For mapped IRQs (with the HW bit set in the LR) we have to follow some
rules of the architecture.  One of these rules is that VM must not be
allowed to deactivate a virtual interrupt with the HW bit set unless the
physical interrupt is also active.

This works fine when injecting mapped interrupts, because we leave it up
to the injector to either set EOImode==1 or manually set the active
state of the physical interrupt.

However, the guest can set virtual interrupt to be pending or active by
writing to the virtual distributor, which could lead to deactivating a
virtual interrupt with the HW bit set without the physical interrupt
being active.

We could set the physical interrupt to active whenever we are about to
enter the VM with a HW interrupt either pending or active, but that
would be really slow, especially on GICv2.  So we take the long way
around and do the hard work when needed, which is expected to be
extremely rare.

When the VM sets the pending state for a HW interrupt on the virtual
distributor we set the active state on the physical distributor, because
the virtual interrupt can become active and then the guest can
deactivate it.

When the VM clears the pending state we also clear it on the physical
side, because the injector might otherwise raise the interrupt.  We also
clear the physical active state when the virtual interrupt is not
active, since otherwise a SPEND/CPEND sequence from the guest would
prevent signaling of future interrupts.

Changing the state of mapped interrupts from userspace is not supported,
and it's expected that userspace unmaps devices from VFIO before
attempting to set the interrupt state, because the interrupt state is
driven by hardware.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

The GIC sometimes need to sample the physical line of a mapped
interrupt.  As we know this to be notoriously slow, provide a callback
function for devices (such as the timer) which can do this much faster
than talking to the distributor, for example by comparing a few
in-memory values.  Fall back to the good old method of poking the
physical GIC if no callback is provided.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Level-triggered mapped IRQs are special because we only observe rising
edges as input to the VGIC, and we don't set the EOI flag and therefore
are not told when the level goes down, so that we can re-queue a new
interrupt when the level goes up.

One way to solve this problem is to side-step the logic of the VGIC and
special case the validation in the injection path, but it has the
unfortunate drawback of having to peak into the physical GIC state
whenever we want to know if the interrupt is pending on the virtual
distributor.

Instead, we can maintain the current semantics of a level triggered
interrupt by sort of treating it as an edge-triggered interrupt,
following from the fact that we only observe an asserting edge.  This
requires us to be a bit careful when populating the LRs and when folding
the state back in though:

 * We lower the line level when populating the LR, so that when
   subsequently observing an asserting edge, the VGIC will do the right
   thing.

 * If the guest never acked the interrupt while running (for example if
   it had masked interrupts at the CPU level while running), we have
   to preserve the pending state of the LR and move it back to the
   line_level field of the struct irq when folding LR state.

   If the guest never acked the interrupt while running, but changed the
   device state and lowered the line (again with interrupts masked) then
   we need to observe this change in the line_level.

   Both of the above situations are solved by sampling the physical line
   and set the line level when folding the LR back.

 * Finally, if the guest never acked the interrupt while running and
   sampling the line reveals that the device state has changed and the
   line has been lowered, we must clear the physical active state, since
   we will otherwise never be told when the interrupt becomes asserted
   again.

This has the added benefit of making the timer optimization patches
(https://lists.cs.columbia.edu/pipermail/kvmarm/2017-July/026343.html) a
bit simpler, because the timer code doesn't have to clear the active
state on the sync anymore.  It also potentially improves the performance
of the timer implementation because the GIC knows the state or the LR
and only needs to clear the
active state when the pending bit in the LR is still set, where the
timer has to always clear it when returning from running the guest with
an injected timer interrupt.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

The timer logic was designed after a strict idea of modeling an
interrupt line level in software, meaning that only transitions in the
level need to be reported to the VGIC.  This works well for the timer,
because the arch timer code is in complete control of the device and can
track the transitions of the line.

However, as we are about to support using the HW bit in the VGIC not
just for the timer, but also for VFIO which cannot track transitions of
the interrupt line, we have to decide on an interface between the GIC
and other subsystems for level triggered mapped interrupts, which both
the timer and VFIO can use.

VFIO only sees an asserting transition of the physical interrupt line,
and tells the VGIC when that happens.  That means that part of the
interrupt flow is offloaded to the hardware.

