With CONFIG_VMAP_STACK=y, virtnet_set_mac_address() can be passed a
pointer to the stack and it will OOPS.  Copy the address to the heap
to prevent the crash.

Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Laura Abbott <labbott@redhat.com>
Reported-by: zbyszek@in.waw.pl
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There have been some reports lately about TCP connection stalls caused
by NIC drivers that aren't setting gso_size on aggregated packets on rx
path. This causes TCP to assume that the MSS is actually the size of the
aggregated packet, which is invalid.

Although the proper fix is to be done at each driver, it's often hard
and cumbersome for one to debug, come to such root cause and report/fix
it.

This patch amends this situation in two ways. First, it adds a warning
on when this situation occurs, so it gives a hint to those trying to
debug this. It also limit the maximum probed MSS to the adverised MSS,
as it should never be any higher than that.

The result is that the connection may not have the best performance ever
but it shouldn't stall, and the admin will have a hint on what to look
for.

Tested with virtio by forcing gso_size to 0.

v2: updated msg per David's suggestion
v3: use skb_iif to find the interface and also log its name, per Eric
    Dumazet's suggestion. As the skb may be backlogged and the interface
    gone by then, we need to check if the number still has a meaning.
v4: use helper tcp_gro_dev_warn() and avoid pr_warn_once inside __once, per
    David's suggestion

Cc: Jonathan Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix a wrong condition preventing the higher net device flags
IFF_LOWER_UP etc to be defined if net/if.h is included before
linux/if.h.

The comment makes it clear the intention was to allow partial
definition with either parts.

This fixes compilation of userspace programs trying to use
IFF_LOWER_UP, IFF_DORMANT or IFF_ECHO.

Fixes: 4a91cb61 ("uapi glibc compat: fix compile errors when glibc net/if.h included before linux/if.h")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>

WR_OSR_LMT and RD_OSR_LMT have a reset value of 1.
Since the reset value wasn't cleared before writing, the value in the
register would be incorrect if specifying an uneven value for
snps,wr_osr_lmt/snps,rd_osr_lmt.

Zero is a valid value for the properties, since the databook specifies:
maximum outstanding requests = WR_OSR_LMT + 1.

We do not want to change the behavior for existing users when the
property is missing. Therefore, default to 1 if the property is missing,
since that is the same as the reset value.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It is wrong to schedule a work from sk_destruct using the socket
as the memory reserve because the socket will be freed immediately
after the return from sk_destruct.

Instead we should do the deferral prior to sk_free.

This patch does just that.

Fixes: 707693c8 ("netlink: Call cb->done from a worker thread")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

File is in uapi directory but not being copied on
 make install_headers

Fixes commit 4ec9c8fbbc22 ("netfilter: nft_log: complete
NFTA_LOG_FLAGS attr support").
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes commit 735cffe5d800 ("net_sched: Introduce skbmod action")
Not used by iproute2 but maybe in future.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When we unload the ep93xx_eth, whether we have opened the network
interface or not, we will either hit a kernel paging request error, or a
simple NULL pointer de-reference because:

- if ep93xx_open has been called, we have created a valid DMA mapping
  for ep->descs, when we call ep93xx_stop, we also call
  ep93xx_free_buffers, ep->descs now has a stale value

- if ep93xx_open has not been called, we have a NULL pointer for
  ep->descs, so performing any operation against that address just won't
  work

Fix this by adding a NULL pointer check for ep->descs which means that
ep93xx_free_buffers() was able to successfully tear down the descriptors
and free the DMA cookie as well.

Fixes: 1d22e05d ("[PATCH] Cirrus Logic ep93xx ethernet driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
bnx2x: fixes series

Two unrelated fixes for bnx2x - the first one is nice-to-have,
while the other fixes fatal behaviour in older adapters.

Please consider applying them to `net'.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Only the 578xx adapters are capable of configuring UDP ports for
the purpose of tunnelling - doing the same on 577xx might lead to
a firmware assertion.
We're already not claiming support for any related feature for such
devices, but we also need to prevent the configuration of the UDP
ports to the device in this case.

Fixes: f34fa14c ("bnx2x: Add vxlan RSS support")
Reported-by: Anikina Anna <anikina@gmail.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Until interface is up [and assuming ringparams weren't explicitly
configured] when queried for the size of its rings bnx2x would
claim they're the maximal size by default.
That is incorrect as by default the maximal number of buffers would
be equally divided between the various rx rings.

