- 08 Jan, 2018 26 commits
-
-
Lorenzo Bianconi authored
Move duplicated i2c/spi probe code in hts221_probe() Signed-off-by:
Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Stefan Tatschner authored
This patch affects BME280 and BMP280. The readout of the calibration data is moved to the probe function. Each sensor data access triggered reading the full calibration data before this patch. According to the datasheet, Section 4.4.2., the calibration data is stored in non-volatile memory. Since the calibration data does not change, and cannot be changed by the user, we can reduce bus traffic by reading the calibration data once. Additionally, proper organization of the data types enables removing some odd casts in the compensation formulas. Signed-off-by:
Stefan Tatschner <stefan.tatschner@gmail.com> Tested-by:
Andreas Klinger <ak@it-klinger.de> Signed-off-by:
-
Stefan Brüns authored
Currently, the registers are read out once per conversion interval. If the reading is delayed as the conversion has not yet finished, this extra time is treated as being part of the readout, although it should delay the start of the poll interval. This results in the interval starting slightly earlier in each iteration, until all time between reads is spent polling the status registers instead of sleeping. To fix this, the delay has to account for the state of the conversion ready flag. Whenever the conversion is already finished, schedule the next read on the regular interval, otherwise schedule it one interval after the flag bit has been set. Split the work function in two functions, one for the status poll and one for reading the values, to be able to note down the time when the flag bit is raised. Signed-off-by:
Stefan Brüns <stefan.bruens@rwth-aachen.de> Signed-off-by:
-
Stefan Brüns authored
As the timestamp is no longer (ab-)used to measure the function run time, it can be taken at the correct time, i.e. when the conversion has finished. Signed-off-by:
-
Stefan Brüns authored
The iio timestamp clock is user selectable and may be non-monotonic. Also, only part of the acquisition time is measured, thus the delay was longer than intended. Use a monotonic timestamp to track the time for the next poll iteration. The timestamp is advanced by the sampling interval each iteration. In case the conversion overrruns the register readout (i.e. fast sampling combined with a slow bus), one or multiple samples will be dropped. Signed-off-by:
-
Tobin C. Harding authored
When building kernel documentation sphinx emits the following warnings No description found for parameter 'iio_dev' Excess function parameter 'indio_dev' description in 'iio_device_register' These warnings are caused by a macro with a different argument identifier to the one listed in the kernel-docs. Change macro argument to be the same as the docs. Signed-off-by:
Tobin C. Harding <me@tobin.cc> Signed-off-by:
-
Maciej Purski authored
Calibration register is used for calculating current register in hardware according to datasheet: current = shunt_volt * calib_register / 2048 (ina 226) current = shunt_volt * calib_register / 4096 (ina 219) Fix calib_register value to 2048 for ina226 and 4096 for ina 219 in order to avoid truncation error and provide best precision allowed by shunt_voltage measurement. Make current scale value follow changes of shunt_resistor from sysfs as calib_register value is now fixed. Power_lsb value should also follow shunt_resistor changes as stated in datasheet: power_lsb = 25 * current_lsb (ina 226) power_lsb = 20 * current_lsb (ina 219) This is a part of the patchset: https://lkml.org/lkml/2017/11/22/394Signed-off-by:
Maciej Purski <m.purski@samsung.com> Reviewed-by:
-
Ji-Hun Kim authored
Clean up checkpatch warning: CHECK: Unnecessary parentheses around 'st->devid != ID_AD7195' Signed-off-by:
Ji-Hun Kim <jihuun.k@gmail.com> Signed-off-by:
-
Venkat Prashanth B U authored
This is a patch to the at91_adc.c file that fixes up a brace warning found by the checkpatch.pl tool Signed-off-by:
Venkat Prashanth B U <venkat.prashanth2498@gmail.com> Signed-off-by:
-
Andreas Klinger authored
Return value in hx711_reset() should indicate status of dout otherwise the calling function is reporting an error as false positive If there are two reads too close to each other, then the second one will never succeed. This happens especially when using buffered mode with both channels enabled. When changing the channel on every trigger event the former 100 ms are not enough for waiting until the device indicates normal mode. Wait up to 1 second until the device turns into normal mode. Signed-off-by:
-
Andreas Klinger authored
Add buffer to device data struct and add trigger function Data format is quite simple: voltage - channel 0 32 Bit voltage - channel 1 32 Bit timestamp 64 Bit Using both channels at the same time is working quite slow because of changing the channel which needs a dummy read. Signed-off-by: -
