Add option in plat_stmmacenet_data struct to enable VLAN Filter Fail
Queuing. This option allows packets that fail VLAN filter to be routed
to a specific Rx queue when Receive All is also set.

When this option is enabled:
- Enable VFFQ only when entering promiscuous mode, because Receive All
  will pass up all rx packets that failed address filtering (similar to
  promiscuous mode).
- VLAN-promiscuous mode is never entered to allow rx packet to fail VLAN
  filters and get routed to selected VFFQ Rx queue.
Reviewed-by: Voon Weifeng <weifeng.voon@intel.com>
Reviewed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Devlink regions for SJA1105 DSA driver

This series exposes the SJA1105 static config as a devlink region. This
can be used for debugging, for example with the sja1105_dump user space
program that I have derived from Andrew Lunn's mv88e6xxx_dump:

https://github.com/vladimiroltean/mv88e6xxx_dump/tree/sja1105

Changes in v2:
- Tear down devlink params on initialization failure.
- Add driver identification through devlink.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Return the driver name and ASIC ID so that generic user space
application are able to know they're looking at sja1105 devlink regions
when pretty-printing them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As explained in Documentation/networking/dsa/sja1105.rst, this switch
has a static config held in the driver's memory and re-uploaded from
time to time into the device (after any major change).

The format of this static config is in fact described in UM10944.pdf and
it contains all the switch's settings (it also contains device ID, table
CRCs, etc, just like in the manual). So it is a useful and universal
devlink region to expose to user space, for debugging purposes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We'll have more devlink code soon. Group it together in a separate
translation object.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jesse Brandeburg says:

====================
make drivers/net/ethernet W=1 clean

The Goal: move to W=1 being default for drivers/net/ethernet, and
then use automation to catch more code issues (warnings) being
introduced.
The status: Getting much closer but not quite done for all
architectures.

After applying the patches below, the drivers/net/ethernet
directory can be built as modules with W=1 with no warnings (so
far on x64_64 arch only!). As Jakub pointed out, there is much
more work to do to clean up C=1, but that will be another series
of changes.

This series removes 1,247 warnings and hopefully allows the
ethernet directory to move forward from here without more
warnings being added. There is only one objtool warning now.

This version drops one of the Intel patches, as I couldn't
reproduce the original issue to document the warning.

Some of these patches are already sent and tested on Intel Wired
Lan, but the rest of the series titled drivers/net/ethernet
affects other drivers. The changes are all pretty
straightforward.
====================
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Saeed Mahameed <saeed@kernel.org>

As part of the W=1 cleanups for ethernet, a million [*] driver
comments had to be cleaned up to get the W=1 compilation to
succeed. This change finally makes the drivers/net/ethernet tree
compile with W=1 set on the command line. NOTE: The kernel uses
kdoc style (see Documentation/process/kernel-doc.rst) when
documenting code, not doxygen or other styles.

After this patch the x86_64 build has no warnings from W=1, however
scripts/kernel-doc says there are 1545 more warnings in source files, that
I need to develop a script to fix in a followup patch.

The errors fixed here are all kdoc of a few classes, with a few outliers:
In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10:
drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=]
 1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff };
      |                  ^~~~~~~~~~~~~~
... repeats 4 times...
drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body]
 2084 |    RX_USED_ADD(page, i);
drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’:
drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
  603 |  u32 tbisr, tanar, tanlpar;
      |      ^~~~~
drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’:
drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
 1207 |  u32 cfg, tanar, tbicr;
      |           ^~~~~
drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
 1063 |   int data_size, yf_size;
      |                  ^~~~~~~

Normal kdoc fixes:
warning: Function parameter or member 'x' not described in 'y'
warning: Excess function parameter 'x' description in 'y'
warning: Cannot understand <string> on line <NNN> - I thought it was a doc line

[*] - ok it wasn't quite a million, but it felt like it.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

kernel-doc script as used by W=1, is confused by the macro
usage inside the header describing the efx_ptp_data struct.

drivers/net/ethernet/sfc/ptp.c:345: warning: Function parameter or member 'MC_CMD_PTP_IN_TRANSMIT_LENMAX' not described in 'efx_ptp_data'

After some discussion on the list, break this patch out to
a separate one, and fix the issue through a creative
macro declaration.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As part of the W=1 series for ethernet, these drivers were
discovered to be using kdoc style comments but were not actually
doing kdoc. The kernel uses kdoc style when documenting code, not
doxygen or other styles.

