Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch will also change behavior of rx_beacons statistic.
Instead of collecting all received beacons, it will collect only
ours. This, IMO make more sense, since for troubleshooting we will
need to know count of our beacons, or both.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

this function is used by most ath driver, so it can be moved here.
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

While registering the driver with cfg80211, update the threshold
value and retry limit to cfg80211.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

bit 14 is actually reserved and bit 12 & 13 should be used for
11ac capability in fw_cap_info.

Cc: <stable@vger.kernel.org> # 3.9+
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This fixes bug found by the kbuild test robot:

tree:   git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git master
head:   1e2f9295
commit: 1cbbcb08 [135/140] wil6210: prefetch head of packet
config: make ARCH=microblaze allyesconfig

All error/warnings:

   drivers/net/wireless/ath/wil6210/txrx.c: In function 'wil_vring_reap_rx':
>> drivers/net/wireless/ath/wil6210/txrx.c:381:2: error: implicit declaration of function 'prefetch' [-Werror=implicit-function-declaration]
     prefetch(skb->data);
     ^
   cc1: some warnings being treated as errors

vim +/prefetch +381 drivers/net/wireless/ath/wil6210/txrx.c

   375                  wil_err(wil, "Rx size too large: %d bytes!\n", dmalen);
   376                  kfree_skb(skb);
   377                  return NULL;
   378          }
   379          skb_trim(skb, dmalen);
   380
 > 381          prefetch(skb->data);
   382
   383          wil_hex_dump_txrx("Rx ", DUMP_PREFIX_OFFSET, 16, 1,
   384                            skb->data, skb_headlen(skb), false);
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Prevent a possible overflow condition which results in occasional
bad IQ coefficients and EVM numbers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This patch fixes a bug in the TX IQ calibration post
processing routine because of which the driver disables
TX IQ correction even though the calibration results
are valid. This fix is applicable for all chips in the
AR9003 family.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

debug_sta.c: ath_debug_rate_stats() error: buffer overflow 'rstats->ht_stats' 24 <= 24

Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When removing the card the driver still tries to access registers
in the device. This patch adds another state for the bus that
indicates the device is no longer reachable. This avoids errors
accessing it while cleaning up the driver.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

For scheduled scan results the driver does a escan to obtain BSS
details from the firmware. However, the escan uses a dynamically
determined function. This needs to be set appropriately when handling
scheduled scan results to avoid NULL pointer access.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Rework function to allow only bcm4329 in case of chip backplane
type being sonics sillicon backplane.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The firmware download code has been restructured so the reset vector
does not need to be stored in a structure, but keep it on the stack
to be passed to exit download function.
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The original core reset and disable routines do not work always
on running system. These routines were updated to properly reset
a core. When module is unloaded the device is put into download
state where all necessary cores have been reset. This will make
sure the device is in idle mode after module unload.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

New bus layers like pcie require nvram parsing routines which are
the same routines as being used by sdio. Make these routines common
in the new file nvram.c. Update sdio to use these routines and
simplify the nvram upload process. Also add memory validation check
for downloaded firmware and nvram in debug mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Keeping this as 0 is ok according to spec section 9.7.11
as this means the limits are according to the Tx/Rx
supported MCS x NSS bitmap. Initially we've set these as
there were concerns of interop issues but these turned out
to be false.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If we try to write NVM that do not exist, the function will return
uninitialized value. fixed.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add an inline helper function for getting an RX packet's
length or payload length and use it throughout the code
(most of which I did using an spatch.)

While at it, adjust some code, and remove a bogus comment
from the dvm calibration code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All beamformee supporting chips have the ability to support
VHT NDP in up to 4 STSs. So change the published beamformee
STS cap accordingly to 3 as it should be Nsts-1.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The request of SMPS issued by the Thermal Throttling code
was not reset when we disassociated - fix that.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

It's a bit strange to treat an array as a pointer, so use proper
array indexing instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If the length isn't set it means we want all the SRAM.
Also - this is perfectly valid to partially dump starting
at offset 0.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Discovered by klocwork

Array 'iwl_rate_mcs' of size 15 may use index value(s) -1
  * rs.c:2562: index = iwl_hwrate_to_plcp_idx(rate)
    * rs.c:2562: Result of function call 'iwl_hwrate_to_plcp_idx(rate)' is '[-1,14]'
  * rs.c:2565: Array 'iwl_rate_mcs' size is 15.
  * rs.c:2565: Possible attempt to access element -1 of array 'iwl_rate_mcs'.

While at it stop using index = -1 and always use IWL_RATE_INVALID
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Some NIC comes with more than the 4 NVM (non volative
memory) sections described in the nvm_to_read array.
These NICs usually get their NVM from an external file
fetched from userland during init.
We already parsed the file, but sent to the NIC only 4 NVM
sections whereas there could be more sections in the file.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Since seq_number is incremented right after using
it, so printed seq_ctrl was actually the next
one to be used.

Fix it by incrementing the seq_number only later,
before saving it.

Additionally, use the IEEE80211_SEQ_TO_SN macro
in order to print the actual sequence number.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Enabling the oscillator consumes slightly more power (100uA)
but allows to make sure that we exit from L1 on time.

Not doing so might lead to a PCIe specification violation
since we might wake up from L1 at the wrong time.
This issue has been identified on 3160 and 7260 only.
On older NICs L1 off is not enabled, on newer NICs (7265),
the issue is fixed.

When the bug occurs the user sees that the NIC has
disappeared from the PCI bridge, any access to the device
returns 0xff.

This fixes:
	https://bugzilla.kernel.org/show_bug.cgi?id=64541

and has been extensively discussed here:
	http://markmail.org/thread/mfmpzqt3r333n4bo

Cc: stable@vger.kernel.org [3.10+]
Fixes: 99cd4714 ("iwlwifi: add 7000 series device configuration")
Reported-and-tested-by: wzyboy <wzyboy@wzyboy.org>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The call to clamp_t() first truncates the variable signed 8 bit and as a
result, the actual clamp is a no-op.

Fixes: 0d78156e ('p54: improve site survey')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Delete a variable that is at most only assigned to a constant, but never
used otherwise.

A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
type T;
identifier i;
constant c;
@@

-T i;
<... when != i
-i = c;
...>
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Global Transmission Timeout interrupts are generated by
the HW when transmission of a frame fails - this is done
based on the threshold programmed in the AR_GTXTO register.

Currently, even though the interrupt is enabled for all chips,
it is not handled in the driver. This patch handles GTT events
for AR9003 and above chips, checking if the MAC/BB has hung
after successive GTT interrupts crosses a threshold (5).

This can be enabled for the older chips in the AR9002 family once
appropriate HW hang checks are implemented for them.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is no need to do this and we can avoid
an unused variable warning when CONFIG_ATH9K_WOW is
not selected.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This would be useful when debugging RX performance issues.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Also, rename node_stat to node_aggr.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>