Merge branch 'topic/irq' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into wm8994-mfd

For later chip revisions the WM1811 GPIO6 register is always volatile so
store the device revision when initialising the driver and then check at
runtime if we're running on a newer device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

struct wm8994 includes a mutex so we need to include mutex.h before we
declare it. All current users rely on this being done implicitly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

The WM1811A is a variant of the WM1811 with pin configuration changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

As WM1811 revision C was transparent to software the revision IDs for
subsequent revisions are one less than they would normally be. Correct
for this in log messages.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

The driver has no need to modify the regulator_init_data so declare it
const to allow machine code to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

The different devices handled by the WM8994 can be distinguished using
their ID registers so we don't need to rely on the user having registered
the device correctly. Instead do the initial regmap setup with a minimal
configuration only supporting physical I/O and then configure the cache
once we have identified the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

As part of this we provide information about the registers that exist in
the device to the regmap core, drop the small amount of cache that the
core had been using and let regmap do the sync.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

Merge branch 'topic/cache' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap into HEAD

Describe the register map to the regmap core so that we can use its
diagnostic features and cache support.  This is split out from the patch
using it due to the size so that the actual code change is a bit clearer.

As the various devices are supersets of each other the access maps are
built up by layering the functions on top of each other, though the
interface for specifying the register defaults isn't currently amenable
to this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

Add a bunch of definitions for wm8994 registers that are not currently
used by software.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

Disable more pulls by default on WM8994 for a small current saving. Since
some designs do leave SPKMODE floating provide platform data to allow that
to be left enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

Add a placeholder device tree binding for the wm8994 driver. At present
the binding is essentially null as none of the platform data is supported,
and at least some of that will depend on the pending regulator bindings.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Oritz <sameo@linux.intel.com>

Allows devices to discover their own interrupt without having to remember
it themselves.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Sometimes the register map information may change in ways that drivers can
discover at runtime. For example, new revisions of a device may add new
registers. Support runtime discovery by drivers by allowing the register
cache to be reinitialised with a new function regmap_reinit_cache() which
discards the existing cache and creates a new one.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

While the IRQ core doesn't currently support shared threaded interrupts
that's no reason for drivers not to do their bit and report IRQ_NONE when
they don't get an interrupt. This allows the core spurious/wedget interrupt
detection support to do its thing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

* git://github.com/rustyrussell/linux:
  virtio-pci: make reset operation safer
  virtio-mmio: Correct the name of the guest features selector
  virtio: add HAS_IOMEM dependency to MMIO platform bus driver

virtio pci device reset actually just does an I/O
write, which in PCI is really posted, that is it
can complete on CPU before the device has received it.

Further, interrupts might have been pending on
another CPU, so device callback might get invoked after reset.

This conflicts with how drivers use reset, which is typically:
	reset
	unregister
a callback running after reset completed can race with
unregister, potentially leading to use after free bugs.

Fix by flushing out the write, and flushing pending interrupts.

This assumes that device is never reset from
its vq/config callbacks, or in parallel with being
added/removed, document this assumption.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Guest features selector spelling mistake.

Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

Fix this compile error on s390:

  CC [M]  drivers/virtio/virtio_mmio.o
drivers/virtio/virtio_mmio.c: In function 'vm_get_features':
drivers/virtio/virtio_mmio.c:107:2: error: implicit declaration of function 'writel'

Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>

* 'upstream-linus' of git://github.com/jgarzik/libata-dev:
  libata: fix build without BMDMA
  [libata] ahci_platform: fix DT probing

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
  PCI hotplug: shpchp: don't blindly claim non-AMD 0x7450 device IDs
  PCI: pciehp: wait 100 ms after Link Training check
  PCI: pciehp: wait 1000 ms before Link Training check
  PCI: pciehp: Retrieve link speed after link is trained
  PCI: Let PCI_PRI depend on PCI
  PCI: Fix compile errors with PCI_ATS and !PCI_IOV
  PCI / ACPI: Make acpiphp ignore root bridges using PCIe native hotplug

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Extend array bounds for all filename chars
  eCryptfs: Flush file in vma close
  eCryptfs: Prevent file create race condition

From mhalcrow's original commit message:

    Characters with ASCII values greater than the size of
    filename_rev_map[] are valid filename characters.
    ecryptfs_decode_from_filename() will access kernel memory beyond
    that array, and ecryptfs_parse_tag_70_packet() will then decrypt
    those characters. The attacker, using the FNEK of the crafted file,
    can then re-encrypt the characters to reveal the kernel memory past
    the end of the filename_rev_map[] array. I expect low security
    impact since this array is statically allocated in the text area,
    and the amount of memory past the array that is accessible is
    limited by the largest possible ASCII filename character.