Fixed Warnings:
drivers/net/ethernet/amazon/ena/ena_com.c:613: warning: Function parameter or member 'ena_dev' not described in 'ena_com_set_llq'
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_b0.c:1540: warning: Cannot understand  * @brief Set VLAN filter table
drivers/net/ethernet/xilinx/ll_temac_main.c:114: warning: Function parameter or member 'lp' not described in 'temac_indirect_busywait'
drivers/net/ethernet/xilinx/ll_temac_main.c:129: warning: Function parameter or member 'lp' not described in 'temac_indirect_in32'
drivers/net/ethernet/xilinx/ll_temac_main.c:129: warning: Function parameter or member 'reg' not described in 'temac_indirect_in32'
drivers/net/ethernet/xilinx/ll_temac_main.c:147: warning: Function parameter or member 'lp' not described in 'temac_indirect_in32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:147: warning: Function parameter or member 'reg' not described in 'temac_indirect_in32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'lp' not described in 'temac_indirect_out32'
drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'reg' not described in 'temac_indirect_out32'
drivers/net/ethernet/xilinx/ll_temac_main.c:172: warning: Function parameter or member 'value' not described in 'temac_indirect_out32'
drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'lp' not described in 'temac_indirect_out32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'reg' not described in 'temac_indirect_out32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:188: warning: Function parameter or member 'value' not described in 'temac_indirect_out32_locked'
drivers/net/ethernet/xilinx/ll_temac_main.c:212: warning: Function parameter or member 'lp' not described in 'temac_dma_in32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:212: warning: Function parameter or member 'reg' not described in 'temac_dma_in32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'lp' not described in 'temac_dma_out32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'reg' not described in 'temac_dma_out32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:228: warning: Function parameter or member 'value' not described in 'temac_dma_out32_be'
drivers/net/ethernet/xilinx/ll_temac_main.c:247: warning: Function parameter or member 'lp' not described in 'temac_dma_dcr_in'
drivers/net/ethernet/xilinx/ll_temac_main.c:247: warning: Function parameter or member 'reg' not described in 'temac_dma_dcr_in'
drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'lp' not described in 'temac_dma_dcr_out'
drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'reg' not described in 'temac_dma_dcr_out'
drivers/net/ethernet/xilinx/ll_temac_main.c:255: warning: Function parameter or member 'value' not described in 'temac_dma_dcr_out'
drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'lp' not described in 'temac_dcr_setup'
drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'op' not described in 'temac_dcr_setup'
drivers/net/ethernet/xilinx/ll_temac_main.c:265: warning: Function parameter or member 'np' not described in 'temac_dcr_setup'
drivers/net/ethernet/xilinx/ll_temac_main.c:300: warning: Function parameter or member 'ndev' not described in 'temac_dma_bd_release'
drivers/net/ethernet/xilinx/ll_temac_main.c:330: warning: Function parameter or member 'ndev' not described in 'temac_dma_bd_init'
drivers/net/ethernet/xilinx/ll_temac_main.c:600: warning: Function parameter or member 'ndev' not described in 'temac_setoptions'
drivers/net/ethernet/xilinx/ll_temac_main.c:600: warning: Function parameter or member 'options' not described in 'temac_setoptions'
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A couple of drivers had a "generic documentation" section that
would trigger a "can't understand" message from W=1 compiles.

Fix by using correct DOC: tags in the generic sections.

