Skip to content

L
linux
Switch branch/tag
  1. 11 Mar, 2016 16 commits
  3. 10 Mar, 2016 4 commits
    • Peter Chen's avatar
      usb: chipidea: otg: change workqueue ci_otg as freezable · e4477a4b
      Peter Chen authored 
      [ Upstream commit d144dfea ]

If we use USB ID pin as wakeup source, and there is a USB block
device on this USB OTG (ID) cable, the system will be deadlock
after system resume.

The root cause for this problem is: the workqueue ci_otg may try
to remove hcd before the driver resume has finished, and hcd will
disconnect the device on it, then, it will call device_release_driver,
and holds the device lock "dev->mutex", but it is never unlocked since
it waits workqueue writeback to run to flush the block information, but
the workqueue writeback is freezable, it is not thawed before driver
resume has finished.

When the driver (device: sd 0:0:0:0:) resume goes to dpm_complete, it
tries to get its device lock "dev->mutex", but it can't get it forever,
then the deadlock occurs. Below call stacks show the situation.

So, in order to fix this problem, we need to change workqueue ci_otg
as freezable, then the work item in this workqueue will be run after
driver's resume, this workqueue will not be blocked forever like above
case since the workqueue writeback has been thawed too.

Tested at: i.mx6qdl-sabresd and i.mx6sx-sdb.