To use the same interface for VFIO devices and the timer, we therefore
have to change the timer (we cannot change VFIO because it doesn't know
the details of the device it is assigning to a VM).

Luckily, changing the timer is simple, we just need to stop 'caching'
the line level, but instead let the VGIC know the state of the timer
every time there is a potential change in the line level, and when the
line level should be asserted from the timer ISR.  The VGIC can ignore
extra notifications using its validate mechanism.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Julien Thierry <julien.thierry@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

We are about to distinguish between userspace accesses and mmio traps
for a number of the mmio handlers.  When the requester vcpu is NULL, it
means we are handling a userspace access.

Factor out the functionality to get the request vcpu into its own
function, mostly so we have a common place to document the semantics of
the return value.

Also take the chance to move the functionality outside of holding a
spinlock and instead explicitly disable and enable preemption.  This
supports PREEMPT_RT kernels as well.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

The __this_cpu_read() and __this_cpu_write() functions already implement
checks for the required preemption levels when using
CONFIG_DEBUG_PREEMPT which gives you nice error messages and such.
Therefore there is no need to explicitly check this using a BUG_ON() in
the code (which we don't do for other uses of per cpu variables either).
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Fix ptr_ret.cocci warnings:
virt/kvm/arm/vgic/vgic-its.c:971:1-3: WARNING: PTR_ERR_OR_ZERO can be used

Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

Since commit 93390c0a ("arm64: KVM: Hide unsupported AArch64 CPU
features from guests") we can hide cpu features from guests. Apply
this to a long standing issue where guests see a PMU available, but
it's not, because it was not enabled by KVM's userspace.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>

HPFS does not set SB_I_VERSION and does not use the i_version counter
internally.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Mikulas Patocka <mikulas@twibright.com>
Reviewed-by: Mikulas Patocka <mikulas@twibright.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

sign_extend32 counts the sign bit parameter from 0, not from 1.  So we
have to use "11" for 12th bit, not "12".

This mistake means we have not allowed negative op and cmp args since
commit 30d6e0a4 ("futex: Remove duplicated code and fix undefined
behaviour") till now.

Fixes: 30d6e0a4 ("futex: Remove duplicated code and fix undefined behaviour")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Darren Hart <dvhart@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull btrfs fixes from David Sterba:
 "This contains a few fixes (error handling, quota leak, FUA vs
  nobarrier mount option).

  There's one one worth mentioning separately - an off-by-one fix that
  leads to overwriting first byte of an adjacent page with 0, out of
  bounds of the memory allocated by an ioctl. This is under a privileged
  part of the ioctl, can be triggerd in some subvolume layouts"

* tag 'for-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: Fix possible off-by-one in btrfs_search_path_in_tree
  Btrfs: disable FUA if mounted with nobarrier
  btrfs: fix missing error return in btrfs_drop_snapshot
  btrfs: handle errors while updating refcounts in update_ref_for_cow
  btrfs: Fix quota reservation leak on preallocated files

Pull ARM SoC fixes from Olof Johansson:

 - A revert of all SCPI changes from the 4.15 merge window. They had
   regressions on the Amlogic platforms, and the submaintainer isn't
   around to fix these bugs due to vacation, etc. So we agreed to revert
   and revisit in next release cycle.

 - A series fixing a number of bugs for ARM CCN interconnect, around
   module unload, smp_processor_id() in preemptable context, and fixing
   some memory allocation failure checks.

 - A handful of devicetree fixes for different platforms, fixing
   warnings and errors that were previously ignored by the compiler.

 - The usual set of mostly minor fixes for different platforms.

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
  ARM64: dts: meson-gx: fix UART pclk clock name
  ARM: omap2: hide omap3_save_secure_ram on non-OMAP3 builds
  arm: dts: nspire: Add missing #phy-cells to usb-nop-xceiv
  ARM: dts: Fix dm814x missing phy-cells property
  ARM: dts: Fix elm interrupt compiler warning
  bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
  bus: arm-cci: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Simplify code
  bus: arm-ccn: Check memory allocation failure
  bus: arm-ccn: constify attribute_group structures.
  firmware: arm_scpi: Revert updates made during v4.15 merge window
  arm: dts: marvell: Add missing #phy-cells to usb-nop-xceiv
  arm64: dts: sort vendor subdirectories in Makefile alphabetically
  meson-gx-socinfo: Fix package id parsing
  ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
  ARM: dts: meson: fix the memory region of the GPIO interrupt controller
  ARM: dts: meson: correct the sort order for the the gpio_intc node
  MAINTAINERS: exclude other Socionext SoC DT files from ARM/UNIPHIER entry
  arm64: dts: uniphier: remove unnecessary interrupt-parent
  ...