This patch solves the issue reported by mhalcrow but with an
implementation suggested by Linus to simply extend the length of
filename_rev_map[] to 256. Characters greater than 0x7A are mapped to
0x00, which is how invalid characters less than 0x7A were previously
being handled.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reported-by: Michael Halcrow <mhalcrow@google.com>
Cc: stable@kernel.org

Dirty pages weren't being written back when an mmap'ed eCryptfs file was
closed before the mapping was unmapped. Since f_ops->flush() is not
called by the munmap() path, the lower file was simply being released.
This patch flushes the eCryptfs file in the vm_ops->close() path.

https://launchpad.net/bugs/870326Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Cc: stable@kernel.org [2.6.39+]

The file creation path prematurely called d_instantiate() and
unlock_new_inode() before the eCryptfs inode info was fully
allocated and initialized and before the eCryptfs metadata was written
to the lower file.

This could result in race conditions in subsequent file and inode
operations leading to unexpected error conditions or a null pointer
dereference while attempting to use the unallocated memory.

https://launchpad.net/bugs/813146Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Cc: stable@kernel.org

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
  ktest: Check parent options for iterated tests

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c: Make i2cdev_notifier_call static
  i2c: Delete ANY_I2C_BUS
  i2c: Fix device name for 10-bit slave address
  i2c-algo-bit: Generate correct i2c address sequence for 10-bit target

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
  regulator: TPS65910: Fix VDD1/2 voltage selector count

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
  drm: integer overflow in drm_mode_dirtyfb_ioctl()
  drivers/gpu/vga/vgaarb.c: add missing kfree
  drm/radeon/kms/atom: unify i2c gpio table handling
  drm/radeon/kms: fix up gpio i2c mask bits for r4xx for real
  ttm: Don't return the bo reserved on error path
  drm/radeon/kms: add a CS ioctl flag not to rewrite tiling flags in the CS
  drm/i915: Fix inconsistent backlight level during disabled
  drm, i915: Fix memory leak in i915_gem_busy_ioctl().
  drm/i915: Use DPCD value for max DP lanes.
  drm/i915: Initiate DP link training only on the lanes we'll be using
  drm/i915: Remove trailing white space
  drm/i915: Try harder during dp pattern 1 link training
  drm/i915: Make DP prepare/commit consistent with DP dpms
  drm/i915: Let panel power sequencing hardware do its job
  drm/i915: Treat PCH eDP like DP in most places
  drm/i915: Remove link_status field from intel_dp structure
  drm/i915: Move common PCH_PP_CONTROL setup to ironlake_get_pp_control
  drm/i915: Module parameters using '-1' as default must be signed type
  drm/i915: Turn on another required clock gating bit on gen6.
  drm/i915: Turn on a required 3D clock gating bit on Sandybridge.
  ...

Count of selector voltage is required for regulator_set_voltage
to work via set_voltage_sel. VDD1/2 currently have it as zero,
so regulator_set_voltage won't work for VDD1/2.
Update count (n_voltages) for VDD1/2.

Output Voltage = (step value * 12.5 mV + 562.5 mV) * gain

With above expr, number of voltages that can be selected is
step value count * gain count

constant for gain count will be called VDD1_2_NUM_VOLT_COARSE

existing constant for step value count is VDD1_2_NUM_VOLTS,
use VDD1_2_NUM_VOLT_FINE instead to make clear that step value
is not the only component in deciding selectable voltage count
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The function i2cdev_notifier_call is used only in i2c-dev file
making it static.
Also removes the following sparse warning

drivers/i2c/i2c-dev.c:582:5: warning: symbol 'i2cdev_notifier_call'
was not declared. Should it be static?
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Last piece of code using ANY_I2C_BUS was deleted almost 2 years ago,
so ANY_I2C_BUS can go away as well.
Signed-off-by: Jean Delvare <khali@linux-fr.org>

10-bit addresses overlap with traditional 7-bit addresses, leading in
device name collisions. Add an arbitrary offset to 10-bit addresses to
prevent this collision. The offset was chosen so that the address is
still easily recognizable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>

The wrong bits were put on the wire, fix that.

This fixes kernel bug #42562.
Signed-off-by: Sheng-Hui J. Chu <jeffchu@broadcom.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>

There is a potential integer overflow in drm_mode_dirtyfb_ioctl()
if userspace passes in a large num_clips.  The call to kmalloc would
allocate a small buffer, and the call to fb->funcs->dirty may result
in a memory corruption.
Reported-by: Haogang Chen <haogangchen@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>