- 26 Nov, 2016 12 commits
-
-
Azhar Shaikh authored
commit 274e43ed upstream. Commit 41a3da2b ("mfd: intel-lpss: Save register context on suspend") saved the register context while going to suspend and also put the device in reset state. Due to the resetting of device, system cannot enter S3/S0ix states when no_console_suspend flag is enabled. The system and serial console both hang. The resetting of device is not needed while going to suspend. Hence remove this code. Fixes: 41a3da2b ("mfd: intel-lpss: Save register context on suspend") Signed-off-by:
Azhar Shaikh <azhar.shaikh@intel.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Ira Weiny authored
commit 458ed666 upstream. The new s_rnr_timeout was not properly being set and the code was incorrectly setting a different timer. Found by code inspection. Fixes: 08279d5c ("staging/rdma/hfi1: use new RNR timer") Reviewed-by:
Mike Marciniszyn <mike.marciniszyn@intel.com> Signed-off-by:
Ira Weiny <ira.weiny@intel.com> Signed-off-by:
Dennis Dalessandro <dennis.dalessandro@intel.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Dennis Dalessandro authored
commit e1fafdcb upstream. The initial code for rdmavt carried with it a restriction that was a vestige from the qib driver, that to dma map a page it had to be less than a page size. This is not the case on modern hardware, both qib and hfi1 will be just fine with unaligned map requests. This fixes a 4.8 regression where by an IPoIB transfer of > PAGE_SIZE will hang because the dma map page call always fails. This was introduced after commit 5faba546 ("IB/ipoib: Report SG feature regardless of HW UD CSUM capability") added the capability to use SG by default. Rather than override this, the HW supports it, so allow SG. Reviewed-by:
-
Miklos Szeredi authored
commit 59c3b76c upstream. If pos is at the beginning of a page and copied is zero then page is not zeroed but is marked uptodate. Fix by skipping everything except unlock/put of page if zero bytes were copied. Reported-by:
Al Viro <viro@zeniv.linux.org.uk> Fixes: 6b12c1b3 ("fuse: Implement write_begin/write_end callbacks") Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
Thomas Gleixner authored
commit 7ee7e87d upstream. The type flags in the irq descriptor are there for historical reasons and only updated via irq_modify_status() or irq_set_type(). Both functions also update the type flags in irqdata. __setup_irq() is the only left over user of the type flags in the irq descriptor. If __setup_irq() is called with empty irq type flags, then the type flags are retrieved from irqdata. If an interrupt is shared, then the type flags are compared with the type flags stored in the irq descriptor. On x86 the ioapic does not have a irq_set_type() callback because the type is defined in the BIOS tables and cannot be changed. The type is stored in irqdata at setup time without updating the type data in the irq descriptor. As a result the comparison described above fails. There is no point in updating the irq descriptor flags because the only relevant storage is irqdata. Use the type flags from irqdata for both retrieval and comparison in __setup_irq() instead. Aside of that the print out in case of non matching type flags has the old and new type flags arguments flipped. Fix that as well. For correctness sake the flags stored in the irq descriptor should be removed, but this is beyond the scope of this bugfix and will be done in a later patch. Fixes: 4b357dae ("genirq: Look-up trigger type if not specified by caller") Reported-and-tested-by:
Thomas Gleixner <tglx@linutronix.de> Cc: Marc Zyngier <marc.zyngier@arm.com> Cc: Jon Hunter <jonathanh@nvidia.com> Link: http://lkml.kernel.org/r/alpine.DEB.2.20.1611072020360.3501@nanosSigned-off-by:
-
Steven Rostedt (Red Hat) authored
