When saving and restoring the floating point state over an EFI runtime
call ensure that we handle streaming mode, only handling FFR if we are not
in streaming mode and ensuring that we are in normal mode over the call
into runtime services.

We currently assume that ZA will not be modified by runtime services, the
specification is not yet finalised so this may need updating if that
changes.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-24-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

Both streaming mode and ZA may increase power consumption when they are
enabled and streaming mode makes many FPSIMD and SVE instructions undefined
which will cause problems for any kernel mode floating point so disable
both when we flush the CPU state. This covers both kernel_neon_begin() and
idle and after flushing the state a reload is always required anyway.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-23-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

The ZA array can be read and written with the NT_ARM_ZA.  Similarly to
our interface for the SVE vector registers the regset consists of a
header with information on the current vector length followed by an
optional register data payload, represented as for signals as a series
of horizontal vectors from 0 to VL/8 in the endianness independent
format used for vectors.

On get if ZA is enabled then register data will be provided, otherwise
it will be omitted.  On set if register data is provided then ZA is
enabled and initialized using the provided data, otherwise it is
disabled.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-22-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

The streaming mode SVE registers are represented using the same data
structures as for SVE but since the vector lengths supported and in use
may not be the same as SVE we represent them with a new type NT_ARM_SSVE.
Unfortunately we only have a single 16 bit reserved field available in
the header so there is no space to fit the current and maximum vector
length for both standard and streaming SVE mode without redefining the
structure in a way the creates a complicatd and fragile ABI. Since FFR
is not present in streaming mode it is read and written as zero.

Setting NT_ARM_SSVE registers will put the task into streaming mode,
similarly setting NT_ARM_SVE registers will exit it. Reads that do not
correspond to the current mode of the task will return the header with
no register data. For compatibility reasons on write setting no flag for
the register type will be interpreted as setting SVE registers, though
users can provide no register data as an alternative mechanism for doing
so.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-21-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

Implement support for ZA in signal handling in a very similar way to how
we implement support for SVE registers, using a signal context structure
with optional register state after it. Where present this register state
stores the ZA matrix as a series of horizontal vectors numbered from 0 to
VL/8 in the endinanness independent format used for vectors.

As with SVE we do not allow changes in the vector length during signal
return but we do allow ZA to be enabled or disabled.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-20-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

When in streaming mode we have the same set of SVE registers as we do in
regular SVE mode with the exception of FFR and the use of the SME vector
length. Provide signal handling for these registers by taking one of the
reserved words in the SVE signal context as a flags field and defining a
flag which is set for streaming mode. When the flag is set the vector
length is set to the streaming mode vector length and we save and
restore streaming mode data. We support entering or leaving streaming
mode based on the value of the flag but do not support changing the
vector length, this is not currently supported SVE signal handling.

We could instead allocate a separate record in the signal frame for the
streaming mode SVE context but this inflates the size of the maximal signal
frame required and adds complication when validating signal frames from
userspace, especially given the current structure of the code.

Any implementation of support for streaming mode vectors in signals will
have some potential for causing issues for applications that attempt to
handle SVE vectors in signals, use streaming mode but do not understand
streaming mode in their signal handling code, it is hard to identify a
case that is clearly better than any other - they all have cases where
they could cause unexpected register corruption or faults.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-19-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

The ABI requires that streaming mode and ZA are disabled when invoking
signal handlers, do this in setup_return() when we prepare the task state
for the signal handler.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-18-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

By default all SME operations in userspace will trap.  When this happens
we allocate storage space for the SME register state, set up the SVE
registers and disable traps.  We do not need to initialize ZA since the
architecture guarantees that it will be zeroed when enabled and when we
trap ZA is disabled.

On syscall we exit streaming mode if we were previously in it and ensure
that all but the lower 128 bits of the registers are zeroed while
preserving the state of ZA. This follows the aarch64 PCS for SME, ZA
state is preserved over a function call and streaming mode is exited.
Since the traps for SME do not distinguish between streaming mode SVE
and ZA usage if ZA is in use rather than reenabling traps we instead
zero the parts of the SVE registers not shared with FPSIMD and leave SME
enabled, this simplifies handling SME traps. If ZA is not in use then we
reenable SME traps and fall through to normal handling of SVE.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-17-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

Allocate space for storing ZA on first access to SME and use that to save
and restore ZA state when context switching. We do this by using the vector
form of the LDR and STR ZA instructions, these do not require streaming
mode and have implementation recommendations that they avoid contention
issues in shared SMCU implementations.

