A sanity test for BPF_MAP_TYPE_PERCPU_HASH.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The functions bpf_map_lookup_elem(map, key, value) and
bpf_map_update_elem(map, key, value, flags) need to get/set
values from all-cpus for per-cpu hash and array maps,
so that user space can aggregate/update them as necessary.

Example of single counter aggregation in user space:
  unsigned int nr_cpus = sysconf(_SC_NPROCESSORS_CONF);
  long values[nr_cpus];
  long value = 0;

  bpf_lookup_elem(fd, key, values);
  for (i = 0; i < nr_cpus; i++)
    value += values[i];

The user space must provide round_up(value_size, 8) * nr_cpus
array to get/set values, since kernel will use 'long' copy
of per-cpu values to try to copy good counters atomically.
It's a best-effort, since bpf programs and user space are racing
to access the same memory.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Primary use case is a histogram array of latency
where bpf program computes the latency of block requests or other
events and stores histogram of latency into array of 64 elements.
All cpus are constantly running, so normal increment is not accurate,
bpf_xadd causes cache ping-pong and this per-cpu approach allows
fastest collision-free counters.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Introduce BPF_MAP_TYPE_PERCPU_HASH map type which is used to do
accurate counters without need to use BPF_XADD instruction which turned
out to be too costly for high-performance network monitoring.
In the typical use case the 'key' is the flow tuple or other long
living object that sees a lot of events per second.

bpf_map_lookup_elem() returns per-cpu area.
Example:
struct {
  u32 packets;
  u32 bytes;
} * ptr = bpf_map_lookup_elem(&map, &key);
/* ptr points to this_cpu area of the value, so the following
 * increments will not collide with other cpus
 */
ptr->packets ++;
ptr->bytes += skb->len;

bpf_update_elem() atomically creates a new element where all per-cpu
values are zero initialized and this_cpu value is populated with
given 'value'.
Note that non-per-cpu hash map always allocates new element
and then deletes old after rcu grace period to maintain atomicity
of update. Per-cpu hash map updates element values in-place.
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

netdev_rss_key is written to once and thereafter is read by
drivers when they are initialising. The fact that it is mostly
read and not written to makes it a candidate for a __read_mostly
declaration.
Signed-off-by: Kim Jones <kim-marie.jones@intel.com>
Signed-off-by: Alan Carey <alan.carey@intel.com>
Acked-by: Rami Rosen <rami.rosen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
tcp: fastopen: accept data/FIN present in SYNACK

Implements RFC 7413 (TCP Fast Open) 4.2.2, accepting payload and/or FIN
in SYNACK messages, and prepare removal of SYN flag in tcp_recvmsg()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

If we remove the SYN flag from the skbs that tcp_fastopen_add_skb()
places in socket receive queue, then we can remove the test that
tcp_recvmsg() has to perform in fast path.

All we have to do is to adjust SEQ in the slow path.

For the moment, we place an unlikely() and output a message
if we find an skb having SYN flag set.
Goal would be to get rid of the test completely.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RFC 7413 (TCP Fast Open) 4.2.2 states that the SYNACK message
MAY include data and/or FIN

This patch adds support for the client side :

If we receive a SYNACK with payload or FIN, queue the skb instead
of ignoring it.

Since we already support the same for SYN, we refactor the existing
code and reuse it. Note we need to clone the skb, so this operation
might fail under memory pressure.

Sara Dickinson pointed out FreeBSD server Fast Open implementation
was planned to generate such SYNACK in the future.

The server side might be implemented on linux later.
Reported-by: Sara Dickinson <sara@sinodun.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jarod Wilson says:

====================
net: add and use rx_nohandler stat counter

The network core tries to keep track of dropped packets, but some packets
you wouldn't really call dropped, so much as intentionally ignored, under
certain circumstances. One such case is that of bonding and team device
slaves that are currently inactive. Their respective rx_handler functions
return RX_HANDLER_EXACT (the only places in the kernel that return that),
which ends up tracking into the network core's __netif_receive_skb_core()
function's drop path, with no pt_prev set. On a noisy network, this can
result in a very rapidly incrementing rx_dropped counter, not only on the
inactive slave(s), but also on the master device, such as the following:

