The BCM2835 GPIO module is a combined GPIO controller, (GPIO) interrupt
controller, and pinmux/control device.

Original driver by Simon Arlott.
Rewrite including GPIO chip device by Chris Boot.

Upstreaming changes by Stephen Warren:
* Wrote DT binding documentation.
* Changed brcm,function to an integer to more directly match the
  datasheet, and to match brcm,pins being an integer.
* Implemented pull-up/down pin config.
* Removed read-only DT property and related code. The restriction this
  implemented are driven by the board, not the GPIO HW block, so don't
  really make sense of a HW block binding, were in general incomplete
  (since they could only know about the few pins hard-coded into the
  Raspberry Pi B board design and not the uncommitted GPIOS), and are
  better represented simply by not writing incorrect data into pin
  configuration nodes.
* Don't set GPIO_IN function select in gpio_request_enable() to avoid
  glitches; defer this to gpio_set_direction(). Consequently, removed
  empty bcm2835_pmx_gpio_request_enable().
* Simplified enabled_irq_map[]; make it explicitly 1 entry per bank.
* Lifted use of enabled_irq_map[] outside the per-interrupt loop in
  IRQ handler, thus fixing an issue where the code was indexing into
  enabled_irq_map[] by intra-bank GPIO ID, not global GPIO ID.
* Removed locking in IRQ handler, since all other code uses
  spin_lock_irqsave() and so guarantees it doesn't run concurrently
  with the handler.
* Moved duplicated BUILD_BUG_ON()s into probe(). Also check size of
  bcm2835_gpio_pins[].
* Remove range-checking from bcm2835_pctl_get_groups_count() since we've
  decided to trust the pinctrl core.
* Made bcm2835_pmx_gpio_disable_free() call bcm2835_pinctrl_fsel_set()
  directly for simplicity.
* Fixed body of dt_free_map() to match latest dt_node_to_map().
* Removed GPIO ownership check from bcm2835_pmx_enable() since the pinctrl
  core owns doing this.
* Made irq_chip and pinctrl_gpio_range .name == MODULE_NAME so it's more
  descriptive.
* Simplified remove(); removed call to non-existent
  pinctrl_remove_gpio_range(), remove early return on error.
* Don't force gpiochip's base to 0. Set gpio_range.base to gpiochip's
  base GPIO number.
* Error-handling cleanups in probe().
* Switched to module_platform_driver() rather than open-coding.
* Made pin, group, and function names lower-case.
* s/broadcom/brcm/ in DT property names.
* s/2708/2835/.
* Fixed a couple minor checkpatch warnings, and other minor cleanup.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Chris Boot <bootc@bootc.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This pure documentation fix tries to align the "idle" and
"sleep" pin states to the idle and suspend states from
runtime PM.

Cc: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The code was using a homegrown method of looking up the offset
from the irq domain, not to be encouraged. Use the proper
irq_find_mapping() call instead.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch fixes the chained irq hang issue, tested by DM9000 driver using
GPIO0-3(irqnr=131) as the external IRQ on SiRFmarco:
   $ cat /proc/interrupts
               CPU0       CPU1
     32:       1608          0       GIC  sirfsoc_timer0
     33:          0       3197       GIC  sirfsoc_timer1
     50:      10207          0       GIC  sirfsoc-uart
     56:          2          0       GIC  cc0e0000.i2c
     70:         44          0       GIC  mmc0
    131:        333          0  sirf-gpio-irq  eth0
    ...
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This patch initializes the optional irq_chip pointer gc in sirfsoc
pinctrl_gpio_range.
Signed-off-by: Baohua Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

sirfsoc_gpio_set_input() is called in those functions which have
held the spinlock, so delete the duplicated locking.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

We always use pinctrl_request_gpio() to get GPIO, If we don't have these
missing pins in the pin list, gpio_request and related operations will fail
for them.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Return 0 while probing success.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Adds support for displaying the individual pin h/w config state.
Signed-off-by: Matt Porter <mporter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This defines the proper sleep states for all the I2C pins of
the MOP500 DB8500 ASIC setting.
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

'pindesc' was not freed when returning from an error induced
exit path.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This named the sleep mode pin configurations as *slpm* rather
than *sleep* to correspond better with the settings from the
datasheet. It also defines an optional sleep mode for the SPI
controller SPI2.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

GPIO216_AG12 is configured as a gpio for SPI2, so select
the spi2_oc1_2 pin group instead of spi2_oc1_1
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

fix smatch warning:
drivers/pinctrl/pinctrl-imx.c:435:21: warning: duplicate const
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The semantics of the interactions between GPIO and pinctrl may be
unclear, e.g. which one do you request first? This amends the
documentation to make this clear.
Reported-by: Domenico Andreoli <cavokz@gmail.com>
Acked-by: Domenico Andreoli <domenico.andreoli@linux.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Due to specific constraint, pin HSIT_ACWAKE0_a is
not driven by HSI block but as a GPIO.

