Move the skb_headroom check out of fr_hard_header and into pvc_xmit.
This has two benefits:

1. Originally we only do this check for skbs sent by users on Ethernet-
emulating PVC devices. After the change we do this check for skbs sent on
normal PVC devices, too.
(Also add a comment to make it clear that this is only a protection
against upper layers that don't take dev->needed_headroom into account.
Such upper layers should be rare and I believe they should be fixed.)

2. After the change we can simplify the parameter list of fr_hard_header.
We no longer need to use a pointer to pointers (skb_p) because we no
longer need to replace the skb inside fr_hard_header.

Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The MTU setting for this DSA switch is global so we need
to keep track of the MTU set for each port, then as soon
as any MTU changes, roof the MTU to the biggest common
denominator and poke that into the switch MTU setting.

To achieve this we need a per-chip-variant state container
for the RTL8366RB to use for the RTL8366RB-specific
stuff. Other SMI switches does seem to have per-port
MTU setting capabilities.

Fixes: 5f4a8ef3 ("net: dsa: rtl8366rb: Support setting MTU")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Better place for of_mdio.c is drivers/net/mdio.
Move of_mdio.c from drivers/of to drivers/net/mdio
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When packets are received on the error queue, this function under
net_ratelimit():

netif_err(priv, hw, net_dev, "Err FD status = 0x%08x\n");

does not get printed. Instead we only see:

[ 3658.845592] net_ratelimit: 244 callbacks suppressed
[ 3663.969535] net_ratelimit: 230 callbacks suppressed
[ 3669.085478] net_ratelimit: 228 callbacks suppressed

Enabling NETIF_MSG_HW fixes this issue, and we can see some information
about the frame descriptors of packets.
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Factor out handling the private packet/byte counters to new
functions rtl_get_priv_stats() and rtl_inc_priv_stats().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Obviously this driver version doesn't make sense. Go with the default
and let ethtool display the kernel version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make use of the new struct_size() helper instead of the offsetof() idiom.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'wireless-drivers-next-2020-10-09' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.10

Fourth and last set of patches for v5.10. Most of these are iwlwifi
patches, but few small fixes to other drivers as well.

Major changes:

iwlwifi

* PNVM support (platform-specific phy config data)

* bump the FW API support to 59
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'mac80211-next-for-net-next-2020-10-08' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next

Johannes Berg says:

====================
A handful of changes:
 * fixes for the recent S1G work
 * a docbook build time improvement
 * API to pass beacon rate to lower-level driver
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Johannes Berg says:

====================
netlink: export policy on validation failures

Export the policy used for attribute validation when it fails,
so e.g. for an out-of-range attribute userspace immediately gets
the valid ranges back.

v2 incorporates the suggestion from Jakub to have a function to
estimate the size (netlink_policy_dump_attr_size_estimate()) and
check that it does the right thing on the *normal* policy dumps,
not (just) when calling it from the error scenario.

v3 only addresses a few minor style issues.

v4 fixes up a forgotten 'git add' ... sorry.

v5 is a resend, I messed up v4's cover letter subject (saying v3)
and apparently the second patch didn't go out at all.

Tested using nl80211/iw in a few scenarios, seems to work fine
and return the policy back, e.g.

kernel reports: integer out of range
policy: 04 00 0b 00 0c 00 04 00 01 00 00 00 00 00 00 00
        ^ padding
                    ^ minimum allowed value
policy: 04 00 0b 00 0c 00 05 00 ff ff ff ff 00 00 00 00
        ^ padding
                    ^ maximum allowed value
policy: 08 00 01 00 04 00 00 00
        ^ type 4 == U32

for an out-of-range case.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add a new attribute NLMSGERR_ATTR_POLICY to the extended ACK
to advertise the policy, e.g. if an attribute was out of range,
you'll know the range that's permissible.

Add new NL_SET_ERR_MSG_ATTR_POL() and NL_SET_ERR_MSG_ATTR_POL()
macros to set this, since realistically it's only useful to do
this when the bad attribute (offset) is also returned.

