The i2c_client received in probe() should not be kfree()'d.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Accessing num_reg elements in the interval [reg .. reg+num_regs)
is permitted if (reg+numregs <= array size), so barf when that
excluded upper bound is > array size. The prior -1 would give
access to one too many elements.
Signed-off-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The touch screen controller in the TPS6507x chip needs values that are
dependent on the characteristics of the touch screen hardware being used
in the board design.  In addition, the board provides version information
that is exposed via the kernel input sub-system.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The charger interrupts on the WM831x are unconditionally a wake source
for the system. If the power driver is not able to monitor them (for
example, due to the IRQ line not having been wired up on the system)
then any charger interrupt will prevent the system suspending for any
meaningful amount of time since nothing will ack them.

Avoid this issue by manually acknowledging these interrupts when we
suspend the WM831x core device if they are masked. If software is
actually using the interrupts then they will be unmasked and this
change will have no effect.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Ensure that the hardware has interrupts masked if we are not using
the interrupt controller on the WM831x by initialising the masks
before we check for the setup data required for the IRQ line. This
avoids signalling an unused IRQ line and improves the robustness
of checks that the IRQ is in use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add touch screen input driver for TPS6507x family of multi-function
chips.  Uses the TPS6507x MFD driver.  No interrupt support due to
testing limitations of current hardware.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

TPS6507x are multi function (PM, touchscreen) chipsets from TI.
This commit also changes the corresponding regulator driver from being
standalone to an MFD subdevice.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Move from using tps or tsp6507x to tps6057x_pmic in a consistent manner.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add mfd structure which refrences sub-driver initialization data. For example,
for a giving hardware implementation, the voltage regulator sub-driver
initialization data provides the mapping betten a voltage regulator and what
the output voltage is being used for.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Other sub-drivers for the TPS6507x chip will need to use register
definition so move it out of the source file and into a header file.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Implicit slab.h inclusion via percpu.h is about to go away.  Make sure
gfp.h or slab.h is included as necessary.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

Currently completion of WM831x AUXADC conversions is monitored by
checking for convertor enable. Due to the mechanism used to ensure
data corruption is avoided when reading AUXADC data there may under
heavy I/O be a window where this bit has cleared but the conversion
results have not been updated. Data availability is only guaranteed
after the AUXADC data interrupt has been asserted.

Avoid this by always using the interrupt to detect completion. If the
chip IRQ is not set up then we poll the IRQ status register for up to
5ms. If it is set up then we rely on the data done interrupt with a
vastly increased timeout, failing the conversion if the interrupt is
not generated.

This also saves a register read when using interrupts.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The Janz VMOD-TTL is a MODULbus daughterboard which fits onto any MODULbus
carrier board. It essentially consists of some various logic and a Zilog
Z8536 CIO Counter/Timer and Parallel IO Unit.

The board must be physically configured with jumpers to enable a user to
drive output signals. I am only interested in outputs, so I have made this
driver as simple as possible. It only supports a very minimal subset of the
features provided by the Z8536 chip.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The Janz VMOD-ICAN3 is a MODULbus daughterboard which fits onto any
MODULbus carrier board. It is an intelligent CAN controller with a
microcontroller and associated firmware.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The Janz CMOD-IO PCI MODULbus carrier board is a PCI to MODULbus bridge,
which may host many different types of MODULbus daughterboards, including
CAN and GPIO controllers.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Reviewed-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

"pcf->irq_handler" has PCF50633_NUM_IRQ elements.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This was used by the old, pre-genirq IRQ implementation but is no
longer required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Add platform data for timb-dma, and add it in to timb-dma
in all configurations of timberdale.

Also incremented the version number.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch fixes three section mismatches.

WARNING: drivers/mfd/88pm860x.o(.text+0x12): Section mismatch in
reference from the function pm860x_device_exit() to the function
.devexit.text:device_irq_exit()
The function pm860x_device_exit() references a function in an exit
section.
Often the function device_irq_exit() has valid usage outside the exit
section
and the fix is to remove the __devexit annotation of device_irq_exit.

