Following changes have been made:

1. Outstanding commands are based on a request queue, scsi_qla_host
   does not maintain it anymore.

2. start_scsi is accessed via isp_ops struct instead of direct
   invocation.

3. Interrupt registrations are done using response queue instead of
   device id.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Following changes have been made to the qla2xxx FC driver in
preparation for the multi- queue and future SR IOV hardware.

1. scsi_qla_host structure has been changed to contain scsi host
   specific data only.

2. A new structure, qla_hw_data is created to contain HBA specific
   hardware data.

3. Request and response IO specific data strucures are created.

4. The global list of fcports for the hba is not maintained anymore,
   instead a fcport list is construted on per scsi_qla_host.
Signed-of-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

This patch improves handling of TASK ABORTED status by Linux SCSI
mid-layer. Currently, command returned with this status considered
failed and returned to upper layers. It leads to additional error
recovery load on file systems and block layer, which sometimes can
cause undesired side effects, like I/O errors and file systems
corruptions. See http://lkml.org/lkml/2008/11/1/38, for instance.

From other side, TASK ABORTED status is returned by SCSI target if the
corresponding command was aborted by another initiator and the target
has TAS bit set in the control mode page. So, in the majority of cases
commands with TASK ABORTED status should be simply retried. In other
cases, maybe_retry path will not retry if no retries are allowed.

This patch implement suggestion by James Bottomley from
http://marc.info/?l=linux-scsi&m=121932916906009&w=2.
Signed-off-by: Vladislav Bolkhovitin <vst@vlnb.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

When the mode select sent to the controller fails with the retryable
error, it is better to retry the mode_select from the hardware handler
itself, instead of propagating the failure to dm-multipath.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

[SCSI] scsi_dh: Make sure the state of a path is set properly when controller is swapped from passive to active

When the controller ownership is changed (from passive to active),
check_ownership() doesn't set the state of the device to ACTIVE.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Reported-by: "Moger, Babu" <Babu.Moger@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

...and the list of recent breakage goes on and on, this time
it's 242f9dcb (block: unify request timeout handling)
which broke it.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Lucky winner is 557cc476 ([SCSI] tmscsim: Fixup
KERN_INFO in printk).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

When unsigned, scsi_dma_map may return -ENOMEM without triggering BUG_ON()
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Use the macro DIV_ROUND_UP and eliminate the variable rounded_up, as
suggested by Matthew Wilcox.
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: David Miller <davem@davemloft.net>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Bump driver version.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Stops gcc from complaining about a possible uninitialized
variable being used in ibmvfc_reset_device.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

If the ibmvfc driver is in discovery attempting to log into a target
and it encounters an error, the command may get retried one or more
times, depending on the error received. If the retries are
unsuccessful such that the discovery thread gives up on discovery to
that target, the target ends up in a state where, if SCSI core had
previously known about the device, the host will get unblocked but the
host will not be logged into the target, causing any commands sent to
the target to fail. This patch fixes this so that if this occurs, the
target is deleted such that the normal dev_loss processing can occur
instead.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Due to an ambiguity in the VIOS VFC interface specification,
abort/cancel handling is not done correctly and can result in double
completion of commands. In order to cancel all outstanding commands to
a device, a cancel must be sent, followed by an abort task set. After
the responses are received for these commands, there may still be
commands outstanding, in the process of getting flushed back, in which
case, we need to wait for them. This patch removes the assumption that
if the abort and the cancel both complete successfully that the device
queue has been flushed and waits for all the responses to come back.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

If either a "transport fault" or a "general transport" error is received
and no other error information is available, the command is improperly
returned as successful. Fix this to return DID_ERROR in this case.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

The ibmvfc log level filtering logic was reversed. The log_level scsi
host parameter should result in more verbose logs when log_level is
larger, not smaller.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

We need to check the address that pci_alloc_consistent() returns since
it might fail.