[  555.178869] kworker/u2:13   D c07de74c     0   826      2 0x00000000
[  555.185310] Workqueue: ci_otg ci_otg_work
[  555.189353] Backtrace:
[  555.191849] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0)
[  555.198912]  r10:ee471ba0 r9:00000000 r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4
[  555.206867]  r4:ee470000
[  555.209453] [<c07dec24>] (schedule) from [<c07e2fc4>] (schedule_timeout+0x15c/0x1e0)
[  555.217212]  r4:7fffffff r3:edc2b000
[  555.220862] [<c07e2e68>] (schedule_timeout) from [<c07df6c8>] (wait_for_common+0x94/0x144)
[  555.229140]  r8:00000000 r7:00000002 r6:ee470000 r5:ee471ba4 r4:7fffffff
[  555.235980] [<c07df634>] (wait_for_common) from [<c07df790>] (wait_for_completion+0x18/0x1c)
[  555.244430]  r10:00000001 r9:c0b5563c r8:c0042e48 r7:ef086000 r6:eea4372c r5:ef131b00
[  555.252383]  r4:00000000
[  555.254970] [<c07df778>] (wait_for_completion) from [<c0043cb8>] (flush_work+0x19c/0x234)
[  555.263177] [<c0043b1c>] (flush_work) from [<c0043fac>] (flush_delayed_work+0x48/0x4c)
[  555.271106]  r8:ed5b5000 r7:c0b38a3c r6:eea439cc r5:eea4372c r4:eea4372c
[  555.277958] [<c0043f64>] (flush_delayed_work) from [<c00eae18>] (bdi_unregister+0x84/0xec)
[  555.286236]  r4:eea43520 r3:20000153
[  555.289885] [<c00ead94>] (bdi_unregister) from [<c02c2154>] (blk_cleanup_queue+0x180/0x29c)
[  555.298250]  r5:eea43808 r4:eea43400
[  555.301909] [<c02c1fd4>] (blk_cleanup_queue) from [<c0417914>] (__scsi_remove_device+0x48/0xb8)
[  555.310623]  r7:00000000 r6:20000153 r5:ededa950 r4:ededa800
[  555.316403] [<c04178cc>] (__scsi_remove_device) from [<c0415e90>] (scsi_forget_host+0x64/0x68)
[  555.325028]  r5:ededa800 r4:ed5b5000
[  555.328689] [<c0415e2c>] (scsi_forget_host) from [<c0409828>] (scsi_remove_host+0x78/0x104)
[  555.337054]  r5:ed5b5068 r4:ed5b5000
[  555.340709] [<c04097b0>] (scsi_remove_host) from [<c04cdfcc>] (usb_stor_disconnect+0x50/0xb4)
[  555.349247]  r6:ed5b56e4 r5:ed5b5818 r4:ed5b5690 r3:00000008
[  555.355025] [<c04cdf7c>] (usb_stor_disconnect) from [<c04b3bc8>] (usb_unbind_interface+0x78/0x25c)
[  555.363997]  r8:c13919b4 r7:edd3c000 r6:edd3c020 r5:ee551c68 r4:ee551c00 r3:c04cdf7c
[  555.371892] [<c04b3b50>] (usb_unbind_interface) from [<c03dc248>] (__device_release_driver+0x8c/0x118)
[  555.381213]  r10:00000001 r9:edd90c00 r8:c13919b4 r7:ee551c68 r6:c0b546e0 r5:c0b5563c
[  555.389167]  r4:edd3c020
[  555.391752] [<c03dc1bc>] (__device_release_driver) from [<c03dc2fc>] (device_release_driver+0x28/0x34)
[  555.401071]  r5:edd3c020 r4:edd3c054
[  555.404721] [<c03dc2d4>] (device_release_driver) from [<c03db304>] (bus_remove_device+0xe0/0x110)
[  555.413607]  r5:edd3c020 r4:ef17f04c
[  555.417253] [<c03db224>] (bus_remove_device) from [<c03d8128>] (device_del+0x114/0x21c)
[  555.425270]  r6:edd3c028 r5:edd3c020 r4:ee551c00 r3:00000000
[  555.431045] [<c03d8014>] (device_del) from [<c04b1560>] (usb_disable_device+0xa4/0x1e8)
[  555.439061]  r8:edd3c000 r7:eded8000 r6:00000000 r5:00000001 r4:ee551c00
[  555.445906] [<c04b14bc>] (usb_disable_device) from [<c04a8e54>] (usb_disconnect+0x74/0x224)
[  555.454271]  r9:edd90c00 r8:ee551000 r7:ee551c68 r6:ee551c9c r5:ee551c00 r4:00000001
[  555.462156] [<c04a8de0>] (usb_disconnect) from [<c04a8fb8>] (usb_disconnect+0x1d8/0x224)
[  555.470259]  r10:00000001 r9:edd90000 r8:ee471e2c r7:ee551468 r6:ee55149c r5:ee551400
[  555.478213]  r4:00000001
[  555.480797] [<c04a8de0>] (usb_disconnect) from [<c04ae5ec>] (usb_remove_hcd+0xa0/0x1ac)
[  555.488813]  r10:00000001 r9:ee471eb0 r8:00000000 r7:ef3d9500 r6:eded810c r5:eded80b0
[  555.496765]  r4:eded8000
[  555.499351] [<c04ae54c>] (usb_remove_hcd) from [<c04d4158>] (host_stop+0x28/0x64)
[  555.506847]  r6:eeb50010 r5:eded8000 r4:eeb51010
[  555.511563] [<c04d4130>] (host_stop) from [<c04d09b8>] (ci_otg_work+0xc4/0x124)
[  555.518885]  r6:00000001 r5:eeb50010 r4:eeb502a0 r3:c04d4130
[  555.524665] [<c04d08f4>] (ci_otg_work) from [<c00454f0>] (process_one_work+0x194/0x420)
[  555.532682]  r6:ef086000 r5:eeb502a0 r4:edc44480
[  555.537393] [<c004535c>] (process_one_work) from [<c00457b0>] (worker_thread+0x34/0x514)
[  555.545496]  r10:edc44480 r9:ef086000 r8:c0b1a100 r7:ef086034 r6:00000088 r5:edc44498
[  555.553450]  r4:ef086000
[  555.556032] [<c004577c>] (worker_thread) from [<c004bab4>] (kthread+0xdc/0xf8)
[  555.563268]  r10:00000000 r9:00000000 r8:00000000 r7:c004577c r6:edc44480 r5:eddc15c0
[  555.571221]  r4:00000000
[  555.573804] [<c004b9d8>] (kthread) from [<c000fef0>] (ret_from_fork+0x14/0x24)
[  555.581040]  r7:00000000 r6:00000000 r5:c004b9d8 r4:eddc15c0