$ cat /proc/net/dev
Inter-|   Receive                                                |  Transmit
 face |bytes    packets errs drop fifo frame compressed multicast|bytes    packets errs drop fifo colls carrier compressed
  p7p1: 14783346  140430    0 140428    0     0          0      2040      680       8    0    0    0     0       0          0
  p7p2: 14805198  140648    0    0    0     0          0      2034        0       0    0    0    0     0       0          0
 bond0: 53365248  532798    0 421160    0     0          0    115151     2040      24    0    0    0     0       0          0
    lo:    5420      54    0    0    0     0          0         0     5420      54    0    0    0     0       0          0
  p5p1: 19292195  196197    0 140368    0     0          0     56564      680       8    0    0    0     0       0          0
  p5p2: 19289707  196171    0 140364    0     0          0     56547      680       8    0    0    0     0       0          0
   em3: 20996626  158214    0    0    0     0          0       383        0       0    0    0    0     0       0          0
   em2: 14065122  138462    0    0    0     0          0       310        0       0    0    0    0     0       0          0
   em1: 14063162  138440    0    0    0     0          0       308        0       0    0    0    0     0       0          0
   em4: 21050830  158729    0    0    0     0          0       385    71662     469    0    0    0     0       0          0
   ib0:       0       0    0    0    0     0          0         0        0       0    0    0    0     0       0          0

In this scenario, p5p1, p5p2 and p7p1 are all inactive slaves in an
active-backup bond0, and you can see that all three have high drop counts,
with the master bond0 showing a tally of all three.

I know that this was previously discussed some here:

    http://www.spinics.net/lists/netdev/msg226341.html

It seems additional counters never came to fruition, so this is a first
attempt at creating one of them, so that we stop calling these drops,
which for users monitoring rx_dropped, causes great alarm, and renders the
counter much less useful for them.

This adds a sysfs statistics node and makes the counter available via
netlink.

Additionally, I'm not certain if this set qualifies for net, or if it
should be put aside and resubmitted for net-next after 4.5 is put to
bed, but I do have users who consider this an important bugfix.

This has been tested quite a bit on x86_64, and now lightly on i686 as
well, to verify functionality of updates to netdev_stats_to_stats64()
on 32-bit arches.
====================
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sample output with this set applied for an active-backup bond:

$ cat /sys/devices/virtual/net/bond0/lower_p7p1/statistics/rx_nohandler
16568
$ cat /sys/devices/virtual/net/bond0/lower_p5p2/statistics/rx_nohandler
16583
$ cat /sys/devices/virtual/net/bond0/statistics/rx_nohandler
33151

CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

CC: Jiri Pirko <jiri@resnulli.us>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds an rx_nohandler stat counter, along with a sysfs statistics
node, and copies the counter out via netlink as well.

CC: "David S. Miller" <davem@davemloft.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jiri@mellanox.com>
CC: Daniel Borkmann <daniel@iogearbox.net>
CC: Tom Herbert <tom@herbertland.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <gospo@cumulusnetworks.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The netdev_stats_to_stats64 function copies the deprecated
net_device_stats format stats into rtnl_link_stats64 for legacy support
purposes, but with the BUILD_BUG_ON as it was, it wasn't possible to
extend rtnl_link_stats64 without also extending net_device_stats. Relax
the BUILD_BUG_ON to only require that rtnl_link_stats64 is larger, and
zero out all the stat counters that aren't present in net_device_stats.

CC: Eric Dumazet <edumazet@google.com>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently link priority changes isn't handled for active links. In
this patch we resolve this by changing our priority if the peer passes
a valid priority in a state message.
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changing certain link attributes (link tolerance and link priority)
from the TIPC management tool is supposed to automatically take
effect at both endpoints of the affected link.

Currently the media address is not instantiated for the link and is
used uninstantiated when crafting protocol messages designated for the
peer endpoint. This means that changing a link property currently
results in the property being changed on the local machine but the
protocol message designated for the peer gets lost. Resulting in
property discrepancy between the endpoints.

In this patch we resolve this by using the media address from the
link entry and using the bearer transmit function to send it. Hence,
we can now eliminate the redundant function tipc_link_prot_xmit() and
the redundant field tipc_link::media_addr.

Fixes: 2af5ae37 (tipc: clean up unused code and structures)
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reported-by: Jason Hu <huzhijiang@gmail.com>
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2016-02-03

This series contains updates to i40e and i40evf only.

Kiran adds the MAC filter element to the end of the list instead of HEAD
just in case there are ever any ordering issues in the future.

