- 10 Aug, 2015 40 commits
-
-
Krzysztof Kozlowski authored
commit 32c848e3 upstream. Status of enabling suspend mode for regulator was stored in bitmap-like long integer. However since adding support for S2MPU02 the number of regulators exceeded 32 so on devices with more than 32 regulators (S2MPU02 and S2MPS13) overflow happens when shifting the bit. This could lead to enabling suspend mode for completely different regulator than intended or to switching different regulator to other mode (e.g. from always enabled to controlled by PWRHOLD pin). Both cases could result in larger energy usage and issues when suspending to RAM. Fixes: 00e2573d ("regulator: s2mps11: Add support S2MPU02 regulator device") Reported-by:
Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Tejun Heo authored
commit 5f6c2d2b upstream. When a blkcg configuration is targeted to a partition rather than a whole device, blkg_conf_prep fails with -EINVAL; unfortunately, it forgets to put the gendisk ref in that case. Fix it. Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Bernhard Bender authored
commit 96849170 upstream. This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30 touch screen. Due to a missing delay between the RESET and SET_RATE commands, the touch screen may become unresponsive during system startup or driver loading. According to the DMC documentation, a delay is needed after the RESET command to allow the chip to complete its internal initialization. As this delay is not guaranteed, we had a system where the touch screen occasionally did not send any touch data. There was no other indication of the problem. The patch fixes the problem by adding a 150ms delay between the RESET and SET_RATE commands. Suggested-by:
Jakob Mustafa <jakob.mustafa@bytecmed.com> Signed-off-by:
Bernhard Bender <bernhard.bender@bytecmed.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Chris Metcalf authored
commit 3f81d244 upstream. We were previously using free_bootmem() and just getting lucky that nothing too bad happened. Signed-off-by:
Chris Metcalf <cmetcalf@ezchip.com> Signed-off-by:
-
Sascha Hauer authored
commit f6ee9b58 upstream. DMA transfers must be greater than the watermark level size. spi_imx->rx_wml and spi_imx->tx_wml contain the watermark level in 32bit words whereas struct spi_transfer contains the transfer len in bytes. Fix the check if DMA is possible for a transfer accordingly. This fixes transfers with sizes between 33 and 128 bytes for which previously was claimed that DMA is possible. Fixes: f62caccd (spi: spi-imx: add DMA support) Signed-off-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
-
Sifan Naeem authored
commit 6a806a21 upstream. Setting the Same Edge bit indicates to the spfi block to receive and transmit data on the same edge of the spfi clock, which in turn doubles the operating frequency of spfi. The maximum supported frequency is limited to 1/4th of the spfi input clock, but without this bit set the maximum would be 1/8th of the input clock. The current driver calculates the divisor with maximum speed at 1/4th of the input clock, this would fail if the requested frequency is higher than 1/8 of the input clock. Any requests for 1/8th of the input clock would still pass. Fixes: 8543d0e7 ("spi: img-spfi: Limit bit clock to 1/4th of input clock") Signed-off-by:
Sifan Naeem <sifan.naeem@imgtec.com> Signed-off-by:
-
NeilBrown authored
commit 34cab6f4 upstream. When we get a read error from the last working device, we don't try to repair it, and don't fail the device. We simple report a read error to the caller. However the current test for 'is this the last working device' is wrong. When there is only one fully working device, it assumes that a non-faulty device is that device. However a spare which is rebuilding would be non-faulty but so not the only working device. So change the test from "!Faulty" to "In_sync". If ->degraded says there is only one fully working device and this device is in_sync, this must be the one. This bug has existed since we allowed read_balance to read from a recovering spare in v3.0 Reported-and-tested-by:
Alexander Lyakas <alex.bolshoy@gmail.com> Fixes: 76073054 ("md/raid1: clean up read_balance.") Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit f9e5554c upstream. For 8000 series, we need to access the device to know what firmware to load. Before we do so, we need to prepare the device otherwise we might not be able to access the hardware. Fixes: c278754a21e6 ("iwlwifi: mvm: support family 8000 B2/C steps") Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Liad Kaufman authored
commit be88a1ad upstream. This fixes the byte order copying in the MAO (Mac Override Section) section from the PNVM, as the byte swapping is not required anymore in the 8000 family. Due to the byte swapping, the driver was reporting an incorrect MAC adddress. Signed-off-by:
Liad Kaufman <liad.kaufman@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 923a8c1d upstream. When BT is active, we want to avoid the shared antenna for management frame to make sure we don't disturb BT. There was a bug in that code because it chose the antenna BIT(ANT_A) where ANT_A is already a bitmap (0x1). This means that the antenna chosen in the end was ANT_B. While this is not optimal on devices with 2 antennas (it'd disturb BT), it is critical on single antenna devices like 3160 which couldn't connect at all when BT was active. This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=97181 Fixes: 34c8b24f ("iwlwifi: mvm: BT Coex - avoid the shared antenna for management frames") Signed-off-by:
-
Antonio Borneo authored
commit 6debce6f upstream. Current implementation of cp2112_raw_event() only accepts one data report at a time. If last received data report is not fully handled yet, a new incoming data report will overwrite it. In such case we don't guaranteed to propagate the correct incoming data. The trivial fix implemented here forces a single report at a time by requesting in cp2112_read() no more than 61 byte of data, which is the payload size of a single data report. Signed-off-by:
Antonio Borneo <borneo.antonio@gmail.com> Tested-by:
Ellen Wang <ellen@cumulusnetworks.com> Signed-off-by:
Jiri Kosina <jkosina@suse.com> Signed-off-by:
-
Jingju Hou authored
commit 9cd76049 upstream. pdev->dev.platform_data is not initialized if match is true in function sdhci_pxav3_probe. Just local variable pdata is assigned the return value from function pxav3_get_mmc_pdata(). static int sdhci_pxav3_probe(struct platform_device *pdev) { struct sdhci_pxa_platdata *pdata = pdev->dev.platform_data; ... if (match) { ret = mmc_of_parse(host->mmc); if (ret) goto err_of_parse; sdhci_get_of_property(pdev); pdata = pxav3_get_mmc_pdata(dev); } ... } Signed-off-by:
Jingju Hou <houjingj@marvell.com> Fixes: b650352d("mmc: sdhci-pxa: Add device tree support") Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Joakim Tjernlund authored
commit 8e91125f upstream. Support for 8BIT bus with was added some time ago to sdhci-esdhc but then missed to remove the 8BIT from the reserved bit mask which made 8BIT non functional. Fixes: 66b50a00 ("mmc: esdhc: Add support for 8-bit bus width and..") Signed-off-by:
Joakim Tjernlund <joakim.tjernlund@transmode.se> Signed-off-by:
-
Peng Fan authored
commit 7ac02036 upstream. We should not call dma_free_coherent if host->adma_table is NULL, otherwise may trigger panic. Fixes: d1e49f77 ("mmc: sdhci: convert ADMA descriptors to a...") Signed-off-by:
Peng Fan <van.freenix@gmail.com> Acked-by:
Adrian Hunter <adrian.hunter@intel.com> Signed-off-by:
-
Kishon Vijay Abraham I authored
commit 408806f7 upstream. DTO/DCRC errors were not being informed to the mmc core since commit ae4bf788 ("mmc: omap_hsmmc: consolidate error report handling of HSMMC IRQ"). This commit made sure 'end_trans' is never set on DTO/DCRC errors. This is because after this commit 'host->data' is checked after it has been cleared to NULL by omap_hsmmc_dma_cleanup(). Because 'end_trans' is never set, omap_hsmmc_xfer_done() is never invoked making core layer not to be aware of DTO/DCRC errors. Because of this any command invoked after DTO/DCRC error leads to a hang. Fix this by checking for 'host->data' before it is actually cleared. Fixes: ae4bf788 ("mmc: omap_hsmmc: consolidate error report handling of HSMMC IRQ") Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
