If a driver supports reading EEPROM but no EEPROM is installed in the system,
the driver's get_eeprom_len function returns 0. ethtool will subsequently
try to read that zero-length EEPROM anyway. If the driver does not support
EEPROM access at all, this operation will return -EOPNOTSUPP. If the driver
does support EEPROM access but no EEPROM is installed, the operation will
return -EINVAL. Return -EOPNOTSUPP in both cases for consistency.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 3b57de95 brought the support for a different amount of the
filter bins, but didn't update the PCI driver accordingly. This patch appends
the default values when the device is enumerated via PCI bus.

Fixes: 3b57de95 (net: stmmac: Support devicetree configs for mcast and ucast filter entries)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

With legacy booting, the platform init code was taking care of
the configuring of GPIOs. With device tree based booting, things
may or may not work depending what bootloader has configured or
if the legacy platform code gets called.

Let's add support for the pwrdn and reset GPIOs to the smc91x
driver to fix the issues of smc91x not working properly when
booted in device tree mode.

And let's change n900 to use these settings as some versions
of the bootloader do not configure things properly causing
errors.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kconfig already allows mpls to be built as module. Following patch
fixes Makefile to do same.

CC: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

mpls gso handler needs to pull skb after segmenting skb.

CC: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For Renesas USB 3.0 host controller, when unplugging the usb hub which
has the RTL8153 plugged, the driver would get -EPROTO for interrupt
transfer. There is high probability to get the information of "HC died;
cleaning up", if the driver continues to submit the interrupt transfer
before the disconnect() is called.

[ 1024.197678] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.213673] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.229668] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.245661] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.261653] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.277648] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.293642] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.309638] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.325633] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.341627] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.357621] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.373615] r8152 9-1.4:1.0 eth0: intr status -71
[ 1024.383097] usb 9-1: USB disconnect, device number 2
[ 1024.383103] usb 9-1.4: USB disconnect, device number 6
[ 1029.391010] xhci_hcd 0000:04:00.0: xHCI host not responding to stop endpoint command.
[ 1029.391016] xhci_hcd 0000:04:00.0: Assuming host is dying, halting host.
[ 1029.392551] xhci_hcd 0000:04:00.0: HC died; cleaning up
[ 1029.421480] usb 8-1: USB disconnect, device number 2
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
netfilter/ipvs fixes for net

The following patchset contains fixes for netfilter/ipvs. This round of
fixes is larger than usual at this stage, specifically because of the
nf_tables bridge reject fixes that I would like to see in 3.18. The
patches are:

1) Fix a null-pointer dereference that may occur when logging
   errors. This problem was introduced by 4a4739d5 ("ipvs: Pull
   out crosses_local_route_boundary logic") in v3.17-rc5.

2) Update hook mask in nft_reject_bridge so we can also filter out
   packets from there. This fixes 36d2af59 ("netfilter: nf_tables: allow
   to filter from prerouting and postrouting"), which needs this chunk
   to work.

3) Two patches to refactor common code to forge the IPv4 and IPv6
   reject packets from the bridge. These are required by the nf_tables
   reject bridge fix.

4) Fix nft_reject_bridge by avoiding the use of the IP stack to reject
   packets from the bridge. The idea is to forge the reject packets and
   inject them to the original port via br_deliver() which is now
   exported for that purpose.

5) Restrict nft_reject_bridge to bridge prerouting and input hooks.
   the original skbuff may cloned after prerouting when the bridge stack
   needs to flood it to several bridge ports, it is too late to reject
   the traffic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Restrict the reject expression to the prerouting and input bridge
hooks. If we allow this to be used from forward or any other later
bridge hook, if the frame is flooded to several ports, we'll end up
sending several reject packets, one per cloned packet.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

If the packet is received via the bridge stack, this cannot reject
packets from the IP stack.

This adds functions to build the reject packet and send it from the
bridge stack. Comments and assumptions on this patch:

1) Validate the IPv4 and IPv6 headers before further processing,
   given that the packet comes from the bridge stack, we cannot assume
   they are clean. Truncated packets are dropped, we follow similar
   approach in the existing iptables match/target extensions that need
   to inspect layer 4 headers that is not available. This also includes
   packets that are directed to multicast and broadcast ethernet
   addresses.

