Add the enum br_mrp_hw_support that is used by the br_mrp_switchdev
functions to allow the SW to detect the cases where HW can't implement
the functionality or when SW is used as a backup.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the member sw_backup to the structures switchdev_obj_ring_role_mrp
and switchdev_obj_in_role_mrp. In this way the SW can call the driver in
2 ways, once when sw_backup is set to false, meaning that the driver
should implement this completely in HW. And if that is not supported the
SW will call again but with sw_backup set to true, meaning that the
HW should help or allow the SW to run the protocol.

For example when role is MRM, if the HW can't detect when it stops
receiving MRP Test frames but it can trap these frames to CPU, then it
needs to return -EOPNOTSUPP when sw_backup is false and return 0 when
sw_backup is true.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove #IS_ENABLED(CONFIG_BRIDGE_MRP) from switchdev.h. This will
simplify the code implements MRP callbacks and will be similar with the
vlan filtering.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When 88E1111 is operating in SGMII mode, auto-negotiation should be enabled
on the SGMII side so that the link will come up properly with PCSes which
normally have auto-negotiation enabled. This is normally the case when the
PHY defaults to SGMII mode at power-up, however if we switched it from some
other mode like 1000Base-X, as may happen in some SFP module situations,
it may not be, particularly for modules which have 1000Base-X
auto-negotiation defaulting to disabled.

Call genphy_check_and_restart_aneg on the fiber page to ensure that auto-
negotiation is properly enabled on the SGMII interface.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marek Behún says:

====================-
Add 5gbase-r PHY interface mode

there is still some testing needed for Amethyst patches, so I have
split the part adding support for 5gbase-r interface mode and am sending
it alone.

The first two patches are already reviewed.

Changes since last patches (Amethyst v16):
- added phylink 5gbase-r handler
- added SFP support for 5gbase-r mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The sfp_parse_support() function is setting 5000baseT_Full in some cases.
Now that we have PHY_INTERFACE_MODE_5GBASER interface mode available,
change sfp_select_interface() to return PHY_INTERFACE_MODE_5GBASER if
5000baseT_Full is set in the link mode mask.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 5GBASER interface type and speed to phylink.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 5GBASE-R phy interface mode
Signed-off-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 5gbase-r PHY interface mode.
Signed-off-by: Pavana Sharma <pavana.sharma@digi.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The tg3 driver tried to communicate towards the PHY driver whether it
wanted RGMII in-band signaling enabled or disabled however there is
nothing that looks at those flags in drivers/net/phy/broadcom.c so this
does do not anything.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bjarni Jonasson says:

====================
Fixes applied to VCS8514

3 different fixes applied to VSC8514:
LCPLL reset, serdes calibration and coma mode disabled.
Especially the serdes calibration is large and is now placed
in a new file 'mscc_serdes.c' which can act as
a placeholder for future serdes configuration.

v1 -> v2:
  Preserved reversed christmas tree
  Removed forward definitions
  Fixed build issues
  Changed net to net-next

v2 -> v3:
  Added cover letter.
  Removed ena_clk_bypass from function call
  Created mscc_serdes.c and .h for serdes configuration
  Modified coma register config.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The 'coma mode' (configurable through sw or hw) provides an
optional feature that may be used to control when the PHYs become active.
The typical usage is to synchronize the link-up time across
all PHY instances. This patch releases coma mode if not done by hardware,
otherwise the phys will not link-up.

Fixes: e4f9ba64 ("net: phy: mscc: add support for VSC8514 PHY.")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current IB serdes calibration algorithm (performed by the onboard 8051)
has proven to be unstable for the VSC8514 QSGMII phy.
A new algorithm has been developed based on
'Frequency-offset Jittered-Injection' or 'FoJi' method which solves
all known issues.  This patch disables the 8051 algorithm and
replaces it with the new FoJi algorithm.
The calibration is now performed in a new file (mscc_serdes.c),
which can act as an placeholder for future serdes configurations.

Fixes: e4f9ba64 ("net: phy: mscc: add support for VSC8514 PHY.")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At Power-On Reset, transients may cause the LCPLL to lock onto a
clock that is momentarily unstable. This is normally seen in QSGMII
setups where the higher speed 6G SerDes is being used.
This patch adds an initial LCPLL Reset to the PHY (first instance)
to avoid this issue.

Fixes: e4f9ba64 ("net: phy: mscc: add support for VSC8514 PHY.")
Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Fix buggy brport flags offload for SJA1105 DSA

I am resending this series because the title and the patches were mixed
up and these patches were lost. This series' cover letter was used as
the merge commit for the unrelated "Fixing build breakage after "Merge
branch 'Propagate-extack-for-switchdev-LANs-from-DSA'"" series, as can
be seen below:
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next.git/commit/?id=ca04422afd6998611a81d0ea1b61d5a5f4923f84

while the actual patches from the "Fix buggy brport flags offload for
SJA1105 DSA" series were marked as superseded and not applied:
https://patchwork.kernel.org/project/netdevbpf/cover/20210214155704.1784220-1-olteanv@gmail.com/
which they should have.