Stefan Brüns authored
The conversion time can be up to 16 seconds (8 ms per channel, 2 channels, 1024 times averaging). Signed-off-by:
-
Stefan Brüns authored
Although the datasheet states the CNVR flag is cleared by reading the BUS_VOLTAGE register, it is actually cleared by reading any of the voltage/current/power registers. The behaviour has been confirmed by TI support: http://e2e.ti.com/support/amplifiers/current-shunt-monitors/f/931/p/647053/2378282Signed-off-by:
-
Stefan Brüns authored
The timestamp is inserted into the buffer after the sample data by iio_push_to_buffers_with_timestamp, document the space requirement for the timestamp. Signed-off-by:
-
Stefan Brüns authored
iio_push_to_buffers_with_timestamp expects a void pointer, so the cast is both unnecessary and misleading. Signed-off-by:
-
Martin Blumenstingl authored
On some Meson8 devices the channel muxes are not programmed. This results in garbage values when trying to read channels that are not set up. Fix this by initializing the channel 0 and 1 muxes in MESON_SAR_ADC_CHAN_10_SW as well as the muxes for all other channels in MESON_SAR_ADC_AUX_SW based on what the vendor driver does (which is simply a 1:1 mapping of channel number and channel mux). This only showed up on Meson8 devices, because for GXBB and newer BL30 is taking care of initializing the channel muxes. This additionally fixes a typo in the MESON_SAR_ADC_AUX_SW_MUX_SEL_CHAN_MASK macro because the old definition assumed that the register fields were 2 bit wide, while they are actually 3 bit wide. Signed-off-by:
Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by:
-
Martin Blumenstingl authored
GX SoCs use a 1.2 MHz ADC clock, while the older SoCs use a 1.14 MHz clock. A comment in the driver from Amlogic's GPL kernel says that it's running at 1.28 MHz. However, it's actually programming a divider of 20 + 1. With a XTAL clock of 24 MHz this results in a frequency of 1.14 MHz. (their calculation might be based on a 27 MHz XTAL clock, but this is not what we have on the Meson8 and Meson8b SoCs). The ADC was still working with the 1.2MHz clock. In my own tests I did not see a difference between 1.2 and 1.14 MHz (regardless of the clock frequency used, the ADC results were identical). Signed-off-by:
-
Linus Walleij authored
The name of the file is "current_timetamp_clock" not "timestamp_clock". Fixes: bc2b7dab ("iio:core: timestamping clock selection support") Cc: Gregor Boirie <gregor.boirie@parrot.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Pravin Shedge authored
These duplicate includes have been found with scripts/checkincludes.pl but they have been removed manually to avoid removing false positives. Signed-off-by:
Pravin Shedge <pravin.shedge4linux@gmail.com> Signed-off-by:
-
Andrew F. Davis authored
Found with scripts/coccinelle/misc/boolconv.cocci. Signed-off-by:
Andrew F. Davis <afd@ti.com> Signed-off-by:
-
Benjamin Gaignard authored
Add SPDX identifier in stm32's files in IIO directory Signed-off-by:
Benjamin Gaignard <benjamin.gaignard@st.com> Acked-by:
Fabrice Gasnier <fabrice.gasnier@st.com> Acked-by:
Philippe Ombredanne <pombredanne@nexb.com> Signed-off-by:
-
Colin Ian King authored
Structures st_uvis25_i2c_regmap_config and st_uvis25_spi_regmap_config are local to the source and do not need to be in global scope, so make them both static. Cleans up sparse warnings: warning: symbol 'st_uvis25_i2c_regmap_config' was not declared. Should it be static? warning: symbol 'st_uvis25_spi_regmap_config' was not declared. Should it be static? Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Matt Fornero authored
Add a sysfs attribute that exposes buffer data available to userspace. This attribute can be checked at runtime to determine the overall buffer fill level (across all allocated buffers). Signed-off-by:
Matt Fornero <matt.fornero@mathworks.com> Signed-off-by:
-
Martin Kepplinger authored
This replaces the custom license information text with the appropriate SPDX identifier. While the information here stays the same, it is easier to read. Signed-off-by:
Martin Kepplinger <martink@posteo.de> Acked-by:
Peter Meerwald-Stadler <pmeerw@pmeerw.net> Acked-by:
Harinath Nampally <harinath922@gmail.com> Signed-off-by:
-
Arnd Bergmann authored
getnstimeofday() suffers from the overflow in y2038 on 32-bit architectures and requires a conversion into the nanosecond format that we want here. This changes ssp_parse_dataframe() to use ktime_get_real_ns() directly, which does not have that problem. An open question is what time base should be used here. Normally timestamps should use ktime_get_ns() or ktime_get_boot_ns() to read monotonic time instead of "real" time, which suffers from time jumps due to settimeofday() calls or leap seconds. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Bartosz Golaszewski authored