Fixed Warnings:
drivers/net/ethernet/arc/emac_arc.c:4: info: Scanning doc for c
drivers/net/ethernet/cadence/macb_pci.c:3: warning: missing initial short description on line:
 * Cadence GEM PCI wrapper.
drivers/net/ethernet/cadence/macb_pci.c:3: info: Scanning doc for Cadence
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While fixing the W=1 builds, this warning came up because the
developers used a very tricky way to get structures initialized
to a non-zero value, but this causes GCC to warn about an
override. In this case the override was intentional, so just
disable the warning for this code with a kernel macro that results
in disabling the warning for compiles on GCC versions after 8.

It is not appropriate to change the struct to initialize all the
values as it will just add a lot more code for no value. The code
is completely correct as is, we just want to acknowledge that
this code could generate a warning and we're ok with that.

NOTE: the __diag_ignore macro currently only accepts a second
argument of 8 (version 80000), it's either use this one or
open code the pragma.

Fixed Warnings example (all the same):
drivers/net/ethernet/renesas/sh_eth.c:51:12: warning: initialized field overwritten [-Woverride-init]
drivers/net/ethernet/renesas/sh_eth.c:52:12: warning: initialized field overwritten [-Woverride-init]
drivers/net/ethernet/renesas/sh_eth.c:53:13: warning: initialized field overwritten [-Woverride-init]
+ 256 more...
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The W=1 builds showed a few files exporting functions
(non-static) that were not prototyped. What actually happened is
that there were prototypes, but the include file was forgotten in
the implementation file.

Add the include file and remove the warnings.

Fixed Warnings:
drivers/net/ethernet/cavium/liquidio/cn68xx_device.c:124:5: warning: no previous prototype for ‘lio_setup_cn68xx_octeon_device’ [-Wmissing-prototypes]
drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:159:1: warning: no previous prototype for ‘octeon_pci_read_core_mem’ [-Wmissing-prototypes]
drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:168:1: warning: no previous prototype for ‘octeon_pci_write_core_mem’ [-Wmissing-prototypes]
drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:176:5: warning: no previous prototype for ‘octeon_read_device_mem64’ [-Wmissing-prototypes]
drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:185:5: warning: no previous prototype for ‘octeon_read_device_mem32’ [-Wmissing-prototypes]
drivers/net/ethernet/cavium/liquidio/octeon_mem_ops.c:194:6: warning: no previous prototype for ‘octeon_write_device_mem32’ [-Wmissing-prototypes]
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_dcb.c:453:6: warning: no previous prototype for ‘hclge_dcb_ops_set’ [-Wmissing-prototypes]
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As part of the W=1 compliation series, these lines all created
warnings about unused variables that were assigned a value. Most
of them are from register reads, but some are just picking up
a return value from a function and never doing anything with it.

Fixed warnings:
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
.../ethernet/cortina/gemini.c:2110:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/media.c:322:8: warning: variable ‘setup’ set but not used [-Wunused-but-set-variable]
.../ethernet/dec/tulip/de4x5.c:4928:13: warning: variable ‘r3’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6510:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/micrel/ksz884x.c:6087: warning: cannot understand function prototype: 'struct hw_regs '
.../ethernet/microchip/lan743x_main.c:161:6: warning: variable ‘int_en’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:1702:6: warning: variable ‘int_sts’ set but not used [-Wunused-but-set-variable]
.../ethernet/microchip/lan743x_main.c:3041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable]
.../ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable]
.../ethernet/marvell/mvneta.c:754:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:33:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:160:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:490:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable]
.../ethernet/neterion/vxge/vxge-traffic.c:2378:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable]
.../ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable]
.../ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/mellanox/mlx4/en_tx.c:858:6: warning: variable ‘ring_cons’ set but not used [-Wunused-but-set-variable]
.../ethernet/sis/sis900.c:792:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:878:11: warning: variable ‘rx_ev_pkt_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:23: warning: variable ‘rx_ev_mcast_pkt’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:877:7: warning: variable ‘rx_ev_hdr_type’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:876:7: warning: variable ‘rx_ev_other_err’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:1646:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable]
.../ethernet/sfc/falcon/farch.c:2535:32: warning: variable ‘spec’ set but not used [-Wunused-but-set-variable]
.../ethernet/via/via-velocity.c:880:6: warning: variable ‘curr_status’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/tlan.c:656:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/davinci_emac.c:1230:6: warning: variable ‘num_tx_pkts’ set but not used [-Wunused-but-set-variable]
.../ethernet/synopsys/dwc-xlgmac-common.c:516:8: warning: variable ‘str’ set but not used [-Wunused-but-set-variable]
.../ethernet/ti/cpsw_new.c:1662:22: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable]