[  553.429383] sh              D c07de74c     0   694    691 0x00000000
[  553.435801] Backtrace:
[  553.438295] [<c07de4fc>] (__schedule) from [<c07dec6c>] (schedule+0x48/0xa0)
[  553.445358]  r10:edd3c054 r9:edd3c078 r8:edddbd50 r7:edcbbc00 r6:c1377c34 r5:60000153
[  553.453313]  r4:eddda000
[  553.455896] [<c07dec24>] (schedule) from [<c07deff8>] (schedule_preempt_disabled+0x10/0x14)
[  553.464261]  r4:edd3c058 r3:0000000a
[  553.467910] [<c07defe8>] (schedule_preempt_disabled) from [<c07e0bbc>] (mutex_lock_nested+0x1a0/0x3e8)
[  553.477254] [<c07e0a1c>] (mutex_lock_nested) from [<c03e927c>] (dpm_complete+0xc0/0x1b0)
[  553.485358]  r10:00561408 r9:edd3c054 r8:c0b4863c r7:edddbd90 r6:c0b485d8 r5:edd3c020
[  553.493313]  r4:edd3c0d0
[  553.495896] [<c03e91bc>] (dpm_complete) from [<c03e9388>] (dpm_resume_end+0x1c/0x20)
[  553.503652]  r9:00000000 r8:c0b1a9d0 r7:c1334ec0 r6:c1334edc r5:00000003 r4:00000010
[  553.511544] [<c03e936c>] (dpm_resume_end) from [<c0079894>] (suspend_devices_and_enter+0x158/0x504)
[  553.520604]  r4:00000000 r3:c1334efc
[  553.524250] [<c007973c>] (suspend_devices_and_enter) from [<c0079e74>] (pm_suspend+0x234/0x2cc)
[  553.532961]  r10:00561408 r9:ed6b7300 r8:00000004 r7:c1334eec r6:00000000 r5:c1334ee8
[  553.540914]  r4:00000003
[  553.543493] [<c0079c40>] (pm_suspend) from [<c0078a6c>] (state_store+0x6c/0xc0)

[  555.703684] 7 locks held by kworker/u2:13/826:
[  555.708140]  #0:  ("%s""ci_otg"){++++.+}, at: [<c0045484>] process_one_work+0x128/0x420
[  555.716277]  #1:  ((&ci->work)){+.+.+.}, at: [<c0045484>] process_one_work+0x128/0x420
[  555.724317]  #2:  (usb_bus_list_lock){+.+.+.}, at: [<c04ae5e4>] usb_remove_hcd+0x98/0x1ac
[  555.732626]  #3:  (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224
[  555.740403]  #4:  (&dev->mutex){......}, at: [<c04a8e28>] usb_disconnect+0x48/0x224
[  555.748179]  #5:  (&dev->mutex){......}, at: [<c03dc2f4>] device_release_driver+0x20/0x34
[  555.756487]  #6:  (&shost->scan_mutex){+.+.+.}, at: [<c04097d0>] scsi_remove_host+0x20/0x104

Cc: <stable@vger.kernel.org> #v3.14+
Cc: Jun Li <jun.li@nxp.com>
Signed-off-by: default avatarPeter Chen <peter.chen@nxp.com>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      e4477a4b
    • Ilya Dryomov's avatar
      libceph: don't bail early from try_read() when skipping a message · 34251e49
      Ilya Dryomov authored 
      [ Upstream commit e7a88e82 ]

The contract between try_read() and try_write() is that when called
each processes as much data as possible.  When instructed by osd_client
to skip a message, try_read() is violating this contract by returning
after receiving and discarding a single message instead of checking for
more.  try_write() then gets a chance to write out more requests,
generating more replies/skips for try_read() to handle, forcing the
messenger into a starvation loop.

Cc: stable@vger.kernel.org # 3.10+
Reported-by: default avatarVarada Kari <Varada.Kari@sandisk.com>
Signed-off-by: default avatarIlya Dryomov <idryomov@gmail.com>
Tested-by: default avatarVarada Kari <Varada.Kari@sandisk.com>
Reviewed-by: default avatarAlex Elder <elder@linaro.org>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      34251e49
    • Steven Rostedt (Red Hat)'s avatar
      tracing: Fix showing function event in available_events · 9c8b0ac7
      Steven Rostedt (Red Hat) authored 
      [ Upstream commit d045437a ]

The ftrace:function event is only displayed for parsing the function tracer
data. It is not used to enable function tracing, and does not include an
"enable" file in its event directory.

Originally, this event was kept separate from other events because it did
not have a ->reg parameter. But perf added a "reg" parameter for its use
which caused issues, because it made the event available to functions where
it was not compatible for.