Pull KVM fixes from Radim Krčmář:
 "ARM:
   - A number of issues in the vgic discovered using SMATCH
   - A bit one-off calculation in out stage base address mask (32-bit
     and 64-bit)
   - Fixes to single-step debugging instructions that trap for other
     reasons such as MMMIO aborts
   - Printing unavailable hyp mode as error
   - Potential spinlock deadlock in the vgic
   - Avoid calling vgic vcpu free more than once
   - Broken bit calculation for big endian systems

 s390:
   - SPDX tags
   - Fence storage key accesses from problem state
   - Make sure that irq_state.flags is not used in the future

  x86:
   - Intercept port 0x80 accesses to prevent host instability (CVE)
   - Use userspace FPU context for guest FPU (mainly an optimization
     that fixes a double use of kernel FPU)
   - Do not leak one page per module load
   - Flush APIC page address cache from MMU invalidation notifiers"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
  KVM: x86: fix APIC page invalidation
  KVM: s390: Fix skey emulation permission check
  KVM: s390: mark irq_state.flags as non-usable
  KVM: s390: Remove redundant license text
  KVM: s390: add SPDX identifiers to the remaining files
  KVM: VMX: fix page leak in hardware_setup()
  KVM: VMX: remove I/O port 0x80 bypass on Intel hosts
  x86,kvm: remove KVM emulator get_fpu / put_fpu
  x86,kvm: move qemu/guest FPU switching out to vcpu_run
  KVM: arm/arm64: Fix broken GICH_ELRSR big endian conversion
  KVM: arm/arm64: kvm_arch_destroy_vm cleanups
  KVM: arm/arm64: Fix spinlock acquisition in vgic_set_owner
  kvm: arm: don't treat unavailable HYP mode as an error
  KVM: arm/arm64: Avoid attempting to load timer vgic state without a vgic
  kvm: arm64: handle single-step of hyp emulated mmio instructions
  kvm: arm64: handle single-step during SError exceptions
  kvm: arm64: handle single-step of userspace mmio instructions
  kvm: arm64: handle single-stepping trapped instructions
  KVM: arm/arm64: debug: Introduce helper for single-step
  arm: KVM: Fix VTTBR_BADDR_MASK BUG_ON off-by-one
  ...

* fixes:
  ARM64: dts: meson-gx: fix UART pclk clock name
  ARM: dts: Fix dm814x missing phy-cells property
  ARM: dts: Fix elm interrupt compiler warning
  bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
  bus: arm-cci: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Simplify code
  bus: arm-ccn: Check memory allocation failure
  bus: arm-ccn: constify attribute_group structures.
  meson-gx-socinfo: Fix package id parsing
  ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
  ARM: dts: meson: fix the memory region of the GPIO interrupt controller
  ARM: dts: meson: correct the sort order for the the gpio_intc node

Merge tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes

Amlogic fixes for v4.15-rc
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo

* tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gx: fix UART pclk clock name
  meson-gx-socinfo: Fix package id parsing
  ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
  ARM: dts: meson: fix the memory region of the GPIO interrupt controller
  ARM: dts: meson: correct the sort order for the the gpio_intc node
Signed-off-by: Olof Johansson <olof@lixom.net>

bus: ARM CCN and CCI PMU driver fixes

This is a bunch of fixes CCN and (guest starring this time) CCI drivers.

* Check for potential of failed allocation for the driver name string
* Manage CPU ID properly at allocation (both CCN and CCI)
* Fix module unload warnings related to objects release order
* Small improvements like using allocating printfs and proper
  attributes constification

The one fixing potential issues have been cc-ed to stable.