The register reads should be OK, because the current
implementation of readl and friends will always execute even
without an lvalue.

When it makes sense, just remove the lvalue assignment and the
local. Other times, just remove the offending code, and
occasionally, just mark the variable as maybe unused since it
could be used in an ifdef or debug scenario.

Only compile tested with W=1.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove variables that were storing a return value from a register
read or other read, where the return value wasn't used. Those
conversions to remove the lvalue of the assignment should be safe
because the readl memory mapped reads are marked volatile and
should not be optimized out without an lvalue (I suspect a very
long time ago this wasn't guaranteed as it is today).

These changes are part of a separate patch to make it easier to review.

Warnings Fixed:
.../intel/e100.c:2596:9: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
.../intel/ixgb/ixgb_hw.c:101:6: warning: variable ‘icr_reg’ set but not used [-Wunused-but-set-variable]
.../intel/ixgb/ixgb_hw.c:277:6: warning: variable ‘ctrl_reg’ set but not used [-Wunused-but-set-variable]
.../intel/ixgb/ixgb_hw.c:952:15: warning: variable ‘temp_reg’ set but not used [-Wunused-but-set-variable]
.../intel/ixgb/ixgb_hw.c:1164:7: warning: variable ‘mdio_reg’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:132:6: warning: variable ‘ret_val’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:380:6: warning: variable ‘icr’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:2378:6: warning: variable ‘signal’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:2374:6: warning: variable ‘ctrl’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:2373:6: warning: variable ‘rxcw’ set but not used [-Wunused-but-set-variable]
.../intel/e1000/e1000_hw.c:4678:15: warning: variable ‘temp’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This takes care of all of the trivial W=1 fixes in the Intel
Ethernet drivers, which allows developers and maintainers to
build more of the networking tree with more complete warning
checks.

There are three classes of kdoc warnings fixed:
 - cannot understand function prototype: 'x'
 - Excess function parameter 'x' description in 'y'
 - Function parameter or member 'x' not described in 'y'

All of the changes were trivial comment updates on
function headers.

Inspired by Lee Jones' series of wireless work to do the same.
Compile tested only, and passes simple test of
$ git ls-files *.[ch] | egrep drivers/net/ethernet/intel | \
  xargs scripts/kernel-doc -none
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While we should always make sure that we specify a valid VLAN protocol
to vlan_proto_idx(), killing the machine when an invalid value is
specified is too harsh and not helpful for debugging. All callers are
capable of dealing with an error returned by vlan_proto_idx() so check
the index value and propagate it accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-2020-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for v5.10

Second set of patches for v5.10. Biggest change here is wcn3680
support to wcn36xx driver, otherwise smaller features. And naturally
the usual fixes and cleanups.