I know with so many bugs I introduced it's hard to keep track, I'm sorry.

Original series description:

While testing software bridging on sja1105, I discovered that I managed
to introduce two bugs in a single patch submitted recently to net-next.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Quite embarrasingly, I managed to fool myself into thinking that the
flooding domain of sja1105 source ports is restricted by the forwarding
domain, which it isn't. Frames which match an FDB entry are forwarded
towards that entry's DESTPORTS restricted by REACH_PORT[SRC_PORT], while
frames that don't match any FDB entry are forwarded towards
FL_DOMAIN[SRC_PORT] or BC_DOMAIN[SRC_PORT].

This means we can't get away with doing the simple thing, and we must
manage the flooding domain ourselves such that it is restricted by the
forwarding domain. This new function must be called from the
.port_bridge_join and .port_bridge_leave methods too, not just from
.port_bridge_flags as we did before.

Fixes: 4d942354 ("net: dsa: sja1105: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Due to a mistake, the driver always sets the address learning flag to
the previously stored value, and not to the currently configured one.
The bug is visible only in standalone ports mode, because when the port
is bridged, the issue is masked by .port_stp_state_set which overwrites
the address learning state to the proper value.

Fixes: 4d942354 ("net: dsa: sja1105: offload bridge port flags to device")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes references to uninitialized variables and
debugfs entry name for CN10K platform and HW_TSO flag check.

Fixes: 3ad3f8f9 ("octeontx2-af: cn10k: MAC internal loopback support").
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>

v1-v2
- Clear HW_TSO flag for 96xx B0 version.

This patch fixes the bug introduced by the commit
3ad3f8f9 ("octeontx2-af: cn10k: MAC internal loopback support").
These changes are not yet merged into net branch, hence submitting
to net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>

If the driver fails to probe, it would be nice to not leak memory.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ocelot_init_port is called only if dsa_is_unused_port == false, however
ocelot_deinit_port is called unconditionally. This causes a warning in
the skb_queue_purge inside ocelot_deinit_port saying that the spin lock
protecting ocelot_port->tx_skbs was not initialized.

Fixes: e5fb512d ("net: mscc: ocelot: deinitialize only initialized ports")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the 'ionic_reset_cb' typedef as it is not used.
Signed-off-by: Chen Lin <chen.lin5@zte.com.cn>
Acked-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf-next 2021-02-16

The following pull-request contains BPF updates for your *net-next* tree.

There's a small merge conflict between 7eeba170 ("tcp: Add receive timestamp
support for receive zerocopy.") from net-next tree and 9cacf81f ("bpf: Remove
extra lock_sock for TCP_ZEROCOPY_RECEIVE") from bpf-next tree. Resolve as follows:

  [...]
                lock_sock(sk);
                err = tcp_zerocopy_receive(sk, &zc, &tss);
                err = BPF_CGROUP_RUN_PROG_GETSOCKOPT_KERN(sk, level, optname,
                                                          &zc, &len, err);
                release_sock(sk);
  [...]

We've added 116 non-merge commits during the last 27 day(s) which contain
a total of 156 files changed, 5662 insertions(+), 1489 deletions(-).

The main changes are:

1) Adds support of pointers to types with known size among global function
   args to overcome the limit on max # of allowed args, from Dmitrii Banshchikov.

2) Add bpf_iter for task_vma which can be used to generate information similar
   to /proc/pid/maps, from Song Liu.

3) Enable bpf_{g,s}etsockopt() from all sock_addr related program hooks. Allow
   rewriting bind user ports from BPF side below the ip_unprivileged_port_start
   range, both from Stanislav Fomichev.

4) Prevent recursion on fentry/fexit & sleepable programs and allow map-in-map
   as well as per-cpu maps for the latter, from Alexei Starovoitov.

5) Add selftest script to run BPF CI locally. Also enable BPF ringbuffer
   for sleepable programs, both from KP Singh.

6) Extend verifier to enable variable offset read/write access to the BPF
   program stack, from Andrei Matei.

7) Improve tc & XDP MTU handling and add a new bpf_check_mtu() helper to
   query device MTU from programs, from Jesper Dangaard Brouer.

8) Allow bpf_get_socket_cookie() helper also be called from [sleepable] BPF
   tracing programs, from Florent Revest.

9) Extend x86 JIT to pad JMPs with NOPs for helping image to converge when
   otherwise too many passes are required, from Gary Lin.