Since ZA is architecturally guaranteed to be zeroed when enabled we do not
need to explicitly zero ZA, either we will be restoring from a saved copy
or trapping on first use of SME so we know that ZA must be disabled.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-16-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

When in streaming mode we need to save and restore the streaming mode
SVE register state rather than the regular SVE register state. This uses
the streaming mode vector length and omits FFR but is otherwise identical,
if TIF_SVE is enabled when we are in streaming mode then streaming mode
takes precedence.

This does not handle use of streaming SVE state with KVM, ptrace or
signals. This will be updated in further patches.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-15-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

In SME the use of both streaming SVE mode and ZA are tracked through
PSTATE.SM and PSTATE.ZA, visible through the system register SVCR.  In
order to context switch the floating point state for SME we need to
context switch the contents of this register as part of context
switching the floating point state.

Since changing the vector length exits streaming SVE mode and disables
ZA we also make sure we update SVCR appropriately when setting vector
length, and similarly ensure that new threads have streaming SVE mode
and ZA disabled.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-14-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

The Scalable Matrix Extension introduces support for a new thread specific
data register TPIDR2 intended for use by libc. The kernel must save the
value of TPIDR2 on context switch and should ensure that all new threads
start off with a default value of 0. Add a field to the thread_struct to
store TPIDR2 and context switch it with the other thread specific data.

In case there are future extensions which also use TPIDR2 we introduce
system_supports_tpidr2() and use that rather than system_supports_sme()
for TPIDR2 handling.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-13-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

As for SVE provide a prctl() interface which allows processes to
configure their SME vector length.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-12-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

As for SVE provide a sysctl which allows the default SME vector length to
be configured.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-11-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

The vector lengths used for SME are controlled through a similar set of
registers to those for SVE and enumerated using a similar algorithm with
some slight differences due to the fact that unlike SVE there are no
restrictions on which combinations of vector lengths can be supported
nor any mandatory vector lengths which must be implemented.  Add a new
vector type and implement support for enumerating it.

One slightly awkward feature is that we need to read the current vector
length using a different instruction (or enter streaming mode which
would have the same issue and be higher cost).  Rather than add an ops
structure we add special cases directly in the otherwise generic
vec_probe_vqs() function, this is a bit inelegant but it's the only
place where this is an issue.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-10-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

This patch introduces basic cpufeature support for discovering the presence
of the Scalable Matrix Extension.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-9-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

SME requires similar setup to that for SVE: disable traps to EL2 and
make sure that the maximum vector length is available to EL1, for SME we
have two traps - one for SME itself and one for TPIDR2.

In addition since we currently make no active use of priority control
for SCMUs we map all SME priorities lower ELs may configure to 0, the
architecture specified minimum priority, to ensure that nothing we
manage is able to configure itself to consume excessive resources.  This
will need to be revisited should there be a need to manage SME
priorities at runtime.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-8-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

As with SVE rather than impose ambitious toolchain requirements for SME
we manually encode the few instructions which we require in order to
perform the work the kernel needs to do. The instructions used to save
and restore context are provided as assembler macros while those for
entering and leaving streaming mode are done in asm volatile blocks
since they are expected to be used from C.

We could do the SMSTART and SMSTOP operations with read/modify/write
cycles on SVCR but using the aliases provided for individual field
accesses should be slightly faster. These instructions are aliases for
MSR but since our minimum toolchain requirements are old enough to mean
that we can't use the sX_X_cX_cX_X form and they always use xzr rather
than taking a value like write_sysreg_s() wants we just use .inst.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-7-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

The arm64 Scalable Matrix Extension (SME) adds some new system registers,
fields in existing system registers and exception syndromes. This patch
adds definitions for these for use in future patches implementing support
for this extension.