Major changes:

brcmfmac

* support 4-way handshake offloading for WPA/WPA2-PSK in AP mode

* support SAE authentication offload in AP mode

mt76

* mt7663 runtime power management improvements

* mt7915 A-MSDU offload

wcn36xx

* add support wcn3680 Wi-Fi 5 devices

ath11k

* spectral scan support for ipq6018
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

kbuild bot reported than link fails when CONFIG_ATH11K_DEBUGFS is disabled:

drivers/net/wireless/ath/ath11k/dp_rx.c:1662: undefined reference to `ath11k_debugfs_htt_ext_stats_handler'

This was because I had missed to move the static inline version of the function
(which are used when CONFIG_ATH11K_DEBUGFS is disabled) to debufs_htt_stats.h.
Also move ath11k_debugfs_htt_stats_req() at the same time. And create a stub
also for ath11k_debugfs_htt_stats_init() for consistency, even if it's not
needed.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 568f0603 ("ath11k: debugfs: move some function declarations to correct header files")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601024241-16594-1-git-send-email-kvalo@codeaurora.org

Huazhong Tan says:

====================
net: hns3: updates for -next

There are some updates for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

VF devices do not have speed division, its speed is depended on its PF.
So macro name of PCI device id of VF is incorrent to have 100G info, it
should be renamed by removing 100G info.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The 200G device has a new device id 0xA228, so adds this device id to
pci table, then the driver can probe it.

As speed_ability queried from firmware has only 8 bits and already be
used up, so firmware adds extra speed_ability_ext to indicate more
speed abilities to support 200G and driver needs to parse it.
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pf's interrupt resources will be changed with the number of
enabled pf. Dumping this resource information will be helpful
for debugging.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In hns3_process_hw_error(), the hardware error detection of the
ROCEE AXI RESP error type is added. When this error occurs,
the client needs to be notified of this error and take
corresponding operation.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If a variable is assigned a value before it is used, it's no
need to assign an initial value to the variable. So remove
these redundant operations.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove some unnecessary parameters of hclge_title_idx_print(),
and rename this function for readability.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit cfde141e ("mptcp: move option parsing into
mptcp_incoming_options()"), the 3rd function argument is no longer used.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Geliang Tang says:

====================
mptcp: RM_ADDR/ADD_ADDR enhancements

This series include two enhancements for the MPTCP path management,
namely RM_ADDR support and ADD_ADDR echo support, as specified by RFC
sections 3.4.1 and 3.4.2.

1 RM_ADDR support include 9 patches (1-3 and 8-13):

Patch 1 is the helper for patch 2, these two patches add the RM_ADDR
outgoing functions, which are derived from ADD_ADDR's corresponding
functions.

Patch 3 adds the RM_ADDR incoming logic, when RM_ADDR suboption is
received, close the subflow matching the rm_id, and update PM counter.

Patch 8 is the main remove routine. When the PM netlink removes an address,
we traverse all the existing msk sockets to find the relevant sockets. Then
trigger the RM_ADDR signal and remove the subflow which using this local
address, this subflow removing functions has been implemented in patch 9.

Finally, patches 10-13 are the self-tests for RM_ADDR.

2 ADD_ADDR echo support include 7 patches (4-7 and 14-16).

Patch 4 adds the ADD_ADDR echo logic, when the ADD_ADDR suboption has been
received, send out the same ADD_ADDR suboption with echo-flag, and no HMAC
included.

Patches 5 and 6 are the self-tests for ADD_ADDR echo. Patch 7 is a little
cleaning up.

Patch 14 and 15 are the helpers for patch 16. These three patches add
the ADD_ADDR retransmition when no ADD_ADDR echo is received.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implemented the retransmition of ADD_ADDR when no ADD_ADDR echo
is received. It added a timer with the announced address. When timeout
occurs, ADD_ADDR will be retransmitted.
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added a new helper sk_stop_timer_sync, it deactivates a timer
like sk_stop_timer, but waits for the handler to finish.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new struct mptcp_pm_add_entry to describe add_addr's entry.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added the remove addr and subflow test cases and two new
functions.

The first function run_remove_tests calls do_transfer with two new
arguments, rm_nr_ns1 and rm_nr_ns2, for the numbers of addresses should be
removed during the transfer process in namespace 1 and namespace 2.

If both these two arguments are 0, we do the join test cases with
"mptcp_connect -j" command. Otherwise, do the remove test cases with
"mptcp_connect -r" command.

The second function chk_rm_nr checks the RM_ADDR related mibs's counters.

