhoeven.

This makes m68k use the generic library functions for the user-space
strn[cpy|len] functions.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: Use generic strncpy_from_user(), strlen_user(), and strnlen_user()

Pull omapdss build problem fix from Tomi Valkeinen:
 "Small fixes for omapdss driver.  Most importantly, fixes a build
  problem when debugfs or omapdss debug support is turned off, and fixes
  a suspend related crash."

This has apparently been annoying rmk for a while..

* tag 'omapdss-for-3.5-rc2' of git://gitorious.org/linux-omap-dss2/linux:
  OMAPDSS: fix registration of DPI and SDI devices
  OMAPDSS: DSI: Fix bug when calculating LP command interleaving parameters
  OMAPDSS: fix bogus WARN_ON in dss_runtime_put()
  OMAPDSS: Taal: fix compilation warning
  OMAPDSS: fix build when DEBUG_FS or DSS_DEBUG_SUPPORT disabled

During the split to the auto-parser helper functions, the actual call
of init verbs was lost.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43366Signed-off-by: Takashi Iwai <tiwai@suse.de>

Merge branches 'sh/urgent', 'sh/core', 'sh/clockevents', 'sh/asm-generic' and 'sh/trivial' into sh-fixes-for-linus

A few wrappers were overlooked in the initial conversion, take care of
them now.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

CROSS_COMPILE must be setup before using e.g. cc-option (and a few other
as-*, cc-*, ld-* macros), else they will check against the wrong compiler
when cross-compiling, and may invoke the cross compiler with wrong or
suboptimal compiler options.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: linux-sh@vger.kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

sh-linux-gnu-ld:--defsym 'jiffies=jiffies_64': ignoring invalid character `'' in expression

For some reason ld has recently started complaining about the quotes, so just
get rid of them, we don't need them for anything anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This discards both the _32 and _64 versions in favour of the consolidated
generic one.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

This kills off the special sh32/64 versions and adopts the generic
version. It should be possible to optimize this for SH-4A unaligned
loads, but this is a corner case that can be supported incrementally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Commit 7025bec9 ("sh: Kill off dead UBC
headers.") skipped arch/sh/include/cpu-sh2a/cpu/ubc.h. Since nothing is
using that header either, kill it off too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

The driver supports a maximum number of ports configurable at compile
time. Make sure the probe() method fails when registering a port that
exceeds the maximum instead of returning success without registering the
port.

This fixes a crash at system suspend time, when the driver tried to
suspend a non-registered port using the UART core.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

When probing fails, the driver must not try to cleanup resources that
have not been initialized. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

In the transmit path of the bonding driver, skb->cb is used to
stash the skb->queue_mapping so that the bonding device can set its
own queue mapping.  This value becomes corrupted since the skb->cb is
also used in __dev_xmit_skb.

When transmitting through bonding driver, bond_select_queue is
called from dev_queue_xmit.  In bond_select_queue the original
skb->queue_mapping is copied into skb->cb (via bond_queue_mapping)
and skb->queue_mapping is overwritten with the bond driver queue.

Subsequently in dev_queue_xmit, __dev_xmit_skb is called which writes
the packet length into skb->cb, thereby overwriting the stashed
queue mappping.  In bond_dev_queue_xmit (called from hard_start_xmit),
the queue mapping for the skb is set to the stashed value which is now
the skb length and hence is an invalid queue for the slave device.

If we want to save skb->queue_mapping into skb->cb[], best place is to
add a field in struct qdisc_skb_cb, to make sure it wont conflict with
other layers (eg : Qdiscc, Infiniband...)

This patchs also makes sure (struct qdisc_skb_cb)->data is aligned on 8
bytes :

netem qdisc for example assumes it can store an u64 in it, without
misalignment penalty.

Note : we only have 20 bytes left in (struct qdisc_skb_cb)->data[].
The largest user is CHOKe and it fills it.

Based on a previous patch from Tom Herbert.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Tom Herbert <therbert@google.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Cc: Roland Dreier <roland@kernel.org>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If we modify primary via sysfs and it is not a valid slave,
we should record it for future use, and this behavior is the same with
bond_check_params().
Signed-off-by: Weiping Pan <wpan@redhat.com>
Acked-by: Nicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pin 0x1b was connected to the front panel connector, which according to
the HDA standard should contain a mic and a headphone. In this case,
the headphone was listed as "line out" by BIOS.

Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/993162Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

as the start can be called after stop again, we need to reset state
Signed-off-by: Namarta Kohli <namartax.kohli@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

during pause the core should maintain the status-quo on the device and pointers
and not wake up. If app needs it should call DROP explcitly.
Signed-off-by: Namarta Kohli <namartax.kohli@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>