When pci_alloc_consistent() fails, some IOMMUs set the dma_handle
argument to zero. So we can't use fibptr->hw_fib_pa directly here.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Aacraid List <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Use the newly introduced pci_ioremap_bar() function in drivers/scsi.
pci_ioremap_bar() just takes a pci device and a bar number, with the goal
of making it really hard to get wrong, while also having a central place
to stick sanity checks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Brian King <brking@us.ibm.com>
Cc: Ed Lin <ed.lin@promise.com>
Cc: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

Fix kernel-doc parameter warning and correct the function name:

Warning(linux-next-20081022//drivers/scsi/scsi_ioctl.c:281): No description found for parameter 'ndelay'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (144 commits)
  powerpc/44x: Support 16K/64K base page sizes on 44x
  powerpc: Force memory size to be a multiple of PAGE_SIZE
  powerpc/32: Wire up the trampoline code for kdump
  powerpc/32: Add the ability for a classic ppc kernel to be loaded at 32M
  powerpc/32: Allow __ioremap on RAM addresses for kdump kernel
  powerpc/32: Setup OF properties for kdump
  powerpc/32/kdump: Implement crash_setup_regs() using ppc_save_regs()
  powerpc: Prepare xmon_save_regs for use with kdump
  powerpc: Remove default kexec/crash_kernel ops assignments
  powerpc: Make default kexec/crash_kernel ops implicit
  powerpc: Setup OF properties for ppc32 kexec
  powerpc/pseries: Fix cpu hotplug
  powerpc: Fix KVM build on ppc440
  powerpc/cell: add QPACE as a separate Cell platform
  powerpc/cell: fix build breakage with CONFIG_SPUFS disabled
  powerpc/mpc5200: fix error paths in PSC UART probe function
  powerpc/mpc5200: add rts/cts handling in PSC UART driver
  powerpc/mpc5200: Make PSC UART driver update serial errors counters
  powerpc/mpc5200: Remove obsolete code from mpc5200 MDIO driver
  powerpc/mpc5200: Add MDMA/UDMA support to MPC5200 ATA driver
  ...

Fix trivial conflict in drivers/char/Makefile as per Paul's directions

Commit 908a7a16 ("net: Remove unused
netdev arg from some NAPI interfaces") missed two spots.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  smackfs: check for allocation failures in smk_set_access()

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (25 commits)
  allow stripping of generated symbols under CONFIG_KALLSYMS_ALL
  kbuild: strip generated symbols from *.ko
  kbuild: simplify use of genksyms
  kernel-doc: check for extra kernel-doc notations
  kbuild: add headerdep used to detect inclusion cycles in header files
  kbuild: fix string equality testing in tags.sh
  kbuild: fix make tags/cscope
  kbuild: fix make incompatibility
  kbuild: remove TAR_IGNORE
  setlocalversion: add git-svn support
  setlocalversion: print correct subversion revision
  scripts: improve the decodecode script
  scripts/package: allow custom options to rpm
  genksyms: allow to ignore symbol checksum changes
  genksyms: track symbol checksum changes
  tags and cscope support really belongs in a shell script
  kconfig: fix options to check-lxdialog.sh
  kbuild: gen_init_cpio expands shell variables in file names
  remove bashisms from scripts/extract-ikconfig
  kbuild: teach mkmakfile to be silent
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-nvram:
  [PATCH] nvram - convert PRINT_PROC to seq_file
  [PATCH] nvram - CodingStyle

This adds support for 16k and 64k page sizes on PowerPC 44x processors.

The PGDIR table is much smaller than a page when using 16k or 64k
pages (512 and 32 bytes respectively) so we allocate the PGDIR with
kzalloc() instead of __get_free_pages().

One PTE table covers rather a large memory area when using 16k or 64k
pages (32MB or 512MB respectively), so we can easily put FIXMAP and
PKMAP in the area covered by one PTE table.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Vladimir Panfilov <pvr@emcraft.com>
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

Ensure that total memory size is page-aligned, because otherwise
mark_bootmem() gets upset.

This error case was triggered by using 64 KiB pages in the kernel
while arch/powerpc/boot/4xx.c arbitrarily reduced the amount of memory
by 4096 (to work around a chip bug that affects the last 256 bytes of
physical memory).
Signed-off-by: Hollis Blanchard <hollisb@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
  m68k: use the new byteorder headers
  fbcon: Protect free_irq() by MACH_IS_ATARI check
  fbcon: remove broken mac vbl handler
  m68k: fix trigraph ignored warning in setox.S
  macfb annotations and compiler warning fix
  m68k: mac baboon interrupt enable/disable
  m68k: machw.h cleanup
  m68k: Mac via cleanup and commentry
  m68k: Reinstate mac rtc

