Enable HS-USB device for the Lager board, defining the GPIO that the driver
should check when probing. Since this board doesn't have the OTG ID pin, we
assume that GP5_18 (USB0_PWEN) is an ID pin because it is 1 when the SW5 is
in position 2-3 (meaning USB function) and 0 in other positions.

Note that there will be pinctrl-related error messages if both internal PCI
and HS-USB drivers are enabled but they should be just ignored.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: added pin node and prop, moved device node, fixed summary, supplemented
changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the R8A7790 generic part of the HS-USB device node.
It is up to the board file to enable the device.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
[Sergei: fixed summary, added changelog]
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Since the PHY of USB3.0 and EHCI/OHCI ch2 are the same, the USB3.0
driver cannot use the phy driver when the EHCI/OHCI ch2 already used it:

phy phy-e6590100.usb-phy.3: phy init failed --> -16
xhci-hcd: probe of ee000000.usb failed with error -16

If so, we have to unbind the EHCI/OHCI ch2, and then we have to bind
the USB3.0 driver as the following:

  echo 0000:02:02.0 > /sys/bus/pci/drivers/ehci-pci/unbind
  echo 0000:02:01.0 > /sys/bus/pci/drivers/ohci-pci/unbind
  echo ee000000.usb > /sys/bus/platform/drivers/xhci-hcd/bind

Note that there will be pinctrl-related error messages if both
internal PCI and USB3.0 are enabled but they should be just ignored:

sh-pfc e6060000.pfc: pin GP_5_22 already requested by ee0d0000.pci; cannot claim for ee000000.usb
sh-pfc e6060000.pfc: pin-182 (ee000000.usb) status -22
ata1: SATA link down (SStatus 0 SControl 300)
sh-pfc e6060000.pfc: could not request pin 182 (GP_5_22) from group usb2  on device sh-pfc
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Initialise TMU device using DT when booting bockw
using DT-reference.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This describes all of the TMU hardware of the r8a7778.
Each node is disabled and may be enabled as necessary
by board DTS files.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

ch0 will be used for clock events and for periodic clock events,
ch1 will be used as clock source.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Yoshifumi Hosoya <yoshifumi.hosoya.wj@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The clocks property for the scifa2 device node referred to the scifa0
clock index instead of the scifa2 clock index.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

SCIF and SCIFA can be plexed onto the same wires on Lager board. The
datasheet also describes the wires as SCIFA. So, to make use of the
bigger FIFOs switch to SCIFA instead.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the PCI USB devices that are behind the PCI bridges, adding necessary
links to the USB PHY device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Describe the PCI USB devices that are behind the PCI bridges, adding necessary
links to the USB PHY device.

Based on the original work by Ben Dooks <ben.dooks@codethink.co.uk>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable USB PHY device for the Henninger board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable USB PHY device for the Koelsch board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the R8A7791 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Enable USB PHY device for the Lager board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Define the R8A7790 generic part of the USB PHY device node. It is up to the
board file to enable the device.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This clock drives the INTCA irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: devicetree@vger.kernel.org
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Renesas ARM Based SoC r8a73a4 DT Timers Updates for v3.19

* Initialise CMT1 timer using DT

Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The DU device is now instantiated from the device tree, remove the
corresponding platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The DU device is now instantiated from the device tree, remove the
corresponding platform device.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Specify the DU output topology, enable the DU device and configure the
related pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The Mitsubishi AA104XD12 panel is commonly used with the Marzen, Lager
and Koelsch boards. Create a .dtsi file that describe the panel and its
connection to the board.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: resolved minor conflict]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add the DU device with a disabled state. Boards that want to enable the
DU need to specify the output topology
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[horms+renesas@verge.net.au: resolved minor conflict]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

The information is already included in the COPYING file in the kernel
sources root directory, we don't want to modify all source files when
the FSF will move to a new address, and I'm tired of seeing the related
checkpatch.pl warnings.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

r8a73a4_add_dt_devices() no longer enables any devices
so remove it.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Initialise CMT1 device using DT when booting ape6evm
using DT-reference.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Rename r8a7790_register_cmt() as r8a73a4_register_cmt() to
reflect name of the SoC in use. The use of r8a7790 appears
to be due to historical sharing of code from that SoC.
Shared code is no longer used.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

This describes all of the CMT1 hardware of the r8a73a4.
The node is disabled and may be enabled as necessary by board DTS files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

Add a stdout-path property so that automatic console selection works
in the absence of a "console=" parameter on the kernel command line.

Note that we have to keep the "console=ttyS1,115200n81" parameter in
chosen/bootargs, else the console will use the default setting of 9600
baud.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>