The output of the test cases looks like this:

11 remove single subflow           syn[ ok ] - synack[ ok ] - ack[ ok ]
                                   rm [ ok ] - sf    [ ok ]
12 remove multiple subflows        syn[ ok ] - synack[ ok ] - ack[ ok ]
                                   rm [ ok ] - sf    [ ok ]
13 remove single address           syn[ ok ] - synack[ ok ] - ack[ ok ]
                                   add[ ok ] - echo  [ ok ]
                                   rm [ ok ] - sf    [ ok ]
14 remove subflow and signal       syn[ ok ] - synack[ ok ] - ack[ ok ]
                                   add[ ok ] - echo  [ ok ]
                                   rm [ ok ] - sf    [ ok ]
15 remove subflows and signal      syn[ ok ] - synack[ ok ] - ack[ ok ]
                                   add[ ok ] - echo  [ ok ]
                                   rm [ ok ] - sf    [ ok ]
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added a new cfg, named cfg_remove in mptcp_connect. This new
cfg_remove is copied from cfg_join. The only difference between them is in
the do_rnd_write function. Here we slow down the transfer process of all
data to let the RM_ADDR suboption can be sent and received completely.
Otherwise the remove address and subflow test cases don't work.
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added a new helper named mptcp_destroy_common containing the
shared code between mptcp_destroy() and mptcp_sock_destruct().
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added two new mibs for RM_ADDR, named MPTCP_MIB_RMADDR and
MPTCP_MIB_RMSUBFLOW, when the RM_ADDR suboption is received, increase
the first mib counter, when the local subflow is removed, increase the
second mib counter.
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implemented the local subflow removing function,
mptcp_pm_remove_subflow, it simply called mptcp_pm_nl_rm_subflow_received
under the PM spin lock.

We use mptcp_pm_remove_subflow to remove a local subflow, so change it's
argument from remote_id to local_id.

We check subflow->local_id in mptcp_pm_nl_rm_subflow_received to remove
a subflow.
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch implements the remove announced addr and subflow logic in PM
netlink.

When the PM netlink removes an address, we traverse all the existing msk
sockets to find the relevant sockets.

We add a new list named anno_list in mptcp_pm_data, to record all the
announced addrs. In the traversing, we check if it has been recorded.
If it has been, we trigger the RM_ADDR signal.

We also check if this address is in conn_list. If it is, we remove the
subflow which using this local address.

Since we call mptcp_pm_free_anno_list in mptcp_destroy, we need to move
__mptcp_init_sock before the mptcp_is_enabled check in mptcp_init_sock.
Suggested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The re-check of pm->accept_subflow with pm->lock held was missing, this
patch fixed it.
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added the ADD_ADDR related mibs counter check function
chk_add_nr(). This function check both ADD_ADDR and ADD_ADDR with
echo flag.

The output looks like this:

 07 unused signal address             syn[ ok ] - synack[ ok ] - ack[ ok ]
                                      add[ ok ] - echo  [ ok ]
 08 signal address                    syn[ ok ] - synack[ ok ] - ack[ ok ]
                                      add[ ok ] - echo  [ ok ]
 09 subflow and signal                syn[ ok ] - synack[ ok ] - ack[ ok ]
                                      add[ ok ] - echo  [ ok ]
 10 multiple subflows and signal      syn[ ok ] - synack[ ok ] - ack[ ok ]
                                      add[ ok ] - echo  [ ok ]
 11 remove subflow and signal         syn[ ok ] - synack[ ok ] - ack[ ok ]
                                      add[ ok ] - echo  [ ok ]
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added two mibs for ADD_ADDR, MPTCP_MIB_ADDADDR for receiving
of the ADD_ADDR suboption with echo-flag=0, and MPTCP_MIB_ECHOADD for
receiving the ADD_ADDR suboption with echo-flag=1.
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the ADD_ADDR suboption has been received, we need to send out the same
ADD_ADDR suboption with echo-flag=1, and no HMAC.
Suggested-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>