Add MAINTAINERS entry for the Samsung USB2 PHY driver.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Add a MODULE_DEVICE_TABLE call for OF match tables. This allows the
module to be autoloaded based on devicetree information.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Commit 249751f2 ("usb: phy: twl4030-usb: poll for ID disconnect")
added twl4030_id_workaround_work() to deal with lost interrupts
after ID pin goes down. Looks like commit f1ddc24c ("usb: phy:
twl4030-usb: remove *set_suspend* and *phy_init* ops") changed
things around for the generic phy framework, and delayed work no
longer got called except initially during boot.

The PHY connect and disconnect interrupts for twl4030-usb are not
working after disconnecting a USB-A cable from the board, and the
deeper idle states for omap are blocked as the USB controller
stays busy.

The issue can be solved by calling delayed work from twl4030_usb_irq()
when ID pin is down and the PHY is not asleep like we already do
in twl4030_id_workaround_work().

But as both twl4030_usb_irq() and twl4030_id_workaround_work()
already do pretty much the same thing, let's call twl4030_usb_irq()
from twl4030_id_workaround_work() instead of adding some more
duplicate code. We also must call sysfs_notify() only when we have
an interrupt and not from the delayed work as notified by
Grazvydas Ignotas <notasas@gmail.com>.

Fixes: f1ddc24c ("usb: phy: twl4030-usb: remove *set_suspend* and *phy_init* ops")
Cc: stable@vger.kernel.org # v3.13+
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Commit 30a70b02 ("usb: musb: fix obex in g_nokia.ko causing kernel
panic") attempted to fix runtime PM handling for PHYs that are on the
I2C bus. Commit 3063a12b ("usb: musb: fix PHY power on/off") then
changed things around to enable of PHYs that rely on runtime PM.

These changes however broke idling of the PHY and causes at least
100 mW extra power consumption on omaps, which is a lot with
the idle power consumption being below 10 mW range on many devices.

As calling phy_power_on/off from runtime PM calls in the USB
causes complicated issues with I2C connected PHYs, let's just let
the PHY do it's own runtime PM as needed. This leaves out the
dependency between PHYs and USB controller drivers for runtime
PM.

Let's fix the regression for twl4030-usb by adding minimal runtime
PM support. This allows idling the PHY on disconnect.

Note that we are changing to use standard runtime PM handling
for twl4030_phy_init() as that function just checks the state
and does not initialize the PHY. The PHY won't get initialized
until in twl4030_phy_power_on().

Fixes: 30a70b02 ("usb: musb: fix obex in g_nokia.ko causing kernel panic")
Fixes: 3063a12b ("usb: musb: fix PHY power on/off")
Cc: stable@vger.kernel.org # v3.15+
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

Merge tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm fix from Thierry Reding:
 "Just one bugfix for the PWM lookup table code that would cause a PWM
  channel to be set to the wrong period and polarity for non-perfect
  matches"

* tag 'pwm/for-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: Fix period and polarity in pwm_get() for non-perfect matches

The new_ctx pointer is set only for non-chanctx drivers.  This yielded a
crash for chanctx-based drivers during channel switch finalization:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
  IP: ieee80211_vif_use_reserved_switch+0x71c/0xb00 [mac80211]

Use an adequate chanctx pointer to fix this.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull networking fixes from David Miller:
 "Here are some bug fixes that have piled up during ksummit/linuxcon.

   1) Fix endian problems in ibmveth, from Anton Blanchard.

   2) IPV6 routing code does GFP_KERNEL allocation in atomic, fix from
      Benjamin Block.

   3) SCTP association fixes from Daniel Borkmann.

   4) When multiple VLAN headers are present we have to make sure the
      second and subsequent ones are pullable in the SKB otherwise we
      blindly dereference garbage.  From Jiri Benc.

   5) The argument adjustment of the signature of hlist_add_after*()
      introduced a regression in the batman-adv code, fix from Sven
      Eckelmann.

   6) Fix TX hang handling to avoid a panic in i40e, from Anjali Singhai
      Jain.