* tag 'ccn/fixes-for-4.15' of git://git.linaro.org/people/pawel.moll/linux:
  bus: arm-ccn: fix module unloading Error: Removing state 147 which has instances left.
  bus: arm-cci: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Fix use of smp_processor_id() in preemptible context
  bus: arm-ccn: Simplify code
  bus: arm-ccn: Check memory allocation failure
  bus: arm-ccn: constify attribute_group structures.
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Two fixes for dts compiler warnings

These recently started showing up with better dtc checks being
introduced.

* tag 'omap-for-v4.15/fixes-dt-warnings' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: Fix dm814x missing phy-cells property
  ARM: dts: Fix elm interrupt compiler warning
Signed-off-by: Olof Johansson <olof@lixom.net>

Merge tag 'keys-fixes-20171208' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs into keys-for-linus

Assorted fixes for keyrings, ASN.1, X.509 and PKCS#7.

Commit 4675ff05 ("kmemcheck: rip it out") has removed the code but
for some reason SPDX header stayed in place.  This looks like a rebase
mistake in the mmotm tree or the merge mistake.  Let's drop those
leftovers as well.
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:

 1) CAN fixes from Martin Kelly (cancel URBs properly in all the CAN usb
    drivers).

 2) Revert returning -EEXIST from __dev_alloc_name() as this propagates
    to userspace and broke some apps. From Johannes Berg.

 3) Fix conn memory leaks and crashes in TIPC, from Jon Malloc and Cong
    Wang.

 4) Gianfar MAC can't do EEE so don't advertise it by default, from
    Claudiu Manoil.

 5) Relax strict netlink attribute validation, but emit a warning. From
    David Ahern.

 6) Fix regression in checksum offload of thunderx driver, from Florian
    Westphal.

 7) Fix UAPI bpf issues on s390, from Hendrik Brueckner.

 8) New card support in iwlwifi, from Ihab Zhaika.

 9) BBR congestion control bug fixes from Neal Cardwell.

10) Fix port stats in nfp driver, from Pieter Jansen van Vuuren.

11) Fix leaks in qualcomm rmnet, from Subash Abhinov Kasiviswanathan.

12) Fix DMA API handling in sh_eth driver, from Thomas Petazzoni.

13) Fix spurious netpoll warnings in bnxt_en, from Calvin Owens.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (67 commits)
  net: mvpp2: fix the RSS table entry offset
  tcp: evaluate packet losses upon RTT change
  tcp: fix off-by-one bug in RACK
  tcp: always evaluate losses in RACK upon undo
  tcp: correctly test congestion state in RACK
  bnxt_en: Fix sources of spurious netpoll warnings
  tcp_bbr: reset long-term bandwidth sampling on loss recovery undo
  tcp_bbr: reset full pipe detection on loss recovery undo
  tcp_bbr: record "full bw reached" decision in new full_bw_reached bit
  sfc: pass valid pointers from efx_enqueue_unwind
  gianfar: Disable EEE autoneg by default
  tcp: invalidate rate samples during SACK reneging
  can: peak/pcie_fd: fix potential bug in restarting tx queue
  can: usb_8dev: cancel urb on -EPIPE and -EPROTO
  can: kvaser_usb: cancel urb on -EPIPE and -EPROTO
  can: esd_usb2: cancel urb on -EPIPE and -EPROTO
  can: ems_usb: cancel urb on -EPIPE and -EPROTO
  can: mcba_usb: cancel urb on -EPROTO
  usbnet: fix alignment for frames with no ethernet header
  tcp: use current time in tcp_rcv_space_adjust()
  ...

Pull media fixes from Mauro Carvalho Chehab:

 "A series of fixes for the media subsytem:

   - The largest amount of fixes in this series is with regards to
     comments that aren't kernel-doc, but start with "/**".

     A new check added for 4.15 makes it to produce a *huge* amount of
     new warnings (I'm compiling here with W=1). Most of the patches in
     this series fix those.