Since SME will be the first user of FEAT_HCX in the kernel also include
the definitions for enumerating it and the HCRX system register it adds.
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-6-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

Provide ABI documentation for SME similar to that for SVE. Due to the very
large overlap around streaming SVE mode in both implementation and
interfaces documentation for streaming mode SVE is added to the SVE
document rather than the SME one.
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Szabolcs Nagy <szabolcs.nagy@arm.com>
Link: https://lore.kernel.org/r/20220419112247.711548-5-broonie@kernel.orgSigned-off-by: Catalin Marinas <catalin.marinas@arm.com>

Pull xen fixlet from Juergen Gross:
 "A single cleanup patch for the Xen balloon driver"

* tag 'for-linus-5.18-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/balloon: don't use PV mode extra memory for zone device allocations

Pull x86 fixes from Thomas Gleixner:
 "Two x86 fixes related to TSX:

   - Use either MSR_TSX_FORCE_ABORT or MSR_IA32_TSX_CTRL to disable TSX
     to cover all CPUs which allow to disable it.

   - Disable TSX development mode at boot so that a microcode update
     which provides TSX development mode does not suddenly make the
     system vulnerable to TSX Asynchronous Abort"

* tag 'x86-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/tsx: Disable TSX development mode at boot
  x86/tsx: Use MSR_TSX_CTRL to clear CPUID bits

Pull timer fixes from Thomas Gleixner:
 "A small set of fixes for the timers core:

   - Fix the warning condition in __run_timers() which does not take
     into account that a CPU base (especially the deferrable base) never
     has a timer armed on it and therefore the next_expiry value can
     become stale.

   - Replace a WARN_ON() in the NOHZ code with a WARN_ON_ONCE() to
     prevent endless spam in dmesg.

   - Remove the double star from a comment which is not meant to be in
     kernel-doc format"

* tag 'timers-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick/sched: Fix non-kernel-doc comment
  tick/nohz: Use WARN_ON_ONCE() to prevent console saturation
  timers: Fix warning condition in __run_timers()

Pull SMP fixes from Thomas Gleixner:
 "Two fixes for the SMP core:

   - Make the warning condition in flush_smp_call_function_queue()
     correct, which checked a just emptied list head for being empty
     instead of validating that there was no pending entry on the
     offlined CPU at all.

   - The @cpu member of struct cpuhp_cpu_state is initialized when the
     CPU hotplug thread for the upcoming CPU is created. That's too late
     because the creation of the thread can fail and then the following
     rollback operates on CPU0. Get rid of the CPU member and hand the
     CPU number to the involved functions directly"

* tag 'smp-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  cpu/hotplug: Remove the 'cpu' member of cpuhp_cpu_state
  smp: Fix offline cpu check in flush_smp_call_function_queue()

Pull irq fix from Thomas Gleixner:
 "A single fix for the interrupt affinity spreading logic to take into
  account that there can be an imbalance between present and possible
  CPUs, which causes already assigned bits to be overwritten"

* tag 'irq-urgent-2022-04-17' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  genirq/affinity: Consider that CPUs on nodes can be unbalanced

Pull power supply fixes from Sebastian Reichel:

 - Fix a regression with battery data failing to load from DT

* tag 'for-v5.18-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
  power: supply: Reset err after not finding static battery
  power: supply: samsung-sdi-battery: Add missing charge restart voltages

Pull i2c fixes from Wolfram Sang:
 "Regular set of fixes for drivers and the dev-interface"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: ismt: Fix undefined behavior due to shift overflowing the constant
  i2c: dev: Force case user pointers in compat_i2cdev_ioctl()
  i2c: dev: check return value when calling dev_set_name()
  i2c: qcom-geni: Use dev_err_probe() for GPI DMA error
  i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit
  i2c: pasemi: Wait for write xfers to finish

Pull devicetree fixes from Rob Herring:

 - Fix scalar property schemas with array constraints

 - Fix 'enum' lists with duplicate entries

 - Fix incomplete if/then/else schemas

 - Add Renesas RZ/V2L SoC support to Mali Bifrost binding

 - Maintainers update for Marvell irqchip

* tag 'devicetree-fixes-for-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
  dt-bindings: display: panel-timing: Define a single type for properties
  dt-bindings: Fix array constraints on scalar properties
  dt-bindings: gpu: mali-bifrost: Document RZ/V2L SoC
  dt-bindings: net: snps: remove duplicate name
  dt-bindings: Fix 'enum' lists with duplicate entries
  dt-bindings: irqchip: mrvl,intc: refresh maintainers
  dt-bindings: Fix incomplete if/then/else schemas
  dt-bindings: power: renesas,apmu: Fix cpus property limits
  dt-bindings: extcon: maxim,max77843: fix ports type

Pull gpio fixes from Bartosz Golaszewski:
 "A single fix for gpio-sim and two patches for GPIO ACPI pulled from
  Andy:

   - fix the set/get_multiple() callbacks in gpio-sim

   - use correct format characters in gpiolib-acpi

   - use an unsigned type for pins in gpiolib-acpi"

* tag 'gpio-fixes-for-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
  gpio: sim: fix setting and getting multiple lines
  gpiolib: acpi: Convert type for pin to be unsigned
  gpiolib: acpi: use correct format characters

Pull ARM SoC fixes from Arnd Bergmann:
 "There are a number of SoC bugfixes that came in since the merge
  window, and more of them are already pending.