Vignesh R <vigneshr@ti.com> Tested-by:
Andreas Fenkart <afenkart@gmail.com> Signed-off-by:
-
Alex Williamson authored
commit 46ebb7af upstream. This continues the attempt to fix commit fb170fb4 ("iommu/vt-d: Introduce helper functions to make code symmetric for readability"). The previous attempt in commit 71684406 ("iommu/vt-d: Detach domain *only* from attached iommus") overlooked the fact that dmar_domain.iommu_bmp gets cleared for VM domains when devices are detached: intel_iommu_detach_device domain_remove_one_dev_info domain_detach_iommu The domain is detached from the iommu, but the iommu is still attached to the domain, for whatever reason. Thus when we get to domain_exit(), we can't rely on iommu_bmp for VM domains to find the active iommus, we must check them all. Without that, the corresponding bit in intel_iommu.domain_ids doesn't get cleared and repeated VM domain creation and destruction will run out of domain IDs. Meanwhile we still can't call iommu_detach_domain() on arbitrary non-VM domains or we risk clearing in-use domain IDs, as 71684406 attempted to address. It's tempting to modify iommu_detach_domain() to test the domain iommu_bmp, but the call ordering from domain_remove_one_dev_info() prevents it being able to work as fb170fb4 seems to have intended. Caching of unused VM domains on the iommu object seems to be the root of the problem, but this code is far too fragile for that kind of rework to be proposed for stable, so we simply revert this chunk to its state prior to fb170fb4. Fixes: fb170fb4 ("iommu/vt-d: Introduce helper functions to make code symmetric for readability") Fixes: 71684406 ("iommu/vt-d: Detach domain *only* from attached iommus") Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Cc: Jiang Liu <jiang.liu@linux.intel.com> Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Steven Rostedt (Red Hat) authored
commit e3eea140 upstream. Commit 4104d326 ("ftrace: Remove global function list and call function directly") simplified the ftrace code by removing the global_ops list with a new design. But this cleanup also broke the filtering of PIDs that are added to the set_ftrace_pid file. Add back the proper hooks to have pid filtering working once again. Reported-by:
Matt Fleming <matt@console-pimps.org> Reported-by:
Richard Weinberger <richard.weinberger@gmail.com> Tested-by:
Steven Rostedt <rostedt@goodmis.org> Signed-off-by:
-
Eric W. Biederman authored
commit fe78fcc8 upstream. The handling of in detach_mounts of unmounted but connected mounts is buggy and can lead to an infinite loop. Correct the handling of unmounted mounts in detach_mount. When the mountpoint of an unmounted but connected mount is connected to a dentry, and that dentry is deleted we need to disconnect that mount from the parent mount and the deleted dentry. Nothing changes for the unmounted and connected children. They can be safely ignored. Fixes: ce07d891 mnt: Honor MNT_LOCKED when detaching mounts Signed-off-by:
"Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by:
-
Eric W. Biederman authored
commit f2d0a123 upstream. rmdir mntpoint will result in an infinite loop when there is a mount locked on the mountpoint in another mount namespace. This is because the logic to test to see if a mount should be disconnected in umount_tree is buggy. Move the logic to decide if a mount should remain connected to it's mountpoint into it's own function disconnect_mount so that clarity of expression instead of terseness of expression becomes a virtue. When the conditions where it is invalid to leave a mount connected are first ruled out, the logic for deciding if a mount should be disconnected becomes much clearer and simpler. Fixes: e0c9c0af mnt: Update detach_mounts to leave mounts connected Fixes: ce07d891 mnt: Honor MNT_LOCKED when detaching mounts Signed-off-by:
-
Uwe Kleine-König authored
