the tlv len is set to the total len of the wmi cmd, it will trigger
firmware crash, correct the tlv len.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1 and QCA6174
PCIE with firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.

Fixes: ce834e28 ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

It seems to be unused.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Do some cosmetic cleanup while reviewing the files. No functional changes.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

For RX, it has two parts, one is to read data from sdio, another
is to indicate the packets to upper stack. Recently it has only
one thread to do all RX things, it results that it is sequential
for RX and low throughout, change RX to parallel for the two parts
will increase throughout.

This patch move the indication to a workqueue, it results in
significant performance improvement on RX path.

Udp rx throughout is 200Mbps without this patch, and it arrives
400Mbps with this patch.

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The max bundle size support by firmware is 32, change it from 8 to 32
will help performance. This results in significant performance
improvement on RX path.

The real max rx bundle is decided in ath10k_htc_wait_target(),
it is the min value of HTC_HOST_MAX_MSG_PER_RX_BUNDLE and the value reported
from firmware. So this change shouldn't cause any regressions with other
hardware supported by ath10k.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The existing implementation of initiating multiple sdio transfers for
receive bundling is slowing down the receive speed. Combining the
transfers using a bundle method would be ideal.

The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.

Test result of different length of data:
data packet(byte)   cost time(us)   calculated rate(Mbps)
      256               28                73
      512               33               124
     1024               35               234
     1792               45               318
    14336              168               682
    28672              333               688
    57344              660               695

Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Unless we sleep for a while before transitioning the MSA memory to WLAN
the MPSS.AT.4.0.c2-01184-SDM845_GEN_PACK-1 firmware triggers a security
violation fairly reliably. Unforutnately recovering from this failure
always results in the entire system freezing.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This reverts commit 334f5b61.

This caused ath10k_snoc on Qualcomm MSM8998, SDM845 and QCS404 platforms to
trigger an assert in the firmware:

err_qdi.c:456:EF:wlan_process:1:cmnos_thread.c:3900:Asserted in wlan_vdev.c:_wlan_vdev_up:3219

Revert the offending commit for now.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Downloading ath10k firmware needs a large number of IOs and
cpuidle's miss predictions make it worse. In the worst case,
resume time can be three times longer than the average on sdio.

This patch disables cpuidle during firmware downloading by
applying PM_QOS_CPU_DMA_LATENCY in ath10k_download_fw().

Tested-on: QCA9880
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00029
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

STA number was not restored if OOM happened.

Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00018
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath10k does not provide transmit rate info per MSDU
in tx completion, mark that as -1 so mac80211
will ignore the rates. This fixes mac80211 update Mesh
link metric with invalid transmit rate info.

Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Hou Bao Hou <houbao@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

Driver could access a NULL firmware pointer if we don't
return here.

Fixes: 5195b904 ("rtw88: avoid FW info flood")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

This leak was found by testing the EDIMAX EW-7612 on Raspberry Pi 3B+ with
Linux 5.4-rc5 (multi_v7_defconfig + rtlwifi + kmemleak) and noticed a
single memory leak during probe:

unreferenced object 0xec13ee40 (size 176):
  comm "kworker/u8:1", pid 36, jiffies 4294939321 (age 5580.790s)
  hex dump (first 32 bytes):
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
    00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
  backtrace:
    [<fc1bbb3e>] __netdev_alloc_skb+0x9c/0x164
    [<863dfa6e>] rtl92c_set_fw_rsvdpagepkt+0x254/0x340 [rtl8192c_common]
    [<9572be0d>] rtl92cu_set_hw_reg+0xf48/0xfa4 [rtl8192cu]
    [<116df4d8>] rtl_op_bss_info_changed+0x234/0x96c [rtlwifi]
    [<8933575f>] ieee80211_bss_info_change_notify+0xb8/0x264 [mac80211]
    [<d4061e86>] ieee80211_assoc_success+0x934/0x1798 [mac80211]
    [<e55adb56>] ieee80211_rx_mgmt_assoc_resp+0x174/0x314 [mac80211]
    [<5974629e>] ieee80211_sta_rx_queued_mgmt+0x3f4/0x7f0 [mac80211]
    [<d91091c6>] ieee80211_iface_work+0x208/0x318 [mac80211]
    [<ac5fcae4>] process_one_work+0x22c/0x564
    [<f5e6d3b6>] worker_thread+0x44/0x5d8
    [<82c7b073>] kthread+0x150/0x154
    [<b43e1b7d>] ret_from_fork+0x14/0x2c
    [<794dff30>] 0x0

