The range of addresses between 224.0.0.0 and 224.0.0.255 inclusive, is
reserved for the use of routing protocols and other low-level topology
discovery or maintenance protocols, such as gateway discovery and
group membership reporting.  Multicast routers should not forward any
multicast datagram with destination addresses in this range,
regardless of its TTL.

Currently, IGMP reports are generated for this reserved range of
addresses even though a router will ignore this information since it
has no purpose.  However, the presence of reserved group addresses in
an IGMP membership report uses up network bandwidth and can also
obscure addresses of interest when inspecting membership reports using
packet inspection or debug messages.

Although the RFCs for the various version of IGMP (e.g.RFC 3376 for
v3) do not specify that the reserved addresses be excluded from
membership reports, it should do no harm in doing so.  In particular
there should be no adverse effect in any IGMP snooping functionality
since 224.0.0.x is specifically excluded as per RFC 4541 (IGMP and MLD
Snooping Switches Considerations) section 2.1.2. Data Forwarding
Rules:

    2) Packets with a destination IP (DIP) address in the 224.0.0.X
       range which are not IGMP must be forwarded on all ports.

IGMP reports for local multicast groups can now be optionally
inhibited by means of a system control variable (by setting the value
to zero) e.g.:
    echo 0 > /proc/sys/net/ipv4/igmp_link_local_mcast_reports

To retain backwards compatibility the previous behaviour is retained
by default on system boot or reverted by setting the value back to
non-zero e.g.:
    echo 1 >  /proc/sys/net/ipv4/igmp_link_local_mcast_reports
Signed-off-by: Philip Downey <pdowney@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The multicast hardware counter on 8168/8111 chips is only 32 bit while the
statistics in struct rtnl_link_stats64 are 64 bit.  Given that statistics
are requested on an irregular basis, an overflow of the hardware counter
can go unnoticed.  To count even very large numbers of multicast packets
reliably, add a software counter and remove previously applied code to
fill the multicast field requested by @rtl8169_get_stats64 with the values
read from the rx_multicast hardware counter.
Signed-off-by: Corinna Vinschen <vinschen@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull powerpc fixes from Michael Ellerman:
 "Fix MSI/MSI-X on pseries from Guilherme"

* tag 'powerpc-4.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/PCI: Disable MSI/MSI-X interrupts at PCI probe time in OF case
  PCI: Make pci_msi_setup_pci_dev() non-static for use by arch code

Pull networking fixes from David Miller:
 "Some straggler bug fixes here:

   1) Netlink_sendmsg() doesn't check iterator type properly in mmap
      case, from Ken-ichirou MATSUZAWA.

   2) Don't sleep in atomic context in bcmgenet driver, from Florian
      Fainelli.

   3) The pfkey_broadcast() code patch can't actually ever use anything
      other than GFP_ATOMIC.  And the cases that right now pass
      GFP_KERNEL or similar will currently trigger an RCU splat.  Just
      use GFP_ATOMIC unconditionally.  From David Ahern.

   4) Fix FD bit timings handling in pcan_usb driver, from Marc
      Kleine-Budde.

   5) Cache dst leaked in ip6_gre tunnel removal, fix from Huaibin Wang.

   6) Traversal into drivers/net/ethernet/renesas should be triggered by
      CONFIG_NET_VENDOR_RENESAS, not a particular driver's config
      option.  From Kazuya Mizuguchi.

   7) Fix regression in handling of igmp_join errors in vxlan, from
      Marcelo Ricardo Leitner.

   8) Make phy_{read,write}_mmd_indirect() properly take the mdio_lock
      mutex when programming the registers.  From Russell King.

   9) Fix non-forced handling in u32_destroy(), from WANG Cong.

  10) Test the EVENT_NO_RUNTIME_PM flag before it is cleared in
      usbnet_stop(), from Eugene Shatokhin.

  11) In sfc driver, don't fetch statistics firmware isn't capable of,
      from Bert Kenward.

