Only used locally. Found by sparse.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Silences the below warnings when building with ARM_LPAE enabled, which
gives longer dma_addr_t by default:

drivers/net/ethernet/ti/davinci_cpdma.c: In function 'cpdma_desc_pool_create':
drivers/net/ethernet/ti/davinci_cpdma.c:182:3: warning: passing argument 3 of 'dma_alloc_attrs' from incompatible pointer type [enabled by default]
drivers/net/ethernet/ti/davinci_cpdma.c: In function 'desc_phys':
drivers/net/ethernet/ti/davinci_cpdma.c:222:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/net/ethernet/ti/davinci_cpdma.c:223:8: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

Removed the shared ei_debug variable. Replaced it by adding u32 msg_enable to
the private struct ei_device. Now each 8390 ethernet instance has a per-device
logging variable.

Changed older style printk() calls to more canonical forms.

Tested on: ne, ne2k-pci, smc-ultra, and wd hardware.

V4.0
- Substituted pr_info() and pr_debug() for printk() KERN_INFO and KERN_DEBUG

V3.0
- Checked for cases where pr_cont() was most appropriate choice.
- Changed module parameter from 'debug' to 'msg_enable' because debug was
no longer the best description.

V2.0
- Changed netif_msg_(drv|probe|ifdown|rx_err|tx_err|tx_queued|intr|rx_status|hw)
to netif_(dbg|info|warn|err) where possible.
Signed-off-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 4191 states in 3.5:

   When a host avoids using any non-reachable router X and instead sends
   a data packet to another router Y, and the host would have used
   router X if router X were reachable, then the host SHOULD probe each
   such router X's reachability by sending a single Neighbor
   Solicitation to that router's address.  A host MUST NOT probe a
   router's reachability in the absence of useful traffic that the host
   would have sent to the router if it were reachable.  In any case,
   these probes MUST be rate-limited to no more than one per minute per
   router.

Currently, when the neighbour corresponding to a router falls into
NUD_FAILED, it's never considered again. Introduce a new rt6_nud_state
value, RT6_NUD_FAIL_PROBE, which suggests the route should not be used but
should be probed with a single NS. The probe is ratelimited by the existing
code. To better distinguish meanings of the failure values, rename
RT6_NUD_FAIL_SOFT to RT6_NUD_FAIL_DO_RR.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In sctp_err_lookup, goto out while the asoc is not NULL, so remove the
check NULL. Also, in sctp_err_finish which called by sctp_v4_err and
sctp_v6_err, they pass asoc to sctp_err_finish while the asoc is not
NULL, so remove the check.
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It already has a NULL pointer judgment of rtab in qdisc_put_rtab().
Remove the judgment outside of qdisc_put_rtab().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Help of this function says: "in_dev: only on this interface, 0=any interface",
but since commit 39a6d063 ("[NETNS]: Process inet_confirm_addr in the
correct namespace."), the code supposes that it will never be NULL. This
function is never called with in_dev == NULL, but it's exported and may be used
by an external module.

Because this patch restore the ability to call inet_confirm_addr() with in_dev
== NULL, I partially revert the above commit, as suggested by Julian.

CC: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

vxlan_group_used only allows device to leave multicast group
when the remote_ip of this vxlan device is difference from
other vxlan devices' remote_ip. this will cause device not
leave multicast group untile the vn_sock of this vxlan deivce
being released.

The check in vxlan_group_used is not quite precise. since even
the remote_ip is same, but these vxlan devices may use different
lower devices, and they may use different vn_socks.

Only when some vxlan devices use the same vn_sock,same lower
device and same remote_ip, the mc_list of the vn_sock should
not be changed.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In vxlan_open, vxlan_group_used always returns true,
because the state of the vxlan deivces which we want
to open has alreay been running. and it has already
in vxlan_list.

Since ip_mc_join_group takes care of the reference
of struct ip_mc_list. removing vxlan_group_used here
is safe.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Without this bgmac_adjust_link didn't know it should re-initialize MAC
state. This led to the MAC not working after if down & up routine.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SKIP_NONLOCAL hides the control flow. The control flow should be
inlined and expanded explicitly in code so that someone who reads
it can tell the control flow can be changed by the statement.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When adjusting the link speed, the target frequency is determined by a
'swith (LINK_SPEED)' statement, that assigns the target rate only for
valid and expected LINK_SPEED values. This incomplete switch statement
leads to the following build warning:
     drivers/net/ethernet/cadence/macb.c: In function 'macb_handle_link_change':
  >> drivers/net/ethernet/cadence/macb.c:241:14: warning: 'rate' may be used uninitialized in this function [-Wmaybe-uninitialized]
        netdev_warn(dev, "unable to generate target frequency: %ld Hz\n",
                   ^
     drivers/net/ethernet/cadence/macb.c:215:13: note: 'rate' was declared here
       long ferr, rate, rate_rounded;

Fixing this by bailing out of that function in the switch's default case
before the rate variable is used.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jon Maloy says:

====================
tipc: cleanups in media and bearer layer

This commit series performs a number cleanups in order to make the
bearer and media part of the code more comprehensible and manageable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

In early versions of TIPC it was possible to administratively block
individual links through the use of the member flag 'blocked'. This
functionality was deemed redundant, and since commit 7368dd ("tipc:
clean out all instances of #if 0'd unused code"), this flag has been
unused.

