- 03 Feb, 2012 40 commits
-
-
Preston Fick authored
commit 7f482fc8 upstream. This fix changes the way baudrates are set on the CP210x devices from Silicon Labs. The CP2101/2/3 will respond to both a GET/SET_BAUDDIV command, and GET/SET_BAUDRATE command, while CP2104 and higher devices only respond to GET/SET_BAUDRATE. The current cp210x.ko driver in kernel version 3.2.0 only implements the GET/SET_BAUDDIV command. This patch implements the two new codes for the GET/SET_BAUDRATE commands. Then there is a change in the way that the baudrate is assigned or retrieved. This is done according to the CP210x USB specification in AN571. This document can be found here: http://www.silabs.com/pages/DownloadDoc.aspx?FILEURL=Support%20Documents/TechnicalDocs/AN571.pdf&src=DocumentationWebPart Sections 5.3/5.4 describe the USB packets for the old baudrate method. Sections 5.5/5.6 describe the USB packets for the new method. This patch also implements the new request scheme, and eliminates the unnecessary baudrate calculations since it uses the "actual baudrate" method. This patch solves the problem reported for the CP2104 in bug 42586, and also keeps support for all other devices (CP2101/2/3). This patchfile is also attached to the bug report on bugzilla.kernel.org. This patch has been developed and test on the 3.2.0 mainline kernel version under Ubuntu 10.11. Signed-off-by:
Preston Fick <preston.fick@silabs.com> [duplicate patch also sent by Johan - gregkh] Signed-off-by:
Johan Hovold <jhovold@gmail.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
commit 55b2afbb upstream. Make sure port is fully initialised before calling generic open. Signed-off-by:
-
Renato Caldas authored
commit 791b7d7c upstream. This device is a Oscilloscope/Logic Analizer/Pattern Generator/TDR, using a Silabs CP2103 USB to UART Bridge. Signed-off-by:
Renato Caldas <rmsc@fe.up.pt> Signed-off-by:
-
shawnlu authored
[ Upstream commit 8a622e71 ] md5 key is added in socket through remote address. remote address should be used in finding md5 key when sending out reset packet. Signed-off-by:
shawnlu <shawn.lu@ericsson.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Neal Cardwell authored
[ Upstream commit 5b35e1e6 ] This commit fixes tcp_trim_head() to recalculate the number of segments in the skb with the skb's existing MSS, so trimming the head causes the skb segment count to be monotonically non-increasing - it should stay the same or go down, but not increase. Previously tcp_trim_head() used the current MSS of the connection. But if there was a decrease in MSS between original transmission and ACK (e.g. due to PMTUD), this could cause tcp_trim_head() to counter-intuitively increase the segment count when trimming bytes off the head of an skb. This violated assumptions in tcp_tso_acked() that tcp_trim_head() only decreases the packet count, so that packets_acked in tcp_tso_acked() could underflow, leading tcp_clean_rtx_queue() to pass u32 pkts_acked values as large as 0xffffffff to ca_ops->pkts_acked(). As an aside, if tcp_trim_head() had really wanted the skb to reflect the current MSS, it should have called tcp_set_skb_tso_segs() unconditionally, since a decrease in MSS would mean that a single-packet skb should now be sliced into multiple segments. Signed-off-by:
Neal Cardwell <ncardwell@google.com> Acked-by:
Nandita Dukkipati <nanditad@google.com> Acked-by:
Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by:
-
David S. Miller authored
[ Upstream commit efc3dbc3 ] rds_sock_info() triggers locking warnings because we try to perform a local_bh_enable() (via sock_i_ino()) while hardware interrupts are disabled (via taking rds_sock_lock). There is no reason for rds_sock_lock to be a hardware IRQ disabling lock, none of these access paths run in hardware interrupt context. Therefore making it a BH disabling lock is safe and sufficient to fix this bug. Reported-by:
Kumar Sanghvi <kumaras@chelsio.com> Reported-by:
Josh Boyer <jwboyer@gmail.com> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit d00a9dd2 ] Several problems fixed in this patch : 1) Target of the conditional jump in case a divide by 0 is performed by a bpf is wrong. 2) Must 'generate' the full function prologue/epilogue at pass=0, or else we can stop too early in pass=1 if the proglen doesnt change. (if the increase of prologue/epilogue equals decrease of all instructions length because some jumps are converted to near jumps) 3) Change the wrong length detection at the end of code generation to issue a more explicit message, no need for a full stack trace. Reported-by:
Phil Oester <kernel@linuxace.com> Signed-off-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
James Chapman authored
[ Upstream commit 68315801 ] When a packet is received on an L2TP IP socket (L2TPv3 IP link encapsulation), the l2tpip socket's backlog_rcv function calls xfrm4_policy_check(). This is not necessary, since it was called before the skb was added to the backlog. With CONFIG_NET_NS enabled, xfrm4_policy_check() will oops if skb->dev is null, so this trivial patch removes the call. This bug has always been present, but only when CONFIG_NET_NS is enabled does it cause problems. Most users are probably using UDP encapsulation for L2TP, hence the problem has only recently surfaced. EIP: 0060:[<c12bb62b>] EFLAGS: 00210246 CPU: 0 EIP is at l2tp_ip_recvmsg+0xd4/0x2a7 EAX: 00000001 EBX: d77b5180 ECX: 00000000 EDX: 00200246 ESI: 00000000 EDI: d63cbd30 EBP: d63cbd18 ESP: d63cbcf4 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Call Trace: [<c1218568>] sock_common_recvmsg+0x31/0x46 [<c1215c92>] __sock_recvmsg_nosec+0x45/0x4d [<c12163a1>] __sock_recvmsg+0x31/0x3b [<c1216828>] sock_recvmsg+0x96/0xab [<c10b2693>] ? might_fault+0x47/0x81 [<c10b2693>] ? might_fault+0x47/0x81 [<c1167fd0>] ? _copy_from_user+0x31/0x115 [<c121e8c8>] ? copy_from_user+0x8/0xa [<c121ebd6>] ? verify_iovec+0x3e/0x78 [<c1216604>] __sys_recvmsg+0x10a/0x1aa [<c1216792>] ? sock_recvmsg+0x0/0xab [<c105a99b>] ? __lock_acquire+0xbdf/0xbee [<c12d5a99>] ? do_page_fault+0x193/0x375 [<c10d1200>] ? fcheck_files+0x9b/0xca [<c10d1259>] ? fget_light+0x2a/0x9c [<c1216bbb>] sys_recvmsg+0x2b/0x43 [<c1218145>] sys_socketcall+0x16d/0x1a5 [<c11679f0>] ? trace_hardirqs_on_thunk+0xc/0x10 [<c100305f>] sysenter_do_call+0x12/0x38 Code: c6 05 8c ea a8 c1 01 e8 0c d4 d9 ff 85 f6 74 07 3e ff 86 80 00 00 00 b9 17 b6 2b c1 ba 01 00 00 00 b8 78 ed 48 c1 e8 23 f6 d9 ff <ff> 76 0c 68 28 e3 30 c1 68 2d 44 41 c1 e8 89 57 01 00 83 c4 0c Signed-off-by:
James Chapman <jchapman@katalix.com> Acked-by:
-
Jiri Bohac authored
[ Upstream commit b924551b ] bond_alb_init_slave() is called from bond_enslave() and sets the slave's MAC address. This is done differently for TLB and ALB modes. bond->alb_info.rlb_enabled is used to discriminate between the two modes but this flag may be uninitialized if the slave is being enslaved prior to calling bond_open() -> bond_alb_initialize() on the master. It turns out all the callers of alb_set_slave_mac_addr() pass bond->alb_info.rlb_enabled as the hw parameter. This patch cleans up the unnecessary parameter of alb_set_slave_mac_addr() and makes the function decide based on the bonding mode instead, which fixes the above problem. Reported-by:
Narendra K <Narendra_K@Dell.com> Signed-off-by:
Jiri Bohac <jbohac@suse.cz> Signed-off-by:
Jay Vosburgh <fubar@us.ibm.com> Signed-off-by:
-
Eric W. Biederman authored