  This batch includes:

   - A boot time regression fix for davinci that triggered on
     multi_v5_defconfig when booting any platform

   - Defconfig updates to address removed features, changed symbol names
     or dependencies, for gemini, ux500, and pxa

   - Email address changes for Krzysztof Kozlowski

   - Build warning fixes for ep93xx and iop32x

   - Devicetree warning fixes across many platforms

   - Minor bugfixes for the reset controller, memory controller and SCMI
     firmware subsystems plus the versatile-express board"

* tag 'soc-fixes-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (34 commits)
  ARM: config: Update Gemini defconfig
  arm64: dts: qcom/sdm845-shift-axolotl: Fix boolean properties with values
  ARM: dts: align SPI NOR node name with dtschema
  ARM: dts: Fix more boolean properties with values
  arm/arm64: dts: qcom: Fix boolean properties with values
  arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
  arm: dts: imx: Fix boolean properties with values
  arm64: dts: tegra: Fix boolean properties with values
  arm: dts: at91: Fix boolean properties with values
  arm: configs: imote2: Drop defconfig as board support dropped.
  ep93xx: clock: Don't use plain integer as NULL pointer
  ep93xx: clock: Fix UAF in ep93xx_clk_register_gate()
  ARM: vexpress/spc: Fix all the kernel-doc build warnings
  ARM: vexpress/spc: Fix kernel-doc build warning for ve_spc_cpu_in_wfi
  ARM: config: u8500: Re-enable AB8500 battery charging
  ARM: config: u8500: Add some common hardware
  memory: fsl_ifc: populate child nodes of buses and mfd devices
  ARM: config: Refresh U8500 defconfig
  firmware: arm_scmi: Fix sparse warnings in OPTEE transport driver
  firmware: arm_scmi: Replace zero-length array with flexible-array member
  ...

Pull random number generator fixes from Jason Donenfeld:

 - Per your suggestion, random reads now won't fail if there's a page
   fault after some non-zero amount of data has been read, which makes
   the behavior consistent with all other reads in the kernel.

 - Rather than an inconsistent mix of random_get_entropy() returning an
   unsigned long or a cycles_t, now it just returns an unsigned long.

 - A memcpy() was replaced with an memmove(), because the addresses are
   sometimes overlapping. In practice the destination is always before
   the source, so not really an issue, but better to be correct than
   not.

* tag 'random-5.18-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
  random: use memmove instead of memcpy for remaining 32 bytes
  random: make random_get_entropy() return an unsigned long
  random: allow partial reads if later user copies fail

Pull SCSI fixes from James Bottomley:
 "13 fixes, all in drivers.

  The most extensive changes are in the iscsi series (affecting drivers
  qedi, cxgbi and bnx2i), the next most is scsi_debug, but that's just a
  simple revert and then minor updates to pm80xx"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: iscsi: MAINTAINERS: Add Mike Christie as co-maintainer
  scsi: qedi: Fix failed disconnect handling
  scsi: iscsi: Fix NOP handling during conn recovery
  scsi: iscsi: Merge suspend fields
  scsi: iscsi: Fix unbound endpoint error handling
  scsi: iscsi: Fix conn cleanup and stop race during iscsid restart
  scsi: iscsi: Fix endpoint reuse regression
  scsi: iscsi: Release endpoint ID when its freed
  scsi: iscsi: Fix offload conn cleanup when iscsid restarts
  scsi: iscsi: Move iscsi_ep_disconnect()
  scsi: pm80xx: Enable upper inbound, outbound queues
  scsi: pm80xx: Mask and unmask upper interrupt vectors 32-63
  Revert "scsi: scsi_debug: Address races following module load"