As discussed with Marc Zyngier: irq_sim_init() and its devres variant should return the base of the allocated interrupt range on success rather than 0. This will be modified later - first, change the way users handle the return value of these routines. Signed-off-by:
Bartosz Golaszewski <brgl@bgdev.pl> Signed-off-by:
-
- 02 Jan, 2018 1 commit
-
-
Greg Kroah-Hartman authored
We need the staging fixes in here as well. Signed-off-by:
-
- 31 Dec, 2017 13 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "A couple of fixlets for x86: - Fix the ESPFIX double fault handling for 5-level pagetables - Fix the commandline parsing for 'apic=' on 32bit systems and update documentation - Make zombie stack traces reliable - Fix kexec with stack canary - Fix the delivery mode for APICs which was missed when the x86 vector management was converted to single target delivery. Caused a regression due to the broken hardware which ignores affinity settings in lowest prio delivery mode. - Unbreak modules when AMD memory encryption is enabled - Remove an unused parameter of prepare_switch_to" * 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/apic: Switch all APICs to Fixed delivery mode x86/apic: Update the 'apic=' description of setting APIC driver x86/apic: Avoid wrong warning when parsing 'apic=' in X86-32 case x86-32: Fix kexec with stack canary (CONFIG_CC_STACKPROTECTOR) x86: Remove unused parameter of prepare_switch_to x86/stacktrace: Make zombie stack traces reliable x86/mm: Unbreak modules that use the DMA API x86/build: Make isoimage work on Debian x86/espfix/64: Fix espfix double-fault handling on 5-level systems -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 page table isolation fixes from Thomas Gleixner: "Four patches addressing the PTI fallout as discussed and debugged yesterday: - Remove stale and pointless TLB flush invocations from the hotplug code - Remove stale preempt_disable/enable from __native_flush_tlb() - Plug the memory leak in the write_ldt() error path" * 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/ldt: Make LDT pgtable free conditional x86/ldt: Plug memory leak in error path x86/mm: Remove preempt_disable/enable() from __native_flush_tlb() x86/smpboot: Remove stale TLB flush invocations -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull timer fixes from Thomas Gleixner: "A pile of fixes for long standing issues with the timer wheel and the NOHZ code: - Prevent timer base confusion accross the nohz switch, which can cause unlocked access and data corruption - Reinitialize the stale base clock on cpu hotplug to prevent subtle side effects including rollovers on 32bit - Prevent an interrupt storm when the timer softirq is already pending caused by tick_nohz_stop_sched_tick() - Move the timer start tracepoint to a place where it actually makes sense - Add documentation to timerqueue functions as they caused confusion several times now" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: timerqueue: Document return values of timerqueue_add/del() timers: Invoke timer_start_debug() where it makes sense nohz: Prevent a timer interrupt storm in tick_nohz_stop_sched_tick() timers: Reinitialize per cpu bases on hotplug timers: Use deferrable base independent of base::nohz_active -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull smp fixlet from Thomas Gleixner: "A trivial build warning fix for newer compilers" * 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: cpu/hotplug: Move inline keyword at the beginning of declaration
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler fixes from Thomas Gleixner: "Three patches addressing the fallout of the CPU_ISOLATION changes especially with NO_HZ_FULL plus documentation of boot parameter dependency" * 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/isolation: Document boot parameters dependency on CONFIG_CPU_ISOLATION=y sched/isolation: Enable CONFIG_CPU_ISOLATION=y by default sched/isolation: Make CONFIG_NO_HZ_FULL select CONFIG_CPU_ISOLATION
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Thomas Gleixner: - plug a memory leak in the intel pmu init code - clang fixes - tooling fix to avoid including kernel headers - a fix for jvmti to generate correct debug information for inlined code - replace backtick with a regular shell function - fix the build in hardened environments * 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/x86/intel: Plug memory leak in intel_pmu_init() x86/asm: Allow again using asm.h when building for the 'bpf' clang target tools arch s390: Do not include header files from the kernel sources perf jvmti: Generate correct debug information for inlined code perf tools: Fix up build in hardened environments perf tools: Use shell function for perl cflags retrieval