commit 546fece4 upstream. When a module is first loaded and its function ip records are added to the ftrace list of functions to modify, they are set to DISABLED, as their text is still in a read only state. When the module is fully loaded, and can be updated, the flag is cleared, and if their's any functions that should be tracing them, it is updated at that moment. But there's several locations that do record accounting and should ignore records that are marked as disabled, or they can cause issues. Alexei already fixed one location, but others need to be addressed. Fixes: b7ffffbb "ftrace: Add infrastructure for delayed enabling of module functions" Reported-by:
Alexei Starovoitov <ast@kernel.org> Signed-off-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Alexei Starovoitov authored
commit 977c1f9c upstream. ftrace_shutdown() checks for sanity of ftrace records and if dyn_ftrace->flags is not zero, it will warn. It can happen that 'flags' are set to FTRACE_FL_DISABLED at this point, since some module was loaded, but before ftrace_module_enable() cleared the flags for this module. In other words the module.c is doing: ftrace_module_init(mod); // calls ftrace_update_code() that sets flags=FTRACE_FL_DISABLED ... // here ftrace_shutdown() is called that warns, since err = prepare_coming_module(mod); // didn't have a chance to clear FTRACE_FL_DISABLED Fix it by ignoring disabled records. It's similar to what __ftrace_hash_rec_update() is already doing. Link: http://lkml.kernel.org/r/1478560460-3818619-1-git-send-email-ast@fb.com Fixes: b7ffffbb "ftrace: Add infrastructure for delayed enabling of module functions" Signed-off-by:
-
Wei Huang authored
commit b112c84a upstream. KVM calls kvm_pmu_set_counter_event_type() when PMCCFILTR is configured. But this function can't deals with PMCCFILTR correctly because the evtCount bits of PMCCFILTR, which is reserved 0, conflits with the SW_INCR event type of other PMXEVTYPER<n> registers. To fix it, when eventsel == 0, this function shouldn't return immediately; instead it needs to check further if select_idx is ARMV8_PMU_CYCLE_IDX. Another issue is that KVM shouldn't copy the eventsel bits of PMCCFILTER blindly to attr.config. Instead it ought to convert the request to the "cpu cycle" event type (i.e. 0x11). To support this patch and to prevent duplicated definitions, a limited set of ARMv8 perf event types were relocated from perf_event.c to asm/perf_event.h. Acked-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Wei Huang <wei@redhat.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Signed-off-by:
-
Wei Huang authored
commit 9e3f7a29 upstream. We're missing the handling code for the cycle counter accessed from a 32bit guest, leading to unexpected results. Signed-off-by:
-
Ignacio Alvarado authored
commit 1650b4eb upstream. Function user_notifier_unregister should be called only once for each registered user notifier. Function kvm_arch_hardware_disable can be executed from an IPI context which could cause a race condition with a VCPU returning to user mode and attempting to unregister the notifier. Signed-off-by:
Ignacio Alvarado <ikalvarado@google.com> Fixes: 18863bdd ("KVM: x86 shared msr infrastructure") Reviewed-by:
Paolo Bonzini <pbonzini@redhat.com> Signed-off-by:
Radim Krčmář <rkrcmar@redhat.com> Signed-off-by:
-
Paolo Bonzini authored
commit 7301d6ab upstream. Reported by syzkaller: [ INFO: suspicious RCU usage. ] 4.9.0-rc4+ #47 Not tainted ------------------------------- ./include/linux/kvm_host.h:536 suspicious rcu_dereference_check() usage! stack backtrace: CPU: 1 PID: 6679 Comm: syz-executor Not tainted 4.9.0-rc4+ #47 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 ffff880039e2f6d0 ffffffff81c2e46b ffff88003e3a5b40 0000000000000000 0000000000000001 ffffffff83215600 ffff880039e2f700 ffffffff81334ea9 ffffc9000730b000 0000000000000004 ffff88003c4f8420 ffff88003d3f8000 Call Trace: [< inline >] __dump_stack lib/dump_stack.c:15 [<ffffffff81c2e46b>] dump_stack+0xb3/0x118 lib/dump_stack.c:51 [<ffffffff81334ea9>] lockdep_rcu_suspicious+0x139/0x180 kernel/locking/lockdep.c:4445 [< inline >] __kvm_memslots include/linux/kvm_host.h:534 [< inline >] kvm_memslots include/linux/kvm_host.h:541 [<ffffffff8105d6ae>] kvm_gfn_to_hva_cache_init+0xa1e/0xce0 virt/kvm/kvm_main.c:1941 [<ffffffff8112685d>] kvm_lapic_set_vapic_addr+0xed/0x140 arch/x86/kvm/lapic.c:2217 Reported-by:
Dmitry Vyukov <dvyukov@google.com> Fixes: fda4e2e8 Cc: Andrew Honig <ahonig@google.com> Signed-off-by:
David Hildenbrand <david@redhat.com> Signed-off-by:
-
Yazen Ghannam authored
commit b0b6e868 upstream. cpu_llc_id (Last Level Cache ID) derivation on AMD Fam17h has an underflow bug when extracting the socket_id value. It starts from 0 so subtracting 1 from it will result in an invalid value. This breaks scheduling topology later on since the cpu_llc_id will be incorrect. For example, the the cpu_llc_id of the *other* CPU in the loops in set_cpu_sibling_map() underflows and we're generating the funniest thread_siblings masks and then when I run 8 threads of nbench, they get spread around the LLC domains in a very strange pattern which doesn't give you the normal scheduling spread one would expect for performance. Other things like EDAC use cpu_llc_id so they will be b0rked too. So, the APIC ID is preset in APICx020 for bits 3 and above: they contain the core complex, node and socket IDs. The LLC is at the core complex level so we can find a unique cpu_llc_id by right shifting the APICID by 3 because then the least significant bit will be the Core Complex ID. Tested-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
Yazen Ghannam <Yazen.Ghannam@amd.com> [ Cleaned up and extended the commit message. ] Signed-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
- 21 Nov, 2016 28 commits
-
-
Greg Kroah-Hartman authored
-
Michal Nazarewicz authored
commit a9e6f83c upstream. ffs_func_eps_disable is called from atomic context so it cannot sleep thus cannot grab a mutex. Change the handling of epfile->read_buffer to use non-sleeping synchronisation method. Reported-by:
Chen Yu <chenyu56@huawei.com> Signed-off-by:
Michał Nazarewicz <mina86@mina86.com> Fixes: 9353afbb ("buffer data from ‘oversized’ OUT requests") Tested-by:
John Stultz <john.stultz@linaro.org> Tested-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Michal Nazarewicz authored
commit 454915dd upstream. epfile->ep is protected by ffs->eps_lock (not epfile->mutex) so clear it while holding the spin lock. Tested-by:
-
David S. Miller authored
[ Upstream commit 0fd0ff01 ] Now that all of the user copy routines are converted to return accurate residual lengths when an exception occurs, we no longer need the broken fixup routines. Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 614da3d9 ] All of __ret{,l}_mone{_asi,_fp,_asi_fpu} are now unused. Signed-off-by:
-
David S. Miller authored
[ Upstream commit ee841d0a ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit e93704e4 ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 7ae3aaf5 ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 95707704 ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit cb736fdb ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit d0796b55 ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 0096ac9f ] Report the exact number of bytes which have not been successfully copied when an exception occurs, using the running remaining length. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 83a17d26 ] The fixup helper function mechanism for handling user copy fault handling is not %100 accurrate, and can never be made so. We are going to transition the code to return the running return return length, which is always kept track in one or more registers of each of these routines. In order to convert them one by one, we have to allow the existing behavior to continue functioning. Therefore make all the copy code that wants the fixup helper to be used return negative one. After all of the user copy routines have been converted, this logic and the fixup helpers themselves can be removed completely. Signed-off-by:
-
David S. Miller authored
[ Upstream commit aa95ce36 ] It is completely unused. Signed-off-by:
-
David S. Miller authored