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1429 commits)
  net: Allow dependancies of FDDI & Tokenring to be modular.
  igb: Fix build warning when DCA is disabled.
  net: Fix warning fallout from recent NAPI interface changes.
  gro: Fix potential use after free
  sfc: If AN is enabled, always read speed/duplex from the AN advertising bits
  sfc: When disabling the NIC, close the device rather than unregistering it
  sfc: SFT9001: Add cable diagnostics
  sfc: Add support for multiple PHY self-tests
  sfc: Merge top-level functions for self-tests
  sfc: Clean up PHY mode management in loopback self-test
  sfc: Fix unreliable link detection in some loopback modes
  sfc: Generate unique names for per-NIC workqueues
  802.3ad: use standard ethhdr instead of ad_header
  802.3ad: generalize out mac address initializer
  802.3ad: initialize ports LACPDU from const initializer
  802.3ad: remove typedef around ad_system
  802.3ad: turn ports is_individual into a bool
  802.3ad: turn ports is_enabled into a bool
  802.3ad: make ntt bool
  ixgbe: Fix set_ringparam in ixgbe to use the same memory pools.
  ...

Fixed trivial IPv4/6 address printing conflicts in fs/cifs/connect.c due
to the conversion to %pI (in this networking merge) and the addition of
doing IPv6 addresses (from the earlier merge of CIFS).

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: (31 commits)
  [CIFS] Remove redundant test
  [CIFS] make sure that DFS pathnames are properly formed
  Remove an already-checked error condition in SendReceiveBlockingLock
  Streamline SendReceiveBlockingLock: Use "goto out:" in an error condition
  Streamline SendReceiveBlockingLock: Use "goto out:" in an error condition
  [CIFS] Streamline SendReceive[2] by using "goto out:" in an error condition
  Slightly streamline SendReceive[2]
  Check the return value of cifs_sign_smb[2]
  [CIFS] Cleanup: Move the check for too large R/W requests
  [CIFS] Slightly simplify wait_for_free_request(), remove an unnecessary "else" branch
  Simplify allocate_mid() slightly: Remove some unnecessary "else" branches
  [CIFS] In SendReceive, move consistency check out of the mutexed region
  cifs: store password in tcon
  cifs: have calc_lanman_hash take more granular args
  cifs: zero out session password before freeing it
  cifs: fix wait_for_response to time out sleeping processes correctly
  [CIFS] Can not mount with prefixpath if root directory of share is inaccessible
  [CIFS] various minor cleanups pointed out by checkpatch script
  [CIFS] fix typo
  [CIFS] remove sparse warning
  ...

Fix trivial conflict in fs/cifs/cifs_fs_sb.h due to comment changes for
the CIFS_MOUNT_xyz bit definitions between cifs updates and security
updates.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (26 commits)
  IB/mlx4: Set ownership bit correctly when copying CQEs during CQ resize
  RDMA/nes: Remove tx_free_list
  RDMA/cma: Add IPv6 support
  RDMA/addr: Add support for translating IPv6 addresses
  mlx4_core: Delete incorrect comment
  mlx4_core: Add support for multiple completion event vectors
  IB/iser: Avoid recv buffer exhaustion caused by unexpected PDUs
  IB/ehca: Remove redundant test of vpage
  IB/ehca: Replace modulus operations in flush error completion path
  IB/ipath: Add locking for interrupt use of ipath_pd contexts vs free
  IB/ipath: Fix spi_pioindex value
  IB/ipath: Only do 1X workaround on rev1 chips
  IB/ipath: Don't count IB symbol and link errors unless link is UP
  IB/ipath: Check return value of dma_map_single()
  IB/ipath: Fix PSN of send WQEs after an RDMA read resend
  RDMA/nes: Cleanup warnings
  RDMA/nes: Add loopback check to make_cm_node()
  RDMA/nes: Check cqp_avail_reqs is empty after locking the list
  RDMA/nes: Fix TCP compliance test failures
  RDMA/nes: Forward packets for a new connection with stale APBVT entry
  ...

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6: (85 commits)
  [S390] provide documentation for hvc_iucv kernel parameter.
  [S390] convert ctcm printks to dev_xxx and pr_xxx macros.
  [S390] convert zfcp printks to pr_xxx macros.
  [S390] convert vmlogrdr printks to pr_xxx macros.
  [S390] convert zfcp dumper printks to pr_xxx macros.
  [S390] convert cpu related printks to pr_xxx macros.
  [S390] convert qeth printks to dev_xxx and pr_xxx macros.
  [S390] convert sclp printks to pr_xxx macros.
  [S390] convert iucv printks to dev_xxx and pr_xxx macros.
  [S390] convert ap_bus printks to pr_xxx macros.
  [S390] convert dcssblk and extmem printks messages to pr_xxx macros.
  [S390] convert monwriter printks to pr_xxx macros.
  [S390] convert s390 debug feature printks to pr_xxx macros.
  [S390] convert monreader printks to pr_xxx macros.
  [S390] convert appldata printks to pr_xxx macros.
  [S390] convert setup printks to pr_xxx macros.
  [S390] convert hypfs printks to pr_xxx macros.
  [S390] convert time printks to pr_xxx macros.
  [S390] convert cpacf printks to pr_xxx macros.
  [S390] convert cio printks to pr_xxx macros.
  ...