This prevents the user from actually setting the number of elements
on each rx ring to be of maximal size prior to transitioning the
interface into up state.

To fix this, make a rough estimation about the number of buffers.
It wouldn't always be accurate, but it would be much better than
current estimation and would allow users to increase number of
buffers during early initialization of the interface.
Reported-by: Seymour, Shane <shane.seymour@hpe.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function hfc4s8s_probe(), the value of return variable err should be
negative on failures. However, when the call to request_region() returns
NULL, the value of err is 0. This patch fixes the bug, assigning
"-EBUSY" to err on the path that request_region() fails.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188931Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Macro BNX2X_ALLOC_AND_SET(arr, lbl, func) calls kmalloc() to allocate
memory, and jumps to label "lbl" if the allocation fails. Label "lbl"
first cleans memory and then returns variable rc. Before calling the
macro, the value of variable rc is 0. Because 0 means no error, the
callers of bnx2x_init_firmware() may be misled. This patch fixes the bug,
assigning "-ENOMEM" to rc before calling macro NX2X_ALLOC_AND_SET().

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189141Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When calling dma_mapping_error(), the value of return variable rc is 0.
And when the call returns an unexpected value, rc is not set to a
negative errno. Thus, it will return 0 on the error path, and its
callers cannot detect the bug. This patch fixes the bug, assigning
"-ENOMEM" to err.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189041Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It returns variable "error" when ioremap_nocache() returns a NULL
pointer. The value of "error" is 0 then, which will mislead the callers
to believe that there is no error. This patch fixes the bug, returning
"-ENOMEM".

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189021Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the calls to kzalloc() fail, the value of return variable ret may
be 0. 0 means success in this context. This patch fixes the bug,
assigning "-ENOMEM" to ret before calling kzalloc().

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188971Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The check of the return value of sock_register() is ineffective.
"if(!err)" seems to be a typo. It is better to propagate the error code
to the callers of caif_sktinit_module(). This patch removes the check
statment and directly returns the result of sock_register().

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188751Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prior to commit c0371da6 ("put iov_iter into msghdr") in v3.19, there
was no check that the iovec contained enough bytes for an ICMP header,
and the read loop would walk across neighboring stack contents. Since the
iov_iter conversion, bad arguments are noticed, but the returned error is
EFAULT. Returning EINVAL is a clearer error and also solves the problem
prior to v3.19.

This was found using trinity with KASAN on v3.18:

BUG: KASAN: stack-out-of-bounds in memcpy_fromiovec+0x60/0x114 at addr ffffffc071077da0
Read of size 8 by task trinity-c2/9623
page:ffffffbe034b9a08 count:0 mapcount:0 mapping:          (null) index:0x0
flags: 0x0()
page dumped because: kasan: bad access detected
CPU: 0 PID: 9623 Comm: trinity-c2 Tainted: G    BU         3.18.0-dirty #15
Hardware name: Google Tegra210 Smaug Rev 1,3+ (DT)
Call trace:
[<ffffffc000209c98>] dump_backtrace+0x0/0x1ac arch/arm64/kernel/traps.c:90
[<ffffffc000209e54>] show_stack+0x10/0x1c arch/arm64/kernel/traps.c:171
[<     inline     >] __dump_stack lib/dump_stack.c:15
[<ffffffc000f18dc4>] dump_stack+0x7c/0xd0 lib/dump_stack.c:50
[<     inline     >] print_address_description mm/kasan/report.c:147
[<     inline     >] kasan_report_error mm/kasan/report.c:236
[<ffffffc000373dcc>] kasan_report+0x380/0x4b8 mm/kasan/report.c:259
[<     inline     >] check_memory_region mm/kasan/kasan.c:264
[<ffffffc00037352c>] __asan_load8+0x20/0x70 mm/kasan/kasan.c:507
[<ffffffc0005b9624>] memcpy_fromiovec+0x5c/0x114 lib/iovec.c:15
[<     inline     >] memcpy_from_msg include/linux/skbuff.h:2667
[<ffffffc000ddeba0>] ping_common_sendmsg+0x50/0x108 net/ipv4/ping.c:674
[<ffffffc000dded30>] ping_v4_sendmsg+0xd8/0x698 net/ipv4/ping.c:714
[<ffffffc000dc91dc>] inet_sendmsg+0xe0/0x12c net/ipv4/af_inet.c:749
[<     inline     >] __sock_sendmsg_nosec net/socket.c:624
[<     inline     >] __sock_sendmsg net/socket.c:632
[<ffffffc000cab61c>] sock_sendmsg+0x124/0x164 net/socket.c:643
[<     inline     >] SYSC_sendto net/socket.c:1797
[<ffffffc000cad270>] SyS_sendto+0x178/0x1d8 net/socket.c:1761