Merge tag 'intel-gpio-v5.18-2' of gitolite.kernel.org:pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-current

intel-gpio for v5.18-2

* Couple of fixes related to handling unsigned value of the pin from ACPI

gpiolib:
 -  acpi: Convert type for pin to be unsigned
 -  acpi: use correct format characters

Pull dma-mapping fix from Christoph Hellwig:

 - avoid a double memory copy for swiotlb (Chao Gao)

* tag 'dma-mapping-5.18-2' of git://git.infradead.org/users/hch/dma-mapping:
  dma-direct: avoid redundant memory sync for swiotlb

In order to immediately overwrite the old key on the stack, before
servicing a userspace request for bytes, we use the remaining 32 bytes
of block 0 as the key. This means moving indices 8,9,a,b,c,d,e,f ->
4,5,6,7,8,9,a,b. Since 4 < 8, for the kernel implementations of
memcpy(), this doesn't actually appear to be a problem in practice. But
relying on that characteristic seems a bit brittle. So let's change that
to a proper memmove(), which is the by-the-books way of handling
overlapping memory copies.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>

Merge misc fixes from Andrew Morton:
 "14 patches.

  Subsystems affected by this patch series: MAINTAINERS, binfmt, and
  mm (tmpfs, secretmem, kasan, kfence, pagealloc, zram, compaction,
  hugetlb, vmalloc, and kmemleak)"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  mm: kmemleak: take a full lowmem check in kmemleak_*_phys()
  mm/vmalloc: fix spinning drain_vmap_work after reading from /proc/vmcore
  revert "fs/binfmt_elf: use PT_LOAD p_align values for static PIE"
  revert "fs/binfmt_elf: fix PT_LOAD p_align values for loaders"
  hugetlb: do not demote poisoned hugetlb pages
  mm: compaction: fix compiler warning when CONFIG_COMPACTION=n
  mm: fix unexpected zeroed page mapping with zram swap
  mm, page_alloc: fix build_zonerefs_node()
  mm, kfence: support kmem_dump_obj() for KFENCE objects
  kasan: fix hw tags enablement when KUNIT tests are disabled
  irq_work: use kasan_record_aux_stack_noalloc() record callstack
  mm/secretmem: fix panic when growing a memfd_secret
  tmpfs: fix regressions from wider use of ZERO_PAGE
  MAINTAINERS: Broadcom internal lists aren't maintainers

Merge tag 'for-5.18/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - Fix memory corruption in DM integrity target when tag_size is less
   than digest size.

 - Fix DM multipath's historical-service-time path selector to not use
   sched_clock() and ktime_get_ns(); only use ktime_get_ns().

 - Fix dm_io->orig_bio NULL pointer dereference in dm_zone_map_bio() due
   to 5.18 changes that overlooked DM zone's use of ->orig_bio

 - Fix for regression that broke the use of dm_accept_partial_bio() for
   "abnormal" IO (e.g. WRITE ZEROES) that does not need duplicate bios

 - Fix DM's issuing of empty flush bio so that it's size is 0.

* tag 'for-5.18/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm: fix bio length of empty flush
  dm: allow dm_accept_partial_bio() for dm_io without duplicate bios
  dm zone: fix NULL pointer dereference in dm_zone_map_bio
  dm mpath: only use ktime_get_ns() in historical selector
  dm integrity: fix memory corruption when tag_size is less than digest size

The kmemleak_*_phys() apis do not check the address for lowmem's min
boundary, while the caller may pass an address below lowmem, which will
trigger an oops:

  # echo scan > /sys/kernel/debug/kmemleak
  Unable to handle kernel paging request at virtual address ff5fffffffe00000
  Oops [#1]
  Modules linked in:
  CPU: 2 PID: 134 Comm: bash Not tainted 5.18.0-rc1-next-20220407 #33
  Hardware name: riscv-virtio,qemu (DT)
  epc : scan_block+0x74/0x15c
   ra : scan_block+0x72/0x15c
  epc : ffffffff801e5806 ra : ffffffff801e5804 sp : ff200000104abc30
   gp : ffffffff815cd4e8 tp : ff60000004cfa340 t0 : 0000000000000200
   t1 : 00aaaaaac23954cc t2 : 00000000000003ff s0 : ff200000104abc90
   s1 : ffffffff81b0ff28 a0 : 0000000000000000 a1 : ff5fffffffe01000
   a2 : ffffffff81b0ff28 a3 : 0000000000000002 a4 : 0000000000000001
   a5 : 0000000000000000 a6 : ff200000104abd7c a7 : 0000000000000005
   s2 : ff5fffffffe00ff9 s3 : ffffffff815cd998 s4 : ffffffff815d0e90
   s5 : ffffffff81b0ff28 s6 : 0000000000000020 s7 : ffffffff815d0eb0
   s8 : ffffffffffffffff s9 : ff5fffffffe00000 s10: ff5fffffffe01000
   s11: 0000000000000022 t3 : 00ffffffaa17db4c t4 : 000000000000000f
   t5 : 0000000000000001 t6 : 0000000000000000
  status: 0000000000000100 badaddr: ff5fffffffe00000 cause: 000000000000000d
    scan_gray_list+0x12e/0x1a6
    kmemleak_scan+0x2aa/0x57e
    kmemleak_write+0x32a/0x40c
    full_proxy_write+0x56/0x82
    vfs_write+0xa6/0x2a6
    ksys_write+0x6c/0xe2
    sys_write+0x22/0x2a
    ret_from_syscall+0x0/0x2

The callers may not quite know the actual address they pass(e.g. from
devicetree).  So the kmemleak_*_phys() apis should guarantee the address
they finally use is in lowmem range, so check the address for lowmem's
min boundary.

Link: https://lkml.kernel.org/r/20220413122925.33856-1-patrick.wang.shcn@gmail.comSigned-off-by: Patrick Wang <patrick.wang.shcn@gmail.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 3ee48b6a ("mm, x86: Saving vmcore with non-lazy freeing of
vmas") introduced set_iounmap_nonlazy(), which sets vmap_lazy_nr to
lazy_max_pages() + 1, ensuring that any future vunmaps() immediately
purge the vmap areas instead of doing it lazily.

Commit 690467c8 ("mm/vmalloc: Move draining areas out of caller
context") moved the purging from the vunmap() caller to a worker thread.
Unfortunately, set_iounmap_nonlazy() can cause the worker thread to spin
(possibly forever).  For example, consider the following scenario:

 1. Thread reads from /proc/vmcore. This eventually calls
    __copy_oldmem_page() -> set_iounmap_nonlazy(), which sets
    vmap_lazy_nr to lazy_max_pages() + 1.

 2. Then it calls free_vmap_area_noflush() (via iounmap()), which adds 2
    pages (one page plus the guard page) to the purge list and
    vmap_lazy_nr. vmap_lazy_nr is now lazy_max_pages() + 3, so the
    drain_vmap_work is scheduled.

 3. Thread returns from the kernel and is scheduled out.

 4. Worker thread is scheduled in and calls drain_vmap_area_work(). It
    frees the 2 pages on the purge list. vmap_lazy_nr is now
    lazy_max_pages() + 1.

 5. This is still over the threshold, so it tries to purge areas again,
    but doesn't find anything.

 6. Repeat 5.

If the system is running with only one CPU (which is typicial for kdump)
and preemption is disabled, then this will never make forward progress:
there aren't any more pages to purge, so it hangs.  If there is more
than one CPU or preemption is enabled, then the worker thread will spin
forever in the background.  (Note that if there were already pages to be
purged at the time that set_iounmap_nonlazy() was called, this bug is
avoided.)

This can be reproduced with anything that reads from /proc/vmcore
multiple times.  E.g., vmcore-dmesg /proc/vmcore.

It turns out that improvements to vmap() over the years have obsoleted
the need for this "optimization".  I benchmarked `dd if=/proc/vmcore
of=/dev/null` with 4k and 1M read sizes on a system with a 32GB vmcore.
The test was run on 5.17, 5.18-rc1 with a fix that avoided the hang, and
5.18-rc1 with set_iounmap_nonlazy() removed entirely:

    |5.17  |5.18+fix|5.18+removal
  4k|40.86s|  40.09s|      26.73s
  1M|24.47s|  23.98s|      21.84s

The removal was the fastest (by a wide margin with 4k reads).  This
patch removes set_iounmap_nonlazy().

Link: https://lkml.kernel.org/r/52f819991051f9b865e9ce25605509bfdbacadcd.1649277321.git.osandov@fb.com
Fixes: 690467c8  ("mm/vmalloc: Move draining areas out of caller context")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Acked-by: Chris Down <chris@chrisdown.name>
Reviewed-by: Uladzislau Rezki (Sony) <urezki@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Baoquan He <bhe@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>