commit 9571b25d upstream. imx1_pinconf_set assumes that the array of pins in struct imx1_pinctrl_soc_info can be indexed by pin id to get the pinctrl_pin_desc for a pin. This used to be correct up to commit 607af165 which removed some entries from the array and so made it wrong to access the array by pin id. The result of this bug is a wrong pin name in the output for small pin ids and an oops for the bigger ones. This patch is the result of a discussion that includes patches by Markus Pargmann and Chris Ruehl. Fixes: 607af165 ("pinctrl: i.MX27: Remove nonexistent pad definitions") Reported-by:
Chris Ruehl <chris.ruehl@gtsys.com.hk> Signed-off-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by:
Markus Pargmann <mpa@pengutronix.de> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Tom Hughes authored
commit 4479004e upstream. If we don't do this, and we then fail to recreate the debugfs directory during a mode change, then we will fail later trying to add stations to this now bogus directory: BUG: unable to handle kernel NULL pointer dereference at 0000006c IP: [<c0a92202>] mutex_lock+0x12/0x30 Call Trace: [<c0678ab4>] start_creating+0x44/0xc0 [<c0679203>] debugfs_create_dir+0x13/0xf0 [<f8a938ae>] ieee80211_sta_debugfs_add+0x6e/0x490 [mac80211] Signed-off-by:
Tom Hughes <tom@compton.nu> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Pankaj Dev authored
commit 56551da9 upstream. Incorrect register offset used for sthi407 clockgenC Signed-off-by:
Pankaj Dev <pankaj.dev@st.com> Signed-off-by:
Gabriel Fernandez <gabriel.fernandez@linaro.org> Fixes: 51306d56 ("clk: st: STiH407: Support for clockgenC0") Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Gabriel Fernandez authored
commit 3be6d8ce upstream. This patch fixes the mux bit-setting for ClockgenA9. Signed-off-by:
-
Giuseppe Cavallaro authored
commit 0f4f2afd upstream. While proving lock, the following warning happens and it is fixed after initializing lock in the setup function INFO: trying to register non-static key. the code is fine but needs lockdep annotation. turning off the locking correctness validator. CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.10.27-02861-g39df285-dirty #33 [<c00154ac>] (unwind_backtrace+0x0/0xf4) from [<c0011b50>] (show_stack+0x10/0x14) [<c0011b50>] (show_stack+0x10/0x14) from [<c00689ac>] (__lock_acquire+0x900/0xb14) [<c00689ac>] (__lock_acquire+0x900/0xb14) from [<c0069394>] (lock_acquire+0x68/0x7c) [<c0069394>] (lock_acquire+0x68/0x7c) from [<c04958f8>] (_raw_spin_lock_irqsave+0x48/0x5c) [<c04958f8>] (_raw_spin_lock_irqsave+0x48/0x5c) from [<c0381e6c>] (clk_gate_endisable+0x28/0x88) [<c0381e6c>] (clk_gate_endisable+0x28/0x88) from [<c0381ee0>] (clk_gate_enable+0xc/0x14) [<c0381ee0>] (clk_gate_enable+0xc/0x14) from [<c0386c68>] (flexgen_enable+0x28/0x40) [<c0386c68>] (flexgen_enable+0x28/0x40) from [<c037f260>] (__clk_enable+0x5c/0x9c) [<c037f260>] (__clk_enable+0x5c/0x9c) from [<c037f558>] (clk_enable+0x18/0x2c) [<c037f558>] (clk_enable+0x18/0x2c) from [<c064a1dc>] (st_lpc_of_register+0xc0/0x248) [<c064a1dc>] (st_lpc_of_register+0xc0/0x248) from [<c0649e44>] (clocksource_of_init+0x34/0x58) [<c0649e44>] (clocksource_of_init+0x34/0x58) from [<c0637ddc>] (sti_timer_init+0x10/0x18) [<c0637ddc>] (sti_timer_init+0x10/0x18) from [<c06343f8>] (time_init+0x20/0x30) [<c06343f8>] (time_init+0x20/0x30) from [<c0632984>] (start_kernel+0x20c/0x2e8) [<c0632984>] (start_kernel+0x20c/0x2e8) from [<40008074>] (0x40008074) Signed-off-by:
Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
-
Seymour, Shane M authored
commit e7ac6c66 upstream. Two SLES11 SP3 servers encountered similar crashes simultaneously following some kind of SAN/tape target issue: ... qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-8009:3: DEVICE RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: DEVICE RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8009:3: TARGET RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: TARGET RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8012:3: BUS RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-802b:3: BUS RESET SUCCEEDED nexus=3:0:2. qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8018:3: ADAPTER RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-00af:3: Performing ISP error recovery - ha=ffff88bf04d18000. rport-3:0-0: blocked FC remote port time out: removing target and saving binding qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8017:3: ADAPTER RESET SUCCEEDED nexus=3:0:2. rport-2:0-0: blocked FC remote port time out: removing target and saving binding sg_rq_end_io: device detached BUG: unable to handle kernel NULL pointer dereference at 00000000000002a8 IP: [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 PGD 7e6586f067 PUD 7e5af06067 PMD 0 [1739975.390354] Oops: 0002 [#1] SMP CPU 0 ... Supported: No, Proprietary modules are loaded [1739975.390463] Pid: 27965, comm: ABCD Tainted: PF X 3.0.101-0.29-default #1 HP ProLiant DL580 Gen8 RIP: 0010:[<ffffffff8133b268>] [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP: 0018:ffff8839dc1e7c68 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff883f0592fc00 RCX: 0000000000000090 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000138 RBP: 0000000000000138 R08: 0000000000000010 R09: ffffffff81bd39d0 R10: 00000000000009c0 R11: ffffffff81025790 R12: 0000000000000001 R13: ffff883022212b80 R14: 0000000000000004 R15: ffff883022212b80 FS: 00007f8e54560720(0000) GS:ffff88407f800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00000000000002a8 CR3: 0000007e6ced6000 CR4: 00000000001407f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process ABCD (pid: 27965, threadinfo ffff8839dc1e6000, task ffff883592e0c640) Stack: ffff883f0592fc00 00000000fffffffa 0000000000000001 ffff883022212b80 ffff883eff772400 ffffffffa03fa309 0000000000000000 0000000000000000 ffffffffa04003a0 ffff883f063196c0 ffff887f0379a930 ffffffff8115ea1e Call Trace: [<ffffffffa03fa309>] st_open+0x129/0x240 [st] [<ffffffff8115ea1e>] chrdev_open+0x13e/0x200 [<ffffffff811588a8>] __dentry_open+0x198/0x310 [<ffffffff81167d74>] do_last+0x1f4/0x800 [<ffffffff81168fe9>] path_openat+0xd9/0x420 [<ffffffff8116946c>] do_filp_open+0x4c/0xc0 [<ffffffff8115a00f>] do_sys_open+0x17f/0x250 [<ffffffff81468d92>] system_call_fastpath+0x16/0x1b [<00007f8e4f617fd0>] 0x7f8e4f617fcf Code: eb d3 90 48 83 ec 28 40 f6 c6 04 48 89 6c 24 08 4c 89 74 24 20 48 89 fd 48 89 1c 24 4c 89 64 24 10 41 89 f6 4c 89 6c 24 18 74 11 <f0> ff 8f 70 01 00 00 0f 94 c0 45 31 ed 84 c0 74 2b 4c 8d a5 a0 RIP [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP <ffff8839dc1e7c68> CR2: 00000000000002a8 Analysis reveals the cause of the crash to be due to STp->device being NULL. The pointer was NULLed via scsi_tape_put(STp) when it calls scsi_tape_release(). In st_open() we jump to err_out after scsi_block_when_processing_errors() completes and returns the device as offline (sdev_state was SDEV_DEL): 1180 /* Open the device. Needs to take the BKL only because of incrementing the SCSI host 1181 module count. */ 1182 static int st_open(struct inode *inode, struct file *filp) 1183 { 1184 int i, retval = (-EIO); 1185 int resumed = 0; 1186 struct scsi_tape *STp; 1187 struct st_partstat *STps; 1188 int dev = TAPE_NR(inode); 1189 char *name; ... 1217 if (scsi_autopm_get_device(STp->device) < 0) { 1218 retval = -EIO; 1219 goto err_out; 1220 } 1221 resumed = 1; 1222 if (!scsi_block_when_processing_errors(STp->device)) { 1223 retval = (-ENXIO); 1224 goto err_out; 1225 } ... 1264 err_out: 1265 normalize_buffer(STp->buffer); 1266 spin_lock(&st_use_lock); 1267 STp->in_use = 0; 1268 spin_unlock(&st_use_lock); 1269 scsi_tape_put(STp); <-- STp->device = 0 after this 1270 if (resumed) 1271 scsi_autopm_put_device(STp->device); 1272 return retval; The ref count for the struct scsi_tape had already been reduced to 1 when the .remove method of the st module had been called. The kref_put() in scsi_tape_put() caused scsi_tape_release() to be called: 0266 static void scsi_tape_put(struct scsi_tape *STp) 0267 { 0268 struct scsi_device *sdev = STp->device; 0269 0270 mutex_lock(&st_ref_mutex); 0271 kref_put(&STp->kref, scsi_tape_release); <-- calls this 0272 scsi_device_put(sdev); 0273 mutex_unlock(&st_ref_mutex); 0274 } In scsi_tape_release() the struct scsi_device in the struct scsi_tape gets set to NULL: 4273 static void scsi_tape_release(struct kref *kref) 4274 { 4275 struct scsi_tape *tpnt = to_scsi_tape(kref); 4276 struct gendisk *disk = tpnt->disk; 4277 4278 tpnt->device = NULL; <<<---- where the dev is nulled 4279 4280 if (tpnt->buffer) { 4281 normalize_buffer(tpnt->buffer); 4282 kfree(tpnt->buffer->reserved_pages); 4283 kfree(tpnt->buffer); 4284 } 4285 4286 disk->private_data = NULL; 4287 put_disk(disk); 4288 kfree(tpnt); 4289 return; 4290 } Although the problem was reported on SLES11.3 the problem appears in linux-next as well. The crash is fixed by reordering the code so we no longer access the struct scsi_tape after the kref_put() is done on it in st_open(). Signed-off-by:
Shane Seymour <shane.seymour@hp.com> Signed-off-by:
Darren Lavender <darren.lavender@hp.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.com> Acked-by:
Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Tony Battersby authored
commit 0c958ecc upstream. Fix a memory leak with scsi-mq triggered by commands with large data transfer length. __sg_alloc_table() sets both table->nents and table->orig_nents to the same value. When the scatterlist is DMA-mapped, table->nents is overwritten with the (possibly smaller) size of the DMA-mapped scatterlist, while table->orig_nents retains the original size of the allocated scatterlist. scsi_free_sgtable() should therefore check orig_nents instead of nents, and all code that initializes sdb->table without calling __sg_alloc_table() should set both nents and orig_nents. Fixes: d285203c ("scsi: add support for a blk-mq based I/O path.") Signed-off-by:
Tony Battersby <tonyb@cybernetics.com> Reviewed-by:
Christoph Hellwig <hch@lst.de> Reviewed-by:
Ewan D. Milne <emilne@redhat.com> Signed-off-by:
-
Jens Axboe authored
commit 1278dd68 upstream. Commit 1e6f2416 changed the scsi sysfs 'queue_depth' code to rejects depths higher than the scsi host template setting. But lots of hosts set this to 1, and update the settings in the scsi host when the controller/devices probing happens. This breaks (at least) mpt2sas and mpt3sas runtime setting of queue depth, returning EINVAL for all settings but '1'. And once it's set to 1, there's no way to go back up. Fixes: 1e6f2416 "scsi: don't allow setting of queue_depth bigger than can_queue" Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Reviewed-by:
-
Marc Zyngier authored
commit 591e5bec upstream. The GICv3 ITS architecture allows a given [DevID, EventID] pair to be translated to a [LPI, Collection] pair, where DevID is the device writing the MSI, EventID is the payload being written, LPI is the actual interrupt number, and Collection is roughly equivalent to a target CPU. Each LPI can be mapped to a separate collection, but the ITS driver insists on maintaining the collection on a device basis, instead of doing it on a per interrupt basis. This is obviously flawed, and this patch fixes it by adding a per interrupt index that indicates which collection number is in use. Reported-by:
Ian Campbell <ian.campbell@citrix.com> Signed-off-by:
Marc Zyngier <marc.zyngier@arm.com> Cc: <linux-arm-kernel@lists.infradead.org> Cc: Jason Cooper <jason@lakedaemon.net> Link: http://lkml.kernel.org/r/1437126402-11677-1-git-send-email-marc.zyngier@arm.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Mike Snitzer authored
commit 621739b0 upstream. This reverts commit 9a0e609e. (Resolved a conflict during revert due to commit bfebd1cd that came after) This revert is motivated by a couple failure reports on request-based DM multipath testbeds: 1) Netapp reported that their multipath fault injection test under heavy IO load can stall longer than 300 seconds. 2) IBM reported elevated lock contention in their testbed (likely due to increased back pressure due to IO not being dispatched as quickly): https://www.redhat.com/archives/dm-devel/2015-July/msg00057.htmlSigned-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Peter Zijlstra authored
commit a833581e upstream. Mikulas reported his K6-3 not booting. This is because the static_key API confusion struck and bit Andy, this wants to be static_key_false(). Reported-by:
Mikulas Patocka <mpatocka@redhat.com> Tested-by:
Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrea Arcangeli <aarcange@redhat.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Arnaldo Carvalho de Melo <acme@kernel.org> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Kees Cook <keescook@chromium.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul Mackerras <paulus@samba.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Cc: Vince Weaver <vince@deater.net> Cc: hillf.zj <hillf.zj@alibaba-inc.com> Fixes: a6673429 ("perf/x86: Add /sys/devices/cpu/rdpmc=2 to allow rdpmc for all tasks") Link: http://lkml.kernel.org/r/20150709172338.GC19282@twins.programming.kicks-ass.netSigned-off-by:
Ingo Molnar <mingo@kernel.org> Signed-off-by:
-
Takashi Iwai authored
commit 649ccd08 upstream. MacBook Pro 5,2 with ALC889 codec had already a fixup entry, but this seems not working correctly, a fix for pin NID 0x15 is needed in addition. It's equivalent with the fixup for MacBook Air 1,1, so use this instead. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102131Reported-and-tested-by:
Jeffery Miller <jefferym@gmail.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Yao-Wen Mao authored
commit 2d1cb7f6 upstream. Add the correct dB ranges of Bose Companion 5 and Drangonfly DAC 1.2. Signed-off-by:
Yao-Wen Mao <yaowen@google.com> Signed-off-by:
-
Takashi Iwai authored
commit 3a05d12f upstream. Dell Vostro 5480 (1028:069a) needs the very same quirk used for Vostro 5470 model to make bass speakers properly working. Reported-and-tested-by:
Paulo Roberto de Oliveira Castro <p.oliveira.castro@gmail.com> Signed-off-by:
-
Takashi Iwai authored
commit b9d9c9ef upstream. Toshiba Satellite S50D has another model with a different PCI SSID (1179:fa93) while the previous fixup was for 1179:fa91. Adjust the fixup entry with SND_PCI_QUIRK_MASK() to match with both devices. Reported-by:
Tim Sample <timsample@gmail.com> Signed-off-by:
-
David Henningsson authored
commit cba59972 upstream. Without this patch, the headset mic will not work on this machine. BugLink: https://bugs.launchpad.net/bugs/1476987Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
-
Aaron Plattner authored
commit 6c3d9119 upstream. Vendor ID 0x10de007d is used by a yet-to-be-named GPU chip. This chip also has the 2-ch audio swapping bug, so patch_nvhdmi is appropriate here. Signed-off-by:
Aaron Plattner <aplattner@nvidia.com> Signed-off-by:
-
Maruthi Srinivas Bayyavarapu authored
commit 5022813d upstream. Fixes audio problems on newer asics Signed-off-by:
Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com> Signed-off-by:
-
Mateusz Sylwestrzak authored
commit 0420694d upstream. Acer Aspire V5 with the ALC282 codec is given the wrong value for the 0x19 PIN by the laptop's BIOS. Overriding it with the correct value adds support for the headset microphone which would not otherwise be visible in the system. The fix is based on commit 7819717b with a similar quirk for Acer Aspire with the ALC269 codec. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96201Signed-off-by:
Mateusz Sylwestrzak <matisec7@gmail.com> Signed-off-by:
-
Takashi Iwai authored
commit 67756e31 upstream. With the nonatomic PCM ops, the system may spew lockdep warnings like: ============================================= [ INFO: possible recursive locking detected ] 4.2.0-rc1-jeejaval3 #12 Not tainted --------------------------------------------- aplay/4029 is trying to acquire lock: (snd_pcm_link_rwsem){.+.+.+}, at: [<ffffffff816fd473>] snd_pcm_stream_lock+0x43/0x60 but task is already holding lock: (snd_pcm_link_rwsem){.+.+.+}, at: [<ffffffff816fcf29>] snd_pcm_action_nonatomic+0x29/0x80 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(snd_pcm_link_rwsem); lock(snd_pcm_link_rwsem); Although this is false-positive as the rwsem is taken always as read-only for these code paths, it's certainly annoying to see this at any occasion. A simple fix is to use down_read_nested() in snd_pcm_stream_lock() that can be called inside another lock. Reported-by:
Vinod Koul <vinod.koul@intel.com> Reported-by:
Jeeja Kp <jeeja.kp@intel.com> Tested-by:
-
Takashi Iwai authored
commit 4d0e6775 upstream. When a monitor stream is active, the next PCM stream access results in EBUSY error because of the check in line6_stream_start(). Fix this by just skipping the submission of pending URBs when the stream is already running instead. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=101431Signed-off-by:
-