CVE-2016-8399
Reported-by: Qidan He <i@flanker017.me>
Fixes: c319b4d7 ("net: ipv4: add IPPROTO_ICMP socket kind")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function lanai_dev_open(), when the call to ioremap() fails, the
value of return variable result is 0. 0 means no error in this context.
This patch fixes the bug, assigning "-ENOMEM" to result when ioremap()
returns a NULL pointer.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188791Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function lan78xx_probe(), variable ret takes the errno code on
failures. However, when the call to usb_alloc_urb() fails, its value
will keeps 0. 0 indicates success in the context, which is inconsistent
with the execution result. This patch fixes the bug, assigning
"-ENOMEM" to ret when usb_alloc_urb() returns a NULL pointer.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188771Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function br_sysfs_addbr() does not set error code when the call
kobject_create_and_add() returns a NULL pointer. It may be better to
return "-ENOMEM" when kobject_create_and_add() fails.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188781Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Adding space after switch keyword before open
parenthesis for readability purpose.

This patch fixes the checkpatch.pl warning:
space required before the open parenthesis '('
Signed-off-by: Suraj Deshmukh <surajssd009005@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Function bnxt_hwrm_stat_ctx_alloc() always returns 0, even if the call
to _hwrm_send_message() fails. It may be better to propagate the errors
to the caller of bnxt_hwrm_stat_ctx_alloc().

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188661Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
IPv4 FIB suffix length fixes

In reviewing the patch from Robert Shearman and looking over the code I
realized there were a few different bugs we were still carrying in the IPv4
FIB lookup code.

These two patches are based off of Robert's original patch, but take things
one step further by splitting them up to address two additional issues I
found.

So first have Robert's original patch which was addressing the fact that
us calling update_suffix in resize is expensive when it is called per add.
To address that I incorporated the core bit of the patch which was us
dropping the update_suffix call from resize.

The first patch in the series does a rename and fix on the push_suffix and
pull_suffix code.  Specifically we drop the need to pass a leaf and
secondly we fix things so we pull the suffix as long as the value of the
suffix in the node is dropping.

The second patch addresses the original issue reported as well as
optimizing the code for the fact that update_suffix is only really meant to
go through and clean things up when we are decreasing a suffix.  I had
originally added code for it to somehow cause an increase, but if we push
the suffix when a new leaf is added we only ever have to handle pulling
down the suffix with update_suffix so I updated the code to reflect that.

As far as side effects the only ones I think that will be obvious should be
the fact that some routes may be able to be found earlier since before we
relied on resize to update the suffix lengths, and now we are updating them
before we add or remove the leaf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

It has been reported that update_suffix can be expensive when it is called
on a large node in which most of the suffix lengths are the same.  The time
required to add 200K entries had increased from around 3 seconds to almost
49 seconds.

In order to address this we need to move the code for updating the suffix
out of resize and instead just have it handled in the cases where we are
pushing a node that increases the suffix length, or will decrease the
suffix length.

Fixes: 5405afd1 ("fib_trie: Add tracking value for suffix length")
Reported-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Robert Shearman <rshearma@brocade.com>
Tested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It wasn't necessary to pass a leaf in when doing the suffix updates so just
drop it.  Instead just pass the suffix and work with that.

Since we dropped the leaf there is no need to include that in the name so
the names are updated to node_push_suffix and node_pull_suffix.

Finally I noticed that the logic for pulling the suffix length back
actually had some issues.  Specifically it would stop prematurely if there
was a longer suffix, but it was not as long as the original suffix.  I
updated the code to address that in node_pull_suffix.

Fixes: 5405afd1 ("fib_trie: Add tracking value for suffix length")
Suggested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: Robert Shearman <rshearma@brocade.com>
Tested-by: Robert Shearman <rshearma@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function dcbnl_cee_fill(), returns the value of variable err on
errors. However, on some error paths (e.g. nla put fails), its value may
be 0. It may be better to explicitly set a negative errno to variable
err before returning.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188881Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
Here is another batman-adv bugfix:

 - fix checking for failed allocation of TVLV blocks in TT local data,
   by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull ARM SoC fixes from Arnd Bergmann:
 "This should be the last set of bugfixes for arm-soc in v4.9. None of
  these are critical regressions, but it would be nice to still get them
  merged.