Commit 9b63776f "tracing: Do not enable function event with enable"
added a TRACE_EVENT_FL_IGNORE_ENABLE flag that prevented the function event
from being enabled by normal trace events. But this commit missed keeping
the function event from being displayed by the "available_events" directory,
which is used to show what events can be enabled by set_event.

One documented way to enable all events is to:

 cat available_events > set_event

But because the function event is displayed in the available_events, this
now causes an INVALID error:

 cat: write error: Invalid argument
Reported-by: default avatarChunyu Hu <chuhu@redhat.com>
Fixes: 9b63776f "tracing: Do not enable function event with enable"
Cc: stable@vger.kernel.org # 3.4+
Signed-off-by: default avatarSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      9c8b0ac7
    • Christian Borntraeger's avatar
      KVM: async_pf: do not warn on page allocation failures · e0b898dc
      Christian Borntraeger authored 
      [ Upstream commit d7444794 ]

In async_pf we try to allocate with NOWAIT to get an element quickly
or fail. This code also handle failures gracefully. Lets silence
potential page allocation failures under load.

qemu-system-s39: page allocation failure: order:0,mode:0x2200000
[...]
Call Trace:
([<00000000001146b8>] show_trace+0xf8/0x148)
[<000000000011476a>] show_stack+0x62/0xe8
[<00000000004a36b8>] dump_stack+0x70/0x98
[<0000000000272c3a>] warn_alloc_failed+0xd2/0x148
[<000000000027709e>] __alloc_pages_nodemask+0x94e/0xb38
[<00000000002cd36a>] new_slab+0x382/0x400
[<00000000002cf7ac>] ___slab_alloc.constprop.30+0x2dc/0x378
[<00000000002d03d0>] kmem_cache_alloc+0x160/0x1d0
[<0000000000133db4>] kvm_setup_async_pf+0x6c/0x198
[<000000000013dee8>] kvm_arch_vcpu_ioctl_run+0xd48/0xd58
[<000000000012fcaa>] kvm_vcpu_ioctl+0x372/0x690
[<00000000002f66f6>] do_vfs_ioctl+0x3be/0x510
[<00000000002f68ec>] SyS_ioctl+0xa4/0xb8
[<0000000000781c5e>] system_call+0xd6/0x264
[<000003ffa24fa06a>] 0x3ffa24fa06a

Cc: stable@vger.kernel.org
Signed-off-by: default avatarChristian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: default avatarDominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: default avatarPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      e0b898dc
  5. 08 Mar, 2016 20 commits
    • Mark Rutland's avatar
      KVM: arm/arm64: vgic: Ensure bitmaps are long enough · e720b3ba
      Mark Rutland authored 
      [ Upstream commit 236cf17c ]

When we allocate bitmaps in vgic_vcpu_init_maps, we divide the number of
bits we need by 8 to figure out how many bytes to allocate. However,
bitmap elements are always accessed as unsigned longs, and if we didn't
happen to allocate a size such that size % sizeof(unsigned long) == 0,
bitmap accesses may go past the end of the allocation.

When using KASAN (which does byte-granular access checks), this results
in a continuous stream of BUGs whenever these bitmaps are accessed:

=============================================================================
BUG kmalloc-128 (Tainted: G    B          ): kasan: bad access detected
-----------------------------------------------------------------------------

INFO: Allocated in vgic_init.part.25+0x55c/0x990 age=7493 cpu=3 pid=1730
INFO: Slab 0xffffffbde6d5da40 objects=16 used=15 fp=0xffffffc935769700 flags=0x4000000000000080
INFO: Object 0xffffffc935769500 @offset=1280 fp=0x          (null)