2) br_deliver() is exported to inject the reject packet via
   bridge localout -> postrouting. So the approach is similar to what
   we already do in the iptables reject target. The reject packet is
   sent to the bridge port from which we have received the original
   packet.

3) The reject packet is forged based on the original packet. The TTL
   is set based on sysctl_ip_default_ttl for IPv4 and per-net
   ipv6.devconf_all hoplimit for IPv6.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

That can be reused by the reject bridge expression to build the reject
packet. The new functions are:

* nf_reject_ip6_tcphdr_get(): to sanitize and to obtain the TCP header.
* nf_reject_ip6hdr_put(): to build the IPv6 header.
* nf_reject_ip6_tcphdr_put(): to build the TCP header.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

That can be reused by the reject bridge expression to build the reject
packet. The new functions are:

* nf_reject_ip_tcphdr_get(): to sanitize and to obtain the TCP header.
* nf_reject_iphdr_put(): to build the IPv4 header.
* nf_reject_ip_tcphdr_put(): to build the TCP header.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

Fixes: 36d2af59 ("netfilter: nf_tables: allow to filter from prerouting and postrouting")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>

These drivers now call ipv6_proxy_select_ident(), which is defined
only if CONFIG_INET is enabled.  However, they have really depended
on CONFIG_INET for as long as they have allowed sending GSO packets
from userland.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: f43798c2 ("tun: Allow GSO using virtio_net_hdr")
Fixes: b9fb9ee0 ("macvtap: add GSO/csum offload support")
Fixes: 5188cd44 ("drivers/net, ipv6: Select IPv6 fragment idents for virtio UFO packets")
Signed-off-by: David S. Miller <davem@davemloft.net>

Ben Hutchings says:

====================
drivers/net,ipv6: Fix IPv6 fragment ID selection for virtio

The virtio net protocol supports UFO but does not provide for passing a
fragment ID for fragmentation of IPv6 packets.  We used to generate a
fragment ID wherever such a packet was fragmented, but currently we
always use ID=0!

v2: Add blank lines after declarations
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

UFO is now disabled on all drivers that work with virtio net headers,
but userland may try to send UFO/IPv6 packets anyway.  Instead of
sending with ID=0, we should select identifiers on their behalf (as we
used to).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 916e4cf4 ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data")
Signed-off-by: David S. Miller <davem@davemloft.net>

IPv6 does not allow fragmentation by routers, so there is no
fragmentation ID in the fixed header.  UFO for IPv6 requires the ID to
be passed separately, but there is no provision for this in the virtio
net protocol.

Until recently our software implementation of UFO/IPv6 generated a new
ID, but this was a bug.  Now we will use ID=0 for any UFO/IPv6 packet
passed through a tap, which is even worse.

Unfortunately there is no distinction between UFO/IPv4 and v6
features, so disable UFO on taps and virtio_net completely until we
have a proper solution.

We cannot depend on VM managers respecting the tap feature flags, so
keep accepting UFO packets but log a warning the first time we do
this.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 916e4cf4 ("ipv6: reuse ip6_frag_id from ip6_ufo_append_data")
Signed-off-by: David S. Miller <davem@davemloft.net>

Some drivers are unable to perform TX completions in a bound time.
They instead call skb_orphan()

Problem is skb_fclone_busy() has to detect this case, otherwise
we block TCP retransmits and can freeze unlucky tcp sessions on
mostly idle hosts.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 1f3279ae ("tcp: avoid retransmits of TCP packets hanging in host queues")
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, skb_inner_network_header is used but this does not account
for Ethernet header for ETH_P_TEB. Use skb_inner_mac_header which
handles TEB and also should work with IP encapsulation in which case
inner mac and inner network headers are the same.

Tested: Ran TCP_STREAM over GRE, worked as expected.
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4 driver encapsulation/steering fixes

The 1st patch fixes a bug in the TX path that supports offloading the
TX checksum of (VXLAN) encapsulated TCP packets. It turns out that the
bug is revealed only when the receiver runs in non-offloaded mode, so
we somehow missed it so far... please queue it for -stable >= 3.14

The 2nd patch makes sure not to leak steering entry on error flow,
please queue it to 3.17-stable
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If mlx4_ib_create_flow() attempts to create > 1 rules with the
firmware, and one of these registrations fail, we leaked the
already created flow rules.