   7) PTP flag test is inverted in i40e driver, from Jesse Brandeburg.

   8) ATM LEC driver needs to hold RTNL mutex over MTU changes, from
      Chas Williams.

   9) Truncate packets larger then the TPACKET_V3 format configured
      buffers, otherwise we overwrite past the end of said buffers.
      From Eric Dumazet.

  10) Fix endianness bugs in qlcnic firmware handling, from Rajesh
      Borundia and Shahed Shaikh.

  11) CXGB4 sometimes doesn't get all of the TX completion events it
      should resulting in SKBs getting stuck in the TX queue, from
      Hariprasad Shenai.

  12) When the FEC chip's PTP clock is disabled, you can't access the
      register.  Add necessary checks to avoid the resulting hang, from
      Fugang Duan"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
  drivers: isdn: eicon: xdi_msg.h: Fix typo in #ifndef
  net: sctp: fix suboptimal edge-case on non-active active/retrans path selection
  net: sctp: spare unnecessary comparison in sctp_trans_elect_best
  net: ethernet: broadcom: bnx2x: Remove redundant #ifdef
  ibmveth: Fix endian issues with rx_no_buffer statistic
  net: xgene: fix possible NULL dereference in xgene_enet_free_desc_rings()
  openvswitch: fix panic with multiple vlan headers
  net: ipv6: fib: don't sleep inside atomic lock
  net: fec: ptp: avoid register access when ipg clock is disabled
  cxgb4: Free completed tx skbs promptly
  cxgb4: Fix race condition in cleanup
  sctp: not send SCTP_PEER_ADDR_CHANGE notifications with failed probe
  bnx2x: Revert UNDI flushing mechanism
  qlcnic: Fix endianess issue in firmware load from file operation
  qlcnic: Fix endianess issue in FW dump template header
  qlcnic: Fix flash access interface to application
  MAINTAINERS: Add section for MRF24J40 IEEE 802.15.4 radio driver
  macvlan: Allow setting multicast filter on all macvlan types
  packet: handle too big packets for PACKET_V3
  MAINTAINERS: add entry for ec_bhf driver
  ...

Test for definedness of the macro which is actually defined (the
change is hard to see: it is s/SSS/SSA/).
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

In SCTP, selection of active (T.ACT) and retransmission (T.RET)
transports is being done whenever transport control operations
(UP, DOWN, PF, ...) are engaged through sctp_assoc_control_transport().

Commits 4c47af4d ("net: sctp: rework multihoming retransmission
path selection to rfc4960") and a7288c4d ("net: sctp: improve
sctp_select_active_and_retran_path selection") have both improved
it towards a more fine-grained and optimal path selection.

Currently, the selection algorithm for T.ACT and T.RET is as follows:

1) Elect the two most recently used ACTIVE transports T1, T2 for
   T.ACT, T.RET, where T.ACT<-T1 and T1 is most recently used
2) In case primary path T.PRI not in {T1, T2} but ACTIVE, set
   T.ACT<-T.PRI and T.RET<-T1
3) If only T1 is ACTIVE from the set, set T.ACT<-T1 and T.RET<-T1
4) If none is ACTIVE, set T.ACT<-best(T.PRI, T.RET, T3) where
   T3 is the most recently used (if avail) in PF, set T.RET<-T.PRI

Prior to above commits, 4) was simply a camp on T.ACT<-T.PRI and
T.RET<-T.PRI, ignoring possible paths in PF. Camping on T.PRI is
still slightly suboptimal as it can lead to the following scenario:

Setup:
        <A>                                <B>
    T1: p1p1 (10.0.10.10) <==>  .'`)  <==> p1p1 (10.0.10.12)  <= T.PRI
    T2: p1p2 (10.0.10.20) <==> (_ . ) <==> p1p2 (10.0.10.22)

    net.sctp.rto_min = 1000
    net.sctp.path_max_retrans = 2
    net.sctp.pf_retrans = 0
    net.sctp.hb_interval = 1000

T.PRI is permanently down, T2 is put briefly into PF state (e.g. due to
link flapping). Here, the first time transmission is sent over PF path
T2 as it's the only non-INACTIVE path, but the retransmitted data-chunks
are sent over the INACTIVE path T1 (T.PRI), which is not good.