WARNING: drivers/mfd/88pm860x.o(.text+0xb0): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8606_init()
The function pm860x_device_init() references
the function __devinit device_8606_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8606_init is wrong.

WARNING: drivers/mfd/88pm860x.o(.text+0xbe): Section mismatch in
reference from the function pm860x_device_init() to the function
.devinit.text:device_8607_init()
The function pm860x_device_init() references
the function __devinit device_8607_init().
This is often because pm860x_device_init lacks a __devinit
annotation or the annotation of device_8607_init is wrong.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

If mem_base is NULL, then we fall back to the default case, just copying the
original resource.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

I'm pretty sure that it should be + 1 here.  It's an off by one, because
we start counting at zero.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This file is replaced by a cleaner version with the adding of a MFD driver for
the southbridge.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

The RDC321x MFD southbridge driver will pass a reference to the
southbridge PCI device which should be used by the watchdog driver for its
operations.  This patch converts the watchdog driver to use the pci_dev
pointer and make use of the base register resource which is passed along
with the platform device.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch adds a new GPIO driver for the RDC321x SoC GPIO controller.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch adds a new MFD driver for the RDC321x southbridge. This southbridge
is always present in the RDC321x System-on-a-Chip and provides access to some
GPIOs as well as a watchdog. Access to these two functions is done using the
southbridge PCI device configuration space.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Fix I2C-drivers which missed setting clientdata to NULL before freeing the
structure it points to. Also fix drivers which do this _after_ the structure
was freed already.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

This patch adds in the Xilinx I2C bus driver to some of the
configurations of the timberdale MFD.

It provides the I2C devices to the XIIC via platform data in a
similar way as done to the ocores driver.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

We should check for pdata being not NULL before dereferencing it.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>

Merge branch 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (61 commits)
  tracing: Add __used annotation to event variable
  perf, trace: Fix !x86 build bug
  perf report: Support multiple events on the TUI
  perf annotate: Fix up usage of the build id cache
  x86/mmiotrace: Remove redundant instruction prefix checks
  perf annotate: Add TUI interface
  perf tui: Remove annotate from popup menu after failure
  perf report: Don't start the TUI if -D is used
  perf: Fix getline undeclared
  perf: Optimize perf_tp_event_match()
  perf: Remove more code from the fastpath
  perf: Optimize the !vmalloc backed buffer
  perf: Optimize perf_output_copy()
  perf: Fix wakeup storm for RO mmap()s
  perf-record: Share per-cpu buffers
  perf-record: Remove -M
  perf: Ensure that IOC_OUTPUT isn't used to create multi-writer buffers
  perf, trace: Optimize tracepoints by using per-tracepoint-per-cpu hlist to track events
  perf, trace: Optimize tracepoints by removing IRQ-disable from perf/tracepoint interaction
  perf tui: Allow disabling the TUI on a per command basis in ~/.perfconfig
  ...

* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
  gta02: Use pcf50633 backlight driver instead of platform backlight driver.
  backlight: pcf50633: Register a pcf50633-backlight device in pcf50633 core driver.
  backlight: Add pcf50633 backlight driver
  backlight: 88pm860x_bl: fix error handling in pm860x_backlight_probe
  backlight: max8925_bl: Fix error handling path
  backlight: l4f00242t03: fix error handling in l4f00242t03_probe
  backlight: add S6E63M0 AMOLED LCD Panel driver
  backlight: adp8860: add support for ADP8861 & ADP8863
  backlight: mbp_nvidia_bl - Fix DMI_SYS_VENDOR for MacBook1,1
  backlight: Add Cirrus EP93xx backlight driver
  backlight: l4f00242t03: Fix regulators handling code in remove function
  backlight: fix adp8860_bl build errors
  backlight: new driver for the ADP8860 backlight parts
  backlight: 88pm860x_bl - potential memory leak
  backlight: mbp_nvidia_bl - add support for older MacBookPro and MacBook 6,1.
  backlight: Kconfig cleanup
  backlight: backlight_device_register() return ERR_PTR()

* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
  leds: Add mx31moboard MC13783 led support
  leds: Add mc13783 LED support
  leds: leds-ss4200: fix led_classdev_unregister twice in error handling
  leds: leds-lp3944: properly handle lp3944_configure fail in lp3944_probe
  leds: led-class: set permissions on max_brightness file to 0444
  leds: leds-gpio: Change blink_set callback to be able to turn off blinking
  leds: Add LED driver for the Soekris net5501 board
  leds: 88pm860x - fix checking in probe function

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging: (23 commits)
  hwmon: (lm75) Add support for the Texas Instruments TMP105
  hwmon: (ltc4245) Read only one GPIO pin
  hwmon: (dme1737) Add SCH5127 support
  hwmon: (tmp102) Don't always stop chip at exit
  hwmon: (tmp102) Fix suspend and resume functions
  hwmon: (tmp102) Various fixes
  hwmon: Driver for TI TMP102 temperature sensor
  hwmon: EMC1403 thermal sensor support
  hwmon: (applesmc) Add temperature sensor labels to sysfs interface
  hwmon: (applesmc) Add generic support for MacBook Pro 7
  hwmon: (applesmc) Add generic support for MacBook Pro 6
  hwmon: (applesmc) Add support for MacBook Pro 5,3 and 5,4
  hwmon: (tmp401) Reorganize code to get rid of static forward declarations
  hwmon: (tmp401) Use constants for sysfs file permissions
  hwmon: (adm1031) Allow setting update rate
  hwmon: Add description of the update_rate sysfs attribute
  hwmon: (lm90) Use programmed update rate
  hwmon: (f71882fg) Acquire I/O regions while we're working with them
  hwmon: (f71882fg) Code cleanup
  hwmon: (f71882fg) Use strict_stro(l|ul) instead of simple_strto$1
  ...

Add support for the Texas Instruments TMP105 temperature sensor
device.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti@ti.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Read only one of the GPIO pins as an analog voltage. The ADC can be
switched to a different GPIO pin at runtime, but this is not supported.

Previously, this driver would report the analog voltage of the currently
selected GPIO pin as all three GPIO voltages: in9_input, in10_input and
in11_input.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org

Add support for the hardware monitoring capabilities of the SCH5127
chip to the dme1737 driver.
Signed-off-by: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jeff Rickman <jrickman@myamigos.us>

Only stop the chip at driver exit if it was stopped when driver was
loaded. Leave it running otherwise.

Also restore the device configuration if probe failed, to not leave
the system in a dangling state.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>

Suspend and resume functions shouldn't overwrite the configuration
register. They should only alter the one bit they have to touch.

Also don't assume that register reads and writes always succeed.
Handle errors properly, shall they happen.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>

Fixes from my driver review:
http://lists.lm-sensors.org/pipermail/lm-sensors/2010-March/028051.html

Only the small changes are in there, more important changes will come
later separately as time permits.

* Drop the remnants of the now gone detect function
* The TMP102 has no known compatible chip
* Include the right header files
* Clarify why byte swapping of register values is needed
* Strip resolution info bit from temperature register value
* Set cache lifetime to 1/3 second
* Don't arbitrarily reject limit values; clamp as needed
* Make limit writing unconditional
* Don't check for transaction types the driver doesn't use
* Properly check for error when setting configuration
* Report error on failed probe
* Make the driver load automatically where needed
* Various other minor fixes
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Steven King <sfking@fdwdc.com>

Driver for the TI TMP102.

The TI TMP102 is similar to the LM75.  It differs from the LM75 by
having a 16-bit conf register and the temp registers have a minimum
resolution of 12 bits; the extended conf register can select 13-bit
resolution (which this driver does) and also change the update rate
(which this driver currently doesn't use).

[JD: Fix tmp102_exit tag, must be __exit, not __init.]
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Provides support for the EMC1403 thermal sensor. Only reporting of values
is supported. The various Moorestown specific extras to do with thermal
alerts and the like are not in this version of the driver.

Considerably edited and tidied up by Alan Cox, plus fixes and detection
bits from Jean Delvare.
Signed-off-by: Kalhan Trisal <kalhan.trisal@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>