Use it in lib/nlattr.c which practically does all the policy
validation.

v2:
 - add and use netlink_policy_dump_attr_size_estimate()
v3:
 - remove redundant break
v4:
 - really remove redundant break ... sorry
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Refactor the per-attribute policy writing into a new
helper function, to be used later for dumping out the
policy of a rejected attribute.

v2:
 - fix some indentation
v3:
 - change variable order in netlink_policy_dump_write()
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Karsten Graul says:

====================
net/smc: updates 2020-10-07

Patch 1 and 2 address warnings from static code checkers, and patch 3
handles a case when all proposed ISM V2 devices fail to init and no V1
devices are tried afterwards.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Field ini->smcd_version is set to SMC_V2 before calling
smc_listen_ism_init(). This clears the V1 bit that may be set. When all
matching ISM V2 devices fail to initialize then the smcd_version field
needs to get restored to allow any possible V1 devices to initialize.
And be consistent, always go to the not_found label when no device was
found.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

coccinelle informs about
net/smc/af_smc.c:1770:10-11: WARNING: opportunity for kzfree/kvfree_sensitive

Its not that kzfree() would help here, the memset() is done to prepare
the buffer for another socket receive.
Fix that warning message by reordering the calls, while at it eliminate
the unneeded variable cclc2 and use sizeof(*buf) as above in the same
function. No functional changes.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Static code checkers warn of inconsistent returns because the lgr mutex
is locked in one function and unlocked in a function called by the
locking function:
net/smc/af_smc.c:823 smc_connect_rdma() warn: inconsistent returns 'smc_client_lgr_pending'.
net/smc/af_smc.c:897 smc_connect_ism() warn: inconsistent returns 'smc_server_lgr_pending'.

Make the code consistent by doing the unlock in the same function that
fetches the lock. No functional changes.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'linux-can-next-for-5.10-20201007' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next

Marc Kleine-Budde says:

====================
linux-can-next-for-5.10-20201007

The first 3 patches are by me and fix several warnings found
when compiling the  kernel with W=1.

Lukas Bulwahn's patch adjusts the MAINTAINERS file, to accommodate
the renaming of the mcp251xfd driver.

Vincent Mailhol contributes 3 patches for the CAN networking layer.
First error queue support is added the the CAN RAW protocol.
The second patch converts the get_can_dlc() and get_canfd_dlc()
in-Kernel-only macros from using __u8 to u8.
The third patch adds a helper function to calculate the length of
one bit in in multiple of time quanta.

Oliver Hartkopp's patch add support for the ISO 15765-2:2016
transport protocol to the CAN stack.

Three patches by Lad Prabhakar add documentation for various
new rcar controllers to the device tree bindings of the rcar_can
and rcan_canfd driver.

Michael Walle's patch adds various processors to the flexcan
driver binding documentation.

The next two patches are by me and target the flexcan driver aswell.
The remove the ack_grp and ack_bit from the fsl,stop-mode DT property
and the driver, as they are not used anymore. As these are the last
two arguments this change will not break existing device trees.

The last three patches are by Srinivas Neeli and target
the xilinx_can driver.
The first one increases the lower limit for the bit rate
prescaler to 2, the other two fix sparse and coverity findings.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
100GbE Intel Wired LAN Driver Updates 2020-10-07

This series contains updates to ice driver only.

Andy Shevchenko changes usage to %*phD format to print small buffer as hex
string.

Bruce removes repeated words reported by checkpatch.

Ani changes ice_info_get_dsn() to return void as it always returns
success.

Jake adds devlink reporting of fw.app.bundle_id. Moves devlink_port
structure to ice_vsi to resolve issues with cleanup. Adds additional
debug info for firmware updates.

Bixuan Cui resolves -Wpointer-to-int-cast warnings.