It is because 8192cu doesn't implement usb_cmd_send_packet(), and this
patch just frees the skb within the function to resolve memleak problem
by now. Since 8192cu doesn't turn on fwctrl_lps that needs to download
command packet for firmware via the function, applying this patch doesn't
affect driver behavior.
Reported-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

On 2019-10-28 06:07, wbob wrote:
> Hello Roman,
>
> while reading around drivers/net/wireless/ralink/rt2x00/rt2800lib.c
> I stumbled on what I think is an edit of yours made in error in march
> 2017:
>
> https://github.com/torvalds/linux/commit/41977e86#diff-dae5dc10da180f3b055809a48118e18aR5281
>
> RT6352 in line 5281 should not have been introduced as the "else if"
> below line 5291 can then not take effect for a RT6352 device. Another
> possibility is for line 5291 to be not for RT6352, but this seems
> very unlikely. Are you able to clarify still after this substantial time?
>
> 5277: static int rt2800_init_registers(struct rt2x00_dev *rt2x00dev)
> ...
> 5279:  } else if (rt2x00_rt(rt2x00dev, RT5390) ||
> 5280:         rt2x00_rt(rt2x00dev, RT5392) ||
> 5281:         rt2x00_rt(rt2x00dev, RT6352)) {
> ...
> 5291:  } else if (rt2x00_rt(rt2x00dev, RT6352)) {
> ...

Hence remove errornous line 5281 to make the driver actually
execute the correct initialization routine for MT7620 chips.

As it was requested by Stanislaw Gruszka remove setting values of
MIMO_PS_CFG and TX_PIN_CFG. MIMO_PS_CFG is responsible for MIMO
power-safe mode (which is disabled), hence we can drop setting it.
TX_PIN_CFG is set correctly in other functions, and as setting this
value breaks some devices, rather don't set it here during init, but
only modify it later on.

Fixes: 41977e86 ("rt2x00: add support for MT7620")
Reported-by: wbob <wbob@jify.de>
Reported-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:83:17: warning: 'rtl8225sez2_tx_power_cck' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:79:17: warning: 'rtl8225sez2_tx_power_cck_A' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:75:17: warning: 'rtl8225sez2_tx_power_cck_B' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:71:17: warning: 'rtl8225sez2_tx_power_cck_ch14' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:62:17: warning: 'rtl8225se_tx_power_ofdm' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:53:17: warning: 'rtl8225se_tx_power_cck_ch14' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:44:17: warning: 'rtl8225se_tx_power_cck' defined but not used [-Wunused-const-variable=]
drivers/net/wireless//realtek/rtl818x/rtl8180/rtl8225se.c:40:17: warning: 'rtl8225se_tx_gain_cck_ofdm' defined but not used [-Wunused-const-variable=]

They are never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:841:7: warning: variable free_pdu set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:30: warning: variable tx_rts_count set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:842:6: warning: variable tx_rts set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:843:7: warning: variable totlen set but not used [-Wunused-but-set-variable]

They are never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

The LPS threshold was set to 2, means driver will leave LPS
mode if there is more than 2 frames TX/RX for every 2 seconds.
This makes driver enter/leave LPS frequently even if we just
"ping -i1" to the others.

Apparently we do not want to leave LPS mode if there is only
some background traffics or web surfing. By experiment, set
this to 50 is a more reasonable value to lower the over all
power consumption.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

local variable "ret" is not used. hence it is safe to remove and
just return 0.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

local variable "rc" is not used. It is safe to remove and
There is only one caller of libipw_qos_convert_ac_to_parameters().
hence make it void
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

ath.git patches for 5.5. Major changes:

wil6210

* add SPDX license identifiers

Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 5.5

First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.