After the patch, it's choosing better transports in both cases by
modifying step 4):

4) If none is ACTIVE, set T.ACT_new<-best(T.ACT_old, T3) where T3 is
   the most recently used (if avail) in PF, set T.RET<-T.ACT_new

This will still select a best possible path in PF if available (which
can also include T.PRI/T.RET), and set both T.ACT/T.RET to it.

In case sctp_assoc_control_transport() *just* put T.ACT_old into INACTIVE
as it transitioned from ACTIVE->PF->INACTIVE and stays in INACTIVE just
for a very short while before going back ACTIVE, it will guarantee that
this path will be reselected for T.ACT/T.RET since T3 (PF) is not
available.

Previously, this was not possible, as we would only select between T.PRI
and T.RET, and a possible T3 would be NULL due to the fact that we have
just transitioned T3 in sctp_assoc_control_transport() from PF->INACTIVE
and would select a suboptimal path when T.PRI/T.RET have worse properties.

In the case that T.ACT_old permanently went to INACTIVE during this
transition and there's no PF path available, plus T.PRI and T.RET are
INACTIVE as well, we would now camp on T.ACT_old, but if everything is
being INACTIVE there's really not much we can do except hoping for a
successful HB to bring one of the transports back up again and, thus
cause a new selection through sctp_assoc_control_transport().

Now both tests work fine:

Case 1:

 1. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

 2. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(PF)

 3. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(INACTIVE)

 5. T1 S(PF) T.ACT, T.RET
    T2 S(INACTIVE)

[ 5.1 T1 S(INACTIVE) T.ACT, T.RET
      T2 S(INACTIVE) ]

 6. T1 S(ACTIVE) T.ACT, T.RET
    T2 S(INACTIVE)

 7. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

Case 2:

 1. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET

 2. T1 S(PF)
    T2 S(ACTIVE) T.ACT, T.RET

 3. T1 S(INACTIVE)
    T2 S(ACTIVE) T.ACT, T.RET

 5. T1 S(INACTIVE)
    T2 S(PF) T.ACT, T.RET

[ 5.1 T1 S(INACTIVE)
      T2 S(INACTIVE) T.ACT, T.RET ]

 6. T1 S(INACTIVE)
    T2 S(ACTIVE) T.ACT, T.RET

 7. T1 S(ACTIVE) T.ACT
    T2 S(ACTIVE) T.RET
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When both transports are the same, we don't have to go down that
road only to realize that we will return the very same transport.
We are guaranteed that curr is always non-NULL. Therefore, just
short-circuit this special case.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Nothing defines _ASM_GENERIC_INT_L64_H, it is a weird way to check for
64 bit longs, and u64 should be printed using %llx anyway.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hidden away in the last 8 bytes of the buffer_list page is a solitary
statistic. It needs to be byte swapped or else ethtool -S will
produce numbers that terrify the user.

Since we do this in multiple places, create a helper function with a
comment explaining what is going on.
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

A NULL pointer dereference is possible for the argument ring->buf_pool
which is passed to xgene_enet_free_desc_ring(), as ring could be NULL.

And now since NULL pointers are being checked for before the calls to
xgene_enet_free_desc_ring(), might as well take advantage of them and
not call the function if the argument would be NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When there are multiple vlan headers present in a received frame, the first
one is put into vlan_tci and protocol is set to ETH_P_8021Q. Anything in the
skb beyond the VLAN TPID may be still non-linear, including the inner TCI
and ethertype. While ovs_flow_extract takes care of IP and IPv6 headers, it
does nothing with ETH_P_8021Q. Later, if OVS_ACTION_ATTR_POP_VLAN is
executed, __pop_vlan_tci pulls the next vlan header into vlan_tci.