Bytes b4 ffffffc9357694f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769510: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769520: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769530: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769540: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769550: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769560: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Object ffffffc935769570: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
Padding ffffffc9357695f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00  ................
CPU: 3 PID: 1740 Comm: kvm-vcpu-0 Tainted: G    B           4.4.0+ #17
Hardware name: ARM Juno development board (r1) (DT)
Call trace:
[<ffffffc00008e770>] dump_backtrace+0x0/0x280
[<ffffffc00008ea04>] show_stack+0x14/0x20
[<ffffffc000726360>] dump_stack+0x100/0x188
[<ffffffc00030d324>] print_trailer+0xfc/0x168
[<ffffffc000312294>] object_err+0x3c/0x50
[<ffffffc0003140fc>] kasan_report_error+0x244/0x558
[<ffffffc000314548>] __asan_report_load8_noabort+0x48/0x50
[<ffffffc000745688>] __bitmap_or+0xc0/0xc8
[<ffffffc0000d9e44>] kvm_vgic_flush_hwstate+0x1bc/0x650
[<ffffffc0000c514c>] kvm_arch_vcpu_ioctl_run+0x2ec/0xa60
[<ffffffc0000b9a6c>] kvm_vcpu_ioctl+0x474/0xa68
[<ffffffc00036b7b0>] do_vfs_ioctl+0x5b8/0xcb0
[<ffffffc00036bf34>] SyS_ioctl+0x8c/0xa0
[<ffffffc000086cb0>] el0_svc_naked+0x24/0x28
Memory state around the buggy address:
 ffffffc935769400: 00 00 fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffffffc935769480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
>ffffffc935769500: 04 fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
                   ^
 ffffffc935769580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
 ffffffc935769600: 00 00 00 00 fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================

Fix the issue by always allocating a multiple of sizeof(unsigned long),
as we do elsewhere in the vgic code.

Fixes: c1bfb577 ("arm/arm64: KVM: vgic: switch to dynamic allocation")
Cc: stable@vger.kernel.org
Acked-by: default avatarMarc Zyngier <marc.zyngier@arm.com>
Acked-by: default avatarChristoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: default avatarMark Rutland <mark.rutland@arm.com>
Signed-off-by: default avatarMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      e720b3ba
    • Stefan Hajnoczi's avatar
      sunrpc/cache: fix off-by-one in qword_get() · 7459f09b
      Stefan Hajnoczi authored 
      [ Upstream commit b7052cd7 ]

The qword_get() function NUL-terminates its output buffer.  If the input
string is in hex format \xXXXX... and the same length as the output
buffer, there is an off-by-one:

  int qword_get(char **bpp, char *dest, int bufsize)
  {
      ...
      while (len < bufsize) {
          ...
          *dest++ = (h << 4) | l;
          len++;
      }
      ...
      *dest = '\0';
      return len;
  }

This patch ensures the NUL terminator doesn't fall outside the output
buffer.
Signed-off-by: default avatarStefan Hajnoczi <stefanha@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: default avatarJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      7459f09b
    • Alex Deucher's avatar
      drm/radeon/pm: adjust display configuration after powerstate · ae5a9780
      Alex Deucher authored 
      [ Upstream commit 39d42750 ]

set_power_state defaults to no displays, so we need to update
the display configuration after setting up the powerstate on the
first call. In most cases this is not an issue since ends up
getting called multiple times at any given modeset and the proper
order is achieved in the display changed handling at the top of
the function.
Reviewed-by: default avatarChristian König <christian.koenig@amd.com>
Acked-by: default avatarJordan Lazare <Jordan.Lazare@amd.com>
Signed-off-by: default avatarAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      ae5a9780
    • Martin Schwidefsky's avatar
      s390/compat: correct restore of high gprs on signal return · f5054278
      Martin Schwidefsky authored 
      [ Upstream commit 342300cc ]

git commit 80703617
"s390: add support for vector extension"
broke 31-bit compat processes in regard to signal handling.

The restore_sigregs_ext32() function is used to restore the additional
elements from the user space signal frame. Among the additional elements
are the upper registers halves for 64-bit register support for 31-bit
processes. The copy_from_user that is used to retrieve the high-gprs
array from the user stack uses an incorrect length, 8 bytes instead of
64 bytes. This causes incorrect upper register halves to get loaded.

Cc: stable@vger.kernel.org # 3.8+
Signed-off-by: default avatarMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      f5054278
    • Gerhard Uttenthaler's avatar
      can: ems_usb: Fix possible tx overflow · 2992a0a3
      Gerhard Uttenthaler authored 
      [ Upstream commit 90cfde46 ]

This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.
Signed-off-by: default avatarGerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: default avatarMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      2992a0a3
    • Peter Rosin's avatar
      hwmon: (ads1015) Handle negative conversion values correctly · 9ebc9c53
      Peter Rosin authored 
      [ Upstream commit acc14694 ]