  12) Verify ASCONF address parameter location in SCTP, from Xin Long"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  sctp: donot reset the overall_error_count in SHUTDOWN_RECEIVE state
  sctp: asconf's process should verify address parameter is in the beginning
  sfc: only use vadaptor stats if firmware is capable
  net: phy: fixed: propagate fixed link values to struct
  usbnet: Get EVENT_NO_RUNTIME_PM bit before it is cleared
  drivers: net: xgene: fix: Oops in linkwatch_fire_event
  cls_u32: complete the check for non-forced case in u32_destroy()
  net: fec: use reinit_completion() in mdio accessor functions
  net: phy: add locking to phy_read_mmd_indirect()/phy_write_mmd_indirect()
  vxlan: re-ignore EADDRINUSE from igmp_join
  net: compile renesas directory if NET_VENDOR_RENESAS is configured
  ip6_gre: release cached dst on tunnel removal
  phylib: Make PHYs children of their MDIO bus, not the bus' parent.
  can: pcan_usb: don't provide CAN FD bittimings by non-FD adapters
  net: Fix RCU splat in af_key
  net: bcmgenet: fix uncleaned dma flags
  net: bcmgenet: Avoid sleeping in bcmgenet_timeout
  netlink: mmap: fix tx type check

Pull nvdimm fixlet from Dan Williams:
 "This is a libnvdimm ABI fixup.

  I pushed back on this change quite hard given the late date, that it
  appears to be purely cosmetic, sysfs is not necessarily meant to be a
  user friendly UI, and the kernel interprets the reversed polarity of
  the ACPI_NFIT_MEM_ARMED flag correctly.  When this flag is set, the
  energy source of an NVDIMM is not armed and any new writes to the DIMM
  may not be preserved.

  However, Bob Moore warned me that it is important to get these things
  named correctly wherever they appear otherwise we run the risk of a
  less than cautious firmware engineer implementing the polarity the
  wrong way.  Once a mistake like that escapes into production platforms
  the flag becomes useless and we need to move to a new bit position.

  Bob has agreed to take a change through ACPICA to rename
  ACPI_NFIT_MEM_ARMED to ACPI_NFIT_MEM_NOT_ARMED, and the patch below
  from Toshi brings the sysfs representation of these flags in line with
  their respective polarities.

  Please pull for 4.2 as this is the first kernel to expose the ACPI
  NFIT sysfs representation, and this is likely a kernel that firmware
  developers will be using for checking out their NVDIMM enabling"

* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nfit: Clarify memory device state flags strings

Phil Sutter says:

====================
fixup IFF_NO_QUEUE conversion

This series serves two purposes:

On one hand it fixes a quite embarrassing bug around the warning I added for
drivers still setting tx_queue_len = 0 to achieve noqueue operation. It turned
out to be quite useless as due to using alloc_netdev(), many in-kernel drivers
fell into the trap by accident, as well. Instead this place serves pretty well
as a sanitizing point to set IFF_NO_QUEUE for drivers not initializing
tx_queue_len, which in turn allows to drop all special treatment of the latter
being zero since that can not happen anymore without IFF_NO_QUEUE being set.

On the other hand, it provides a better solution for Eric Dumazet's concern
regarding how to assign noqueue to an interface which does not default to it
already. In order to make this possible, noqueue is being registered so users
can 'tc qd add dev eth0 root noqueue'. In addition, it resolves the ugly
situation of 'tc qd show' not showing noqueue. Finally, the former changes
allow for some code cleanup.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that noqueue qdisc can be attached just like any other qdisc, no
special treatment is necessary anymore when attaching it as default
qdisc.

This change has the added benefit that 'tc qdisc show' prints noqueue
instead of nothing for devices defaulting to noqueue.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

This way users can attach noqueue just like any other qdisc using tc
without having to mess with tx_queue_len first.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since alloc_netdev_mqs() sets IFF_NO_QUEUE for drivers not initializing
tx_queue_len, it is safe to assume that if tx_queue_len is zero,
dev->priv flags always contains IFF_NO_QUEUE.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Printing a warning in alloc_netdev_mqs() if tx_queue_len is zero and
IFF_NO_QUEUE not set is not appropriate since drivers may use one of the
alloc_netdev* macros instead of alloc_etherdev*, thereby not
intentionally leaving tx_queue_len uninitialized. Instead check here if
tx_queue_len is zero and set IFF_NO_QUEUE, so the value of tx_queue_len
can be ignored in net/sched_generic.c.

Fixes: 906470c1 ("net: warn if drivers set tx_queue_len = 0")
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

The symbol '__sk_reclaim' is not present in the current tree. Apparently
'__sk_reclaim' was meant to be '__sk_mem_reclaim', so fix it with the
right symbol name for the kernel doc.
Signed-off-by: Jean Sacren <sakiwit@gmail.com>
Cc: Hideo Aoki <haoki@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit f8d96052 ("sctp: Enforce retransmission limit during shutdown")
fixed a problem with excessive retransmissions in the SHUTDOWN_PENDING by not
resetting the association overall_error_count.  This allowed the association
to better enforce assoc.max_retrans limit.

However, the same issue still exists when the association is in SHUTDOWN_RECEIVED
state.  In this state, HB-ACKs will continue to reset the overall_error_count
for the association would extend the lifetime of association unnecessarily.