Dan adds additional packet type masks and checks to prevent overwriting
existing Flow Director rules.
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A subsequent addition of an IP4 or IP6 rule after other rules would
overwrite any existing TCAM entries of related L4 protocols(ex: tcp4 or
udp6). This was due to the mask including too many TCAM entries. Add new
packet type masks with bits properly excluded so rules are not overwritten.
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

pointers should be casted to unsigned long to avoid
-Wpointer-to-int-cast warnings:

drivers/net/ethernet/intel/ice/ice_flow.h:197:33: warning:
    cast from pointer to integer of different size
drivers/net/ethernet/intel/ice/ice_flow.h:198:32: warning:
    cast to pointer from integer of different size
Signed-off-by: Bixuan Cui <cuibixuan@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

While debugging a recent failure to update the flash of an ice device,
I found it helpful to add additional logging which helped determine the
root cause of the problem being a timeout issue.

Add some extra dev_dbg() logging messages which can be enabled using the
dynamic debug facility, including one for ice_aq_wait_for_event that
will use jiffies to capture a rough estimate of how long we waited for
the completion of a firmware command.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, the devlink_port structure is stored within the ice_pf. This
made sense because we create a single devlink_port for each PF. This
setup does not mesh with the abstractions in the driver very well, and
led to a flow where we accidentally call devlink_port_unregister twice
during error cleanup.

In particular, if devlink_port_register or devlink_port_unregister are
called twice, this leads to a kernel panic. This appears to occur during
some possible flows while cleaning up from a failure during driver
probe.

If register_netdev fails, then we will call devlink_port_unregister in
ice_cfg_netdev as it cleans up. Later, we again call
devlink_port_unregister since we assume that we must cleanup the port
that is associated with the PF structure.

This occurs because we cleanup the devlink_port for the main PF even
though it was not allocated. We allocated the port within a per-VSI
function for managing the main netdev, but did not release the port when
cleaning up that VSI, the allocation and destruction are not aligned.

Instead of attempting to manage the devlink_port as part of the PF
structure, manage it as part of the PF VSI. Doing this has advantages,
as we can match the de-allocation of the devlink_port with the
unregister_netdev associated with the main PF VSI.

Moving the port to the VSI is preferable as it paves the way for
handling devlink ports allocated for other purposes such as SR-IOV VFs.

Since we're changing up how we allocate the devlink_port, also change
the indexing. Originally, we indexed the port using the PF id number.
This came from an old goal of sharing a devlink for each physical
function. Managing devlink instances across multiple function drivers is
not workable. Instead, lets set the port number to the logical port
number returned by firmware and set the index using the VSI index
(sometimes referred to as VSI handle).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add "fw.app.bundle_id" to display the DDP Track ID of the active DDP
package. This id is similar to "fw.bundle_id" and is a unique identifier
for the DDP package that is loaded in the device. Each new DDP has
a unique Track ID generated for it, and the ID can be used to identify
and track the DDP package.

Add documentation for the new devlink info version.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

ice_info_get_dsn always returns 0, so just make it void.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

A new test in checkpatch detects repeated words; cleanup all pre-existing
occurrences of those now.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Co-developed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Use %*phD format to print small buffer as hex string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for the KSZ9563 3-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9563 supports both SPI (already in) and I2C. The
ksz9563 is already in the device tree binding documentation.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

RDS/IB tries to refill the recv buffer in softirq context using
GFP_NOWAIT flag. However alloc failure is handled by queueing a work to
refill the recv buffer with GFP_KERNEL flag. This means failure to
allocate with GFP_NOWAIT isn't fatal. Do not print the PAF warnings if
softirq context fails to refill the recv buffer. We will see the PAF
warnings when worker also fails to allocate.
Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Reviewed-by: Aruna Ramakrishna <aruna.ramakrishna@oracle.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Moshe Shemesh says:

====================
Add devlink reload action and limit options

Introduce new options on devlink reload API to enable the user to select
the reload action required and constrains limits on these actions that he
may want to ensure. Complete support for reload actions in mlx5.
The following reload actions are supported:
  driver_reinit: driver entities re-initialization, applying devlink-param
                 and devlink-resource values.
  fw_activate: firmware activate.