Make the divisor signed as DIV_ROUND_CLOSEST is undefined for negative
dividends when the divisor is unsigned.
Signed-off-by: default avatarPeter Rosin <peda@axentia.se>
Cc: stable@vger.kernel.org
Signed-off-by: default avatarGuenter Roeck <linux@roeck-us.net>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      9ebc9c53
    • Alexandra Yates's avatar
      Adding Intel Lewisburg device IDs for SATA · 0b17b1b0
      Alexandra Yates authored 
      [ Upstream commit f5bdd66c ]

This patch complements the list of device IDs previously
added for lewisburg sata.
Signed-off-by: default avatarAlexandra Yates <alexandra.yates@linux.intel.com>
Signed-off-by: default avatarTejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      0b17b1b0
    • Alexandra Yates's avatar
      ahci: Order SATA device IDs for codename Lewisburg · 1c522e28
      Alexandra Yates authored 
      [ Upstream commit 4d92f009 ]

This change was to preserve the ascending order of device IDs.
There was an exception with the first two Lewisburg device IDs to
keep all device IDs of the same kind grouped by code name.
Signed-off-by: default avatarAlexandra Yates <alexandra.yates@linux.intel.com>
signed-off-by: default avatarTejun Heo <tj@kernel.org>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      1c522e28
    • Bjørn Mork's avatar
      USB: option: add "4G LTE usb-modem U901" · a7da79b1
      Bjørn Mork authored 
      [ Upstream commit d061c1ca ]

Thomas reports:

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=  4 Spd=480 MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=05c6 ProdID=6001 Rev=00.00
S:  Manufacturer=USB Modem
S:  Product=USB Modem
S:  SerialNumber=1234567890ABCDEF
C:  #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:  If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:  If#= 4 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage

Cc: <stable@vger.kernel.org>
Reported-by: default avatarThomas Schäfer <tschaefer@t-online.de>
Signed-off-by: default avatarBjørn Mork <bjorn@mork.no>
Signed-off-by: default avatarJohan Hovold <johan@kernel.org>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      a7da79b1
    • Barry Grussling's avatar
      usb: cp210x support SEL C662 Vendor/Device · b8f42d68
      Barry Grussling authored 
      [ Upstream commit b579fa52 ]

This patch adds support for the Schweitzer Engineering Laboratories
C662 USB cable based off the CP210x driver.
Signed-off-by: default avatarBarry Grussling <barry@grussling.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      b8f42d68
    • Ken Lin's avatar
      USB: cp210x: add IDs for GE B650V3 and B850V3 boards · 12690f70
      Ken Lin authored 
      [ Upstream commit 6627ae19 ]

Add USB ID for cp2104/5 devices on GE B650v3 and B850v3 boards.
Signed-off-by: default avatarKen Lin <ken.lin@advantech.com.tw>
Signed-off-by: default avatarAkshay Bhat <akshay.bhat@timesys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarJohan Hovold <johan@kernel.org>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      12690f70
    • Oliver Freyermuth's avatar
      USB: cp210x: add ID for ELV Marble Sound Board 1 · 83598dff
      Oliver Freyermuth authored 
      [ Upstream commit f7d7f59a ]

Add the USB device ID for ELV Marble Sound Board 1.
Signed-off-by: default avatarOliver Freyermuth <o.freyermuth@googlemail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarJohan Hovold <johan@kernel.org>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      83598dff
    • Andrey Skvortsov's avatar
      USB: option: add support for SIM7100E · 6034ffbd
      Andrey Skvortsov authored 
      [ Upstream commit 3158a8d4 ]

$ lsusb:
Bus 001 Device 101: ID 1e0e:9001 Qualcomm / Option

$ usb-devices:
T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=101 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  2
P:  Vendor=1e0e ProdID=9001 Rev= 2.32
S:  Manufacturer=SimTech, Incorporated
S:  Product=SimTech, Incorporated
S:  SerialNumber=0123456789ABCDEF
C:* #Ifs= 7 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I:* If#= 6 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=42 Prot=01 Driver=(none)

The last interface (6) is used for Android Composite ADB interface.