Anjali fixes several RSS issues, first fixes the hash PCTYPE enable for
X722 since it supports a broader selection of PCTYPES for TCP and UDP.
Then fixes a bug in XL710, X710, and X722 support for RSS since we cannot
reduce the 4-tuple for RSS for TCP/IPv4/IPv6 or UDP/IPv4/IPv6 packets
since this requires a product feature change coming in a later release.
Cleans up the reset code where the restart-autoneg workaround is
applied, since X722 does not need the workaround, add a flag to indicate
which MAC and firmware version require the workaround to be applied.
Adds new device id's for X722 and code to add their support.  Also
adds another way to access the RSS keys and lookup table using the admin
queue for X722 devices.

Catherine updates the driver to replace the MAC check with a feature
flag check for 100M SGMII, since it is only support on X722 devices
currently.

Mitch reworks the VF driver to allow channel bonding, which was not
possible before this patch due to the asynchronous nature of the admin
queue mechanism.  Also fixes a rare case which causes a panic if the
VF driver is removed during reset recovery, resolve this by setting the
ring pointers to NULL after freeing them.

Shannon cleans up the driver where device capabilities were defined in
two different places, and neither had all the definitions, so he
consolidates the definitions in the admin queue API.  Also adds the new
proxy-wake-on-lan capability bit available with the new X722 device.
Lastly, added the new External Device Power Ability field to the
get_link_status data structure by using a reserved field at the end
of the structure.

Jesse mimics the ixgbe driver's use of a private work queue in the i40e
and i40evf drivers to avoid blocking the system work queue.

Greg cleans up the driver to limit the firmware revision checks to
properly handle DCB configurations from the firmware to the older
devices which need these checks (specifically X710 and XL710 devices
only).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When we create IPvlan slave; we use ether_setup() and that
sets up default MTU to 1500 while the master device may have
lower / different MTU. Any subsequent changes to the masters'
MTU are reflected into the slaves' MTU setting. However if those
don't happen (most likely scenario), the slaves' MTU stays at
1500 which could be bad.

This change adds code to inherit MTU from the master device
instead of using the default value during the link initialization
phase.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Tim Hockins <thockins@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add some missing reporting/advertisement of 100Mb capability
for adapters that support it.

Change-ID: I8b8523fbdc99517bec29d90c71b3744db11542ac
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the new External Device Power Ability field to the get_link_status data
structure, using space from the reserved field at the end of the struct.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix the name of the new cloud tunnel type from the place-holder NGE
name to the official Geneve.  Also fix the spelling of the VXLAN type.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>

Add the AQ opcode and struct definitions for the Run PHY Activity command
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Kevin Scott <kevin.c.scott@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

X710/XL710 devices require FW version checks to properly handle DCB
configurations from the FW.  Newer devices do not, so limit these checks
to X710/XL710.
Signed-off-by: Greg Bowers <gregory.j.bowers@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the new proxy-wake-on-lan capability bit available with the
new X722 device.
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

As done per ixgbe, use a private workqueue to avoid blocking the
system workqueue.  This avoids some strange side effects when
some other entity is depending on the system work queue.

Change-ID: Ic8ba08f5b03696cf638b21afd25fbae7738d55ee
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add write-back on interrupt throttle rate timer expiration support
for the i40evf driver, when running on X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The PCTYPES for the X710 and X722 families are different. This patch
makes adjustments for that.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds another way to access the RSS keys and lut using the AQ
for X722 devices.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the KX and QSFP device IDs for X722.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump.

Change-ID: Ic9a495feb9ab0606f953c3848b0acf67169d3930
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Synchronize code bases and add SCTP offload support.

Change-ID: I9f99071f7176225479026930c387bf681a47494e
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The restart-autoneg work around does not apply to X722.
Added a flag to set it only for the right MAC and right FW version
where the work around should be applied.
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Change-ID: I942c3ff40cccd1e56f424b1da776b020fe3c9d2a
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Since we check these ring pointers to make sure we don't double-allocate
or double-free the rings, we had better null them out after we free
them. In very rare cases this can cause a panic if the driver is removed
during reset recovery.

Change-ID: Ib06eb4910a3058275c8f7ec5ef7f45baa4674f96
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The device capabilities were defined in two places, and neither had all
the definitions.  It really belongs with the AQ API definition, so this
patch removes the other set of definitions and fills out the missing item.

Change-ID: I273ba7d79a476cd11d2e0ca5825fec1716740de2
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In some modes, bonding would not enslave VF interfaces. This is due to
bonding calling change_mtu and the immediately calling open. Because of
the asynchronous nature of the admin queue mechanism, the VF returns
-EBUSY to the open call, because it knows the previous operation hasn't
finished yet. This causes bonding to fail with a less-than-useful error
message.

