Create a helper function to disable clocks and use it in remove(), too.
Now, clk_summary in debugfs reports the clocks as disabled and
unprepared after unbinding.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This provides enhanced_strobe mode feature support in sdhci-msm
driver.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

During tuning execution for HS400 mode, HW sequence recommends
to select MCLK_SEL/2(0x3) in VENDOR_SPEC & sdhc msm clock at GCC
to be 400MHZ (nearest supported clk). Add this change in tuning
sequence during HS400 tuning.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Clear SDHCI_HS400_TUNING flag after platform_execute_tuning
so that platform_execute_tuning may use it if needed.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Program CORE_CSR_CDC_DELAY_CFG for hardware recommended 1.25ns delay.
We may see data CRC errors if it's programmed for any other delay
value.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The vendor specific func register doesn't get reset when using the
software reset register. The various bootloader's could leave this
in an unknown state, hence reset this register to it's power on reset
value during probe.
Signed-off-by: Venkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Factor out sdhci_msm_hs400 used for DLL calibration in HS400
modes. This function will be needed for enhanced_strobe as well.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Factor out msm_set/get_clock_rate_for_bus_mode for it's later
use in changing the tuning sequence for selecting HS400
bus speed mode.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This factors out sdhci_msm_hc_select_mode to later use
it during enhanced_strobe mode select.
It also further breaks sdhci_msm_hc_select_mode
into separate functions for configuring HS400 mode
or other modes.
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Tested-by: Jeremy McNicoll <jeremymc@redhat.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch implements support for multiblock transfers bounded
by SET_BLOCK_COUNT (CMD23) on the MXS MMC host driver.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

host->dma_addr can store a value that is not returned by the DMA API,
so it is safer to check if is a valid DMA address indirectly.
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

With commit 67bf5156 ("gpio / ACPI: fix returned error from
acpi_dev_gpio_irq_get()"), mmc_gpiod_request_cd() returns -EPROBE_DEFER if
GPIO is not ready when sdhci-acpi driver is probed, and sdhci-acpi driver
should be probed again later in this case.

This fixes an order issue when both GPIO and sdhci-acpi drivers are built
as modules.

CC: stable@vger.kernel.org # v4.9
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=177101Tested-by: Jonas Aaberg <cja@gmx.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Using extern when declaring functions in the public header, core.h, is
redundant. Let's just remove the use of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

A significant amount of functions are available through the public mmc
host.h header file. Let's slim down this public mmc interface, as to
prevent users from abusing it, by moving some of the functions to private
mmc host.h header file.

This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

A significant amount of functions and other definitions are available
through the public mmc card.h header file. Let's slim down this public mmc
interface, as to prevent users from abusing it, by moving some of the
functions/definitions to private mmc header files.

This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

The mmc_card_present() function helps the mmc core to track an internal
state of the card device. More importantly, it's not intended to be used by
mmc host drivers to check for an inserted card. Therefore, let's stop using
it and instead rely on checking for a valid pointer to a struct mmc_card,
as it should be good enough.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

The mmc_card_present() function helps the mmc core to track an internal
state of the card device. More importantly, it's not intended to be used by
mmc host drivers to check for an inserted card. Therefore, let's stop using
it and instead rely on checking for a valid pointer to a struct mmc_card,
as it should be good enough.

Cc: linux-omap@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>

The struct _mmc_csd isn't being used and has been lurking around for a
while. Let's kill it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

As the public mmc.h header already contains similar defines for other mmc
commands and arguments, let's move those for erase/trim/discard into here
as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

Ideally the public mmc header file, core.h, shouldn't contain interfaces
particularly intended to be used by host drivers. Instead those should
remain in the host.h header file. Therefore, let's move a couple functions
from core.h to host.h.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

A significant amount of functions are available through the public mmc
core.h header file. Let's slim down this public mmc interface, as to
prevent users from abusing it, by moving some of the functions to private
mmc header files.

This change concentrates on moving the functions into private mmc headers,
following changes may continue with additional clean-ups, as an example
some functions can be turned into static.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

This is the first step in cleaning up the private mmc header files. In this
change we makes sure each header file builds standalone, as that helps to
resolve dependencies.

While changing this, it also seems reasonable to stop including other
headers from inside a header itself which it don't depend upon.
Additionally, in some cases such dependencies are better resolved by
forward declaring the needed struct.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

This is the first step in cleaning up the public mmc header files. In this
change we makes sure each header file builds standalone, as that helps to
resolve dependencies.