Serial port layout:
0: QCDM/DIAG
1: NMEA
2: AT
3: AT/PPP
4: audio
Signed-off-by: default avatarAndrey Skvortsov <andrej.skvortzov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: default avatarJohan Hovold <johan@kernel.org>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      6034ffbd
    • Benjamin Coddington's avatar
      NFSv4: Fix a dentry leak on alias use · 655ea615
      Benjamin Coddington authored 
      [ Upstream commit d9dfd8d7 ]

In the case where d_add_unique() finds an appropriate alias to use it will
have already incremented the reference count.  An additional dget() to swap
the open context's dentry is unnecessary and will leak a reference.
Signed-off-by: default avatarBenjamin Coddington <bcodding@redhat.com>
Fixes: 275bb307 ("NFSv4: Move dentry instantiation into the NFSv4-...")
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: default avatarTrond Myklebust <trond.myklebust@primarydata.com>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      655ea615
    • John Youn's avatar
      usb: dwc3: Fix assignment of EP transfer resources · 174bf25d
      John Youn authored 
      [ Upstream commit c4509601 ]

The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda618 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.

The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:

1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.

2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).

The following simplified method is used instead:

All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.

This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.

Fixes: aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Cc: <stable@vger.kernel.org> # v3.2+
Reported-by: default avatarRavi Babu <ravibabu@ti.com>
Signed-off-by: default avatarJohn Youn <johnyoun@synopsys.com>
Signed-off-by: default avatarFelipe Balbi <balbi@kernel.org>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      174bf25d
    • Hans Verkuil's avatar
      [media] adv7604: fix tx 5v detect regression · 39870068
      Hans Verkuil authored 
      [ Upstream commit 0ba4581c ]

The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: default avatarHans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org>      # for v3.14 and up
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      39870068
    • Konrad Rzeszutek Wilk's avatar
      xen/pcifront: Fix mysterious crashes when NUMA locality information was extracted. · 39d8d5a0
      Konrad Rzeszutek Wilk authored 
      [ Upstream commit 4d8c8bd6 ]

Occasionaly PV guests would crash with:

pciback 0000:00:00.1: Xen PCI mapped GSI0 to IRQ16
BUG: unable to handle kernel paging request at 0000000d1a8c0be0
.. snip..
  <ffffffff8139ce1b>] find_next_bit+0xb/0x10
  [<ffffffff81387f22>] cpumask_next_and+0x22/0x40
  [<ffffffff813c1ef8>] pci_device_probe+0xb8/0x120
  [<ffffffff81529097>] ? driver_sysfs_add+0x77/0xa0
  [<ffffffff815293e4>] driver_probe_device+0x1a4/0x2d0
  [<ffffffff813c1ddd>] ? pci_match_device+0xdd/0x110
  [<ffffffff81529657>] __device_attach_driver+0xa7/0xb0
  [<ffffffff815295b0>] ? __driver_attach+0xa0/0xa0
  [<ffffffff81527622>] bus_for_each_drv+0x62/0x90
  [<ffffffff8152978d>] __device_attach+0xbd/0x110
  [<ffffffff815297fb>] device_attach+0xb/0x10
  [<ffffffff813b75ac>] pci_bus_add_device+0x3c/0x70
  [<ffffffff813b7618>] pci_bus_add_devices+0x38/0x80
  [<ffffffff813dc34e>] pcifront_scan_root+0x13e/0x1a0
  [<ffffffff817a0692>] pcifront_backend_changed+0x262/0x60b
  [<ffffffff814644c6>] ? xenbus_gather+0xd6/0x160
  [<ffffffff8120900f>] ? put_object+0x2f/0x50
  [<ffffffff81465c1d>] xenbus_otherend_changed+0x9d/0xa0
  [<ffffffff814678ee>] backend_changed+0xe/0x10
  [<ffffffff81463a28>] xenwatch_thread+0xc8/0x190
  [<ffffffff810f22f0>] ? woken_wake_function+0x10/0x10

which was the result of two things:

When we call pci_scan_root_bus we would pass in 'sd' (sysdata)
pointer which was an 'pcifront_sd' structure. However in the
pci_device_add it expects that the 'sd' is 'struct sysdata' and
sets the dev->node to what is in sd->node (offset 4):

set_dev_node(&dev->dev, pcibus_to_node(bus));

 __pcibus_to_node(const struct pci_bus *bus)
{
        const struct pci_sysdata *sd = bus->sysdata;

        return sd->node;
}

However our structure was pcifront_sd which had nothing at that
offset:

struct pcifront_sd {
        int                        domain;    /*     0     4 */
        /* XXX 4 bytes hole, try to pack */
        struct pcifront_device *   pdev;      /*     8     8 */
}

That is an hole - filled with garbage as we used kmalloc instead of
kzalloc (the second problem).