This pull request also has a trivial conflict, the report and example
resolution here:

https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au

Major changes:

rtw88

* add deep power save support

* add mac80211 software tx queue (wake_tx_queue) support

* enable hardware rate control

* add TX-AMSDU support

* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support

* add power tracking support

* add 802.11ac beamformee support

* add set_bitrate_mask support

* add phy_info debugfs to show Tx/Rx physical status

* add RFE type 3 support for 8822b

ath10k

* add support for hardware rfkill on devices where firmware supports it

rtl8xxxu

* add bluetooth co-existence support for single antenna

iwlwifi

* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature/cleanup patchset includes the following patches:

 - bump version strings, by Simon Wunderlich

 - Simplify batadv_v_ogm_aggr_list_free using skb_queue_purge,
   by Christophe Jaillet

 - Replace aggr_list_lock with lock free skb handlers,
   by Christophe Jaillet

 - explicitly mark fallthrough cases, by Sven Eckelmann

 - Drop lockdep.h include from soft-interface.c, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ThinkPad Thunderbolt 3 Dock Gen 2 is another docking station that uses
RTL8153 based USB ethernet.

The device supports macpassthru, but it failed to pass the test of -AD,
-BND and -BD. Simply bypass these tests since the device supports this
feature just fine.

Also the ACPI objects have some differences between Dell's and Lenovo's,
so make those ACPI infos no longer hardcoded.

BugLink: https://bugs.launchpad.net/bugs/1827961Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements reset_prepare and reset_done, which are used
for handling FLR.
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sudarsana Reddy Kalluru says:

====================
bnx2x/cnic: Enable Multi-Cos.

The patch series enables Multi-cos feature in the driver. This require
the use of new firmware 7.13.15.0.
Patch (1) adds driver changes to use new FW.
Patches (2) - (3) enables multi-cos functionality in bnx2x driver.
Patch (4) adds cnic driver change as required by new FW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The new FW has added extra validation for HSI version to
make FW backward compatible with older VF drivers. Hence
set fp_hsi_ver to Fast Path HSI version of the FW in use.
Signed-off-by: Manish Rangankar <mrangankar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

PF driver doesn't enable tx-switching for all cos queues/clients,
which causes packets drop from PF to VF. Fix this by enabling
tx-switching on all cos queues/clients.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FW version 7.13.15 addresses the issue in Multi-cos implementation.
This patch re-enables the Multi-Cos support in the driver.

Fixes: d1f0b5dc ("bnx2x: Disable multi-cos feature.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 97a27d6d6e8d "bnx2x: Add FW 7.13.15.0" added said .bin FW to
linux-firmware tree. This FW addresses few important issues in the earlier
FW release.
This patch incorporates FW 7.13.15.0 in the bnx2x driver.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pass a phy_interface_t to of_get_phy_mode(), by changing the type of
phy_mode in the device structure. This then requires that
zmii_attach() is also changes, since it takes a pointer to phy_mode.

Fixes: 0c65b2b9 ("net: of_get_phy_mode: Change API to solve int/unit warnings")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
net_sched: convert packet counters to 64bit

This small patch series add 64bit support for packet counts.

Fact that the counters were still 32bit has been quite painful.

tc -s -d qd sh dev eth0 | head -3
qdisc mq 1: root
 Sent 665706335338 bytes 6526520373 pkt (dropped 2441, overlimits 0 requeues 91)
 backlog 0b 0p requeues 91
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Now the kernel uses 64bit packet counters in scheduler layer,
we want to export these counters to user space.

Instead risking breaking user space by adding fields
to struct gnet_stats_basic, add a new TCA_STATS_PKT64.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

After this change, qdisc packet counter is no longer
a 32bit quantity. We still export 32bit values to user.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

gnet_stats_basic_packed was really meant to be private kernel structure.

If this proves to be a problem, we will have to rename the in-kernel
version.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
mv88e6xxx ATU occupancy as devlink resource

This patchset add generic support to DSA for devlink resources. The
Marvell switch Address Translation Unit occupancy is then exported as
a resource. In order to do this, the number of ATU entries is added to
the per switch info structure. Helpers are added, and then the
resource itself is then added.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The ATU can report how many entries it contains. It does this per bin,
there being 4 bins in total. Export the ATU as a devlink resource, and
provide a method the needed callback to get the resource occupancy.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When retrieving the ATU statistics, and ATU get next has to be
performed to trigger the ATU to collect the statistics. Export a
helper from global1_atu to perform this.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add helpers to set/get the ATU statistics register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

For each supported switch, add an entry to the info structure for the
number of MACs which can be stored in the ATU. This will later be used
to export the ATU as a devlink resource, and indicate its occupancy,
how full the ATU is.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>