Cc: arm@kernel.org
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Instead of using a temporary buffer, snprintf() and kstrdup(), just
use kasprintf() that does the same thing in just oneline.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Colin Cross <ccross@google.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

With pinctrl-single,bits it is possible to update just part of the register
within the pinctrl-single,function-mask area.
This is useful when one register configures mmore than one pin's mux.

pinctrl-single,bits takes three parameters:
<reg offset, value, sub-mask>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
[Removed a misplaced comment]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Another possible pin configuration for the MC1 pin group.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Use the pcs->fmask to make sure that the value is not changing (setting)
bits in areas where it should not.
To avoid situations like this:

pmx_dummy: pinmux@4a100040 {
	compatible = "pinctrl-single";
	reg = <0x4a100040 0x0196>;
	#address-cells = <1>;
	#size-cells = <0>;
	pinctrl-single,register-width = <16>;
	pinctrl-single,function-mask = <0x00ff>;
};

&pmx_dummy {
	pinctrl-names = "default";
	pinctrl-0 = <&board_pins>;

	board_pins: pinmux_board_pins {
		pinctrl-single,pins = <
			0x6c 0xf0f
			0x6e 0x10f
			0x70 0x23f
			0x72 0xa5f
		>;
	};
};
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

ux500 machines performs pins (GPIO) reconfiguration when entering
in the suspended mode. This reconfiguration aims at reaching an ultra
low power HW configuration.

Due to this HW reconfiguration, some HW devices can change of HW state
and have their output signals at level that could generate IRQs.

If the non-wakeup IRQs are disabled but not yet masked (delayed interrupt
disable feature from the generic irq layer), effective interrupts reach
the system only because the system attempt to enter the suspended mode.

To prevent such IRQs to trig, all irq chips embedded in ux500 platform
should enable their IRQCHIP_MASK_ON_SUSPEND flag.
Signed-off-by: Etienne Carriere <etienne.carriere@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Unlike imx6q pinctrl driver that starts nubmering pad from 0, imx5
pinctrl drivers number pad from 1.  It causes problem/confusion when
driver accesses imx51_pinctrl_pads array using pin ID as the index.

Change imx51_pads and imx53_pads numbering start from 0.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This is mostly cut'n'paste from the imx51 pinctrl driver.
The data was generated using sed and awk on
arch/arm/plat-mxc/include/mach/iomux-mx35.h.

Changes since (implicit) v1
 - remove references to file names in binding documentation
 - remove sed commands from comments in driver
 - add explicit numbers for pins and functions
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This converts the Nomadik to using pin control using the
driver for the STN8815 ASIC.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This adds support for the STN8815 ASIC for the Nomadik pin
controller.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This implements a subdriver for the DB8540 ASIC for the
Nomadik pin controller.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Reviewed-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This doesn't change semantics, just looks nicer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Andreas Bombe reported that the added ktime_t overflow checking added to
timespec_valid in commit 4e8b1452 ("time: Improve sanity checking of
timekeeping inputs") was causing problems with X.org because it caused
timeouts larger then KTIME_T to be invalid.

Previously, these large timeouts would be clamped to KTIME_MAX and would
never expire, which is valid.

This patch splits the ktime_t overflow checking into a new
timespec_valid_strict function, and converts the timekeeping codes
internal checking to use this more strict function.
Reported-and-tested-by: Andreas Bombe <aeb@debian.org>
Cc: Zhouping Liu <zliu@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull KVM bugfixes from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: x86: fix KVM_GET_MSR for PV EOI
  kvm: Fix nonsense handling of compat ioctl

Pull PARISC fixes from James Bottomley:
 "This is a set of two bug fixes.  One is the ATOMIC problem which is
  now causing a compile failure in certain situations.  The other is
  mishandling of PER_LINUX32 which may also cause user visible effects.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] fix personality flag check in copy_thread()
  [PARISC] Redefine ATOMIC_INIT and ATOMIC64_INIT to drop the casts

Pull s390 fixes from Martin Schwidefsky:
 "A couple of s390 bug fixes for 3.5-rc4"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/32: Don't clobber personality flags on exec
  s390/smp: add missing smp_store_status() for !SMP
  s390/dasd: fix ioctl return value
  s390: Always use "long" for ssize_t to match size_t

Pull drm fixes from Dave Airlie:
 "A bunch of scattered fixes ati/intel/nouveau, couple of core ones,
  nothing too shocking or different."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm: Add EDID_QUIRK_FORCE_REDUCED_BLANKING for ASUS VW222S
  gma500: Consider CRTC initially active.
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS
  drm/nvc0/copy: check PUNITS to determine which copy engines are disabled
  i915: Quirk no_lvds on Gigabyte GA-D525TUD ITX motherboard
  drm/i915: Use the correct size of the GTT for placing the per-process entries
  drm: Check for invalid cursor flags
  drm: Initialize object type when using DRM_MODE() macro
  drm/i915: fix color order for BGR formats on IVB
  drm/i915: fix wrong order of parameters in port checking functions

In native 32 bit mode the personality flags were not correctly inherited.
This is the s390 version of 59e4c3a2 "powerpc/32: Don't clobber personality
flags on exec".
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>

Connecting an ASUS VW222S [1] over VGA a garbled screen is shown with
vertical stripes in the top half.