Merge branch 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
  sched: fix warning in fs/proc/base.c
  schedstat: consolidate per-task cpu runtime stats
  sched: use RCU variant of list traversal in for_each_leaf_rt_rq()
  sched, cpuacct: export percpu cpuacct cgroup stats
  sched, cpuacct: refactoring cpuusage_read / cpuusage_write
  sched: optimize update_curr()
  sched: fix wakeup preemption clock
  sched: add missing arch_update_cpu_topology() call
  sched: let arch_update_cpu_topology indicate if topology changed
  sched: idle_balance() does not call load_balance_newidle()
  sched: fix sd_parent_degenerate on non-numa smp machine
  sched: add uid information to sched_debug for CONFIG_USER_SCHED
  sched: move double_unlock_balance() higher
  sched: update comment for move_task_off_dead_cpu
  sched: fix inconsistency when redistribute per-cpu tg->cfs_rq shares
  sched/rt: removed unneeded defintion
  sched: add hierarchical accounting to cpu accounting controller
  sched: include group statistics in /proc/sched_debug
  sched: rename SCHED_NO_NO_OMIT_FRAME_POINTER => SCHED_OMIT_FRAME_POINTER
  sched: clean up SCHED_CPUMASK_ALLOC
  ...

Merge branch 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (241 commits)
  sched, trace: update trace_sched_wakeup()
  tracing/ftrace: don't trace on early stage of a secondary cpu boot, v3
  Revert "x86: disable X86_PTRACE_BTS"
  ring-buffer: prevent false positive warning
  ring-buffer: fix dangling commit race
  ftrace: enable format arguments checking
  x86, bts: memory accounting
  x86, bts: add fork and exit handling
  ftrace: introduce tracing_reset_online_cpus() helper
  tracing: fix warnings in kernel/trace/trace_sched_switch.c
  tracing: fix warning in kernel/trace/trace.c
  tracing/ring-buffer: remove unused ring_buffer size
  trace: fix task state printout
  ftrace: add not to regex on filtering functions
  trace: better use of stack_trace_enabled for boot up code
  trace: add a way to enable or disable the stack tracer
  x86: entry_64 - introduce FTRACE_ frame macro v2
  tracing/ftrace: add the printk-msg-only option
  tracing/ftrace: use preempt_enable_no_resched_notrace in ring_buffer_time_stamp()
  x86, bts: correctly report invalid bts records
  ...

Fixed up trivial conflict in scripts/recordmcount.pl due to SH bits
being already partly merged by the SH merge.

Merge branch 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (246 commits)
  x86: traps.c replace #if CONFIG_X86_32 with #ifdef CONFIG_X86_32
  x86: PAT: fix address types in track_pfn_vma_new()
  x86: prioritize the FPU traps for the error code
  x86: PAT: pfnmap documentation update changes
  x86: PAT: move track untrack pfnmap stubs to asm-generic
  x86: PAT: remove follow_pfnmap_pte in favor of follow_phys
  x86: PAT: modify follow_phys to return phys_addr prot and return value
  x86: PAT: clarify is_linear_pfn_mapping() interface
  x86: ia32_signal: remove unnecessary declaration
  x86: common.c boot_cpu_stack and boot_exception_stacks should be static
  x86: fix intel x86_64 llc_shared_map/cpu_llc_id anomolies
  x86: fix warning in arch/x86/kernel/microcode_amd.c
  x86: ia32.h: remove unused struct sigfram32 and rt_sigframe32
  x86: asm-offset_64: use rt_sigframe_ia32
  x86: sigframe.h: include headers for dependency
  x86: traps.c declare functions before they get used
  x86: PAT: update documentation to cover pgprot and remap_pfn related changes - v3
  x86: PAT: add pgprot_writecombine() interface for drivers - v3
  x86: PAT: change pgprot_noncached to uc_minus instead of strong uc - v3
  x86: PAT: implement track/untrack of pfnmap regions for x86 - v3
  ...