This leads to two things:

1. Part of the resulting ethernet header is in the non-linear part of the
   skb. When eth_type_trans is called later as the result of
   OVS_ACTION_ATTR_OUTPUT, kernel BUGs in __skb_pull. Also, __pop_vlan_tci
   is in fact accessing random data when it reads past the TPID.

2. network_header points into the ethernet header instead of behind it.
   mac_len is set to a wrong value (10), too.
Reported-by: Yulong Pei <ypei@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The function fib6_commit_metrics() allocates a piece of memory in mode
GFP_KERNEL while holding an atomic lock from higher up in the stack, in
the function __ip6_ins_rt(). This produces the following BUG:

> BUG: sleeping function called from invalid context at mm/slub.c:1250
> in_atomic(): 1, irqs_disabled(): 0, pid: 2909, name: dhcpcd
> 2 locks held by dhcpcd/2909:
>  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff81978e67>] rtnl_lock+0x17/0x20
>  #1:  (&tb->tb6_lock){++--+.}, at: [<ffffffff81a6951a>] ip6_route_add+0x65a/0x800
> CPU: 1 PID: 2909 Comm: dhcpcd Not tainted 3.17.0-rc1 #1
> Hardware name: ASUS All Series/Q87T, BIOS 0216 10/16/2013
>  0000000000000008 ffff8800c8f13858 ffffffff81af135a 0000000000000000
>  ffff880212202430 ffff8800c8f13878 ffffffff810f8d3a ffff880212202c98
>  0000000000000010 ffff8800c8f138c8 ffffffff8121ad0e 0000000000000001
> Call Trace:
>  [<ffffffff81af135a>] dump_stack+0x4e/0x68
>  [<ffffffff810f8d3a>] __might_sleep+0x10a/0x120
>  [<ffffffff8121ad0e>] kmem_cache_alloc_trace+0x4e/0x190
>  [<ffffffff81a6bcd6>] ? fib6_commit_metrics+0x66/0x110
>  [<ffffffff81a6bcd6>] fib6_commit_metrics+0x66/0x110
>  [<ffffffff81a6cbf3>] fib6_add+0x883/0xa80
>  [<ffffffff81a6951a>] ? ip6_route_add+0x65a/0x800
>  [<ffffffff81a69535>] ip6_route_add+0x675/0x800
>  [<ffffffff81a68f2a>] ? ip6_route_add+0x6a/0x800
>  [<ffffffff81a6990c>] inet6_rtm_newroute+0x5c/0x80
>  [<ffffffff8197cf01>] rtnetlink_rcv_msg+0x211/0x260
>  [<ffffffff81978e67>] ? rtnl_lock+0x17/0x20
>  [<ffffffff81119708>] ? lock_release_holdtime+0x28/0x180
>  [<ffffffff81978e67>] ? rtnl_lock+0x17/0x20
>  [<ffffffff8197ccf0>] ? __rtnl_unlock+0x20/0x20
>  [<ffffffff819a989e>] netlink_rcv_skb+0x6e/0xd0
>  [<ffffffff81978ee5>] rtnetlink_rcv+0x25/0x40
>  [<ffffffff819a8e59>] netlink_unicast+0xd9/0x180
>  [<ffffffff819a9600>] netlink_sendmsg+0x700/0x770
>  [<ffffffff81103735>] ? local_clock+0x25/0x30
>  [<ffffffff8194e83c>] sock_sendmsg+0x6c/0x90
>  [<ffffffff811f98e3>] ? might_fault+0xa3/0xb0
>  [<ffffffff8195ca6d>] ? verify_iovec+0x7d/0xf0
>  [<ffffffff8194ec3e>] ___sys_sendmsg+0x37e/0x3b0
>  [<ffffffff8111ef15>] ? trace_hardirqs_on_caller+0x185/0x220
>  [<ffffffff81af979e>] ? mutex_unlock+0xe/0x10
>  [<ffffffff819a55ec>] ? netlink_insert+0xbc/0xe0
>  [<ffffffff819a65e5>] ? netlink_autobind.isra.30+0x125/0x150
>  [<ffffffff819a6520>] ? netlink_autobind.isra.30+0x60/0x150
>  [<ffffffff819a84f9>] ? netlink_bind+0x159/0x230
>  [<ffffffff811f989a>] ? might_fault+0x5a/0xb0
>  [<ffffffff8194f25e>] ? SYSC_bind+0x7e/0xd0
>  [<ffffffff8194f8cd>] __sys_sendmsg+0x4d/0x80
>  [<ffffffff8194f912>] SyS_sendmsg+0x12/0x20
>  [<ffffffff81afc692>] system_call_fastpath+0x16/0x1b