     No code changes - just comment changes at the source files

   - rc: some fixed in order to better handle RC repetition codes

   - v4l-async: use the v4l2_dev from the root notifier when matching
     sub-devices

   - v4l2-fwnode: Check subdev count after checking port

   - ov 13858 and et8ek8: compilation fix with randconfigs

   - usbtv: a trivial new USB ID addition

   - dibusb-common: don't do DMA on stack on firmware load

   - imx274: Fix error handling, add MAINTAINERS entry

   - sir_ir: detect presence of port"

* tag 'media/v4.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (50 commits)
  media: imx274: Fix error handling, add MAINTAINERS entry
  media: v4l: async: use the v4l2_dev from the root notifier when matching sub-devices
  media: v4l2-fwnode: Check subdev count after checking port
  media: et8ek8: select V4L2_FWNODE
  media: ov13858: Select V4L2_FWNODE
  media: rc: partial revert of "media: rc: per-protocol repeat period"
  media: dvb: i2c transfers over usb cannot be done from stack
  media: dvb-frontends: complete kernel-doc markups
  media: docs: add documentation for frontend attach info
  media: dvb_frontends: fix kernel-doc macros
  media: drivers: remove "/**" from non-kernel-doc comments
  media: lm3560: add a missing kernel-doc parameter
  media: rcar_jpu: fix two kernel-doc markups
  media: vsp1: add a missing kernel-doc parameter
  media: soc_camera: fix a kernel-doc markup
  media: mt2063: fix some kernel-doc warnings
  media: radio-wl1273: fix a parameter name at kernel-doc macro
  media: s3c-camif: add missing description at s3c_camif_find_format()
  media: mtk-vpu: add description for wdt fields at struct mtk_vpu
  media: vdec: fix some kernel-doc warnings
  ...

Pull drm fixes from Dave Airlie:
 "This pull is a bit larger than I'd like but a large bunch of it is
  license fixes, AMD wanted to fix the licenses for a bunch of files
  that were missing them,

 Otherwise a bunch of TTM regression fix since the hugepage support,
 some i915 and gvt fixes, a core connector free in a safe context fix,
 and one bridge fix"

* tag 'drm-fixes-for-v4.15-rc3' of git://people.freedesktop.org/~airlied/linux: (26 commits)
  drm/bridge: analogix dp: Fix runtime PM state in get_modes() callback
  Revert "drm/i915: Display WA #1133 WaFbcSkipSegments:cnl, glk"
  drm/vc4: Fix false positive WARN() backtrace on refcount_inc() usage
  drm/i915: Call i915_gem_init_userptr() before taking struct_mutex
  drm/exynos: remove unnecessary function declaration
  drm/exynos: remove unnecessary descrptions
  drm/exynos: gem: Drop NONCONTIG flag for buffers allocated without IOMMU
  drm/exynos: Fix dma-buf import
  drm/ttm: swap consecutive allocated pooled pages v4
  drm: safely free connectors from connector_iter
  drm/i915/gvt: set max priority for gvt context
  drm/i915/gvt: Don't mark vgpu context as inactive when preempted
  drm/i915/gvt: Limit read hw reg to active vgpu
  drm/i915/gvt: Export intel_gvt_render_mmio_to_ring_id()
  drm/i915/gvt: Emulate PCI expansion ROM base address register
  drm/ttm: swap consecutive allocated cached pages v3
  drm/ttm: roundup the shrink request to prevent skip huge pool
  drm/ttm: add page order support in ttm_pages_put
  drm/ttm: add set_pages_wb for handling page order more than zero
  drm/ttm: add page order in page pool
  ...

Pull md fixes from Shaohua Li:
 "Some MD fixes.

  The notable one is a raid5-cache deadlock bug with dm-raid, others are
  not significant"

* tag 'md/4.15-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md/raid1/10: add missed blk plug
  md: limit mdstat resync progress to max_sectors
  md/r5cache: move mddev_lock() out of r5c_journal_mode_set()
  md/raid5: correct degraded calculation in raid5_error

Merge tag 'devicetree-fixes-for-4.15-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull DeviceTree fixes from Rob Herring:
 "Another set of DT fixes:

   - Fixes from overlay code rework. A trifecta of fixes to the locking,
     an out of bounds access, and a memory leak in of_overlay_apply()

   - Clean-up at25 eeprom binding document

   - Remove leading '0x' in unit-addresses from binding docs"