[ Upstream commit 8a8ee9af ] caif is a subsystem and as such it needs to register with register_pernet_subsys instead of register_pernet_device. Among other problems using register_pernet_device was resulting in net_generic being called before the caif_net structure was allocated. Which has been causing net_generic to fail with either BUG_ON's or by return NULL pointers. A more ugly problem that could be caused is packets in flight why the subsystem is shutting down. To remove confusion also remove the cruft cause by inappropriately trying to fix this bug. With the aid of the previous patch I have tested this patch and confirmed that using register_pernet_subsys makes the failure go away as it should. Signed-off-by:
Eric W. Biederman <ebiederm@xmission.com> Acked-by:
Sjur Brændeland <sjur.brandeland@stericsson.com> Tested-by:
Sasha Levin <levinsasha928@gmail.com> Signed-off-by:
-
Eric W. Biederman authored
[ Upstream commit 5ee4433e ] By definition net_generic should never be called when it can return NULL. Fail conspicously with a BUG_ON to make it clear when people mess up that a NULL return should never happen. Recently there was a bug in the CAIF subsystem where it was registered with register_pernet_device instead of register_pernet_subsys. It was erroneously concluded that net_generic could validly return NULL and that net_assign_generic was buggy (when it was just inefficient). Hopefully this BUG_ON will prevent people to coming to similar erroneous conclusions in the futrue. Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 073862ba ] When a new net namespace is created, we should attach to it a "struct net_generic" with enough slots (even empty), or we can hit the following BUG_ON() : [ 200.752016] kernel BUG at include/net/netns/generic.h:40! ... [ 200.752016] [<ffffffff825c3cea>] ? get_cfcnfg+0x3a/0x180 [ 200.752016] [<ffffffff821cf0b0>] ? lockdep_rtnl_is_held+0x10/0x20 [ 200.752016] [<ffffffff825c41be>] caif_device_notify+0x2e/0x530 [ 200.752016] [<ffffffff810d61b7>] notifier_call_chain+0x67/0x110 [ 200.752016] [<ffffffff810d67c1>] raw_notifier_call_chain+0x11/0x20 [ 200.752016] [<ffffffff821bae82>] call_netdevice_notifiers+0x32/0x60 [ 200.752016] [<ffffffff821c2b26>] register_netdevice+0x196/0x300 [ 200.752016] [<ffffffff821c2ca9>] register_netdev+0x19/0x30 [ 200.752016] [<ffffffff81c1c67a>] loopback_net_init+0x4a/0xa0 [ 200.752016] [<ffffffff821b5e62>] ops_init+0x42/0x180 [ 200.752016] [<ffffffff821b600b>] setup_net+0x6b/0x100 [ 200.752016] [<ffffffff821b6466>] copy_net_ns+0x86/0x110 [ 200.752016] [<ffffffff810d5789>] create_new_namespaces+0xd9/0x190 net_alloc_generic() should take into account the maximum index into the ptr array, as a subsystem might use net_generic() anytime. This also reduces number of reallocations in net_assign_generic() Reported-by:
-
Bjørn Mork authored
commit 15699e6f upstream. The probe does not strictly require the USB_CDC_DMM_TYPE descriptor, which is a good thing as it makes the driver usable on non-conforming interfaces. A user could e.g. bind to it to a CDC ECM interface by using the new_id and bind sysfs files. But this would fail with a 0 buffer length due to the missing descriptor. Fix by defining a reasonable fallback size: The minimum device receive buffer size required by the CDC WMC standard, revision 1.1 Signed-off-by:
Bjørn Mork <bjorn@mork.no> Signed-off-by:
-
Bjørn Mork authored
commit 655e247d upstream. As it turns out, there was a mismatch between the allocated inbuf size (desc->bMaxPacketSize0, typically something like 64) and the length we specified in the URB (desc->wMaxCommand, typically something like 2048) Signed-off-by:
-
Bjørn Mork authored
commit 62aaf24d upstream. wdm_disconnect() waits for the mutex held by wdm_read() before calling wake_up_all(). This causes a deadlock, preventing device removal to complete. Do the wake_up_all() before we start waiting for the locks. Signed-off-by:
-
Vivien Didelot authored
commit 6edf3c30 upstream. When no platform data was supplied, returned error code was 0. Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by:
Guenter Roeck <guenter.roeck@ericsson.com> Signed-off-by:
-
Guenter Roeck authored
commit ad77c3e1 upstream. NCT6776F only supports pwm mode for pwm2 and pwm3. Return error if an attempt is made to set those pwm channels to DC mode. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Acked-by:
Jean Delvare <khali@linux-fr.org> Signed-off-by:
-
Jean Delvare authored
commit 86b2bbfd upstream. Properly clamp temperature limits set by the user. Without this fix, attempts to write temperature limits above the maximum supported by the chip (255 degrees Celsius) would arbitrarily and unexpectedly result in the limit being set to 0 degree Celsius. Signed-off-by:
-
Andiry Xu authored
commit cf840551 upstream. When a TD length mismatch is found during isoc TRB enqueue, it directly returns -EINVAL. However, isoc transfer is partially enqueued at this time, and the ring should be cleared. This should be backported to kernels as old as 2.6.36, which contain the commit 522989a2 "xhci: Fix failed enqueue in the middle of isoch TD." Signed-off-by:
Andiry Xu <andiry.xu@amd.com> Signed-off-by:
Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by:
-
Sarah Sharp authored
commit d0cd5d48 upstream. The xHCI hub port code gets passed a zero-based port number by the USB core. It then adds one to in order to find a device slot by port number and device speed by calling xhci_find_slot_id_by_port. That function clearly states it requires a one-based port number. The xHCI port status change event handler was using a zero-based port number that it got from find_faked_portnum_from_hw_portnum, not a one-based port number. This lead to the doorbells never being rung for a device after a resume, or worse, a different device with the same speed having its doorbell rung (which could lead to bad power management in the xHCI host controller). This patch should be backported to kernels as old as 2.6.39. Signed-off-by:
-
Julia Lawall authored
commit 2492c6e6 upstream. Add missing iounmap in error handling code, in a case where the function already preforms iounmap on some other execution path. A simplified version of the semantic match that finds this problem is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ expression e; statement S,S1; int ret; @@ e = \(ioremap\|ioremap_nocache\)(...) ... when != iounmap(e) if (<+...e...+>) S ... when any when != iounmap(e) *if (...) { ... when != iounmap(e) return ...; } ... when any iounmap(e); // </smpl> Signed-off-by:
Julia Lawall <Julia.Lawall@lip6.fr> Acked-by:
Alan Stern <stern@rowland.harvard.edu> Signed-off-by:
-
Harrison Metzger authored
commit 1097cceb upstream. This changes the max length for the usb seven segment delcom device to 8 from 6. Delcom has both 6 and 8 variants and having 8 works fine with devices which are only 6. Signed-off-by:
Harrison Metzger <harrisonmetz@gmail.com> Signed-off-by:
Stuart Pook <stuart@acm.org> Signed-off-by:
-
Ryan Mallon authored
commit bf9c05d5 upstream. The assignment of handle in vmw_framebuffer_create_handle doesn't actually do anything useful and is incorrectly assigning an integer value to a pointer argument. It appears that this is a typo and should be dereferencing handle rather than assigning to it directly. This fixes a bug where an undefined handle value is potentially returned to user-space. Signed-off-by:
Ryan Mallon <rmallon@gmail.com> Reviewed-by: Jakob Bornecrantz<jakob@vmware.com> Signed-off-by:
Dave Airlie <airlied@redhat.com> Signed-off-by:
-
Lucas Kannebley Tavares authored