[ Upstream commit a74ad5e6 ] When the vmalloc area gets fragmented, and because the firmware mapping area sits between where modules live and the vmalloc area, we can sometimes receive requests for enormous kernel TLB range flushes. When this happens the cpu just spins flushing billions of pages and this triggers the NMI watchdog and other problems. We took care of this on the TSB side by doing a linear scan of the table once we pass a certain threshold. Do something similar for the TLB flush, however we are limited by the TLB flush facilities provided by the different chip variants. First of all we use an (mostly arbitrary) cut-off of 256K which is about 32 pages. This can be tuned in the future. The huge range code path for each chip works as follows: 1) On spitfire we flush all non-locked TLB entries using diagnostic acceses. 2) On cheetah we use the "flush all" TLB flush. 3) On sun4v/hypervisor we do a TLB context flush on context 0, which unlike previous chips does not remove "permanent" or locked entries. We could probably do something better on spitfire, such as limiting the flush to kernel TLB entries or even doing range comparisons. However that probably isn't worth it since those chips are old and the TLB only had 64 entries. Reported-by:
James Clarke <jrtc27@jrtc27.com> Tested-by:
-
David S. Miller authored
[ Upstream commit a236441b ] Just like the non-cross-call TLB flush handlers, the cross-call ones need to avoid doing PC-relative branches outside of their code blocks. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 830cda3f ] Noticed by James Clarke. Signed-off-by:
-
David S. Miller authored
[ Upstream commit b429ae4d ] When we copy code over to patch another piece of code, we can only use PC-relative branches that target code within that piece of code. Such PC-relative branches cannot be made to external symbols because the patch moves the location of the code and thus modifies the relative address of external symbols. Use an absolute jmpl to fix this problem. Signed-off-by:
-
David S. Miller authored
[ Upstream commit 849c4987 ] If the number of pages we are flushing is more than twice the number of entries in the TSB, just scan the TSB table for matches rather than probing each and every page in the range. Based upon a patch and report by James Clarke. Signed-off-by:
-
James Clarke authored
[ Upstream commit 9d9fa230 ] Additionally, if the offset will overflow the immediate for a ba,pt instruction, fall back on a standard ba to get an extra 3 bits. Signed-off-by:
-
Baruch Siach authored
commit 8736f802 upstream. spidev.h uses _IOC_SIZEBITS directly. musl libc does not provide this macro unless linux/ioctl.h is included explicitly. Fixes build failures like: In file included from .../host/usr/arm-buildroot-linux-musleabihf/sysroot/usr/include/sys/ioctl.h:7:0, from .../build/spidev_test-v3.15/spidev_test.c:20: .../build/spidev_test-v3.15/spidev_test.c: In function ‘transfer’: .../build/spidev_test-v3.15/spidev_test.c:75:18: error: ‘_IOC_SIZEBITS’ undeclared (first use in this function) ret = ioctl(fd, SPI_IOC_MESSAGE(1), &tr); ^ Signed-off-by:
Baruch Siach <baruch@tkos.co.il> Signed-off-by:
Mark Brown <broonie@kernel.org> Cc: Ralph Sennhauser <ralph.sennhauser@gmail.com> Signed-off-by:
-
Florian Fainelli authored
[ Upstream commit c51e424d ] Commit 52f95bbf ("stmmac: fix adjust link call in case of a switch is attached") added some logic to avoid polling the fixed PHY and therefore invoking the adjust_link callback more than once, since this is a fixed PHY and link events won't be generated. This works fine the first time, because we start with phydev->irq = PHY_POLL, so we call adjust_link, then we set phydev->irq = PHY_IGNORE_INTERRUPT and we stop polling the PHY. Now, if we called ndo_close(), which calls both phy_stop() and does an explicit netif_carrier_off(), we end up with a link down. Upon calling ndo_open() again, despite starting the PHY state machine, we have PHY_IGNORE_INTERRUPT set, and we generate no link event at all, so the link is permanently down. Fixes: 52f95bbf ("stmmac: fix adjust link call in case of a switch is attached") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Acked-by:
Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
-
Xin Long authored