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull irq fixes from Thomas Gleixner: "A rather large update after the kaisered maintainer finally found time to handle regression reports. - The larger part addresses a regression caused by the x86 vector management rework. The reservation based model does not work reliably for MSI interrupts, if they cannot be masked (yes, yet another hw engineering trainwreck). The reason is that the reservation mode assigns a dummy vector when the interrupt is allocated and switches to a real vector when the interrupt is requested. If the MSI entry cannot be masked then the initialization might raise an interrupt before the interrupt is requested, which ends up as spurious interrupt and causes device malfunction and worse. The fix is to exclude MSI interrupts which do not support masking from reservation mode and assign a real vector right away. - Extend the extra lockdep class setup for nested interrupts with a class for the recently added irq_desc::request_mutex so lockdep can differeniate and does not emit false positive warnings. - A ratelimit guard for the bad irq printout so in case a bad irq comes back immediately the system does not drown in dmesg spam" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq/msi, x86/vector: Prevent reservation mode for non maskable MSI genirq/irqdomain: Rename early argument of irq_domain_activate_irq() x86/vector: Use IRQD_CAN_RESERVE flag genirq: Introduce IRQD_CAN_RESERVE flag genirq/msi: Handle reactivation only on success gpio: brcmstb: Make really use of the new lockdep class genirq: Guard handle_bad_irq log messages kernel/irq: Extend lockdep class for request mutex -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull objtool fixes from Thomas Gleixner: "Three fixlets for objtool: - Address two segfaults related to missing parameter and clang objects - Make it compile clean with clang" * 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: objtool: Fix seg fault with clang-compiled objects objtool: Fix seg fault caused by missing parameter objtool: Fix Clang enum conversion warning -
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-miscLinus Torvalds authored
Pull char/misc fixes from Greg KH: "Here are six small fixes of some of the char/misc drivers that have been sent in to resolve reported issues. Nothing major, a binder use-after-free fix, some thunderbolt bugfixes, a hyper-v bugfix, and an nvmem driver fix. All of these have been in linux-next with no reported issues for a while" * tag 'char-misc-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: nvmem: meson-mx-efuse: fix reading from an offset other than 0 binder: fix proc->files use-after-free vmbus: unregister device_obj->channels_kset thunderbolt: Mask ring interrupt properly when polling starts MAINTAINERS: Add thunderbolt.rst to the Thunderbolt driver entry thunderbolt: Make pathname to force_power shorter
-
Linus Torvalds authored
Merge tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core fixes from Greg KH: "Here are two driver core fixes for 4.15-rc6, resolving some reported issues. The first is a cacheinfo fix for DT based systems to resolve a reported issue that has been around for a while, and the other is to resolve a regression in the kobject uevent code that showed up in 4.15-rc1. Both have been in linux-next for a while with no reported issues" * tag 'driver-core-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: kobject: fix suppressing modalias in uevents delivered over netlink drivers: base: cacheinfo: fix cache type for non-architected system cache
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/stagingLinus Torvalds authored
Pull staging fixes from Greg KH: "Here are three staging driver fixes for 4.15-rc6 The first resolves a bug in the lustre driver that came about due to a broken cleanup patch, due to crazy list usage in that codebase. The remaining two are ion driver fixes, finally getting the CMA interaction to work properly, resolving two regressions in that area of the code. All have been in linux-next with no reported issues for a while" * tag 'staging-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: android: ion: Fix dma direction for dma_sync_sg_for_cpu/device staging: ion: Fix ion_cma_heap allocations staging: lustre: lnet: Fix recent breakage from list_for_each conversion
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/ttyLinus Torvalds authored
Pull TTY fix from Greg KH: "Here is a single tty fix for a reported issue that you wrote the patch for :) It's been in linux-next for a week or so with no reported issues" * tag 'tty-4.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: n_tty: fix EXTPROC vs ICANON interaction with TIOCINQ (aka FIONREAD)
-