commit 26aa38ca upstream. There was an error on the jsm driver that would cause it to be unable to recover after a second error is detected. At the first error, the device recovers properly: [72521.485691] EEH: Detected PCI bus error on device 0003:02:00.0 [72521.485695] EEH: This PCI device has failed 1 times in the last hour: ... [72532.035693] ttyn3 at MMIO 0x0 (irq = 49) is a jsm [72532.105689] jsm: Port 3 added However, at the second error, it cascades until EEH disables the device: [72631.229549] Call Trace: ... [72641.725687] jsm: Port 3 added [72641.725695] EEH: Detected PCI bus error on device 0003:02:00.0 [72641.725698] EEH: This PCI device has failed 3 times in the last hour: It was caused because the PCI state was not being saved after the first restore. Therefore, at the second recovery the PCI state would not be restored. Signed-off-by:
Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com> Signed-off-by:
Breno Leitao <brenohl@br.ibm.com> Acked-by:
Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com> Signed-off-by:
-
Rabin Vincent authored
commit ef605fdb upstream. Protect against pl011_console_write() and the interrupt for the console UART running concurrently on different CPUs. Otherwise the console_write could spin for a long time waiting for the UART to become not busy, while the other CPU continuously services UART interrupts and keeps the UART busy. The checks for sysrq and oops_in_progress are taken from 8250.c. Signed-off-by:
Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by:
Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Reviewed-by:
Bibek Basu <bibek.basu@stericsson.com> Reviewed-by:
Shreshtha Kumar Sahu <shreshthakumar.sahu@stericsson.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Jiri Slaby authored
commit 0eee50af upstream. Commit 74c21077 (serial: Use block_til_ready helper) and its fixup 3f582b8c (serial: fix termios settings in open) introduced a regression on UV systems. The serial eventually freezes while being used. It's completely unpredictable and sometimes needs a heap of traffic to happen first. To reproduce this, yast installation was used as it turned out to be pretty reliable in reproducing. Especially during installation process where one doesn't have an SSH daemon running. And no monitor as the HW is completely headless. So this was fun to find. Given the machine doesn't boot on vanilla before 2.6.36 final. (And the commits above are older.) Unless there is some bad race in the code, the hardware seems to be pretty broken. Otherwise pure MSR read should not cause such a bug, or? So to prevent the bug, revert to the old behavior. I.e. read modem status only if we really have to -- for non-CLOCAL set serials. Non-CLOCAL works on this hardware OK, I tried. See? I don't. And document that shit. Signed-off-by:
Jiri Slaby <jslaby@suse.cz> References: https://lkml.org/lkml/2011/12/6/573 References: https://bugzilla.novell.com/show_bug.cgi?id=718518Signed-off-by:
-
Eric W. Biederman authored
commit 6d443d84 upstream. Calling edge_remove_sysfs_attrs from edge_disconnect is too late as the device has already been removed from sysfs. Do the simple and obvious thing and make edge_remove_sysfs_attrs the port_remove method. Signed-off-by:
Wolfgang Frisch <wfpub@roembden.net> Signed-off-by:
-
Dan Williams authored
commit 074cc735 upstream. More ports we now know how to talk to. Signed-off-by:
Dan Williams <dcbw@redhat.com> Signed-off-by:
-
Bjørn Mork authored
commit e8537bd2 upstream. using a separate read and write mutex for locking is sufficient to make the driver accept simultaneous read and write. This improves useability a lot. Signed-off-by:
-
Bjørn Mork authored
commit c428b70c upstream. wdm_in_callback() will also touch this field, so we cannot change it without locking Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
Alan Cox authored
commit 2353f806 upstream. 0x04d8, 0x000a: Hornby Elite Signed-off-by:
Alan Cox <alan@linux.intel.com> Signed-off-by:
-
Peter Naulls authored
commit fc216ec3 upstream. I tested this against 2.6.39 in the Ubuntu kernel, however I see the IDs are not in latest 3.2 git. This adds IDs for the FTDI controller in the Rainforest Automation Zigbee dongle. Signed-off-by:
Peter Naulls <peter@chocky.org> Signed-off-by:
-
Peter Korsgaard authored
commit 55f13aea upstream. Port A for JTAG, port B for serial. Signed-off-by:
Peter Korsgaard <jacmet@sunsite.dk> Signed-off-by:
-
Johan Hovold authored
commit 108e02b1 upstream. Fix regression introduced by commit b1ffb4c8 ("USB: Fix Corruption issue in USB ftdi driver ftdi_sio.c") which caused the termios settings to no longer be initialised at open. Consequently it was no longer possible to set the port to the default speed of 9600 baud without first changing to another baud rate and back again. Reported-by:
Roland Ramthun <mail@roland-ramthun.de> Signed-off-by:
-
Johan Hovold authored
commit eb833a9e upstream. Return EINVAL if new baud_base does not match the current one. The baud_base is device specific and can not be changed. This restores the old (pre-2005) behaviour which was changed due to a misunderstanding regarding this fact (see https://lkml.org/lkml/2005/1/20/84). Reported-by:
Torbjörn Lofterud <torbjorn@pi.nxs.se> Signed-off-by:
-
Kentaro Matsuyama authored
commit e423d740 upstream. Add vendor and product ID for USB 3G/LTE modem of docomo L-02C Signed-off-by:
Kentaro Matsuyama <kentaro.matsuyama@gmail.com> Signed-off-by:
-
Will Deacon authored
commit 612539e8 upstream. On v7, we use the same cache maintenance instructions for data lines as for unified lines. This was not the case for v6, where HARVARD_CACHE was defined to indicate the L1 cache topology. This patch removes the erroneous compile-time check for HARVARD_CACHE in proc-v7.S, ensuring that we perform I-side invalidation at boot. Reported-and-Acked-by:
Shawn Guo <shawn.guo@linaro.org> Acked-by:
Catalin Marinas <Catalin.Marinas@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by:
-
Srinidhi KASAGAR authored
commit d65015f7 upstream. This applies ARM errata 764369 for all ux500 platforms. Signed-off-by:
-
Jonathan Nieder authored
commit f2c0d026 upstream. syslog-ng versions before 3.3.0beta1 (2011-05-12) assume that CAP_SYS_ADMIN is sufficient to access syslog, so ever since CAP_SYSLOG was introduced (2010-11-25) they have triggered a warning. Commit ee24aebf ("cap_syslog: accept CAP_SYS_ADMIN for now") improved matters a little by making syslog-ng work again, just keeping the WARN_ONCE(). But still, this is a warning that writes a stack trace we don't care about to syslog, sets a taint flag, and alarms sysadmins when nothing worse has happened than use of an old userspace with a recent kernel. Convert the WARN_ONCE to a printk_once to avoid that while continuing to give userspace developers a hint that this is an unwanted backward-compatibility feature and won't be around forever. Reported-by:
Ralf Hildebrandt <ralf.hildebrandt@charite.de> Reported-by:
Niels <zorglub_olsen@hotmail.com> Reported-by:
Paweł Sikora <pluto@agmk.net> Signed-off-by:
Jonathan Nieder <jrnieder@gmail.com> Liked-by:
Gergely Nagy <algernon@madhouse-project.org> Acked-by:
Serge Hallyn <serge@hallyn.com> Acked-by:
James Morris <jmorris@namei.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Cc: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de> Signed-off-by:
-
Paulo Zanoni authored
commit ba68e086 upstream. This is a revert of 81a14b46. We already set the mode polarity using the SDVO commands with struct intel_sdvo_dtd. We have at least 3 bugs that get fixed with this patch. The documentation, despite not clear, can also be interpreted in a way that suggests this patch is needed. Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=15766 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=42174 Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=43333Reviewed-by:
Eric Anholt <eric@anholt.net> Reviewed-by:
Jesse Barnes <jbarnes@virtuousgeek.org> Signed-off-by:
Paulo Zanoni <paulo.r.zanoni@intel.com> Signed-off-by:
Keith Packard <keithp@keithp.com> Signed-off-by:
-