One example of the leak is when the registration of the VXLAN ghost
steering rule fails, we didn't unregister the original rule requested
by the user, introduced in commit d2fce8a9 "mlx4: Set
user-space raw Ethernet QPs to properly handle VXLAN traffic".

While here, add dump of the VXLAN portion of steering rules
so it can actually be seen when flow creation fails.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For VXLAN/NVGRE encapsulation, the current HW doesn't support offloading
both the outer UDP TX checksum and the inner TCP/UDP TX checksum.

The driver doesn't advertize SKB_GSO_UDP_TUNNEL_CSUM, however we are wrongly
telling the HW to offload the outer UDP checksum for encapsulated packets,
fix that.

Fixes: 837052d0 ('net/mlx4_en: Add netdev support for TCP/IP
		     offloads of vxlan tunneling')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2014-10-30

This series contains updates to e1000, igb and ixgbe.

Francesco Ruggeri fixes an issue with e1000 where in a VM the driver did
not support unicast filtering.

Roman Gushchin fixes an issue with igb where the driver was re-using
mapped pages so that packets were still getting dropped even if all
the memory issues are gone and there is free memory.

Junwei Zhang found where in the ixgbe_clean_rx_ring() we were repeating
the assignment of NULL to the receive buffer skb and fixes it.

Emil fixes a race condition between setup_link and SFP detection routine
in the watchdog when setting the advertised speed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If we cache them, the kernel will reuse them, independently of
whether forwarding is enabled or not.  Which means that if forwarding is
disabled on the input interface where the first routing request comes
from, then that unreachable result will be cached and reused for
other interfaces, even if forwarding is enabled on them.  The opposite
is also true.

This can be verified with two interfaces A and B and an output interface
C, where B has forwarding enabled, but not A and trying
ip route get $dst iif A from $src && ip route get $dst iif B from $src
Signed-off-by: Nicolas Cavallari <nicolas.cavallari@green-communications.fr>
Reviewed-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>

win0_lock was being used un-initialized, resulting in warning traces
being seen when lock debugging is enabled (and just wrong)

Fixes : fc5ab020 ('cxgb4: Replaced the backdoor mechanism to access the HW
 memory with PCIe Window method')
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hayes Wang says:

====================
r8152: patches for autosuspend

There are unexpected processes when enabling autosuspend.
These patches are used to fix them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid unnecessary behavior when autosuspend occurs during open().
The relative processes should only be run after finishing open().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

If (tp->speed & LINK_STATUS) is not zero, the rtl8152_resume()
would call rtl_start_rx() before enabling the tx/rx. Avoid this
by resetting it to zero.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The flag of SELECTIVE_SUSPEND should be cleared when autoresuming.
Otherwise, when the system suspend and resume occur, it may have
the wrong flow.

Besides, because the flag of SELECTIVE_SUSPEND couldn't be used
to check if the hw enables the relative feature, it should alwayes
be disabled in close().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Following commands:

modprobe ixgbe
ifconfig ethX up
ethtool -s ethX advertise 0x020

can lead to "setup link failed with code -14" error due to the setup_link
call racing with the SFP detection routine in the watchdog.

This patch resolves this issue by protecting the setup_link call with check
for __IXGBE_IN_SFP_INIT.
Reported-by: Scott Harrison <scoharr2@cisco.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Martin Zhang <martinbj2008@gmail.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Incoming packet is dropped silently by sk_filter(), if the skb was
allocated from pfmemalloc reserves and the corresponding socket is
not marked with the SOCK_MEMALLOC flag.

Igb driver allocates pages for DMA with __skb_alloc_page(), which
calls alloc_pages_node() with the __GFP_MEMALLOC flag. So, in case
of OOM condition, igb can get pages with pfmemalloc flag set.

If an incoming packet hits the pfmemalloc page and is large enough
(small packets are copying into the memory, allocated with
netdev_alloc_skb_ip_align(), so they are not affected), it will be
dropped.

This behavior is ok under high memory pressure, but the problem is
that the igb driver reuses these mapped pages. So, packets are still
dropping even if all memory issues are gone and there is a plenty
of free memory.

In my case, some TCP sessions hang on a small percentage (< 0.1%)
of machines days after OOMs.