* tag 'devicetree-fixes-for-4.15-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  of: overlay: Make node skipping in init_overlay_changeset() clearer
  of: overlay: Fix out-of-bounds write in init_overlay_changeset()
  of: overlay: Fix (un)locking in of_overlay_apply()
  of: overlay: Fix memory leak in of_overlay_apply() error path
  dt-bindings: eeprom: at25: Document device-specific compatible values
  dt-bindings: eeprom: at25: Grammar s/are can/can/
  dt-bindings: Remove leading 0x from bindings notation
  of: overlay: Remove else after goto
  of: Spelling s/changset/changeset/
  of: unittest: Remove bogus overlay mutex release from overlay_data_add()

Pull virtio bugfixes from Michael Tsirkin:
 "A couple of minor bugfixes"

* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
  virtio_net: fix return value check in receive_mergeable()
  virtio_mmio: add cleanup for virtio_mmio_remove
  virtio_mmio: add cleanup for virtio_mmio_probe

Pull xen fixes from Juergen Gross:
 "Just two small fixes for the new pvcalls frontend driver"

* tag 'for-linus-4.15-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/pvcalls: Fix a check in pvcalls_front_remove()
  xen/pvcalls: check for xenbus_read() errors

Pull powerpc fixes from Michael Ellerman:

 "One notable fix for kexec on Power9, where we were not clearing MMU
  PID properly which sometimes leads to hangs. Finally debugged to a
  root cause by Nick.

  A revert of a patch which tried to rework our panic handling to get
  more output on the console, but inadvertently broke reporting the
  panic to the hypervisor, which apparently people care about.

  Then a fix for an oops in the PMU code, and finally some s/%p/%px/ in
  xmon.

  Thanks to: David Gibson, Nicholas Piggin, Ravi Bangoria"

* tag 'powerpc-4.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/xmon: Don't print hashed pointers in xmon
  powerpc/64s: Initialize ISAv3 MMU registers before setting partition table
  Revert "powerpc: Do not call ppc_md.panic in fadump panic notifier"
  powerpc/perf: Fix oops when grouping different pmu events

Merge tag 'linux-can-fixes-for-4.15-20171208' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2017-12-08

this is a pull request of 6 patches for net/master.

Martin Kelly provides 5 patches for various USB based CAN drivers, that
properly cancel the URBs on adapter unplug, so that the driver doesn't
end up in an endless loop. Stephane Grosjean provides a patch to restart
the tx queue if zero length packages are transmitted.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2017-12-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

Kalle Valo says:

====================
wireless-drivers fixes for 4.15

Second set of fixes for 4.15. This time a lot of iwlwifi patches and
two brcmfmac patches. Most important here are the MIC and IVC fixes
for iwlwifi to unbreak 9000 series.

iwlwifi

* fix rate-scaling to not start lowest possible rate

* fix the TX queue hang detection for AP/GO modes

* fix the TX queue hang timeout in monitor interfaces

* fix packet injection

* remove a wrong error message when dumping PCI registers

* fix race condition with RF-kill

* tell mac80211 when the MIC has been stripped (9000 series)

* tell mac80211 when the IVC has been stripped (9000 series)

* add 2 new PCI IDs, one for 9000 and one for 22000

* fix a queue hang due during a P2P Remain-on-Channel operation

brcmfmac

* fix a race which sometimes caused a crash during sdio unbind

* fix a kernel-doc related build error
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The macro used to access or set an RSS table entry was using an offset
of 8, while it should use an offset of 0. This lead to wrongly configure
the RSS table, not accessing the right entries.

Fixes: 1d7d15d7 ("net: mvpp2: initialize the RSS tables")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuchung Cheng says:

====================
tcp: RACK loss recovery bug fixes

This patch set has four minor bug fixes in TCP RACK loss recovery.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