The uAPI is backward compatible, if the reload action option is omitted
from the reload command, the driver reinit action will be used.
Note that when required to do firmware activation some drivers may need
to reload the driver. On the other hand some drivers may need to reset
the firmware to reinitialize the driver entities. Therefore, the devlink
reload command returns the actions which were actually performed.

By default reload actions are not limited and driver implementation may
include reset or downtime as needed to perform the actions.
However, if reload limit is selected, the driver should perform only if
it can do it while keeping the limit constraints.
Reload limit added:
  no_reset: No reset allowed, no down time allowed, no link flap and no
            configuration is lost.

Each driver which supports devlink reload command should expose the
reload actions and limits supported.

Add reload stats to hold the history per reload action per limit.
For example, the number of times fw_activate has been done on this
device since the driver module was added or if the firmware activation
was done with or without reset.

Patch 1 changes devlink_reload_supported() param type to enable using
        it before allocating devlink.
Patch 2-3 add the new API reload action and reload limit options to
          devlink reload.
Patch 4-5 add reload stats and remote reload stats. These stats are
          exposed through devlink dev get.
Patches 6-11 add support on mlx5 for devlink reload action fw_activate
            and handle the firmware reset events.
Patches 12-13 add devlink enable remote dev reset parameter and use it
             in mlx5.
Patches 14-15 mlx5 add devlink reload limit no_reset support for
              fw_activate reload action.
Patch 16 adds documentation file devlink-reload.rst
====================
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add devlink reload rst documentation file.
Update index file to include it.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for devlink reload action fw_activate with reload limit
no_reset which does firmware live patching, updating the firmware image
without reset, no downtime and no configuration lose. The driver checks
if the firmware is capable of handling the pending firmware changes as a
live patch. If it is then it triggers firmware live patching flow.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Firmware live patch event notifies the driver that the firmware was just
updated using live patch. In such case the driver should not reload or
re-initiate entities, part to updating the firmware version and
re-initiate the firmware tracer which can be updated by live patch with
new strings database to help debugging an issue.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The enable_remote_dev_reset devlink param flags that the host admin
allows resets by other hosts. In case it is cleared mlx5 host PF driver
will send NACK on pci sync for firmware update reset request and the
command will fail.
By default enable_remote_dev_reset parameter is true, so pci sync for
firmware update reset is enabled.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The enable_remote_dev_reset devlink param flags that the host admin
allows device resets that can be initiated by other hosts. This
parameter is useful for setups where a device is shared by different
hosts, such as multi-host setup. Once the user set this parameter to
false, the driver should NACK any attempt to reset the device while the
driver is loaded.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add support for devlink reload action fw_activate. To activate firmware
image the mlx5 driver resets the firmware and reloads it from flash. If
a new image was stored on flash it will be loaded. Once this reload
command is executed the driver initiates fw sync reset flow, where the
firmware synchronizes all PFs on coming reset and driver reload.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

If firmware sends sync_reset_abort to driver the driver should clear the
reset requested mode as reset is not expected any more.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

On sync_reset_now event the driver does reload and PCI link toggle to
activate firmware upgrade reset. When the firmware sends this event it
syncs the event on all PFs, so all PFs will do PCI link toggle at once.
To do PCI link toggle, the driver ensures that no other device ID under
the same bridge by checking that all the PF functions under the same PCI
bridge have same device ID. If no other device it uses PCI bridge link
control to turn link down and up.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Once the driver gets sync_reset_request from firmware it prepares for the
coming reset and sends acknowledge.
After getting this event the driver expects device reset, either it will
trigger PCI reset on sync_reset_now event or such PCI reset will be
triggered by another PF of the same device. So it moves to reset
requested mode and if it gets PCI reset triggered by the other PF it
detect the reset and reloads.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Set capability to notify the firmware that this host driver is capable
of handling pci sync for firmware update events.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Add functions to query and set the MFRL reset options supported by
firmware.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>