Fixing this by replacing the mode GFP_KERNEL with GFP_ATOMIC.
Signed-off-by: Benjamin Block <bebl@mageta.org>
Acked-by: David Rientjes <rientjes@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The current kernel hang on i.MX6SX with rootfs mount from MMC.
The root cause is that ptp uses a periodic timer to access enet register
even if ipg clock is disabled.

FEC ptp driver start one period timer to read 1588 counter register in the
ptp init function that is called after FEC driver is probed.

To save power, after FEC probe finish, FEC driver disable all clocks including
ipg clock that is needed for register access.

i.MX5x, i.MX6q/dl/sl FEC register access don't cause system hang when ipg clock
is disabled, just return zero value. But for i.MX6sx SOC, it cause system hang.

To avoid the issue, we need to check ptp clock status before ptp timer count access.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull arm64 fixes from Will Deacon:
 "This small set of fixes addresses a few issues introduced during the
  merge window, including:

   - fix typo in I-cache detection that was causing us to treat all
     I-caches as aliasing
   - hook up memfd_create and getrandom syscalls for native and compat
   - revert a temporary hack for defconfig builds in -next (the audit
     tree changes didn't make it in this merge window)
   - a couple of UEFI fixes for TEXT_OFFSET fuzzing and /memreserve/
   - a simple sparsemem fix for 48-bit physical addressing
   - small defconfig updates to get autotesters working with X-gene"

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  Revert "arm64: Do not invoke audit_syscall_* functions if !CONFIG_AUDIT_SYSCALL"
  arm64: mm: update max pa bits to 48
  arm64: ignore DT memreserve entries when booting in UEFI mode
  arm64: configs: Enable X-Gene SATA and ethernet in defconfig
  arm64: align randomized TEXT_OFFSET on 4 kB boundary
  asm-generic: add memfd_create system call to unistd.h
  arm64: compat: wire up memfd_create and getrandom syscalls for aarch32
  arm64: fix typo in I-cache policy detection

Pull IOMMU fixes from Joerg Roedel:
 "The fixes include:

   - fix a crash in the VT-d driver when devices with a driver attached
     are hot-unplugged

   - fix a AMD IOMMU driver crash with device assignment of 32 bit PCI
     devices to KVM guests

   - fix for a copy&paste error in generic IOMMU code.  Now the right
     function pointer is checked before calling"

* tag 'iommu-fixes-v3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/core: Check for the right function pointer in iommu_map()
  iommu/amd: Fix cleanup_domain for mass device removal
  iommu/vt-d: Defer domain removal if device is assigned to a driver

Description of problem:
The NIC card is not reporting back to the driver the transmitted skbs,
so they get stuck in the TX ring causing issues with reference
counters in other kernel components.

Developed a new Automatic Egress Queue Update firmware facility to slowly tick
through Egress Queues and send back any outstanding CIDX Updates which are
laying around.

Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Marc Kleine-Budde says:

====================
pull-request: can 2014-08-21

The first patch is from Mirza Krak, it fixes the initialization of the hardware
in the sja1000 driver. The next patch is contributed by Dan Carpenter, it fixes
the error handling in the c_can's probe function. Then there are two patches
for the flexcan driver, one by Alexander Stein, which fixes the resetting of
the bus error interrupt mask, the other one by Sebastian Andrzej Siewior which
adds an additional error state transition message.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a possible race condition when we unregister the PCI Driver and then
flush/destroy the global "workq". This could lead to situations where there
are tasks on the Work Queue with references to now deleted adapter data
structures. Instead, have per-adapter Work Queues which were instantiated and
torn down in init_one() and remove_one(), respectively.

v2: Remove unnecessary call to flush_workqueue() before destroy_workqueue()
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the transport has always been in state SCTP_UNCONFIRMED, it
therefore wasn't active before and hasn't been used before, and it
always has been, so it is unnecessary to bug the user with a
notification.
Reported-by: Deepak Khandelwal <khandelwal.deepak.1987@gmail.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Suggested-by: Michael Tuexen <tuexen@fh-muenster.de>
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Zhu Yanjun <Yanjun.Zhu@windriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 91ebb929 ("bnx2x: Add support for Multi-Function UNDI") [which was
later supposedly fixed by de682941 ("bnx2x: Fix UNDI driver unload")]
introduced a bug in which in some [yet-to-be-determined] scenarios the
alternative flushing mechanism which was to guarantee the Rx buffers are
empty before resetting them during device probe will fail.
If this happens, when device will be loaded once more a fatal attention will
occur; Since this most likely happens in boot from SAN scenarios, the machine
will fail to load.

Notice this may occur not only in the 'Multi-Function' scenario but in the
regular scenario as well, i.e., this introduced a regression in the driver's
ability to perform boot from SAN.

The patch reverts the mechanism and applies the old scheme to multi-function
devices as well as to single-function devices.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shahed Shaikh says:

====================
qlcnic: Bug fixes

This series fixes some bugs related to endianess.

Please apply this series to net.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware binary file is in little endian. On big-endian architecture, while
writing this binary FW file to adapters memory, writel() swaps the data resulting into
corruption of FW image. So, swap the data before writing into adapters memory.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Firmware dump template header is read from adapter using
readl() which swaps the data. So, adjust structure
element on the boundary of 32bit dword.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Application expects flash data in little endian, but driver reads/writes
flash data using readl()/writel() APIs which swaps data on big endian machine.
So, swap the data after reading from and before writing to flash memory.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alan is the original author of the driver. This change was discussed
with the 802.15.4 subsystem maintainer, Alexander Aring.
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, macvlan code restricts multicast and unicast
filter setting only to passthru devices.  As a result,
if a guest using macvtap wants to receive multicast
traffic, it has to set IFF_ALLMULTI or IFF_PROMISC.

This patch makes it possible to use the fdb interface
to add multicast addresses to the filter thus allowing
a guest to receive only targeted multicast traffic.

CC: John Fastabend <john.r.fastabend@intel.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

af_packet can currently overwrite kernel memory by out of bound
accesses, because it assumed a [new] block can always hold one frame.

This is not generally the case, even if most existing tools do it right.

This patch clamps too long frames as API permits, and issue a one time
error on syslog.

[  394.357639] tpacket_rcv: packet too big, clamped from 5042 to 3966. macoff=82

In this example, packet header tp_snaplen was set to 3966,
and tp_len was set to 5042 (skb->len)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: f6fb8f10 ("af-packet: TPACKET_V3 flexible buffer implementation.")
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Added entry for ec_bhf driver.
Signed-off-by: Dariusz Marcinkiewicz <reksio@newterm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>

The LECS response contains the MTU that should be used.  Correctly
synchronize with other layers when updating.
Signed-off-by: Chas Williams - CONTRACTOR <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull libata fixes from Tejun Heo:
 "Nothing drastic but pushing out early due to build breakage in the new
  tegra platform.

  Additionally:

   - M550 tagged trim blacklist pattern is widened so that it matches
     the new 1TB model

   - three controller specific fixes"

* 'for-3.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata: widen Crucial M550 blacklist matching
  pata_scc: propagate return value of scc_wait_after_reset
  ata: ahci_tegra: Change include to fix compilation
  pata_samsung_cf: change ret type to signed
  ahci_xgene: Removing NCQ support from the APM X-Gene SoC AHCI SATA Host Controller driver.