Fix this by avoiding reuse of such pages.
Signed-off-by: Roman Gushchin <klamm@yandex-team.ru>
Tested-by: Aaron Brown "aaron.f.brown@intel.com"
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

VMWare's e1000 implementation does not seem to support unicast filtering.
This can be observed by configuring a macvlan interface on eth0 in a VM in
VMWare Fusion 5.0.5, and trying to use that interface instead of eth0.
Tested on 3.16.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The WARN_ON in inet_evict_bucket can be triggered by a valid case:
inet_frag_kill and inet_evict_bucket can be running in parallel on the
same queue which means that there has been at least one more ref added
by a previous inet_frag_find call, but inet_frag_kill can delete the
timer before inet_evict_bucket which will cause the WARN_ON() there to
trigger since we'll have refcnt!=1. Now, this case is valid because the
queue is being "killed" for some reason (removed from the chain list and
its timer deleted) so it will get destroyed in the end by one of the
inet_frag_put() calls which reaches 0 i.e. refcnt is still valid.

CC: Florian Westphal <fw@strlen.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McLean <chutzpah@gentoo.org>

Fixes: b13d3cbf ("inet: frag: move eviction of queues to work queue")
Reported-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the evictor is running it adds some chosen frags to a local list to
be evicted once the chain lock has been released but at the same time
the *frag_queue can be running for some of the same queues and it
may call inet_frag_kill which will wait on the chain lock and
will then delete the queue from the wrong list since it was added in the
eviction one. The fix is simple - check if the queue has the evict flag
set under the chain lock before deleting it, this is safe because the
evict flag is set only under that lock and having the flag set also means
that the queue has been detached from the chain list, so no need to delete
it again.
An important note to make is that we're safe w.r.t refcnt because
inet_frag_kill and inet_evict_bucket will sync on the del_timer operation
where only one of the two can succeed (or if the timer is executing -
none of them), the cases are:
1. inet_frag_kill succeeds in del_timer
 - then the timer ref is removed, but inet_evict_bucket will not add
   this queue to its expire list but will restart eviction in that chain
2. inet_evict_bucket succeeds in del_timer
 - then the timer ref is kept until the evictor "expires" the queue, but
   inet_frag_kill will remove the initial ref and will set
   INET_FRAG_COMPLETE which will make the frag_expire fn just to remove
   its ref.
In the end all of the queue users will do an inet_frag_put and the one
that reaches 0 will free it. The refcount balance should be okay.

CC: Florian Westphal <fw@strlen.de>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McLean <chutzpah@gentoo.org>

Fixes: b13d3cbf ("inet: frag: move eviction of queues to work queue")
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Patrick McLean <chutzpah@gentoo.org>
Tested-by: Patrick McLean <chutzpah@gentoo.org>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Remove the rcu_read_lock/unlock around rcu_access_pointer
2. Replace the rcu_dereference with rcu_access_pointer
Signed-off-by: Tej Parkash <tej.parkash@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Replaced repetive Device ID's which got added in commit b961f9a4
("cxgb4vf: Remove superfluous "idx" parameter of CH_DEVICE() macro")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NetworkManager might want to know that it changed when the router advertisement
arrives.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: Vijay Subramanian <vijaynsu@cisco.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>

Olivier Blin says:

====================
cdc-ether: handle promiscuous mode

Since kernel 3.16, my Lenovo USB network adapters (RTL8153) using
cdc-ether are not working anymore in a bridge.

This is due to commit c472ab68, which
resets the packet filter when the device is bound.

The default packet filter set by cdc-ether does not include
promiscuous, while the adapter seemed to have promiscuous enabled by
default.

This patch series allows to support promiscuous mode for cdc-ether, by
hooking into set_rx_mode.

Incidentally, maybe this device should be handled by the r8152 driver,
but this patch series is still nice for other adapters.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Oliver Neukum <oneukum@suse.de>

Promiscuous mode was not supported anymore with my Lenovo adapters
(RTL8153) since commit c472ab68
(cdc-ether: clean packet filter upon probe).

It was not possible to use them in a bridge anymore.
Signed-off-by: Olivier Blin <olivier.blin@softathome.com>
Also-analyzed-by: Loïc Yhuel <loic.yhuel@softathome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>