This patch solves this by resetting the overall_error_count whenever the current
state is small then SCTP_STATE_SHUTDOWN_PENDING.  As a small side-effect, we
end up also handling SCTP_STATE_SHUTDOWN_ACK_SENT and SCTP_STATE_SHUTDOWN_SENT
states, but they are not really impacted because we disable Heartbeats in those
states.

Fixes: Commit f8d96052 ("sctp: Enforce retransmission limit during shutdown")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The uninitialized value name in mlx4_en_activate_cq was used in order
to print an error message. Fixing it by replacing it with cq->vector.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We currently manage IRQs in pool_bm which is a bit field
of MAX_MSIX bits. Thus, allocating more than MAX_MSIX
interrupts can't be managed in pool_bm.
Fixing this by capping number of requested MSIXs to
MAX_MSIX.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Carol L Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While looking into fixing the local entries scalability issue I noticed
that the structure is badly arranged because vlan_id would fall in a
second cache line while keeping rcu which is used only when deleting
in the first, so re-arrange the structure and push rcu to the end so we
can get 16 bytes which can be used for other fields (by pushing rcu
fully in the second 64 byte chunk). With this change all the core
necessary information when doing fdb lookups will be available in a
single cache line.

pahole before (note vlan_id):
struct net_bridge_fdb_entry {
	struct hlist_node          hlist;                /*     0    16 */
	struct net_bridge_port *   dst;                  /*    16     8 */
	struct callback_head       rcu;                  /*    24    16 */
	long unsigned int          updated;              /*    40     8 */
	long unsigned int          used;                 /*    48     8 */
	mac_addr                   addr;                 /*    56     6 */
	unsigned char              is_local:1;           /*    62: 7  1 */
	unsigned char              is_static:1;          /*    62: 6  1 */
	unsigned char              added_by_user:1;      /*    62: 5  1 */
	unsigned char              added_by_external_learn:1; /*    62: 4  1 */

	/* XXX 4 bits hole, try to pack */
	/* XXX 1 byte hole, try to pack */

	/* --- cacheline 1 boundary (64 bytes) --- */
	__u16                      vlan_id;              /*    64     2 */

	/* size: 72, cachelines: 2, members: 11 */
	/* sum members: 65, holes: 1, sum holes: 1 */
	/* bit holes: 1, sum bit holes: 4 bits */
	/* padding: 6 */
	/* last cacheline: 8 bytes */
}

pahole after (note vlan_id):
struct net_bridge_fdb_entry {
	struct hlist_node          hlist;                /*     0    16 */
	struct net_bridge_port *   dst;                  /*    16     8 */
	long unsigned int          updated;              /*    24     8 */
	long unsigned int          used;                 /*    32     8 */
	mac_addr                   addr;                 /*    40     6 */
	__u16                      vlan_id;              /*    46     2 */
	unsigned char              is_local:1;           /*    48: 7  1 */
	unsigned char              is_static:1;          /*    48: 6  1 */
	unsigned char              added_by_user:1;      /*    48: 5  1 */
	unsigned char              added_by_external_learn:1; /*    48: 4  1 */

	/* XXX 4 bits hole, try to pack */
	/* XXX 7 bytes hole, try to pack */

	struct callback_head       rcu;                  /*    56    16 */
	/* --- cacheline 1 boundary (64 bytes) was 8 bytes ago --- */

	/* size: 72, cachelines: 2, members: 11 */
	/* sum members: 65, holes: 1, sum holes: 7 */
	/* bit holes: 1, sum bit holes: 4 bits */
	/* last cacheline: 8 bytes */
}
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Joe Stringer says:

====================
OPENVSWITCH && !NETFILTER build fix.

Fix issues reported by kbuild test robot:

All error/warnings (new ones prefixed by >>):

   net/openvswitch/actions.c: In function 'ovs_fragment':
>> net/openvswitch/actions.c:705:16: error: implicit declaration of
function 'nf_get_ipv6_ops' [-Werror=implicit-function-declaration]
      const struct nf_ipv6_ops *v6ops = nf_get_ipv6_ops();
                   ^
>> net/openvswitch/actions.c:705:37: warning: initialization makes
pointer from integer without a cast
      const struct nf_ipv6_ops *v6ops = nf_get_ipv6_ops();
                                        ^
>> net/openvswitch/actions.c:707:19: error: storage size of 'ovs_rt'
isn't known
      struct rt6_info ovs_rt;
                      ^
>> net/openvswitch/actions.c:724:8: error: dereferencing pointer to
incomplete type
      v6ops->fragment(skb->sk, skb, ovs_vport_output);
           ^
>> net/openvswitch/actions.c:707:19: warning: unused variable 'ovs_rt'
[-Wunused-variable]
      struct rt6_info ovs_rt;
                      ^
   cc1: some warnings being treated as errors
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

kbuild test robot reports that certain configurations will not
automatically pick up on the "struct rt6_info" definition, so explicitly
include the header for this structure.