10) Verifier fixes on atomics with BPF_FETCH as well as function-by-function
    verification both related to zero-extension handling, from Ilya Leoshkevich.

11) Better kernel build integration of resolve_btfids tool, from Jiri Olsa.

12) Batch of AF_XDP selftest cleanups and small performance improvement
    for libbpf's xsk map redirect for newer kernels, from Björn Töpel.

13) Follow-up BPF doc and verifier improvements around atomics with
    BPF_FETCH, from Brendan Jackman.

14) Permit zero-sized data sections e.g. if ELF .rodata section contains
    read-only data from local variables, from Yonghong Song.

15) veth driver skb bulk-allocation for ndo_xdp_xmit, from Lorenzo Bianconi.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Jefferson Carpenter <jeffersoncarpenter2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable mfs_max is not initialized and is being compared to find
the maximum value. Fix this by initializing it to 0.

Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 90bc8e00 ("i40e: Add hardware configuration for software based DCB")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Some internal PHY's have their events like link change reported by the
MAC interrupt. We have PHY_IGNORE_INTERRUPT to deal with this scenario.
I'm not too happy with this name. We don't ignore interrupts, typically
there is no interrupt exposed at a PHY level. So let's rename it to
PHY_MAC_INTERRUPT. This is in line with phy_mac_interrupt(), which is
called from the MAC interrupt handler to handle PHY events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

AR8035 recently gained MDIX support. The same functions will work for
the AR8031/33 PHY. We just need to add the at803x_config_aneg()
callback.

This was tested on a Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: broadcom: Cleanups and APD

This patch series cleans up the brcmphy.h header and its numerous unused
phydev->dev_flags, fixes the RXC/TXC clock disabling bit and allows the
BCM54210E PHY to utilize APD.

Changes in v2:

- dropped the patch that attempted to fix a possible discrepancy between
  the datasheet and the actual hardware
- added a patch to remove a forward declaration
- do additional flags cleanup
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

BCM54210E/BCM50212E has been verified to work correctly with the
auto-power down configuration done by bcm54xx_adjust_rxrefclk(), add it
to the list of PHYs working.

While we are at it, provide an appropriate name for the bit we are
changing which disables the RXC and TXC during auto-power down when
there is no energy on the cable.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We have a number of unused flags defined today and since we are scarce
on space and may need to introduce new flags in the future remove and
shift every existing flag down into a contiguous assignment.
PHY_BCM_FLAGS_MODE_1000BX was only used internally for the BCM54616S
PHY, so we allocate a driver private structure instead to store that
flag instead of canibalizing one from phydev->dev_flags for that
purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid a forward declaration by moving the callers of
bcm54xx_config_clock_delay() below its body.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The CRQ and subCRQ descriptors are DMA mapped, so dma_wmb(),
though weaker, is good enough to protect the data structures.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Acked-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only thing reset_long_term_buff() should do is set
buffer to zero. After doing that, it is not necessary to
send_request_map again to VIOS since it actually does not
change the mapping. So, keep memset function and remove all
others.
Signed-off-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add mptcpi_local_addr_used and mptcpi_local_addr_max in struct mptcp_info.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It seems that the right argument to be passed is &tcp_ip6_spec->ip6dst,
not &tcp_ip6_spec->ip6src, when calling function ipv6_addr_any().

Addresses-Coverity-ID: 1501734 ("Copy-paste error")
Fixes: efca91e8 ("i40e: Add flow director support for IPv6")
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hardware comes up with default max frame size set to 1518. When using it
with switch it results in actual Ethernet MTU 1492:
1518 - 14 (Ethernet header) - 4 (Broadcom's tag) - 4 (802.1q) - 4 (FCS)

Above means hardware in its default state can't handle standard Ethernet
traffic (MTU 1500).

Define maximum possible Ethernet overhead and always set MAC max frame
length accordingly. This change fixes handling Ethernet frames of length
1506 - 1514.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nobuhiro Iwamatsu says:

====================
net: stmmac: Add Toshiba Visconti SoCs glue driver

This series is the ethernet driver for Toshiba's ARM SoC, Visconti[0].
This provides DT binding documentation, device driver, MAINTAINER files,
and updates to DT files.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the ethernet controller node in Toshiba Visconti5 SoC-specific DT file.
And enable this node in TMPV7708 RM main board's board-specific DT file.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add entries for Toshiba Visconti ethernet controller binding and driver.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dwmac-visconti to the stmmac driver in Toshiba Visconti ARM SoCs.
This patch contains only the basic function of the device. There is no
clock control, PM, etc. yet. These will be added in the future.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add device tree bindings for ethernet controller of Toshiba Visconti
TMPV7700 SoC series.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>