In the current code, a link only needs to be blocked for sending and
reception if it is subject to an ongoing link failover. In that case,
it is sufficient to check if the number of expected failover packets
is non-zero, something which is done via the funtion 'link_blocked()'.

This commit finally removes the redundant 'blocked' flag completely.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently TIPC supports two L2 media types, Ethernet and Infiniband.
Because both these media are accessed through the common net_device API,
several functions in the two media adaptation files turn out to be
fully or almost identical, leading to unnecessary code duplication.

In this commit we extract this common code from the two media files
and move them to the generic bearer.c. Additionally, we change
the function names to reflect their real role: to access L2 media,
irrespective of type.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, registering a TIPC stack handler in the network device layer
is done twice, once for Ethernet (eth_media) and Infiniband (ib_media)
repectively. But, as this registration is not media specific, we can
avoid some code duplication by moving the registering function to
the generic bearer layer, to the file bearer.c, and call it only once.
The same is true for the network device event notifier.

As a side effect, the two workqueues we are using for for setting up/
cleaning up media can now be eliminated. Furthermore, the array for
storing the specific media type structs, media_array[], can be entirely
deleted.

Note that the eth_started and ib_started flags were removed during the
code relocation.  There is now only one call to bearer_setup and
bearer_cleanup, and these can logically not race against each other.

Despite its size, this cleanup work incurs no functional changes in TIPC.
In particular, it should be noted that the sequence ordering of received
packets is unaffected by this change, since packet reception never was
subject to any work queue handling in the first place.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

TIPC is currently using the field 'af_packet_priv' in struct net_device
as a handle to find the bearer instance associated to the given network
device. But, by doing so it is blocking other networking cleanups, such
as the one discussed here:

http://patchwork.ozlabs.org/patch/178044/

This commit removes this usage from TIPC. Instead, we introduce a new
field, 'tipc_ptr', to the net_device structure, to serve this purpose.
When TIPC bearer is enabled, the bearer object is associated to
'tipc_ptr'. When a TIPC packet arrives in the recv_msg() upcall
from a networking device, the bearer object can now be obtained from
'tipc_ptr'. When a bearer is disabled, the bearer object is detached
from its underlying network device by setting 'tipc_ptr' to NULL.

Additionally, an RCU lock is used to protect the new pointer.
Henceforth, the existing tipc_net_lock is used in write mode to
serialize write accesses to this pointer, while the new RCU lock is
applied on the read side to ensure that the pointer is 100% valid
within its wrapped area for all readers.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

struct 'tipc_media' represents the specific info that the media
layer adaptors (eth_media and ib_media) expose to the generic
bearer layer. We clarify this by improved commenting, and by giving
the 'media_list' array the more appropriate name 'media_info_array'.

There are no functional changes in this commit.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Communication media types are abstracted through the struct 'tipc_media',
one per media type. These structs are allocated statically inside their
respective media file.

Furthermore, in order to be able to reach all instances from a central
location, we keep a static array with pointers to these structs. This
array is currently initialized at runtime, under protection of
tipc_net_lock. However, since the contents of the array itself never
changes after initialization, we can just as well initialize it at
compile time and make it 'const', at the same time making it obvious
that no lock protection is needed here.

This commit makes the array constant and removes the redundant lock
protection.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

sk_buff lists are currently relased by looping over the list and
explicitly releasing each buffer.

We replace all occurrences of this loop with a call to kfree_skb_list().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

From: Soren Brinkmann <soren.brinkmann@xilinx.com>

====================
net: macb updates

I'd really like to have Ethernet working for Zynq, so I want to at least
revive this discussion regarding this patchset. And the first four
patches should not even be too controversial.
I didn't change anything compared to my original RFC submission, except
for a typo in one of the commit messages.
Handling the tx_clk as optional clock input seems a little bit weird,
but it works on my Zynq platform and should be compatible with other
users of macb and their DT descriptions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Adjust the ethernet clock according to the negotiated link speed.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the device managed interface to request the IRQ, simplifying error
paths.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the device managed version of ioremap to remap IO memory,
simplifying error paths.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Migrate to using the device managed interface for clocks and clean up
the associated error paths.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Migrate the suspend/resume functions to use the dev_pm_ops PM interface.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Macros with multiple statements should be enclosed in a do - while loop
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spaces required around that '>' (ctx:VxV) and
before the open parenthesis '('.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"foo* bar" or "foo * bar" should be "foo *bar".
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Code indent should use tabs where possible
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

return is not a function, parentheses are not required.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>