Fixes: 7f8a436e "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When CONFIG_OPENVSWITCH is set, and CONFIG_NETFILTER is not set, the
openvswitch IPv6 fragmentation handling cannot refer to ipv6_ops because
it isn't defined. Add a dummy version to avoid #ifdefs in source files.

Fixes: 7f8a436e "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: small driver update

Ido Schimmel (2):
  mlxsw: Remove duplicate included header
  mlxsw: Make mailboxes 4KB aligned

Jiri Pirko (1):
  mlxsw: adjust transmit fail log message level in __mlxsw_emad_transmit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The HW-SW contract requires mailboxes passed to the firmware to be 4KB
aligned. Previously, these mailboxes were mapped using streaming DMA
routines, which do not guarantee the bus addresses to be 4KB aligned.
Under certain conditions this constraint was indeed violated and errors
were observed.

By using consistent DMA mapping routines together with a mailbox size of
4KB we are guaranteed not to violate the constraint.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When transmit fails, it is an error, not a warning.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
rocker: make master change handling nicer

Jiri Pirko (6):
  net: introduce change upper device notifier change info
  net: add netif_is_bridge_master helper
  net: add netif_is_ovs_master helper with IFF_OPENVSWITCH private flag
  net: kill long time unused bonding private flags
  rocker: use new helper to figure out master kind
  rocker: use change upper info
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Since now information about changed upper is passed along, benefit from
that and use this info directly.

This also fixes possible issues that could happen when non-master device
is added (current code does not distinguish between master and non-master
upper device).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>

Looking at rtnl kind string is kind of ugly. So use new helpers to do
this in nicer way.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>

We don't use them for years, just kill them now.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add this helper so code can easily figure out if netdev is openswitch.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add this helper so code can easily figure out if netdev is a bridge.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add info that is passed along with NETDEV_CHANGEUPPER event.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Usually an skb does not have up to MAX_SKB_FRAGS frags. So no need to
initialize the unuse part of sg. This patch initialize the sg based on
the real number it will used:

- during xmit, it could be inferred from nr_frags and can_push.
- for small receive buffer, it will also be 2.

Cc: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pravin B Shelar says:

====================
Geneve: Add support for tunnel metadata mode

Following patches adds support for Geneve tunnel metadata
mode. OVS can make use of Geneve net-device with tunnel
metadata API from kernel.

This also allows us to consolidate Geneve implementation
from two kernel modules geneve_core and geneve to single
geneve module. geneve_core module was targeted to share
Geneve encap and decap code between Geneve netdevice and
OVS Geneve tunnel implementation, Since OVS no longer
needs these API, Geneve code can be consolidated into
single geneve module.

v3-v4:
- Drop NETIF_F_NETNS_LOCAL feature.
- Fix geneve device newlink check

v2-v3:
- make tunnel medata device and regular device mutually exclusive.
- Fix Kconfig dependency for Geneve.
- Fix dst-port netlink encoding.
- drop changelink patch.

v1-v2:
- Replaced per hash table tunnel pointer (metadata enabled) with flag.
- Added support for changelink.
- Improve geneve device route lookup with more parameters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This change simplifies Geneve Tunnel hash table management.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Reviewed-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

geneve_core module handles send and receive functionality.
This way OVS could use the Geneve API. Now with use of
tunnel meatadata mode OVS can directly use Geneve netdevice.
So there is no need for separate module for Geneve. Following
patch consolidates Geneve protocol processing in single module.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

With help of tunnel metadata mode OVS can directly use
Geneve devices to implement Geneve tunnels.
This patch removes all of the OVS specific Geneve code
and make OVS use a Geneve net_device. Basic geneve vport
is still there to handle compatibility with current
userspace application.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following patch create new tunnel flag which enable
tunnel metadata collection on given device. These devices
can be used by tunnel metadata based routing or by OVS.
Geneve Consolidation patch get rid of collect_md_tun to
simplify tunnel lookup further.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add netlink interface to configure Geneve UDP port number.
So that user can configure it for a Gevene device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce function udp_tun_rx_dst() to initialize tunnel dst on
receive path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

On packet transmit path geneve need to lookup route. Following
patch improves route lookup using more parameters.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>