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (105 commits)
  SELinux: don't check permissions for kernel mounts
  security: pass mount flags to security_sb_kern_mount()
  SELinux: correctly detect proc filesystems of the form "proc/foo"
  Audit: Log TIOCSTI
  user namespaces: document CFS behavior
  user namespaces: require cap_set{ug}id for CLONE_NEWUSER
  user namespaces: let user_ns be cloned with fairsched
  CRED: fix sparse warnings
  User namespaces: use the current_user_ns() macro
  User namespaces: set of cleanups (v2)
  nfsctl: add headers for credentials
  coda: fix creds reference
  capabilities: define get_vfs_caps_from_disk when file caps are not enabled
  CRED: Allow kernel services to override LSM settings for task actions
  CRED: Add a kernel_service object class to SELinux
  CRED: Differentiate objective and effective subjective credentials on a task
  CRED: Documentation
  CRED: Use creds in file structs
  CRED: Prettify commoncap.c
  CRED: Make execve() take advantage of copy-on-write credentials
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (57 commits)
  crypto: aes - Precompute tables
  crypto: talitos - Ack done interrupt in isr instead of tasklet
  crypto: testmgr - Correct comment about deflate parameters
  crypto: salsa20 - Remove private wrappers around various operations
  crypto: des3_ede - permit weak keys unless REQ_WEAK_KEY set
  crypto: sha512 - Switch to shash 
  crypto: sha512 - Move message schedule W[80] to static percpu area
  crypto: michael_mic - Switch to shash
  crypto: wp512 - Switch to shash
  crypto: tgr192 - Switch to shash
  crypto: sha256 - Switch to shash
  crypto: md5 - Switch to shash
  crypto: md4 - Switch to shash
  crypto: sha1 - Switch to shash
  crypto: rmd320 - Switch to shash
  crypto: rmd256 - Switch to shash
  crypto: rmd160 - Switch to shash
  crypto: rmd128 - Switch to shash
  crypto: null - Switch to shash
  crypto: hash - Make setkey optional
  ...

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (367 commits)
  ALSA: ASoC: fix a typo in omp-pcm.c
  ASoC: Fix DSP formats in SSM2602 audio codec
  ASoC: Fix incorrect DSP format in OMAP McBSP DAI and affected drivers
  ALSA: hda: fix incorrect mixer index values for 92hd83xx
  ALSA: hda: dinput_mux check
  ALSA: hda - Add quirk for another HP dv7
  ALSA: ASoC - Add missing __devexit annotation to wm8350.c
  ALSA: ASoc: DaVinci: davinci-evm use dsp_b mode
  ALSA: ASoC: DaVinci: i2s, evm, pass same value to codec and cpu_dai
  ALSA: ASoC: tlv320aic3x add dsp_a
  ALSA: ASoC: DaVinci: document I2S limitations
  ALSA: ASoC: DaVinci: davinci-i2s clean up
  ALSA: ASoC: DaVinci: davinci-i2s clean up
  ALSA: ASoC: DaVinci: davinci-i2s add comments to explain polarity
  ALSA: ASoC: DaVinci: davinvi-evm, make requests explicit
  ALSA: ca0106 - disable 44.1kHz capture
  ALSA: ca0106 - Add missing card->private_data initialization
  ALSA: ca0106 - Check ac97 availability at PM
  ALSA: hda - Power up always when no jack detection is available
  ALSA: hda - Fix unused variable warnings in patch_sigmatel.c
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (132 commits)
  sh: oprofile: Fix up the module build.
  sh: add UIO support for JPU on SH7722.
  serial: sh-sci: Fix up port pinmux for SH7366.
  sh: mach-rsk: Use uImage generation by default for rsk7201/7203.
  sh: mach-sh03: Fix up pata_platform build breakage.
  sh: enable deferred io LCDC on Migo-R
  video: sh_mobile_lcdcfb deferred io support
  video: deferred io with physically contiguous memory
  video: deferred io cleanup
  video: fix deferred io fsync()
  sh: add LCDC interrupt configuration to AP325 and Migo-R
  sh_mobile_lcdc: use FB_SYS helpers instead of FB_CFB
  sh: split coherent pages
  sh: dma: Kill off ISA DMA wrapper.
  sh: Conditionalize the code dumper on CONFIG_DUMP_CODE.
  sh: Kill off the unused SH_ALPHANUMERIC debug option.
  sh: Enable skipping of bss on debug platforms for sh32 also.
  doc: Update sh cpufreq documentation.
  sh: mrshpc_setup_windows() needs to be inline.
  serial: sh-sci: sci_poll_get_char() is only used by CONFIG_CONSOLE_POLL.
  ...