   - On the Juno platform, the idle latency was described wrong, leading
     to suboptimal cpuidle tuning.

   - Also on the same platform, PCI I/O space was set up incorrectly and
     could not work.

   - On the sti platform, a syntactically incorrect DT entry caused
     warnings.

   - The newly added 'gr8' platform has somewhat confusing file names,
     which we rename for consistency"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  arm64: dts: juno: fix cluster sleep state entry latency on all SoC versions
  arm64: dts: juno: Correct PCI IO window
  ARM: dts: STiH407-family: fix i2c nodes
  ARM: gr8: Rename the DTSI and relevant DTS

Pull networking fixes from David Miller:

 1) Lots more phydev and probe error path leaks in various drivers by
    Johan Hovold.

 2) Fix race in packet_set_ring(), from Philip Pettersson.

 3) Use after free in dccp_invalid_packet(), from Eric Dumazet.

 4) Signnedness overflow in SO_{SND,RCV}BUFFORCE, also from Eric
    Dumazet.

 5) When tunneling between ipv4 and ipv6 we can be left with the wrong
    skb->protocol value as we enter the IPSEC engine and this causes all
    kinds of problems. Set it before the output path does any
    dst_output() calls, from Eli Cooper.

 6) bcmgenet uses wrong device struct pointer in DMA API calls, fix from
    Florian Fainelli.

 7) Various netfilter nat bug fixes from FLorian Westphal.

 8) Fix memory leak in ipvlan_link_new(), from Gao Feng.

 9) Locking fixes, particularly wrt. socket lookups, in l2tp from
    Guillaume Nault.

10) Avoid invoking rhash teardowns in atomic context by moving netlink
    cb->done() dump completion from a worker thread. Fix from Herbert
    Xu.

11) Buffer refcount problems in tun and macvtap on errors, from Jason
    Wang.

12) We don't set Kconfig symbol DEFAULT_TCP_CONG properly when the user
    selects BBR. Fix from Julian Wollrath.

13) Fix deadlock in transmit path on altera TSE driver, from Lino
    Sanfilippo.

14) Fix unbalanced reference counting in dsa_switch_tree, from Nikita
    Yushchenko.

15) tc_tunnel_key needs to be properly exported to userspace via uapi,
    fix from Roi Dayan.

16) rds_tcp_init_net() doesn't unregister notifier in error path, fix
    from Sowmini Varadhan.

17) Stale packet header pointer access after pskb_expand_head() in
    genenve driver, fix from Sabrina Dubroca.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
  net: avoid signed overflows for SO_{SND|RCV}BUFFORCE
  geneve: avoid use-after-free of skb->data
  tipc: check minimum bearer MTU
  net: renesas: ravb: unintialized return value
  sh_eth: remove unchecked interrupts for RZ/A1
  net: bcmgenet: Utilize correct struct device for all DMA operations
  NET: usb: qmi_wwan: add support for Telit LE922A PID 0x1040
  cdc_ether: Fix handling connection notification
  ip6_offload: check segs for NULL in ipv6_gso_segment.
  RDS: TCP: unregister_netdevice_notifier() in error path of rds_tcp_init_net
  Revert: "ip6_tunnel: Update skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit()"
  ipv6: Set skb->protocol properly for local output
  ipv4: Set skb->protocol properly for local output
  packet: fix race condition in packet_set_ring
  net: ethernet: altera: TSE: do not use tx queue lock in tx completion handler
  net: ethernet: altera: TSE: Remove unneeded dma sync for tx buffers
  net: ethernet: stmmac: fix of-node and fixed-link-phydev leaks
  net: ethernet: stmmac: platform: fix outdated function header
  net: ethernet: stmmac: dwmac-meson8b: fix probe error path
  net: ethernet: stmmac: dwmac-generic: fix probe error path
  ...

CAP_NET_ADMIN users should not be allowed to set negative
sk_sndbuf or sk_rcvbuf values, as it can lead to various memory
corruptions, crashes, OOM...