RACK skips an ACK unless it advances the most recently delivered
TX timestamp (rack.mstamp). Since RACK also uses the most recent
RTT to decide if a packet is lost, RACK should still run the
loss detection whenever the most recent RTT changes. For example,
an ACK that does not advance the timestamp but triggers the cwnd
undo due to reordering, would then use the most recent (higher)
RTT measurement to detect further losses.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RACK should mark a packet lost when remaining wait time is zero.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When sender detects spurious retransmission, all packets
marked lost are remarked to be in-flight. However some may
be considered lost based on its timestamps in RACK. This patch
forces RACK to re-evaluate, which may be skipped previously if
the ACK does not advance RACK timestamp.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RACK does not test the loss recovery state correctly to compute
the reordering window. It assumes if lost_out is zero then TCP is
not in loss recovery. But it can be zero during recovery before
calling tcp_rack_detect_loss(): when an ACK acknowledges all
packets marked lost before receiving this ACK, but has not yet
to discover new ones by tcp_rack_detect_loss(). The fix is to
simply test the congestion state directly.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After applying 2270bc5d ("bnxt_en: Fix netpoll handling") and
903649e7 ("bnxt_en: Improve -ENOMEM logic in NAPI poll loop."),
we still see the following WARN fire:

  ------------[ cut here ]------------
  WARNING: CPU: 0 PID: 1875170 at net/core/netpoll.c:165 netpoll_poll_dev+0x15a/0x160
  bnxt_poll+0x0/0xd0 exceeded budget in poll
  <snip>
  Call Trace:
   [<ffffffff814be5cd>] dump_stack+0x4d/0x70
   [<ffffffff8107e013>] __warn+0xd3/0xf0
   [<ffffffff8107e07f>] warn_slowpath_fmt+0x4f/0x60
   [<ffffffff8179519a>] netpoll_poll_dev+0x15a/0x160
   [<ffffffff81795f38>] netpoll_send_skb_on_dev+0x168/0x250
   [<ffffffff817962fc>] netpoll_send_udp+0x2dc/0x440
   [<ffffffff815fa9be>] write_ext_msg+0x20e/0x250
   [<ffffffff810c8125>] call_console_drivers.constprop.23+0xa5/0x110
   [<ffffffff810c9549>] console_unlock+0x339/0x5b0
   [<ffffffff810c9a88>] vprintk_emit+0x2c8/0x450
   [<ffffffff810c9d5f>] vprintk_default+0x1f/0x30
   [<ffffffff81173df5>] printk+0x48/0x50
   [<ffffffffa0197713>] edac_raw_mc_handle_error+0x563/0x5c0 [edac_core]
   [<ffffffffa0197b9b>] edac_mc_handle_error+0x42b/0x6e0 [edac_core]
   [<ffffffffa01c3a60>] sbridge_mce_output_error+0x410/0x10d0 [sb_edac]
   [<ffffffffa01c47cc>] sbridge_check_error+0xac/0x130 [sb_edac]
   [<ffffffffa0197f3c>] edac_mc_workq_function+0x3c/0x90 [edac_core]
   [<ffffffff81095f8b>] process_one_work+0x19b/0x480
   [<ffffffff810967ca>] worker_thread+0x6a/0x520
   [<ffffffff8109c7c4>] kthread+0xe4/0x100
   [<ffffffff81884c52>] ret_from_fork+0x22/0x40

This happens because we increment rx_pkts on -ENOMEM and -EIO, resulting
in rx_pkts > 0. Fix this by only bumping rx_pkts if we were actually
given a non-zero budget.
Signed-off-by: Calvin Owens <calvinowens@fb.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The clock-names for pclk was wrongly set to "core", but the bindings
specifies "pclk".
This was not cathed until the legacy non-documented bindings were removed.
Reported-by: Andreas Färber <afaerber@suse.de>
Fixes: f72d6f60 ("ARM64: dts: meson-gx: use stable UART bindings with correct gate clock")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>

Neal Cardwell says:

====================
TCP BBR sampling fixes for loss recovery undo

This patch series has a few minor bug fixes for cases where spurious
loss recoveries can trick BBR estimators into estimating that the
available bandwidth is much lower than the true available bandwidth.
In both cases the fix here is to just reset the estimator upon loss
recovery undo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix BBR so that upon notification of a loss recovery undo BBR resets
long-term bandwidth sampling.

Under high reordering, reordering events can be interpreted as loss.
If the reordering and spurious loss estimates are high enough, this
can cause BBR to spuriously estimate that we are seeing loss rates
high enough to trigger long-term bandwidth estimation. To avoid that
problem, this commit resets long-term bandwidth sampling on loss
recovery undo events.
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>