[ Upstream commit 5bf35ddf ] Now when users shutdown a sock with SEND_SHUTDOWN in sctp, even if this sock has no connection (assoc), sk state would be changed to SCTP_SS_CLOSING, which is not as we expect. Besides, after that if users try to listen on this sock, kernel could even panic when it dereference sctp_sk(sk)->bind_hash in sctp_inet_listen, as bind_hash is null when sock has no assoc. This patch is to move sk state change after checking sk assocs is not empty, and also merge these two if() conditions and reduce indent level. Fixes: d46e416c ("sctp: sctp should change socket state when shutdown is received") Reported-by:
Andrey Konovalov <andreyknvl@google.com> Tested-by:
Xin Long <lucien.xin@gmail.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Baoquan He authored
[ Upstream commit 6df77862 ] In-flight DMA from 1st kernel could continue going in kdump kernel. New io-page table has been created before bnx2 does reset at open stage. We have to wait for the in-flight DMA to complete to avoid it look up into the newly created io-page table at probe stage. Suggested-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
Baoquan He <bhe@redhat.com> Acked-by:
-
Baoquan He authored
[ Upstream commit 5d0d4b91 ] This reverts commit 3e1be7ad. When people build bnx2 driver into kernel, it will fail to detect and load firmware because firmware is contained in initramfs and initramfs has not been uncompressed yet during do_initcalls. So revert commit 3e1be7ad and work out a new way in the later patch. Signed-off-by:
Paul Menzel <pmenzel@molgen.mpg.de> Signed-off-by:
-
Arkadi Sharshevsky authored
[ Upstream commit 42cdb338 ] The device's neighbour table is periodically dumped in order to update the kernel about active neighbours. A single dump session may span multiple queries, until the response carries less records than requested or when a record (can contain up to four neighbour entries) is not full. Current code stops the session when the number of returned records is zero, which can result in infinite loop in case of high packet rate. Fix this by stopping the session according to the above logic. Fixes: c723c735 ("mlxsw: spectrum_router: Periodically update the kernel's neigh table") Signed-off-by:
Arkadi Sharshevsky <arkadis@mellanox.com> Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Yotam Gigi authored
[ Upstream commit 2d644d4c ] When binding port to a newly created span entry, its refcount is initialized to zero even though it has a bound port. That leads to unexpected behaviour when the user tries to delete that port from the span entry. Fix this by initializing the reference count to 1. Also add a warning to put function. Fixes: 763b4b70 ("mlxsw: spectrum: Add support in matchall mirror TC offloading") Signed-off-by:
Yotam Gigi <yotamg@mellanox.com> Reviewed-by:
-
Mike Frysinger authored
[ Upstream commit 7b5b74ef ] This reverts commit cf00713a ("include/uapi/linux/atm_zatm.h: include linux/time.h"). This attempted to fix userspace breakage that no longer existed when the patch was merged. Almost one year earlier, commit 70ba07b6 ("atm: remove 'struct zatm_t_hist'") deleted the struct in question. After this patch was merged, we now have to deal with people being unable to include this header in conjunction with standard C library headers like stdlib.h (which linux-atm does). Example breakage: x86_64-pc-linux-gnu-gcc -DHAVE_CONFIG_H -I. -I../.. -I./../q2931 -I./../saal \ -I. -DCPPFLAGS_TEST -I../../src/include -O2 -march=native -pipe -g \ -frecord-gcc-switches -freport-bug -Wimplicit-function-declaration \ -Wnonnull -Wstrict-aliasing -Wparentheses -Warray-bounds \ -Wfree-nonheap-object -Wreturn-local-addr -fno-strict-aliasing -Wall \ -Wshadow -Wpointer-arith -Wwrite-strings -Wstrict-prototypes -c zntune.c In file included from /usr/include/linux/atm_zatm.h:17:0, from zntune.c:17: /usr/include/linux/time.h:9:8: error: redefinition of ‘struct timespec’ struct timespec { ^ In file included from /usr/include/sys/select.h:43:0, from /usr/include/sys/types.h:219, from /usr/include/stdlib.h:314, from zntune.c:9: /usr/include/time.h:120:8: note: originally defined here struct timespec ^ Signed-off-by:
Mike Frysinger <vapier@gentoo.org> Acked-by:
Mikko Rapeli <mikko.rapeli@iki.fi> Signed-off-by:
-