In commit bc42aabc [2]

        commit bc42aabc
        Author: Adam Jackson <ajax@redhat.com>
        Date:   Wed May 23 16:26:54 2012 -0400

            drm/edid/quirks: ViewSonic VA2026w

Adam Jackson added the quirk `EDID_QUIRK_FORCE_REDUCED_BLANKING` which
is also needed for this ASUS monitor.

All log files and output from `xrandr` is included in the referenced
Bugzilla report #17629.

Please note that this monitor only has a VGA (D-Sub) connector [1].

[1] http://www.asus.com/Display/LCD_Monitors/VW222S/
[2] http://git.kernel.org/?p=linux/kernel/git/torvalds/linux.git;a=commit;h=bc42aabc6a01b92b0f961d65671564e0e1cd7592

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=17629Signed-off-by: Paul Menzel <paulepanter@users.sourceforge.net>
Cc: <dri-devel@lists.freedesktop.org>
Cc: Adam Jackson <ajax@redhat.com>
Cc: Ian Pilcher <arequipeno@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Alex writes:

Highlights:
- fix a gart regression on older IGP chips
- more MSAA fixes
- fix a double free in gpu reset code
- modesetting fixes
- trinity dig encoder fix.

* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: fix dig encoder selection on DCE61
  drm/radeon: fix double free in radeon_gpu_reset
  drm/radeon: force dma32 to fix regression rs4xx,rs6xx,rs740
  drm/radeon: rework panel mode setup
  drm/radeon/atom: powergating fixes for DCE6
  drm/radeon/atom: rework DIG modesetting on DCE3+
  drm/radeon: don't disable plls that are in use by other crtcs
  drm/radeon: add proper checking of RESOLVE_BOX command for r600-r700
  drm/radeon: initialize tracked CS state
  drm/radeon: fix reading CB_COLORn_MASK from the CS

[this one ideally should make 3.6 - it fixes the very annoying mode setting bug]

This causes the pipe to be forced off prior to initial mode set, which
roughly mirrors the behavior of the i915 driver.  It fixes initial mode
setting on my Intel DN2800MT (Cedarview) board.  Without it, mode
setting triggers an out-of-range error from the monitor for most modes,
but only on initial configuration (i.e. they can be configured
successfully from userspace after that).
Signed-off-by: Forest Bond <forest.bond@rapidrollout.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Was using the DCE41 code which was wrong. Fixes
blank displays on a number of Trinity systems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Pull btrfs fixes from Chris Mason:
 "I've split out the big send/receive update from my last pull request
  and now have just the fixes in my for-linus branch.  The send/recv
  branch will wander over to linux-next shortly though.

  The largest patches in this pull are Josef's patches to fix DIO
  locking problems and his patch to fix a crash during balance.  They
  are both well tested.

  The rest are smaller fixes that we've had queued.  The last rc came
  out while I was hacking new and exciting ways to recover from a
  misplaced rm -rf on my dev box, so these missed rc3."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (25 commits)
  Btrfs: fix that repair code is spuriously executed for transid failures
  Btrfs: fix ordered extent leak when failing to start a transaction
  Btrfs: fix a dio write regression
  Btrfs: fix deadlock with freeze and sync V2
  Btrfs: revert checksum error statistic which can cause a BUG()
  Btrfs: remove superblock writing after fatal error
  Btrfs: allow delayed refs to be merged
  Btrfs: fix enospc problems when deleting a subvol
  Btrfs: fix wrong mtime and ctime when creating snapshots
  Btrfs: fix race in run_clustered_refs
  Btrfs: don't run __tree_mod_log_free_eb on leaves
  Btrfs: increase the size of the free space cache
  Btrfs: barrier before waitqueue_active
  Btrfs: fix deadlock in wait_for_more_refs
  btrfs: fix second lock in btrfs_delete_delayed_items()
  Btrfs: don't allocate a seperate csums array for direct reads
  Btrfs: do not strdup non existent strings
  Btrfs: do not use missing devices when showing devname
  Btrfs: fix that error value is changed by mistake
  Btrfs: lock extents as we map them in DIO
  ...

Pull watchdog fixes from Wim Van Sebroeck:
 "This will fix a warning for watchdog-test.c and it will remove a
  duplicate include of delay.h"

* git://www.linux-watchdog.org/linux-watchdog:
  watchdog: da9052: Remove duplicate inclusion of delay.h
  watchdog: fix watchdog-test.c build warning