To fix this, remove the check for pending operations at the beginning of
open. But this introduces a new bug where the driver will panic on a
quick close/open cycle. To fix that, we add a new driver state,
__I40EVF_DOWN_PENDING, that the driver enters when down is called. The
driver finally transitions to a fully DOWN state when it receives
confirmation from the PF driver that all the queues are disabled. This
allows open to complete even if there is a pending mtu change, and
bonding is finally happy.

Change-ID: I06f4c7e435d5bacbfceaa7c3f209e0ff04be21cc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

100M SGMII is only supported on X722.  Replace the mac check with
a feature flag check that is only set for the X722 device.

Change-ID: I53452d9af6af8cd9dca8500215fbc6ce93418f52
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the Hash PCTYPE enable for X722 since it supports
a broader selection of PCTYPES for TCP and UDP.

This patch also fixes a bug in XL710, X710, X722 support for RSS,
as of now we cannot reduce the (4)tuple for RSS for TCP/IPv4/IPV6 or
UDP/IPv4/IPv6 packets since this requires a product feature change
that comes in a later release.

A VF should never be allowed to change the tuples for RSS for any
PCTYPE since that's a global setting for the device in case of i40e
devices.

Change-ID: I0ee7203c9b24813260f58f3220798bc9d9ac4a12
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add MAC filter element to the end of the list in the given order,
just to be tidy, and just in case there are ever any ordering issues in
the future.

Change-ID: Idc15276147593ea9393ac72c861f9c7905a791b4
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull networking fixes from David Miller:
 "This looks like a lot but it's a mixture of regression fixes as well
  as fixes for longer standing issues.

   1) Fix on-channel cancellation in mac80211, from Johannes Berg.

   2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
      module, from Eric Dumazet.

   3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
      Dumazet.

   4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
      bound, from Craig Gallek.

   5) GRO key comparisons don't take lightweight tunnels into account,
      from Jesse Gross.

   6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
      Dumazet.

   7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
      register them, otherwise the NEWLINK netlink message is missing
      the proper attributes.  From Thadeu Lima de Souza Cascardo.

   8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
      Schimmel

   9) Handle fragments properly in ipv4 easly socket demux, from Eric
      Dumazet.

  10) Don't ignore the ifindex key specifier on ipv6 output route
      lookups, from Paolo Abeni"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
  tcp: avoid cwnd undo after receiving ECN
  irda: fix a potential use-after-free in ircomm_param_request
  net: tg3: avoid uninitialized variable warning
  net: nb8800: avoid uninitialized variable warning
  net: vxge: avoid unused function warnings
  net: bgmac: clarify CONFIG_BCMA dependency
  net: hp100: remove unnecessary #ifdefs
  net: davinci_cpdma: use dma_addr_t for DMA address
  ipv6/udp: use sticky pktinfo egress ifindex on connect()
  ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
  netlink: not trim skb for mmaped socket when dump
  vxlan: fix a out of bounds access in __vxlan_find_mac
  net: dsa: mv88e6xxx: fix port VLAN maps
  fib_trie: Fix shift by 32 in fib_table_lookup
  net: moxart: use correct accessors for DMA memory
  ipv4: ipconfig: avoid unused ic_proto_used symbol
  bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
  bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
  bnxt_en: Ring free response from close path should use completion ring
  net_sched: drr: check for NULL pointer in drr_dequeue
  ...

Pull crypto fixes from Herbert Xu:
 "This fixes the following issues:

  API:
   - algif_hash needs to wait for init operations to complete.
   - The has_key setting for shash was always true.

  Algorithms:
   - Add missing selections of CRYPTO_HASH.
   - Fix pkcs7 authentication.

  Drivers:
   - Fix stack alignment bug in chacha20-ssse3.
   - Fix performance regression in caam due to incorrect setting.
   - Fix potential compile-only build failure of stm32"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: atmel-aes - remove calls of clk_prepare() from atomic contexts
  crypto: algif_hash - wait for crypto_ahash_init() to complete
  crypto: shash - Fix has_key setting
  hwrng: stm32 - Fix dependencies for !HAS_IOMEM archs
  crypto: ghash,poly1305 - select CRYPTO_HASH where needed
  crypto: chacha20-ssse3 - Align stack pointer to 64 bytes
  PKCS#7: Don't require SpcSpOpusInfo in Authenticode pkcs7 signatures
  crypto: caam - make write transactions bufferable on PPC platforms