This patch fixes the issue by:
 1) Use kzalloc to initialize to a well known state.
 2) Put 'struct pci_sysdata' at the start of 'pcifront_sd'. That
    way access to the 'node' will access the right offset.
Signed-off-by: default avatarKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: default avatarBoris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: default avatarDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      39d8d5a0
    • Konrad Rzeszutek Wilk's avatar
      xen/pciback: Don't allow MSI-X ops if PCI_COMMAND_MEMORY is not set. · 3d0ec7c0
      Konrad Rzeszutek Wilk authored 
      [ Upstream commit 408fb0e5 ]

commit f598282f ("PCI: Fix the NIU MSI-X problem in a better way")
teaches us that dealing with MSI-X can be troublesome.

Further checks in the MSI-X architecture shows that if the
PCI_COMMAND_MEMORY bit is turned of in the PCI_COMMAND we
may not be able to access the BAR (since they are memory regions).

Since the MSI-X tables are located in there.. that can lead
to us causing PCIe errors. Inhibit us performing any
operation on the MSI-X unless the MEMORY bit is set.

Note that Xen hypervisor with:
"x86/MSI-X: access MSI-X table only after having enabled MSI-X"
will return:
xen_pciback: 0000:0a:00.1: error -6 enabling MSI-X for guest 3!

When the generic MSI code tries to setup the PIRQ without
MEMORY bit set. Which means with later versions of Xen
(4.6) this patch is not neccessary.

This is part of XSA-157

CC: stable@vger.kernel.org
Reviewed-by: default avatarJan Beulich <jbeulich@suse.com>
Signed-off-by: default avatarKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      3d0ec7c0
    • Konrad Rzeszutek Wilk's avatar
      xen/pciback: Return error on XEN_PCI_OP_enable_msix when device has MSI or MSI-X enabled · f4993f38
      Konrad Rzeszutek Wilk authored 
      [ Upstream commit 5e0ce145 ]

The guest sequence of:

  a) XEN_PCI_OP_enable_msix
  b) XEN_PCI_OP_enable_msix

results in hitting an NULL pointer due to using freed pointers.

The device passed in the guest MUST have MSI-X capability.

The a) constructs and SysFS representation of MSI and MSI groups.
The b) adds a second set of them but adding in to SysFS fails (duplicate entry).
'populate_msi_sysfs' frees the newly allocated msi_irq_groups (note that
in a) pdev->msi_irq_groups is still set) and also free's ALL of the
MSI-X entries of the device (the ones allocated in step a) and b)).

The unwind code: 'free_msi_irqs' deletes all the entries and tries to
delete the pdev->msi_irq_groups (which hasn't been set to NULL).
However the pointers in the SysFS are already freed and we hit an
NULL pointer further on when 'strlen' is attempted on a freed pointer.

The patch adds a simple check in the XEN_PCI_OP_enable_msix to guard
against that. The check for msi_enabled is not stricly neccessary.

This is part of XSA-157

CC: stable@vger.kernel.org
Reviewed-by: default avatarDavid Vrabel <david.vrabel@citrix.com>
Reviewed-by: default avatarJan Beulich <jbeulich@suse.com>
Signed-off-by: default avatarKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      f4993f38
    • Konrad Rzeszutek Wilk's avatar
      xen/pciback: Save xen_pci_op commands before processing it · c801e64a
      Konrad Rzeszutek Wilk authored 
      [ Upstream commit 8135cf8b ]

Double fetch vulnerabilities that happen when a variable is
fetched twice from shared memory but a security check is only
performed the first time.

The xen_pcibk_do_op function performs a switch statements on the op->cmd
value which is stored in shared memory. Interestingly this can result
in a double fetch vulnerability depending on the performed compiler
optimization.

This patch fixes it by saving the xen_pci_op command before
processing it. We also use 'barrier' to make sure that the
compiler does not perform any optimization.

This is part of XSA155.

CC: stable@vger.kernel.org
Reviewed-by: default avatarKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: default avatarJan Beulich <JBeulich@suse.com>
Signed-off-by: default avatarDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: default avatarKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: default avatarSasha Levin <sasha.levin@oracle.com>
      c801e64a
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7