While changing this, it also seems reasonable to stop including other
headers from inside a header itself which it don't depend upon.
Additionally, in some cases such dependencies are better resolved by
forward declaring the needed struct.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>

I got this new build error on today's linux-next

drivers/mmc/host/s3cmci.h:69:24: error: field 'pio_tasklet' has incomplete type
  struct tasklet_struct pio_tasklet;
drivers/mmc/host/s3cmci.c: In function 's3cmci_enable_irq':
drivers/mmc/host/s3cmci.c:390:4: error: implicit declaration of function 'enable_irq';did you mean 'enable_imask'? [-Werror=implicit-function-declaration]

While I haven't found out why this happened now and not earlier, the
solution is obvious, we should include the header that defines
the structure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The MIPS Alchemy db1300 dev board depends on interrupt.h. Explicitly
include it instead of relying on the public mmc header host.h.

Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: <linux-mips@linux-mips.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>

The davinci board omapl138-hawk, depends on interrupt.h. Explicitly include
it instead of relying on the public mmc header host.h.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>

Some of the davinci boards, da850-evm, dm644x-evm and neuros-osd2 depends
on leds.h. Explicitly include it instead of relying on the public mmc
header host.h.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Sekhar Nori <nsekhar@ti.com>

Some of the pxa platforms, balloon3, colibri-pxa270-income, corgi,
trizeps4, vpac270, zeus and zylonite depends on leds.h. Explicitly include
it instead of relying on the public mmc header host.h.

Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: <linux-arm-kernel@lists.infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>

This patch fix some spelling typo found in devicetree/bindings/mmc.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

To validate whether native hotplug needs to be used, the tmio driver checks
whether the mmc->slot.cd_irq has been successfully assigned.

This check is redundant at its current place in tmio_mmc_host_probe(), as
the mmc core assigns mmc->slot.cd_irq a valid value first when
mmc_gpiod_request_cd_irq() is called. Therefore, let's just remove the
check for now, as that also removes a layering violation of the tmio driver
accessing core specific data via ->slot.cd_irq.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

The eSDHC_PRSSTAT[SDSTB] bit indicates whether the internal card clock is
stable. This bit is for the host driver to poll clock status when changing
the clock frequency. It is recommended to clear eSDHC_SYSCTL[SDCLKEN]
to remove glitch on the card clock when the frequency is changing. This
patch is to disable SDCLKEN bit before changing frequency and enable it
after SDSTB bit is set.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

This patch adds support for HS200 tuning mode on AMD eMMC-4.5.1
Reviewed-by: Sen, Pankaj <Pankaj.Sen@amd.com>
Reviewed-by: Shah, Nehal-bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reviewed-by: Agrawal, Nitesh-kumar <Nitesh-kumar.Agrawal@amd.com>
Signed-off-by: S-k, Shyam-sundar <Shyam-sundar.S-k@amd.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The mxcmmc platform data header depends on interrupt.h. Don't rely on the
public mmc header host.h to include it, bud instead make that dependency
explicit.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

It's unnecessary to check the irqs_queued value as
it always needs to queue one if irq isn't enabled.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Per SDIO Simplified Specification V3, section 3.1.2, A host that
supports UHS-I sets S18R to 1 in the argument of CMD5 to request a
change of the signal voltage to 1.8V. If the card supports UHS-I and
the current signal voltage is 3.3V, S18A is set to 1 in the R4 response.
If the signal voltage is already 1.8V, the card sets S18A to 0 so that
host maintains the current signal voltage. UHS-I is supported in SD mode
and S18A is always 0 in SPI mode.

For the current code, if the signaling voltage is fixed 1.8v, so
the card will set S18A to 0 for rocr and thus we would clear the
R4_18V_PRESENT from ocr, which make core won't try to use uhs mode.

To fix it, we expect sdio_read_cccr would fail if the uhs mode won't
work at all. Note that it's interesting that some sdio cards still
response S18A even the voltage is fixed to 1.8v and the CMD11 will
also accepted and finish enabling UHS mode successfully. I guess this
is why folks didn't notice this problem. Anyway, fix it.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Add new helper function, mmc_sdio_resend_if_cond, to be
reused when trying to retry the init sequence.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

* A multiplication for the size determination of a memory allocation
  indicated that an array data structure should be processed.
  Thus use the corresponding function "kmalloc_array".

  This issue was detected by using the Coccinelle software.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

* The script "checkpatch.pl" pointed information out like the following.

  WARNING: Prefer kcalloc over kzalloc with multiply

  Thus fix the affected source code place.

* Replace the specification of a data structure by a pointer dereference
  to make the corresponding size determination a bit safer according to
  the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

Replace the specification of a data structure by a pointer dereference
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>

The script "checkpatch.pl" pointed information out like the following.

WARNING: quoted string split across lines

Thus fix affected source code places.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>