Note that before commit 82981930 ("net: cleanups in
sock_setsockopt()"), the bug was even more serious, since SO_SNDBUF
and SO_RCVBUF were vulnerable.

This needs to be backported to all known linux kernels.

Again, many thanks to syzkaller team for discovering this gem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

geneve{,6}_build_skb can end up doing a pskb_expand_head(), which
makes the ip_hdr(skb) reference we stashed earlier stale. Since it's
only needed as an argument to ip_tunnel_ecn_encap(), move this
directly in the function call.

Fixes: 08399efc ("geneve: ensure ECN info is handled properly in all tx/rx paths")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Qian Zhang (张谦) reported a potential socket buffer overflow in
tipc_msg_build() which is also known as CVE-2016-8632: due to
insufficient checks, a buffer overflow can occur if MTU is too short for
even tipc headers. As anyone can set device MTU in a user/net namespace,
this issue can be abused by a regular user.

As agreed in the discussion on Ben Hutchings' original patch, we should
check the MTU at the moment a bearer is attached rather than for each
processed packet. We also need to repeat the check when bearer MTU is
adjusted to new device MTU. UDP case also needs a check to avoid
overflow when calculating bearer MTU.

Fixes: b97bf3fd ("[TIPC] Initial merge")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reported-by: Qian Zhang (张谦) <zhangqian-c@360.cn>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.9-20161201' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2016-12-02

this is a pull request for net/master.

There are two patches by Stephane Grosjean, who adds support for the new
PCAN-USB X6 USB interface to the pcan_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

We want to set the other "err" variable here so that we can return it
later.  My version of GCC misses this issue but I caught it with a
static checker.

Fixes: 9f70eb33 ("net: ethernet: renesas: ravb: fix fixed-link phydev leaks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

When streaming a lot of data and the RZ/A1 can't keep up, some status bits
will get set that are not being checked or cleared which cause the
following messages and the Ethernet driver to stop working. This
patch fixes that issue.

irq 21: nobody cared (try booting with the "irqpoll" option)
handlers:
[<c036b71c>] sh_eth_interrupt
Disabling IRQ #21

Fixes: db893473 ("sh_eth: Add support for r7s72100")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

__bcmgenet_tx_reclaim() and bcmgenet_free_rx_buffers() are not using the
same struct device during unmap that was used for the map operation,
which makes DMA-API debugging warn about it. Fix this by always using
&priv->pdev->dev throughout the driver, using an identical device
reference for all map/unmap calls.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ozgur Karatas reported that the very first entry in the CREDITS file had
the wrong tag for name (M: instead of N: - it happened when moving the
entry from the MAINTAINERS file, where 'M:' stands for "Maintainer").

And when I went looking, I found a couple of other cases of wrong
tagging too.
Reported-by: Ozgur Karatas <mueddib@yandex.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This patch adds support for PID 0x1040 of Telit LE922A.

The qmi adapter requires to have DTR set for proper working,
so QMI_WWAN_QUIRK_DTR has been enabled.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit bfe9b9d2 ("cdc_ether: Improve ZTE MF823/831/910 handling")
introduced a work-around in usbnet_cdc_status() for devices that exported
cdc carrier on twice on connect. Before the commit, this behavior caused
the link state to be incorrect. It was assumed that all CDC Ethernet
devices would either export this behavior, or send one off and then one on
notification (which seems to be the default behavior).

Unfortunately, it turns out multiple devices sends a connection
notification multiple times per second (via an interrupt), even when
connection state does not change. This has been observed with several
different USB LAN dongles (at least), for example 13b1:0041 (Linksys).
After bfe9b9d2, the link state has been set as down and then up for
each notification. This has caused a flood of Netlink NEWLINK messages and
syslog to be flooded with messages similar to:

cdc_ether 2-1:2.0 eth1: kevent 12 may have been dropped

This commit fixes the behavior by reverting usbnet_cdc_status() to how it
was before bfe9b9d2. The work-around has been moved to a separate
status-function which is only called when a known, affect device is
detected.

v1->v2:

* Do not open-code netif_carrier_ok() (thanks Henning Schild).
* Call netif_carrier_off() instead of usb_link_change(). This prevents
calling schedule_work() twice without giving the work queue a chance to be
processed (thanks Bjørn Mork).

Fixes: bfe9b9d2 ("cdc_ether: Improve ZTE MF823/831/910 handling")
Reported-by: Henning Schild <henning.schild@siemens.com>
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>