Pull HID fixes from Jiri Kosina:

 - fixes for a couple potential memory corruption problems (the HW would
   have to be manufactured to be deliberately evil to trigger those)
   found by Ben Hawkes
 - fix for potential infinite loop when using sysfs interface of
   logitech driver, from Simon Wood
 - a couple more simple driver fixes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: fix a couple of off-by-ones
  HID: logitech: perform bounds checking on device_id early enough
  HID: logitech: fix bounds checking on LED report size
  HID: logitech: Prevent possibility of infinite loop when using /sys interface
  HID: rmi: print an error if F11 is not found instead of stopping the device
  HID: hid-sensor-hub: use devm_ functions consistently
  HID: huion: Use allocated buffer for DMA
  HID: huion: Fail on parameter retrieval errors

Pull sound fixes from Takashi Iwai:
 "A bunch of ASoC fixes with a few HD-audio fixes in this pull request.

  All fairly small, boring and device-specific fixes, in addition to
  MAINTAINERS update for better reviewing"

* tag 'sound-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda/hdmi - apply Valleyview fix-ups to Cherryview display codec
  ALSA: hda/hdmi - set depop_delay for haswell plus
  ALSA: hda - restore the gpio led after resume
  ALSA: hda/realtek - Avoid setting wrong COEF on ALC269 & co
  ASoC: pxa-ssp: drop SNDRV_PCM_FMTBIT_S24_LE
  ASoC: fsl-esai: Revert .xlate_tdm_slot_mask() support
  ASoC: mcasp: Fix implicit BLCK divider setting
  ASoC: arizona: Fix TDM slot length handling in arizona_hw_params
  ASoC: pcm512x: Correct Digital Playback control names
  ASoC: dapm: Fix uninitialized variable in snd_soc_dapm_get_enum_double()
  ASoC: Intel: Restore Baytrail ADSP streams only when ADSP was in reset
  ASoC: Intel: Wait Baytrail ADSP boot at resume_early stage
  ASoC: Intel: Merge Baytrail ADSP suspend_noirq into suspend_late
  MAINTAINERS: Add i.MX maintainers and paths to Freescale ASoC entry
  ASoC: Intel: Update Baytrail ADSP firmware name

Pull i2c fixes from Wolfram Sang:
 "Here is the fixup for the 'lowlight' of my last pull request.  I2C is
  not selected anymore by I2C_ACPI.  Instead, the code in question now
  depends on I2C=y.

  Also, Mika has agreed to support me and be the maintainer for I2C-ACPI
  related patches.  Finally, a new-ID-patch came along last week"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  MAINTAINERS: add maintainer for ACPI parts of I2C
  i2c: i801: Add PCI ID for Intel Braswell
  i2c: rework kernel config I2C_ACPI

Pull ia64 update from Tony Luck:
 "Add memfd_create syscall to ia64"

* tag 'please-pull-memfd_create' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
  [IA64] Wire up memfd_create() system call

Pull microblaze update from Michal Simek:
 "Wire-up seccomp/getrandom/memfd_create syscalls"

* tag 'microblaze-3.17-rc2' of git://git.monstr.eu/linux-2.6-microblaze:
  microblaze: Wire-up memfd_create syscall
  microblaze: Wire-up getrandom syscall
  microblaze: Wire-up seccomp syscall

There are a few very theoretical off-by-one bugs in report descriptor size
checking when performing a pre-parsing fixup. Fix those.

Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

device_index is a char type and the size of paired_dj_deivces is 7
elements, therefore proper bounds checking has to be applied to
device_index before it is used.

We are currently performing the bounds checking in
logi_dj_recv_add_djhid_device(), which is too late, as malicious device
could send REPORT_TYPE_NOTIF_DEVICE_UNPAIRED early enough and trigger the
problem in one of the report forwarding functions called from
logi_dj_raw_event().

Fix this by performing the check at the earliest possible ocasion in
logi_dj_raw_event().

Cc: stable@vger.kernel.org
Reported-by: Ben Hawkes <hawkes@google.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>